Search Documents

By Sun Guangzhong, Liang Jinhuo

Adverse geological condition is a major factor which makes construction difficulty in tunneling. But if it is predicted and tunnel support is made efficiently in time, the above difficulty can be reduced. It is necessary to develop one or several effective and economical geological methods for prediction of tunnel geology while expensive and time-consuming instruments are used. This paper reviews and proposes several geological methods for prediction of fault, seam, contact zone, and groundwater inrush. These methods have been proved to be effective and economical in tunneling practice in China.

Jan 1, 1987

By Ivo Dreiseitl, Kondratenko. Anatoly

"The second prime area within the Interoceanmetal Joint Organization exploration area named H22 was delineated in 2013 with the goal to ensure sufficient nodule reserves for profitable mining operations and processing.The knowledge base for area H22 has been obtained from archive materials. The geological situation can be characterized as follows: the sea bottom is represented by tectonic blocks oriented in a sub-meridional direction. According to swath mapping, the depressions (troughs) are contoured at depths of 4500-4600 m while the tops of horsts occur at 4300-4350 m. Volcanic relief occupies 6% of the H22 area; in the eastern part a multicone volcano was detected. Its area at the base is 153 km2. The maximum height of a cone above the base is 850 m. The crystalline basement composed by tholeiitic basalts of late Oligocene age is covered by about 100 m of sediments. Semi-consolidated to consolidated calcareous nanofossil sediments of the Marquesas formation are deposited on the basement. Higher up in the profile sediments of the Clipperton formation occur. They are represented by unconsolidated siliceous (Radiolaria, Diatom) ooze. Sediments containing calcium carbonate have not been detected. Where opaline silica (or CaCO3 if any) content is below 5%, the sediments belong to zeolitic clays or red pelagic clays. Grain size composition of the seabed and the near-seabed sediments in H22 classifies them into clayey silts."

Sep 1, 2014

By M. Moagabo

CO2 emissions from carbonate laden reclaimed mine spoil has been shown to pose a hazard to residents in homes built on or adjacent to such land. The objective of this project was to develop a soil CO2 flux survey protocol for assessing reclaimed mine land. The research involved CO2 chamber accumulation flux surveys; stable carbon isotope ratio analysis; statistical hypothesis testing to examine correlation between CO2 flux and soil temperature and moisture as well as spatial dependence; and geostatistics to map CO2 and delineate high flux zones. Soil temperature was observed to have a positive correlation with fluxes while soil moisture was observed to be negatively correlated. Spatial dependence of CO2 fluxes on reclaimed mine land was observed on one of the two study sites. The research suggests that macro-porosity and gas permeability may be important factors that explain CO2 migration in mine spoil. A flux survey protocol has been developed, based on these results, for reclaimed mine lands. The work demonstrates the capability of geostatistical methods to delineate high flux fields. Further research will be required to determine suitable thresholds for such analysis.

Jan 1, 2012

By Henning R. Norbom

Lime has been produced for many centuries. The simple pot kiln was one of the first devices used in this process. It was constructed of stone often on the side of a hill to reduce construction efforts and provide easy access to the top for feeding of limestone. It was fired from below with wood and coal. The pot kiln was very small and operated on the batch principle. The kiln being cooled between each batch, the fuel consumption was horrendous. The lime quality was poor with perhaps only one half of a batch being lime of suitable quality. Of the remaining half one part would be over burned and another part underburned. For centuries the lime burning technique was improved at a barely recognizable rate. One of the first major steps forward was the introduction of the continuous process vertical lime kiln. Although at first crudely constructed, the kiln had a refractory lining. It was charged with alternate layers of limestone and solid fuel usually in the form of coke. Continuous mode of operation, larger unit size and better heat distribution resulted in greatly improved fuel economy. However, quality of lime produced still left much to be desired. One problem was contamination by ashes from solid fuel.

