Search Documents

By A. McGarr

The shear stress t that can be sustained by the rock mass in the environs of a mining-induced earthquake controls the near-fault peak ground velocity v of that event according to v=0.25(ß/G)t, where ß is the shear wave speed and G is the modulus of rigidity. To estimate t at mining depths, I review the results of four studies involving Witwatersrand tremors that relate to the bulk shear strength. The first and most general analysis uses the common assumptions that the seismogenic crust is pervasively faulted, has hydrostatic pore pressure before mining, and an extensional stress state that is close to failure. Mining operations reduce the pore pressure to zero within the mine and redistribute the stresses such that, in localized regions, the state of stress is again at the point of failure. Laboratory friction experiments can be used to estimate t in the zero-pore-pressure regime. Second, model calculations of states of stress in the vicinity of mining at about 3 km depth indicated the shear stress available to cause faulting near the centre of a distribution of induced earthquakes. Third, laboratory experiments combined with microscopic analyses of fault gouge from the rupture zone of a mining-induced event provided an estimate of the average shear stress acting on the fault to cause this earthquake at a depth of 2 km. Fourth, moment tensors determined for mining-induced earthquakes usually show substantial implosive components, from which it is straightforward to estimate t. These four different analyses yield estimates of t that fall in the range 30to 61 MPa which implies that near-fault particle velocities could be as high as about 1.5 m/s. To the extent that the causative fault ruptures previously intact rock, both t and v, in localized regions, could be several times higher than 61 MPa and 1.5 m/s.

Jan 1, 2002

By V. Bari?ic

The scheduled power cuts of early 2008 were a disturbing reminder that South Africa needs to expand its power-generating capacity. Low-grade and discard coals, of which South Africa has much, are a source of energy and amenable to combustion in circulating fluidized beds (CFBs). Foster Wheeler (FW) has a long record in developing this technology in boilers. The technology is flexible in burning a variety of fuels; low-grade, high-ash coals, good quality bituminous and anthracite coals, and biomass and waste fuels have all been used. CFB boilers are efficient, reliable and can be designed to meet tight emission standards. In recent years once-through supercritical (OTSC) CFB technology has been developed. It enables the next stage in CFB development to proceed to a medium-scale (500 MWe) utility in such projects as Lagisza, which runs at a net efficiency of nearly 44%. Scaling the technology up to 800 MWe with a net efficiency of>45% is planned to be commercial during 2009. CFB technology can reduce CO2 emissions in the repowering of coal-fired and greenfield power plants. It does so through greater efficiencies and by co-combusting coal with biomass. FW has also developed CFB technology for the gasification of biomass, as, for example, in a pressurized gasifier to produce syngas, which can be used for the production of biodiesel, thereby reducing CO2 emissions from vehicles. Carbon capture and storage (CCS) can potentially cut CO2 emissions in the generation of power from fossil fuels in the short term, provided that it gains public acceptance, that the required regulatory framework is created, and that emission-trading mechanisms or other incentives provide a solid return on the major investments required. Oxyfuel combustion is an option in CCS; Foster Wheeler is adapting its CFB combustion technology for oxy-fuel combustion to meet this challenge. It is developing Flexi-burn?, which enables a plant to be operated either with or without carbon capture. This paper describes the status of CFB technology in terms of boiler efficiency and fuel flexibility. It highlights the advantages of CFB technology for oxyfuel combustion, presents a development plan for Flexi-burn?, and discusses a pressurized gasifier for biodiesel applications.

Jan 1, 2009

By G. J. van Tonder

The use of Molecular Recognition Technology (MRT), a highly selective separation technology using specifically designed ligands (such as macrocycles), has been demonstrated to be an effective treatment process for removal of several ions that are commonly found in many hydrometallurgical circuits as well as in environ-mental treatment operations. Ions removed by MRT include base, heavy and transition metals, precious metals, halides, and alkali/alkaline earths. A MRT pilot plant run was conducted at Zincor to demonstrate the cobalt/nickel purification of zinc electrolyte, and to recover saleable pure cobalt/nickel sulphate solution. The MRT process holds various advantages, which include the elimination of a catalyst such as arsenic trioxide, conventionally used in cobalt and nickel cementation. SuperLig® 138 can be used to remove cobalt and nickel from120?170 g/l Zn-solutions at pH 1?2. The Zincor MRT application demonstrated its capability of concentrating large volumes o copper barren impure solution at low cobalt and nickel concentration levels in the feed, to small solution volumes at high cobalt and nickel concentrations. Around 99.5% of the cobalt was removed from solution with cobalt impurity levels in feed varying between 10 mg/l and 26 mg/l.

