Search Documents

By Jean Habimana

Complex and distinct geological units spread along the 7-mile long 30-ft inside diameter Upper Rouge Tunnel CSO Control Project in Detroit, Michigan. Its construction is divided in two tunnel construction packages: The South Tunnel, to be driven in finely laminated weak TG Limy Shale, will be excavated by a shielded TBM with precast concrete segmental lining, while the North tunnel, predominantly in a relatively more competent geologic formation Antrim Shale, will be excavated by a main beam TBM with a two-pass lining system. The adits and deaeration chambers will be excavated by sequential excavation method. This paper addresses the process of selecting excavation methods and lining systems for shafts, tunnels, connecting adits, and deaeration chambers.

By F. J. Sotillo

"Scrubbing both horizontal (drum) and vertical (attrition) are considered simple unit operations in the beneficiation of phosphate ores. In general, the operating conditions are fixed at high solids content based on the experience of the engineering or equipment manufacturing company responsible of designing this beneficiation step. Nevertheless, scrubbing is a complex unit operation designed to clean the surfaces of phosphate mineral particles of slimes, break loose weak inclusions or attached particles of impurities, and break aggregates of clayish material. Therefore, it is considered that as high solids content as possible should be used to enhance particle-particle interactions (impact and rubbing) without taking into consideration the rheology of the system. However, scrubbing unit operations design requires studying the balance between the increase of particle-particle interactions with the cushion effect that may occur when slimes, clays and fines decrease the availability of free water increasing the apparent viscosity of the phosphate slurry up to that of a paste consistency. This paper presents data from laboratory tests to determine the best operating conditions for the design of these unit operations based on the highest P2O5 grade obtained with the lowest impurities for different size fractions. INTRODUCTION In the beneficiation of phosphate ores, unit operations such as horizontal scrubbing (drum) and vertical scrubbing (attrition) are considered simple unit operations. Therefore, little attention is given to the design of horizontal and vertical scrubbing during the basic engineering studies, and the detail engineering stage, the manufacturers recommending “standard” units and operating conditions based on their experience. Due diligence of several beneficiation phosphate plants at industrial scale indicates that a deficient scrubbing of the phosphate ore results in significant problems in downstream unit operations, such as classification, clarification, gravity separation, magnetic separation, flotation, dewatering, and filtration. Scrubbing is in fact a complex unit operation designed to clean the surfaces of phosphate mineral particles of slimes (clays and fines), break loose weak inclusions or attached particles of impurities, and break aggregates of clayish material. Two phenomena occur, the particle-particle interaction (impact and rubbing), and the rheological effects of releasing significant amount of fines into the slurry. Therefore, high solids contents are recommended to enhance the particle-particle interactions, which may result in a change in the rheological regime of the system due to the slimes, clays, and fines decreasing the availability of free water. This increases the apparent viscosity of the system up to that of paste consistency resulting in a cushion effect that suppresses scrubbing. Under these conditions, not all fines are release and rejected (deslimed), downstream unit operations being affected by the release of clays, resulting in P2O5 losses."

Jan 1, 2017

By James L. Weeks

Introduction This paper attempts to summarize some of the major criticisms of drug testing. Eight problems with drug testing are discussed. These are: • It does not measure something employers have a reasonable need to know, • It is a distortion of priorities, • Drug use is not known to be associated with increased risk of occupational injuries, • Drug testing is proposed as a dangerously simplistic solution to poorly conceived problems, • In the absence of safeguards, it is unacceptably inaccurate, • In the absence of treatment commitments and confidentiality protection for persons dependent on drugs, it is an unethical practice of medicine, • Drug testing is an invasion of privacy, and • It will have a negative effect on treatment of persons with drug or alcohol dependencies. Employers' need to know It does not measure something employers have a reasonable need to know. It is reasonable for employers and fellow workers to want to know if workers are functionally impaired (intoxicated) while on the job. Drug testing does not measure impairment. It measures the concentration of drug metabolities in urine or blood. Unlike measurements of blood alcohol concentration (BAC), drug metabolites are not correlated with impairment or intoxication. They indicate only drug use in the one to two weeks before a urine sample. And, in some instances, they indicate chronic use. Impairment caused by drug use, on the other hand, occurs immediately and declines rapidly within hours. Drug metabolites may linger for days afterwards. Drug metabolite concentrations in urine are a function of (Morgan, 1984; Schartz and Hawks, 1985; MMWR, 1983): • the amount and purity of drug consumed before taking the test, • when the drug was consumed, • whether the person was a chronic user, in which case a certain amount of drug metabolites would be stored in body fat and slowly released, • the person's metabolic rate, and • for metabolites in urine, any dilution effects of urine. Only the first two factors has