Jan 1, 1978

By C. V. Baltzer, E. L. J. Bingham

Compliance with the EPA's emerging Clean Water Act regulations can be challenging. Open pit copper mines in Arizona have found themselves in a tangled web of changing rules, regulations, and guidance documents regarding storm water and process water discharges. Large mining properties must come up to speed on a myriad of issues including the definition of zero discharge, what constitutes a process related spring or seep, and tailings and waste rock Best Management Practices. The example of the Pinto Valley Mine in Arizona is used to illustrate National Pollution Discharge Elimination System regulatory issues.

Jan 1, 2001

By John A. Cherry

Groundwater monitoring conducted at an acidic uranium-tailings impoundment in Wyoming and at one in Ontario indicate that at these unlined impoundments situated on unconfined sand aquifers, there exist well-developed plumes of contaminated groundwater. In the literature similar results are reported for three other unconfined aquifers at mill sites in Wyoming. The plumes extend for distances of several hundred to a few thousand metres from the impoundments. They have a zone of low pH beneath and adjacent to the impoundments and a larger zone of near-neutral pH that extends to the outer limits of the plume. The low-pH zones are generally small compared to the neutral-pH zones because the advance rate of the fronts of acidic tailings-derived water is slower than the average velocity of groundwater which controls the advance of the high pH zone. The retardation of the acid fronts is a result of geochemical reactions that cause hydrogen-ion consumption in a slowly-advancing neutralization zone. Within each of the plumes, the low-pH zone has high concentrations of transition metals, heavy metals and radionuclides. In the neutral-pH zones all of the metals and radionuclides occur at significantly lower concentrations and are generally at levels much below those specified in national drinking water standards. An exception at two of the Wyoming sites is uranium, which exists at levels close to the drinking water limit. A second exception is ferrous iron at the Ontario site, which occurs at high concentrations throughout most of the plume. The carbonate alkalinity at this site is much lower than at the Wyoming sites. The field data indicate that even in very permeable aquifers with a low content of silt and clay, there is normally a considerable capacity for acid-front retardation. To take advantage of this capacity to control contaminant movement in the design, operation and decommissioning of tailings impoundments, it is necessary to be able to predict the rate of acid-front movement. This predictive task has two primary components. The first is to identify the important flow paths from the tailings through the groundwater system and the second is to determine the degree of acid-front retardation that will occur as the tailings-derived water moves along these flow paths. Relative to these two tasks determination of the effects of hydrodynamic dispersion is generally of lesser importance and simple approximations that do not involve field or laboratory tests are probably adequate. In order to effectively apply the acid neutralization concept to the prediction of subsurface contaminant migration at uranium-mill tailings, improved representations of hydrogeochemical behavior of iron and aluminum in the neutralization zone and of the consumption of hydrogen ions through reactions with carbonate and aluminum-silicate minerals are required. Along with the hydrogen ions contained in the tailings water the ferrous iron represents a large potential source of acid but the extent to which ferrous iron converts to ferric iron to produce acid is problematic. Detailed hydrogeochemical evaluation of existing contaminant plumes and the performance of laboratory experiments under appropriate redox conditions ore prerequisites for the improvement of predictive models. However, the existing field and laboratory data provide a basis for preliminary predictions of contaminant migration from acidic uranium tailings impoundments.

Jan 1, 1982

By John C. Bowling

Many recent mine developments in North America are located in remote northern regions with extreme winter temperatures in the range of -20oF to -60°F. In addition, many locations are subject to very heavy snowfall. This paper discusses some of the key considerations in the planning and design of mine plant buildings, particularly concentrators, located in these regions. SUMMARY & CONCLUSIONS The subject is considered under three main headings: I. Building Out line and Structural Frame 2. Wall and Roof Materials 3. Foundations The plan outline of a mine plant building will naturally be governed by the scope and layout of the process equipment it contains. The selection of roof profile, on the other hand, will generally depend upon a number of factors extraneous to the process e.g. snow conditions. When these factors are considered for concentrators in cold locations, a flat or stepped roof will usually be more economical and suitable than a sloping roof. The materials normally used for the structural framework of concentrators are the same as used for other industrial buildings, namely steel, concrete and wood. Structural steel, however, is the most commonly used material for concentrators in