Jan 1, 2002

By P. Mogodi

The purpose of the project was to propose a coal clearance system (coal transportation system from the mining face to the plant) that could be used for the planned underground operations at Zondagsfontein Colliery. Components of the current coal clearance system were overlooked during feasibility studies. Subsequent studies of the coal clearance system revealed that the combined capacity of the two trunk belts does not match that of the shaft (main) belt. As a result production downtimes will be encountered due to bottlenecks in the system. Ways of addressing this challenge were analysed by weighing both advantages and disadvantages and ultimately a surge bin option was selected. Belt conveyor simulations were conducted in order to determine the optimum capacity of the surge bin. The configuration of the surge bin in relation to the two trunk belts was chosen by considering development cost, advantages, and disadvantages of each option. It was concluded and recommended that a 500 tonnes capacity surge bin is required to remove the bottleneck from the system.

Jan 1, 2010

By C. L. Reichardt

Mining companies are increasingly looking to the developing world for the next generation of mining projects, often in countries that have little or no previous history of large-scale mining. One of the major challenges for such projects is hiring?and retaining?personnel that have technical skills and experience in mining-related disciplines. Staffing a mine with an expatriate workforce is neither cost-effective nor sustainable, and many countries now insist that mining companies ?transform? the profile of their workforce to more closely mirror the demographic profile of the host population. The need to nurture mining-related skills in emerging mining nations is not solely limited to the workforce: there are also pressing economic and sustainability imperatives to develop capacity within local service providers such as consultants and contractors, as well as to facilitate informed engagement between mining companies, government and civil society. However, few educational institutions in emerging mining nations currently have the ability to offer practical training in mining-related disciplines. Local employees who are sponsored by companies to develop their skills through international study maybe impeded by language and cultural barriers, and may also be taught using course content that is of limited relevance to the specific challenges of their future working environment. This paper addresses the challenge of skills development and retention in emerging mining nations and uses examples from sub-Saharan Africa and the Asia Pacific region to explore practical means of developing capacity in mining-related disciplines. It examines the need for companies to implement strategies to develop local technical capacity in countries where they envisage a long-term operational future and also highlights the need to foster partnerships between academia, developmental institutions, mining companies, governments and civil society to establish the critical mass of mining-related skills required to nurture the development of a sustainable mining industry.

Jan 1, 2009

By M. Mabuza

Two Rivers Platinum Mine (TRP) is a 55:45 joint venture between African Rainbow Minerals and Impala Platinum, respectively. TRP is situated on the farm Dwarsrivier 372KT, in the southern sector of the eastern limb of the Bushveld Complex. Dwarsrivier is underlain by rock formations of the Critical Zone (Winterveld norite-anorthosite) and the Main Zone (Winnarshoek norite- anorthosite). Two economically significant PGE-bearing layers namely the Merensky Reef and the UG2 chromitite are found within the upper Critical Zone. These are approximately 140 m vertically apart, separated by a series of barren norites and anorthosites. At Two Rivers Platinum, only the UG2 chromitite layer is currently being mined for PGEs. The UG2 sub-outcrops north/south along the Klein Dwarsrivier river valley with a very gentle dip to the west of 7º?10º. At Two Rivers the UG2 averages about 120 cm in thickness, overlain by a waste pyroxenite parting about 20 cm thick, above which is a leader seam about 20 cm in thickness. The mineable cut consists of the leader seam, the waste pyroxenite parting, the UG2 chromitite layer including 25 cm of pegmatoidal pyroxenite footwall, below the UG2 reef to a minimum of 185 cm trackless mining cut. The mining method is a mechanized bord and pillar layout, which will yield a total of 185 000 tons at full run of mine production from the underground UG2 mine.