Jan 11, 1987

By M. R. Yalamanchili

The in-situ FTIR/IRS technique has been used to spectroscopically characterize interfacial water near a hydrophilic surface. Interfacial water was examined spectroscopically over known distances from the surface of a silicon single crystal by appropriate design of the geometry and optics of the internal reflection system. The in-situ FTIR/IRS spectra of interfacial water were examined by consideration of the 0 -H stretching region (3000 -3800 cm-1) associated with the vibrational spectra of water. The broad peak: in this region which describes the interfacial water structure was deconvoluted in order to isolate the overlapping spectral features of the interfacial water. Preliminary spectral results indicate the prevalence of an ice-like water structure (-3200 cm-!) at the silicon surface. Importantly, it appears that the interfacial water structure may extend a considerable distance (several tens of molecular layers) from the surface as established from the spectroscopic depth profile measurements which show that the free OH stretch at 3600 cm-1 becomes very significant at distances from the surface exceeding 400 nm.

Jan 1, 1995

By Geoffrey Hughes

The Narragansett Bay Commission (NBC) is a regional sewer authority that serves ten communities in the Providence, Rhode Island metropolitan area. From 1992 to 1999, the NBC developed a comprehensive facilities plan to abate Combined Sewer Overflow (CSO) pollution in the Upper Narragansett Bay. The plan underwent many major evolutions during this period, most notably the addition of a stakeholder?s process by which NBC demonstrated a site-specific plan to control the pollutants and meet water quality standards. The favored solution consisted of deep tunnel storage with treatment at existing wastewater facilities that had been recently upgraded. In 1999, a final plan was accepted which included two tunnels, five CSO interceptors, twelve sewer separation projects, a wetland facility, and a wastewater treatment facility upgrade. The program is to be constructed over 20 years in three sequential phases (Figure 1). Phase I of the program includes a 4,963 m (16,284 ft) long, 7.9 m (26 ft) diameter, 70.1 m (230 ft) deep storage tunnel; seven drop shafts with connecting adits; ancillary facilities; and a pump station. Construction of Phase I began in 2001 and is expected to be operational by October 2008. This paper focuses on design and construction of the Fields Point Tunnel Pump Station (FPTPS)located at the south end of the main spine tunnel. A189 Ml/day (50 MGD) pump station is required to lift CSO flows from the tunnel to the Fields Point Wastewater Treatment Facility (FPWWTF). The pumps are to be housed in a 35.6 m × 18.6 m ×20.7 m (117 ft × 61 ft × 68 ft), 91.4 m (300 ft) deep cavern excavated in a complex meta-sedimentary rock of the Rhode Island Formation, and connected to the surface by 9.7 m (32 ft) and 3.4 m (11 ft) diameter shafts. Factors which influenced selection of the size, configuration and location of facilities included the preferred arrangement of pumps, critical aspects of site geology, and estimated cost. Technical and value engineering reviews also affected the final design. Following Notice to Proceed (NTP), concerns were raised by the contractor regarding constructability and design. Additional geotechnical investigation and independent engineering review were employed to validate the design assumptions. The cavern was successfully excavated and sup-ported in rock, completed on schedule and within budget in 2005. In 1992 the NBC retained Louis Berger Group (LBG) as Program Manager (PM) for the CSO Abatement Program. LBG thereafter formed a design team including: Jacobs Engineering Group(JEG) as the designer for underground structures and near surface collection facilities; Black and Veatch(B&V) to design the pumping system and associated facilities; Haley and Aldrich (H&A) to oversee the geotechnical program; and Malcolm Pirnie to design the system-wide instrumentation and control system. Construction management, resident engineering, and inspection services were provided by the joint venture Gilbane/Jacobs Associates (G/J).