Jan 1, 1971

By Edwin W. Tooker

Creation of needed new resources will be accomplished mainly by imaginative and diligent geologic exploration because geologic availability is the key determinant of future mineral supply. Adequate resources of most commodities can be made available for the rest of this century and beyond if they are discovered. Thus conversion of hypothetical and speculative resources into available reserves will provide the principal challenge to earth scientists. Additional problems now compete for our attention. First is a challenge to discover more resources than have been found to date for domestic needs as world-wide demands increase exponentially and as easily found high-grade deposits are rapidly being depleted. New ways to find new types of deposits are required. Second, the United States, a resource importer, increasingly is challenged for access to foreign supplies through stiffening competition and economic or expropriation sanctions. Balancing needs for mineral supply and environmental protection is a third challenge. Geologic explorers must consider statutory as well as economic and technologic requirements, controlled access to public and private lands, competition with urban sprawl or wilderness, limitations on discovery, appraisal and mining methods, and restoration of mined areas. Finally, is the challenge to temper public and private attitudes and assure that decisions bearing on resource problems are based on comprehensive credible facts. While striving to maintain and improve the standard of living, many Americans appear to disdain and mistrust those organizations that provide their material where-withal. Meeting these challenges effectively, and in time, will require careful appraisal of the resource system and the joint efforts of industry, university, and government earth science research.

Jan 1, 1974

By VIVEK KASHYAP, Evody Tshijik Karumb, PATRICK TAYLOR

The partial reduction of zinc ferrite to zinc oxide and iron (II, III) oxide can enhance the leaching rate of zinc. Zinc ferrite has often been found as a major component of zinc residues and electric arc furnace dust. The Waelz process is an existing process for zinc ferrite processing, which requires a temperature of more than about 1200 °C to produce Waelz oxide containing ZnO. Since zinc residues have been deemed as a potential way for the extraction of zinc and other critical metals, it is important to analyze the reaction kinetics in the temperature range of interest. This manuscript discusses the chemical kinetics of zinc ferrite reduction by hydrogen gas. Several researchers studied the reduction of zinc ferrite with CO; however, unlike CO, the use of H2 gas as a reductant allows partial reduction of zinc ferrite even at low-temperature range (400–600 °C). Thermogravimetric analyses (TGA) experiments were performed in the temperature range of 300–700 °C with 10% and 30% H2, and the data obtained was analyzed using the isoconversional method of kinetic analyses. The standard models used for isoconversional kinetic analysis were chosen from literature and experimental data were fitted to determine the controlling mechanism and calculation of kinetic parameters of reduction of zinc ferrite. The rate of reaction was found to be increasing with an increase in temperature and partial pressure of H2 gas. The reaction could be divided into three stages, where reaction interface contraction was found to be the controlling mechanism at the initial stage of reaction. As the reaction proceeds, product layer thickness increases, and thus, diffusion was found to be the controlling mechanism. Roasting products obtained from TGA experiments were also characterized using a scanning electron microscope (SEM) to verify critical morphological details.

Jul 26, 2022

By T. E. Wayland

Bentonites are clay materials composed principally of minerals in the montmorillonite group. Distinctive physical properties of the montmorillonite minerals are responsible for selected bentonite deposits having become the raw materials source of industrial clay products which are virtually essential to the maintenance of high production standards in the petroleum, foundry, taconite and other basic industries. These versatile materials have no suitable substitutes in either their major applications or in hundreds of speciality products, The economics of the bentonite mining industry follows closely the established pattern of other non-metallic raw materials. Aggressive competition, advanced technologies, progressive marketing techniques, substantial reserves, and vast unmeasured resources insure the continued supply of high quality bentonite to industry at bargain prices. The purpose of this paper is to discuss the geology and economics of bentonite deposits, summarize both major domestic mining districts and foreign deposits, and report significant results of research and development.