Jan 1, 2007

By W. Robert, J. Wirth, G. Grasselli

ABSTRACT: Strength, deformability and fluid flow properties of rock joints are to a great extent controlled by the surface roughness. The hydraulic conductivity of a rock fracture depends on the aperture distribution, the surface roughness and the contact area, each of which depend on the stresses that act on the fracture plane. However, despite much recent work, a complete understanding of the relationship between void space geometry, contact areas, applied stress, and hydraulic conductivity has yet to be achieved. Moreover, although in situ rock joints are subjected to both normal and shear loading, few studies have been conducted to investigate the effect of shear displacements on fluid flow through a single rock fracture, and which have addressed the issue of flow anisotropy induced by shearing. Experimental flow tests show that with increasing shear displacement, the fracture becomes heterogeneous and anisotropic, and becomes more permeable in the direction parallel to the displacement (Yeo et al., 1998). On the other hand, dry shear tests show that the surface fails in areas facing the shear direction (Grasselli and Egger, 2003). Moreover, the experimental results confirm that the shear strength of rock joints is direction-dependent. In this paper, a three-dimensional morphological description of several a natural fractures that have undergone shear displacement were generated using the Automated Topographic System at the University of Basel. The data analysis method of Grasselli (Grasselli et al., 2002a) is used to determine the surface parameters that are known to control the shear strength. Simulations of fluid flow through this fracture, in various directions relative to the direction of shear, are conducted using an FEM flow simulator. The results constitute the most detailed analysis yet undertaken of the relationship between shear displacement, shear strength, and fracture transmissivity. RESUME: La rugosité des joints en roche joue un rôle primaire sur la réponse hydromécanique du massif fracturé. En effet, la conductivité hydraulique des discontinuités en roche est influencée par la rugosité, et par la distribution des ouvertures et des zones de contact, dont chacun dépend de l’effort normal et du cisaillement qui agissent sur la surface du joint. Les essais d'écoulement en laboratoire montrent que si cisaillée, la fracture devient anisotrope, et plus perméable dans la direction parallèle au déplacement (Yeo et al., 1998). D'autre part, les essais de cisaillement indiquent que seules les zones de la surface qui font face à la direction de cisaillement sont impliquées dans le cisaillement (Grasselli et Egger, 2003). D'ailleurs, les résultats expérimentaux confirment que la résistance au cisaillement des joints de roche est dépendante de la direction. Dans cet article, plusieurs fractures en roche ont été analysées en utilisant un système de mesure topographique à l'Université de Bâle. La méthode d'analyse de données proposée par Grasselli (Grasselli et al., 2002a) a été employée pour calculer les paramètres de la surface qui déterminent la résistance au cisaillement. Plusieurs simulations du coulage, dans diverses directions relativement à la direction du cisaillement, ont été faites à l’aide d’un programme de calcul à éléments finis. Les résultats constituent une des analyses les plus détaillé sur le rapport entre le déplacement pendant le cisaillement, la résistance au cisaillement, et la transmissivité spécifique de la fracture. ZUSAMMENFASSUMG: Die Festigkeit, Verformbarkeit und Hydromechanik von geklüftetem Fels wird hauptsächlich von der Oberflächenrauhigkeit der Bruchflächen bestimmt. Die hydraulische Leitfähigkeit einer Kluft hängt von der Verteilung der Rissbreiten, der Oberflächenrauhigkeit und den Kontaktflächen ab, die ihrerseits von dem auf die Bruchfläche wirkenden Druck beeinflusst werden. Obgleich in letzter Zeit viel in dieser Richtung geforscht wurde, kann der Zusammenhang zwischen Porenraumgeometrie, Kontaktflächen, wirkendem Druck und hydraulischer Leitfähigkeit noch nicht vollständig erklärt werden. Obwohl Klüfte in situ sowohl Normal- als auch Schubspannungen ausgesetzt sind, wurde der Einfluss von Scherverschiebungen auf den Kluftwasserfluss und die daraus resultierende Fliessanisotropie in einer einzelnen Kluft bisher kaum untersucht. Experimentelle Untersuchungen des Durchflusses zeigen, dass die Kluft für größer werdende Scherverschiebungen heterogen und anisotrop wird wobei die Permeabilität parallel zur Verschiebungsrichtung ansteigt (Yeo et al., 1998). Andererseits zeigen trockene Scherversuche, dass die Oberfläche an Stellen versagt, die gegen die Verschiebungsrichtung anstehen (Grasselli und Egger, 2003). Des weiteren bestätigen die experimentellen Ergebnisse eine Richtungsabhängigkeit der Kluftscherfestigkeit. In diesem Artikel wird eine dreidimensionale morphologische Beschreibung mehrerer natürlicher, durch Scherspannungen verschobener Klüfte vorgestellt, die vom Automated Topographic System der Universität von Basel erstellt wurde. Das von Grasselli (Grasselli et al., 2002a) entwickelte Datenanalyseverfahren wird zur Feststellung der die Scherfestigkeit bestimmenden Oberflächenparameter herangezogen. Mittels einer FEM-Simulation wird der Durchfluss durch eine solche Kluft in verschiedenen Richtungen simuliert. Die Ergebnisse stellen die bisher ausführlichste Analyse des Zusammenhangs zwischen Scherverschiebung, Scherfestigkeit und Durchlässigkeit (Transmissivität) einer Kluft dar.