Jan 1, 2008

By J. D. Patsey, G. T. Lineberry

Introduction A computer program was developed for analyzing drum-type hoists before modifying an existing system or designing a new one. Its use permits the preliminary evaluation of a system before seeking technical assistance from mine hoist designers and manufacturers. The user-friendly program accepts a variety of data and analyzes hoisting systems for any balance state. The program can be used to calculate skip capacity to yield a desired production rate, solve for drum face width, select a permissible wire rope, estimate total horsepower of the hoist plant, and estimate annual power cost. Whether required for a large mining complex or for a relatively small operation, a hoisting system must be carefully designed to ensure the efficient, reliable, and safe flow of material. Because shaft sinking and hoist installation can total between 2.5% and 3% of the cost of opening a deep mine, proper hoist selection is critical. Today's mining engineer has at his disposal the most powerful design and analytical aid ever, the microcomputer. There is, unfortunately, limited software for the study of hoisting systems, unlike that for other materials handling equipment (Manula and Albert, 1980; Prelaz et al., 1964; Bucklen, 1969; Thompson, 1985). HOIST reduces a time-consuming set of calculations to a concise package of interrelated subprograms. A literature review revealed no common-user programs to analyze hoisting systems, although at least four major hoist designers/manufacturers/installers have their own in-house programs. To provide a tool with which the mining engineer could preliminarily analyze a materials hoisting system or could check the calculations of a hoist contractor, a computer program was developed. HOIST was written in BASIC for the IBM-PC for ease of program adaptation and to encourage field use on compatible systems. Details of program development are omitted, since the basic principles of hoisting analyses are relatively straightforward, simple, and readily accepted (Harmon, 1973; Nordberg, n.d.; Adler, 1957). Program features, intended usage, and benefits of the computerized solution are emphasized over theory development and mathematical rigor. Background The mine hoist system that is selected and installed at a mine is the "lifeline" of that mine, with installations lasting 20 years or more. Thorough study is warranted to ensure that productivity demands are met at a minimum cost per ton. The increased cost of a large, powerful, high-speed hoist must be offset by increased production to justify its selection. To optimize this tradeoff, an extensive hoisting analysis should be performed. The analyses to properly size the skip (or cage), the drum, and the hoist drive are conducive to computerization, permitting rapid evaluation of changeable operating and design parameters, such as velocity, acceleration, state of balance, and productivity demand. The program is particularly useful in conducting sensitivity trials, such as investigation into the effect of change of productivity on skip capacity and on horsepower of the hoist drive. HOIST is currently limited to the study of drum-type hoists with cylindrical drum(s). However, only minor changes to the program would permit analysis of friction hoists and conical drum configurations. Model development and testing The program is based on accepted equations and physical relationships. Examples of manual calculations formed the basis for decision points and program branching. Data is input in the order that it would be needed if the problems were solved manually. The choices are arranged likewise. HOIST was developed in sections, with manual solutions performed to check program logic. The testing became more rigorous as sections were completed. Output from one section becomes input for following sections, as appropriate. The simplified flow diagram of HOIST is given in Fig. 1.

Jan 2, 1987

By V. T. McLemore

Deposits of rare earth elements (REE) are found in NM, but they have not been important exploration targets in past years because demand has been met elsewhere. However, with the projected increase in demand and potential lack of available production from China, the New Mexico deposits are being re-examined for their potential. REE-Th-U veins are found in the Gallinas, Caballo, Capitan, and Cornudas Mountains and Laughlin Peak-Chico Hills. Past production of bastnaesite has come from the Gallinas Mountains. Carbonatites are found in the Lemitar and Chupadera Mountains, Laughlin Peak-Chico Hills, Lobo Hill, and Monte Largo (Sandia Mountains). Although carbonatites have not been found in the Gallinas Mountains, they are suspected to occur in the subsurface based upon mineralogy/alteration. Disseminated Y-Zr deposits in syenite are found at Pajarito Mountain, Mescalero Apache Indian Reservation near Ruidoso. In 1990, Molycorp, Inc. reported historic resources of 2.7 million short tons grading 0.18% Y2O3 and 1.2% ZrO2 as disseminated eudialyte. Two additional deposit types have potential for REE in New Mexico: Cretaceous heavy mineral, beach-placer sandstone deposits and pegmatites. Exploration is ongoing in the Lemitar, Gallinas, and Cornudas Mountains.