Jan 1, 1970

By Matthew Wallin

A part of the East Bay Municipal Utility District?s Folsom South Canal Connection Project, 430 feet of raw water pipe was installed using micro tunneling beneath the Mokelumne River. The access shafts for this crossing were constructed 50 and 35 feet deep through very dense sands and soft sandstone and siltstone. High groundwater and the immediate source of recharge from the river required watertight shaft construction methods. The shaft contractor, Drill Tech of Antioch, CA, used a brand new Bauer cutter-soil mixing (CSM) rig to construct the large shafts. The structural concept is similar to secant piles, but instead of creating cylinders of soilcrete, the CSM rig creates interlocking rectangular panels. This technology has been used previously in Europe, Asia, and Canada, but this was the first project to use CSM technology in the United States. Cutter-soil mixing technology has other applications beyond shaft construction, including retaining wall construction and levee reinforcement.

By VÍCTOR VÁZQUEZ-VÁZQUEZ, GUILLERMO TIBURCIO-MUNIVE, María M. Salazar-Campoy, JESÚS L. VALENZUELA-GARCÍA, OFELIA HERNÁNDEZ-NEGRETE

The present study examined a process for precious metal recovery (silver and gold) from difficult minerals which exhibit refractory characteristics to cyanidation and ammonium thiosulfate leaching (low extraction and high consumption of leaching agent). It is well known that mangano-argentiferous minerals are mainly composed of manganese, silver, gold, and iron. In this research, a mineral sample from Monte del Favor mine, located in Hostotipaquillo, Jalisco, Mexico, was physically and chemically characterized by X-ray powder diffraction (XRPD), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), fire assay, and atomic absorption spectroscopy (AAS). Two-stage leaching was carried out: first to eliminate manganese from the sample using sodium sulfite (Na2SO3) as a reductive reagent and sulfuric acid (H2SO4) and a second stage to dissolve silver and gold with sodium hypochlorite (NaClO) and hydrochloric acid (HCl); the results show extraction around 96% for Mn and 98.73% and 83%of Ag and Au, respectively. The usefulness of high acidity and Na2SO3 to obtain good results in Mn and Ag leaching is discussed along with the roles that HCl and NaClO play in the dissolution of Ag and Au values.

Apr 15, 2020

By K. A. Lewandowski

Leach heaps are plagued with problems due to fine material migrating downwards, clogging the spaces between the coarser ore particles, resulting in decreased metal recovery rates. The use of a binder in agglomeration would allow the fine material to be immobilized, increasing the availability for the solution to come in contact with all the ore. As much as 1.64*1012 BTU per year would be able to be saved if a 25% increase in copper recovery was experienced, assuming that 70% of heap leaching units converted to using agglomeration technology. This is equivalent to approximately 18% of the energy currently being used in leaching heaps.

Jan 1, 2008

By N. Dhawan

With ever-increasing demand, low-grade complex ores and strict environmental regulations, metallurgical processing options have become limited. Heap leach technology provides several benefits to combat these issues including low cost, flexibility and diversified process conditions. This paper provides an overview of heap leaching technology with specific emphasis on chemical aspects. Hence, influencing factors, advantages and disadvantages, testing approaches and some fundamentals will be discussed. Finally, heap leach technology for different ore types (copper, nickel, uranium and gold) will be briefly compared.