Jan 1, 2003

By G. L. Smith

The fundamental challenge facing mineral and metal companies is how to create sustainable value while operating within mandated strategic bounds, identified constraints, and variable market and economic conditions. This can be achieved by allowing the fixed physical nature of the mineral asset to drive definition of the optimal technical solution to mining and processing activities, and developing and resourcing a strategically aligned portfolio of production entities that creates flexibility to near- and longer-term business environment shifts, i.e. a production mix that allows variation of output to respond to short term market variation, within a long term context. The practical achievement of this outcome is enabled by the concept of strategic long term planning. The core elements of strategic long term planning in the metals and minerals industry, and the relationship between them, are expanded. The strategic long term planning framework is a logic construct that enables delivery of an optimized, strategically-aligned business plan from the mineral asset portfolio using a set of tools and techniques with a common language, standards, systems and processes to align decisions and actions on a cyclical basis.

Jan 1, 2012

By G. L. Smith

The fundamental challenge facing mineral and metal companies is how to create sustainable value while operating within mandated strategic bounds, identified constraints, and variable market and economic conditions. This can be achieved by allowing the fixed physical nature of the mineral asset to drive definition of the optimal technical solution to mining and processing activities, and developing and resourcing a strategically aligned portfolio of production entities that creates flexibility to near- and longer-term business environment shifts, i.e. a production mix that allows variation of output to respond to short term market variation, within a long term context. The practical achievement of this outcome is enabled by the concept of strategic long term planning. The core elements of strategic long term planning in the metals and minerals industry, and the relationship between them, are expanded. The strategic long term planning framework is a logic construct that enables delivery of an optimized, strategically-aligned business plan from the mineral asset portfolio using a set of tools and techniques with a common language, standards, systems and processes to align decisions and actions on a cyclical basis.

Jan 1, 2012

By D. C. Andersen, G. L. Smith, J. Pearson-Taylor

Following a restructuring of Anglo Platinum Limited in 2004 the strategic long-term planning function has been centralized. This paper describes the revised strategic long-term planning process covering aspects of the planning cycle, systems and methodologies, categorization of capital expenditure, corporate governance and planning tools.

Jan 1, 2006

Elongates are commonly used as stope support in South African gold and platinum mines. To evaluate the effect of the inherent strength, stiffness and yield variability associated with elongates, a statistical method is presented which addresses and quantifies the support performance at various levels of certainty. The analysis, which is based on a normal distribution, makes use of force-deformation curves determined from multiple laboratory compression tests on the same support type. The applicability of the method is illustrated making use of actual performance capabilities of various types of elongates. In order to ensure a high probability that support units installed underground exceed the standard support performance curve established by means of laboratory tests, the statistical mean of a suite of tests based on the same support type is downgraded. The ?correction factor? is a function of the mean and standard deviation of the test data, as well as the sample size of units deemed to control the local rock mass stability. It is shown that downgraded performance curves based on a high probability (90 to 95percent) of support units exceeding this performance level are suitable to ensure that the design of support systems will in variably meet the design criteria. In the highly discontinuous hangingwall rock mass typically associated with intermediate- and deep-level mining operations, the interaction between adjacent support units is comparatively limited (at the support spacings commonly used). Therefore, the appropriate sample size (n) of the support units controlling the local rock mass stability should be n= 1. In shallow mining conditions, sample sizes of up to n=5 may be warranted, depending on the spacing of joints and other discontinuities in the hangingwall.

Jan 1, 2001

Following a short review of selected literature, a back analysis of stress measurements of stress regeneration in a closed mini-longwall is shown. The agreement is good, lending confidence to the parameters used in the proposed numerical model. Foundation yielding was modelled in the absence of total stope closure. A ?Prandtl? wedge was formed, coinciding with the yield point of the pillar/foundation system. Some theoretical work is used as a starting point for the formulation of a new design methodology for strike or dip stabilizing pillar/foundation systems in deep level goldmines. The existing guideline for the stability of foundations (APS< 2.5UCS) is critically examined. Finally, the advantages of the new approach, and the work required to substantiate the proposed new design methodology, are outlined.