Jan 1, 2012

By Daryl R. Tweeton

The Bureau of Mines measured the geochemical changes as H2S04 was used for in situ uranium leaching by Rocky Mountain Energy Company near Casper, Wyoming. Cores and ground water were analyzed before leaching. Water samples were taken from observation wells located between injection and production wells as the leach solution was brought up to full strength in several steps. Measurements were made of pH, Eh, temperature, conductivity, total dissolved solids, dissolved oxygen, HC03, U, V, Na, K, Ca, Mg, SO4, C1, Mo, Mn, Fe, Al, Si, F, P, As, and Se. The data were gathered to assist in geochemical modeling of leaching and to study the potential environmental effects of acid leaching. Environmental considerations appear favorable. For example, the concentration of Se, a toxic element often found in uranium deposits, stayed below the EPA standard for drinking water.

Jan 1, 1979

By Nathaniel Arbiter

A fully-instrumented driving mechanism has been constructed to study the power, aerating and solid suspension characteristics of several laboratory flotation machines. Machines operating over normal flotation speed ranges give constant power numbers in liquid' systems indicating that they operate under fully baffled turbulent flow conditions. Owing to lack of geometrical scaling, power numbers for different sizes of cells of the same make are different. Even larger differences occur between cells of different manufactures. For a given impeller, varying the tank size did not significantly affect the power consumption. Tank geometry and baffling has a slight effect on power consumption with shrouded impellers. For a given impeller speed, suspension height decreases while power increases with increasing mass of solids in suspension. While power consumption is hardly affected by particle size and clearance between the impeller and tank bottom, the suspension height significantly increases as clearance increases and as particle size decreases. Aeration was found to affect not only power but also the suspension characteristics of the machine. For closely sized particles drastic sedimentation occurred when a critical value of the air flow number was exceeded. The critical air flow number decreased with increasing particle size. This effect was less marked with a wide particle size range. The self-aerating capacity of flotation machines increases with cell size at a given speed for the same impeller-shroud system, but decreases in the presence of frother and solids. Equations have been established for correlating all of the studied variables. Data taken from the literature were also correlated with these equations.

Jan 1, 1968

By M. Hamarat

Freeport-McMoRan Copper & Gold (FCX) is committed to preserving and enhancing biodiversity in the areas in which we operate. As a member of the ICMM, FCX is committed to implement the 10 Sustainable Development (SD) Principles throughout our business. FCX is also a member of the Wildlife Habitat Council (WHC), a nonprofit coalition dedicated to protecting and enhancing wildl ife habitat. In alignment with ICMM SD Principle 7 and our Environmental Policy, FCX has set a performance goal to prepare a biodiversity inventory in 2010 and land management plan by end of 2011 for all active mining sites. In 2010 FCX established a Biodiversity Task Force to assist sites in biodiversity management; optimize use of resources around the globe; implement FCX goals and targets; and align biodiversity programs with ICMM principles and guidance. The task force consists of Environment and SD Department management, scientists and engineers from FCX sites, and WHC staff. The Task Force recently issued a biodiversity inventory guidance document to set expectations and provide consistency across the sites when developing a biodiversity inventory and land management plan.

Jan 1, 2011

By S. K. Kawatra

In many mining operations, particularly northern open-pit mines, large seasonal variations in grinding slurry temperature can occur. It is shown in this paper that this temperature shift can cause a winter-time loss in autogenous grinding efficiency of as much as 20Y. if it is not controlled. Laboratory experimentation indicates that much of this effect is due to increases in slurry viscosity as the temperature is decreased. An additional effect may result from changes in rock strength upon freezing, for which possible mechanisms are discussed. However, no effect clearly resulting from rock strength changes has been definitely confirmed.