Jan 1, 2012

By Charles L. Allie

Since Reserve Mining Co. began commercial operations at Silver Bay, MN, some 25 years ago, major improvements in taconite processing technology have become available. In addition, significant new government standards have been imposed on industrial operations. By implementing a $370-million modernization program, Reserve was able to accomplish two major company objectives: the quality of concentrates produced from the Peter Mitchell mine has improved, and the operation meets both present and foreseeable environmental standards. Process modifications at Reserve were designed to: •Reduce the pellet silica content from 9% to 5%; •Increase the pellet iron content from 62.5% to 65.8%; •Implement a tailings disposal system utilizing "best available technology" water quality controls; and •Reduce air emissions by installing "best available technology" air emission controls. By adding dry cobbing, fine screening, and flotation to the concentrating process, pellet silica content has been reduced; the process reclaims and reuses all process waters; all tailings are stored in a zero discharge tailings basin; and all air emission standards are being met. Initial Beneficiation at Silver Bay Reserve's Peter Mitchell mine at Babbitt, MN, is on the eastern end of the Biwabik iron formation. The open-pit mine is approximately 16 km long, 0.8 km wide, and presently has a maximum depth of about 50 m. Principal constituents of the ore body are magnetite, quartz, and iron-magnesium silicates. The company's large commercial plant began operating at Silver Bay, 75 rail km from the mine, in 1955. Facilities have historically had the capacity to process 31.5 Mt/a of taconite, containing an average 24% magnetic iron, into 11 Mt/a of iron ore pellets. Reserve's initial beneficiation process-which existed up to early 1979-consisted of two crushing stages at the Babbitt mine site, two additional crushing and screening stages at Silver Bay, grinding in a conventional rod-ball¬regrind mill circuit, size classification with cyclones, and concentration with magnetic and hydraulic separators. Concentrate produced by that circuit assayed 65% iron and 8.5% silica, with a screen analysis of 94% -44 µm, and a surface area of 9300 cm2/cm3. Pellets produced from this concentrate assayed 62.5% iron and 9% silica (dry basis). Construction began in 1977 to modify Reserve's operation. Process modifications were designed from pilot scale operations that had been operated and researched by Reserve for more than 10 years. There were two design restraints imposed on the process: economic constraints that Reserve continue to use much of the existing processes and structures in the new operation; and a substantial number of government-imposed permit constraints. In effect, the tailings process was designed first and then a concentrating process was developed that would "fit" the tailings disposal system. Operation of the modified process began in June 1980. Crushing Remains Unchanged No changes in process flow were made at either the Babbitt mine and crushing plant or at the Silver Bay fine crusher. Gyratory crushers reduce run-of-mine taconite to -90 mm-diam at the mine. Taconite is then transported to Silver Bay by intra-plant railroad. There are 10 fine crushing lines. Each consists of a double deck screen, followed by a heavy duty short head crusher, a second double deck screen, and second short head crusher. All screen undersize material bypasses the crushing lines, resulting in an open circuit crushing process. Fine crusher product is approximately 98% - 20 mm, 80% -12 mm, and 50% -10 mm in diameter. Each fine crusher line processes about 400 t/h of crude taconite. Cobbing Provides Aggregate for Tailings Dams The first major process change was the addition of dry cobbing, a dry magnetic separation step between the fine crusher and concentrator. Dry cobbing serves two major purposes in the new process. Its principal function is to provide large volumes of dry coarse aggregate for use in construction of tailings dams. This process rejects about 20% of the fine crusher product as tailings with a size analysis of 98% -20 mm and 50% - 10 mm. These tailings are free draining and have high frictional shear strengths-two key requirements for dam building aggregates. Fine crusher product is conveyed to a new dry cobbing building. Here crushed ore is discharged into one of two 30-minute capacity surge bins. Crushed ore is withdrawn by 12 constant speed conveyor belts; each discharges 500 t of crushed taconite into a dry cobbing machine. Each machine consists of a 3-m-long riffle splitter and two vari-

Jan 12, 1980

By W. K. Hitchcock

Anecdotal evidence suggests that re-entering a sealed heating poses a significant hazard, whereby the original heating is rejuvenated at an accelerated rate forcing withdrawal and re-sealing of the area. Bulk-scale laboratory experiments using a two-metre column confirm these mine site observations. A high volatile bituminous coal from New South Wales, Australia was allowed to develop a significant hot spot before being inerted with nitrogen and allowed to cool. Air was then allowed back into the coal after the nitrogen was turned off and a hot spot developed almost immediately at the same location as the original hot spot before it quickly migrated towards the air source within a day. Two more re-entries were simulated. Each successive re-entry developed a broader hot spot and took longer to reach thermal runaway. These results clearly show the behaviour that can be expected when trying to recover a section of an underground coal mine that has been sealed due to a spontaneous combustion event.