Jan 1, 1990

By D. Nutakor

Rock joint stiffness is not only a poorly known parameter, but also has no established laboratory measurement procedure. This paper presents methods used to determine the normal and shear stiffnesses of healed joints filled with vapor-altered minerals obtained from the Yucca Mountain site in Nevada. Results show that these joints behave linearly up to 85% of their loading history and are stiff with strengths very close to the strength of the intact rock. Factors that might have contributed to the linear behavior of these joints are discussed and areas requiring further investigation are provided. Joint normal stiffness ranges from 7.16 to 64.77 GPa/mm with an average value of 26.93 GPa/mm, while joint shear stiffness averages 11.41 GPa/mm and ranges from 3.09 to 28.41 GPa/mm. Young?s modulus of the vapor-altered joint infilling was calculated from the stiffness of the healed joint. Young?s modulus of the vapor-altered joint filling material averages 7.89 GPa and ranges from 2.15 to 19.43 GPa. Given the pervasive presence of such altered rock, usually in the form of sub-spheroidal 3-D pockets, this property should be of value in any numerical modeling attempting to describe the mechanical behavior of these tuff formations at the level of detail where inclusions might be a factor.

Jan 1, 2008

"The paper treats the spatial aspect of mine sequence optimization. This aspect is revealed in the context of determination of the optimum number of cutbacks of an open pit mine. Cutback mining is a dominating method currently in base\precious metal mining and it is based on a pseudo-economic discretization of the pit space by using advanced pit design algorithms. The result of the implementation of such approach of pit design is the generation of pit shells, which need to be grouped into an optimum number of cutbacks for maximization of the project value. A mathematical solution of this problem is developed with the utilization of a combinatorial analysis. The solution provides a multi-variant investigation of the optimum mine sequence with the implementation of an author’s method for production scheduling optimization, which uses the Net Present Value as a criterion for assessing the economic efficiency of mine sequencing. A case study is provided for the conditions of a hypothetical open pit gold mine to illustrate the applicability of the approach. The results obtained reveal the complex nature of the variation of the Net Present Value as a function of the cutback geometry. INTRODUCTION The mine sequence optimization in open pit mining is a procedure that predetermines the efficiency of the production scheduling optimization. From a technological standpoint, the mine sequence optimization deals with two aspects – spatial and time. Each of them plays a tremendously important role in searching for the optimum solution of the open pit design problem. Original results on the time aspect of mine sequence optimization are published by Halatchev [2002]. They reveal a wide range of the Net Present Value (NPV) variation for a multi-variant arrangement of mine sequence over time and using a fixed geometry of the cutbacks, which determines the economic potential of a single open pit mine from a deterministic standpoint. The results show a range of NPV variation up to 30% depending on the stripping ratio of the mine. The effect of this variation is mainly due to the implementation of the mine planning principle of waste deferment in the scheduling optimization and using all theoretically possible variants of mine sequence arrangement by the inclusion of the bench sequences over the Life-Of-Mine (LOM) in the production process."

Jan 1, 2015

By Michael Roach

"There’s a bit of confusion and misinformation in the tunneling and underground construction industry regarding contractor joint ventures. If it was all so clear I would not have been "asked" to write this article. For those of us on the contractors’ side of the fence, joint venture business relationships have been a part of life for a long time. But even for contractors, there can be a bit of confusion, and it normally begins on bid day.How often have you received bid results and wondered (out loud, usually), "Who the hell are the Lake Mead Intake Constructors"? or the "Regional Connector Constructors"? Once you get past the name, you see that there is nothing behind Oz’s curtain other than a couple of contractors bidding and building work in an attempt to make a profit. So take a few minutes to read the rest of this, and I’ll do my best to dispel a few mythWhat is a joint venture?In some form or fashion, joint ventures are as old as industry itself. In the United States, some of the earliest (and largest) joint ventures involved the railroads and oil companies in the late 1800s. In the United States’ underground construction industry, joint venture names such as, Healy-Greenfield, Green and Winston, Gates & Fox and Walsh, Shea-Ball, Kenny-Paschen and S&M-Traylor bring back memories of successful joint ventures that operated over many projects.There are nearly as many definitions for joint ventures (JVs) as there are attorneys. A short and simple definition is, "an association of two or more companies engaged in a singular, for-profit business enterprise without actual partnership or incorporation." That’s it. Two or more contractors decide to partner up for one or more projects. One benefit of the JV relationship is that the partners typically do not need to file incorporation documents, or articles of organization within the state where they intend to operate. So it is a relatively easy business arrangement to pull together. Other benefits of the JV arrangement include: • Oportunities to gain new expertise and capacity.• The ability for firms to move into new geographic markets.• JV agreements are not long-term commitments.• Sharing of financial support for a project.• Sharing of financial risks within a project. between the partners.• Can complicate dispute resolutions with the owner and between partners"

Jan 1, 2014

By R. E. Mitchell

Environmental Impact Assessment (EIA) is the accepted method for evaluating proposed mining and other industrial projects to obtain regulatory approval and to help companies plan for responsible development. Another evaluation system becoming increasingly more common for proposed projects is the Environmental, Social and Health Impact Assessment (ESHIA). An ESHIA differs from an EIA for its more comprehensive and inclusive approach to evaluate potential impacts on public health, and its ecosystem services approach to assessing biodiversity impacts. An ESHIA may also be required by certain lenders for financing major projects. Conducting an ESHIA for a proposed mining development is not without its challenges, with costs, scheduling, regulatory concordance and other constraints to be considered. This paper examines some benefits and challenges of ESHIAs and summarizes lessons learned using a case study approach.

Jan 1, 2012

Introduction Some people say it is almost impossible to get mining permits in California. Some say the day of the lone mining entrepreneur is past. And some say you cannot make money mining gold where old-timers have already mined it, especially in Tertiary gravels. But a young mining operator and SME member, Tim Callaway, is proving these ideas wrong. Callaway's company, Brush Creek Mining and Development Inc., has the necessary permits for its Gardner's Point gold mine in Sierra County, CA. And, Callaway has secured funds for the 7.7 km'/d (10,000 cypd) Tertiary gravel operation. The company's initial goal is to produce 373 to 466 kg/a (12,000 to 15,000 oz per year) of gold at Gardner's Point mine at a cost of less than $6.43/g ($200 per oz). Feasibility studies are currently being conducted to consider product levels up to the 1555 kg/a (50,000 oz per year) involving additional plants and infrastructure. While exploring for other hard-rock properties, the Brush Creek company already operates the Brush Creek lode gold mine. The mine sits high on a ridge south of Goodyear's Bar, which is located on the North Yuba river. It might be noted that the Brush Creek mine has been the subject of media stories recounting how a mine can operate with sensitivity to the environment. Gardner's Point project In 1983, Callaway negotiated with the Gardners Point Ltd. Partnership for control of the Gardner's Point property. The Partnership had been engaged for three years in securing permits, mapping and drilling, and test mining. The Partnership actually mined about 43.5 dam3 (57,000 cu yd) of gravel, which yielded 25.2 kg (810 oz) of free gold. Later, the Brush Creek company acquired ownership of the property. The company then began its own exploration and development program. As underground development proceeded at the Brush Creek mine, plans matured for a high-volume operation at Gardner's Point. Australian and English investors contacted Callaway. A joint venture was negotiated. The Australian owners became majority participants; the Brush Creek company, a minority participant and the operator. The Australian investors agreed to contribute $3.5 million (60%) to the Brush Creek Joint Ventures. The Brush Creek company will contribute its expertise as well as assets and liabilities valued at $2.3 million (40%). About $2 million has been allocated to the Gardner's Point project. Later, Brush Creek Mining and Development Inc. sold 50.4% of the company's common stock to English investors for $5.4 million. Callaway negotiated this private placement, which permits further exploration of projects being investigated. Geography and history The Gardner's Point mine is located in the northern Sierra Nevada of California, about 9.6 km (6 miles) east of the little town of La Porte in Plumas County. The mine lies high on a ridge above Slate Creek, which divides Plumas and Sierra Counties. La Porte is accessible from the Sacramento area by a winding, paved, two-lane highway. But the mine is reached only by two different unpaved county and Forest Service roads. Both roads include steep grades in and out of the Slate Creek canyon. Mine elevation is about 1.4 km (4600 ft) above sea level. The area is thus threatened by occasional heavy winter snows, though it