Jan 1, 2009

By Roozbeh Afzali

Designing an appropriate tunnel blasting pattern reduces the cost of rock breakage and subsequent operations such as loading, haulage and support of tunnels. For that reason, we developed a software that designs tunnel blasting patterns. Using this software, three different tunnel blast design models based on parallel hole cut, namely, Swedish, Konya and Energy Balance, were investigated and compared for a virtual tunnel. Accordingly, blasting patterns were designed, for different cross sections. The trend of parameters such as specific charge and specific drilling as functions of tunnel cross-section was determined for each model. Our results show that, in general, The Swedish model gives lower specific charge and specific drilling compared to other models.

Jan 1, 2008

By J. Armstrong, J. Bourgeois, S. Warren

The application of statistical analysis software programs has proven useful for investigation of rockfall runout distance along a designed slope. Rockfall modeling programs are continually being upgraded with more sophisticated analysis tools, such as the use of the rigid body versus lump mass models. Engineers at mine sites utilizing the software may have varied experience related to these models, their associated input parameters, and how to interpret the generated results. To address this concern, researchers at the Spokane Mining Research Division (SMRD) of the U.S. National Institute for Occupational Safety and Health (NIOSH) investigated the influence of slope height, slope angle, slope material, and rock size for both rigid body and lump mass models in a 2-D statistical analysis program. Based on a literature search and industry input, specific ranges common to that of an open pit mining environment were chosen for each of the input parameters to determine 90% rock runout distance as well as their sensitivity to change. Data collected from this numerical analysis and simulation will be compared to empirical rockfall data gathered through the duration of the Highwall Safety project conducted by NIOSH from 2022–2026.

Mar 2, 2022

By Jafar Khademi Hamidi

The Zagros long tunnel is one of the main components of Sirvan water transfer project in western Iran. It is approximately 48 km in length and consisted of two lots. The second 26 km lot of this tunnel is under construction by a 6.73 m diameter double shield (DS) TBM. The tunnel passes through several formations with wide range rock mass qualities. During the tunnel alignment, changes in rock quality were highly frequent from poor to very good. The encountered geological conditions required TBM operation to change frequently from hard rock to soft, dry to flowing, sticky to nonsticky ground (and vice versa), more often than expected. In the course of tunneling, the machine has encountered nearly many adverse geologic conditions. The most important problems have been sudden high volume water inflow into the tunnel, sticky ground, and gas seepage, all of which resulted in reduced TBM advance rates. This study will high-light two difficult ground conditions including large water ingress and sticky ground and also the related problems encountered by the TBM along 8 km of excavated tunnel. In sticky grounds, cleaning of the clogged cutter head caused many delays and contributed to additional downtime. Application of some operational modifications, including decreased TBM thrust showed satisfactory results in such cases. While reduced thrust resulted in reduced penetration rate, but the overall TBM advance was greatly improved by the increase utilization rate and elimination of down time related to cleaning of the head. To cope with high water inflow, application of preventive measures such as pre-grouting has proved to be a more efficientsolution. The sealing of ground water inflow also decreased seepage of dangerous H2S gas and other chemicals such as hydrocarbons accompanying the groundwater.

By Dennis Molvik, Omar Fulton, Chris D. Breeds, Don Gonzales

This paper presents and describes the South Interceptor Parallel Phase III Contract C93012C, which involved construction of a nominal 2.7 m (9-ft) finished diameter sewer conveyance using both pipe jacking and conventional tunneling methods. Earth Pressure Balance (EPB) excavation was required to minimize the potential for settlement beneath a main rail line, overpass, sensitive wetland, areas of contaminated soils, and nearby structures. Ground conditions predicted in the Geotechnical Baseline Report included low plasticity, clayey silt (40 to 10%) and silty sand (60–90%) with pieces of wood such as logs, stumps, branches and other tree fragments. Soil cover ranged from 2.7 m (9-ft) to 5.4 m (18-ft) over the tunnel crown with a groundwater table between 1.5 m (5-ft) and 3.7 m (12-ft) deep.

Jan 1, 2003