Jan 3, 1987

By Charles W. Daugherty, James P. Gould, Kenneth R. Ware

INTRODUCTION As illustrated in Figure 1, the Washington Metropolitan Area Transit Authority's (WMATA) rapid transit system (METRO) ultimately will comprise 100 miles of line divided among 10 routes. At this time about 46 per cent of the system is under construction or in operation. Planning and design of an additional 38 per cent is at an advanced stage. Of the 84 miles under development or construction, about 10.4 miles consist of soft ground tunnels, and another 1600 feet of mixed face. This paper describes most of the factors considered by designers in setting grades for such tunnels. It is hoped the paper will be a useful guide to planners and engineers in developing similar transit systems. The problems faced in Washington, including those related to geology, are not so unique that the solutions cannot be applied to other systems. The paper also may be of interest to contractors who have not perceived the logic behind the selection of a particular vertical alignment. An attempt is made to explain the background constraints that make most tunnel alignments a compromise among competing alternatives. Readers might assume that the choice of alignments is largely controlled by geological conditions. In fact this is merely one of many factors to be considered.

Jan 1, 1976

By Lawrence H. Roth

Past failures of coal refuse embankments have resulted in intensified efforts in inspections of coal refuse sites by the Mining. Enforcement, and Safety Administration (MESA). MESA inspections however, are mainly qualitative and are often time consuming, Therefore, in August 1975 CH2M HILL was awarded a contract to identify, develop, and test a rapid system for monitoring coal refuse embankments to aid in MESA inspections. The rapid monitoring system developed uses convergent and vertical photography from conventional fixed-wing aircraft. The system was tested on an active landslide and on two coal refuse facilities using both black and white and color infrared film. Field tests showed the system was capable of accurate measurement while providing qualitative data through photo interpretation. The accuracy of the system allows it to be used to monitor coal refuse embankments, tailings dams, major earth dams, and natural slopes. Based on CH2M HILL results cost for monitoring by rapid system was approximately 25 percent of cost by conventional ground survey.

Jan 1, 1980

By P. D. Rao

Although phosphorus is a very important biogenic element, its concentration in coal is generally low. Phosphorus concentrations typically range from 0.001 % to 0.229% in raw coals of the contiguous 48 states. Some Alaskan coals in the Cook Inlet region contain horizons unusually high in phosphorus. A foot by foot analysis of deep drill core, containing 70 ft. of sub bituminous 'C' coal from the Beluga coal field, Alaska, showed certain increments contained as high as 17.03% P2O5 in the coal ash; 1.01 % P on a moisture-free coal basis. Crandallite has been identified by electron microprobe analyses as a phosphorus numeral in these coals. The authors could quantify calcium, barium, strontium and phosphorus concentrations from the coal attributable to crandallite. These high phosphorus coals provided a unique opportunity to study the association of phosphorus in coals using chemical fractionation for exchangeable cations and acid extractable elements. Since the source of high phosphorous horizons in Cook Inlet coals is attributed to volcanic ash, it is suggested that the profiles of acid extractable phosphorous concentration may be useful for coal seam correlations.

Jan 1, 1992

By Kenneth R. Krivanek

In recent years the widespread problems of air and water pollution generated by both population and industrial expansion have become a major public concern. Therefore, many municipalities are striving to achieve more efficient wastewater treatment processes so these wastewater's can be reintroduced into the waterways of our nation with little or no detrimental effects on the future beneficial use of that water. With this, improved treatment comes an ever increasing volume of wastewater sludge which must be disposed of in a manner of minimal impact on the environment. Furthermore, with demand for energy continually accelerating in this nation, our concern over high oil prices and our increasing dependency on foreign oil sources, there has been an ever growing interest in the largest energy source that are nation has, coal. However, surface mining of coal can cause many environmental problems when adequate precautions are not faithfully adhered to. These problems include water pollution from silt and/or clay erosion and acid runoff, produced by oxidation and hydrolysis of pyrite; i.e., FeS2 + 3/02 + H20 + FeSO4 + H2SO4. One method of wastewater sludge disposal which can utilize large volumes of sludge for a beneficial project that may not compound our environmental problems is spray irrigation, to either depleted farmland or to abandoned strip-mined soils. Sludge is characteristically high in organics, as well as having near neutral to alkaline pH properties. With these two qualities it possesses a potential for neutralizing acid strip mine spoils, which would enhance the establishment of a vegetative ground cover. Sludge can accomplish this by lowering the oxidation potential, reducing the solubility of iron and aluminum and by the chelation of metals, thereby

Jan 1, 1977