Jan 1, 1998

By M. H. Rogers

Coal has been at the forefront of mankind?s drive to improve his quality of life and also for sustainable development, from the Industrial Revolution onwards. The international coal industry today is large, with some 3,7 billion tons being produced and consumed in 1997. South Africa is an important participant in the coal industry, selling some 220 million tons in 1997 of which 64 million tons were exported. It is the second-largest thermal coal exporting country in the world. Despite the size of the world coal industry, it is not immune to change. The address examines growth projections for the industry and the change drivers that will impact on it in the future. Environmental pressures, the most important of which being the climate change debate, the Kyoto Protocol arising from this debate and the development of clean coal technologies, to reduce the impact of coal production and usage on the environment are considered. Other major change drivers considered are competition from other sources of energy and that between coal producers, the deregulation of the electric power industry, corporate restructuring and for the South African producer, legislative reform. The declining (real term) coal price, the consequent squeeze on margins and the need for producers to actively contain costs is covered. Technology has, in the past, been the driver behind the growth and change of the South African coal industry and its future role in ensuring that coal is the fuel of choice for continued improvement in standards of living and economic development is addressed.

Jan 1, 1999

By N. D. L. Burger

A low noise blast hole drilling system was developed to limit the risk of noise-induced hearing impairment in mining operations. Noise- induced hearing loss has been identified as a major occupational health risk in SA mines. The noise generated by pneumatic percussion drills is a major contributor to such noise-induced hearing loss. This motivated the South African Safety in Mines Research Advisory Committee (SIMRAC) to commission the development of a low noise rock drill system. The system had to be designed, manufactured, tested and demonstrated in a simulated underground mining environment. The specification required noise levels below 90 dBA. Other important design considerations were ease of manual transport, setting up and operation. The primary design concept was to encapsulate a standard SecoS215 pneumatic rock drill in a composite material tube. The tube is pushed onto the rock face by a pneumatic cylinder and is sealed at the rock face by an elastic seal. The drill is pulled towards the rock face by a rope and pulley mechanism fitted inside the tube. This mechanism is powered by a second pneumatic cylinder. The actions of moving and setting the drill require two persons. However, the team can carry out the drilling function itself on several drills simultaneously because of the self-thrusting design. The drill is supported by two camlocks. The exhaust (air containing dust, water, rock debris, oil and grease) is removed from the encapsulating tubes via an exhaust tube to the end of the stope. In this way exhaust noise and air pollutants are disposed of away from personnel. Tests were conducted in a test stope. Noise levels of under 90 dBA were achieved, thereby attaining the primary design specification. This was achieved without materially compromising ease of handling. Penetration rate was somewhat improved compared to that of the standard drill, so that productivity could be maintained. Keywords: Drill, rock drill, quiet, noise, mine, underground.

Jan 1, 2004

By A. Fahimifar, H. Soroush

Abstract: Triaxial tests were conducted on the schist specimens with various anisotropic angles under confining pressures of 0, 7 and 15 MPa, and axial stress-axial strains, were measured and plotted for various conditions. The results obtained reveal the effects of schistose on the strength and deformability of the rock very clearly. Peak strength of the specimens for 00 and 900 schistose orientations are nearly the same. Modulus of elasticity of this rock varies with anisotropic angle. For 0 orientation modulus of elasticity increases to a maximum. Confining pressure increases the peak strength and improves the rock deformability. However, this effect is not the same for various orientations, and there are no similar trends for each anisotropy direction. Analysis of the results shows that consideration of a linear failure criterion such as Mohr-Coulomb is appropriate for the prediction of rock behaviour up to 10 MPa, rather than a non-linear one. The analysis also reveals that the friction angle and cohesion are affected by the anisotropy orientation, and this effect is more important for the cohesion than the friction angles. Resume: Les esseys triaxiales sur les echantillon d un roch schist avec les differents angles non-isotrop sous les tension lateral zero et sept et qoinze mega pascal (mpa) est fait et les covtraite et allongment unitaire sont mesure et leur curues est destine sous different condition les resultats obtenues montre les effets du schistosite sur le resistance et le ductilite vissiblement. Le resistance final sur les echantilions pour les angles o degre et 90 degree est equivalent. Le modoule d elasticite de ce roch sera difere par a port de l angle de stratification. Pour l angle o degree le valeur de modoule est le maximum. le pousse lateral augmenterai le resitance final, et sera amilterai le toleran le de ductilite. Mais cette effet bn est pas unigue pour les different stratification, et pour les diferents directions no– isotrop it n y a pas le meme solution. L analyse des resulitats montre que le criterre de ruin comme mohr–colomb est moderate pour le pousse lateral jusq av lo mega pascal , et ce n est pas neccesaire d utiliser de criterre no–linear . Cette analyse aussi montre que l angle de frottement et cohsion est en relation de la direction no–isotrop, et cette effet est olus important pour le cohsion par a port de l angle de frottement . Abriß : Dreiachsige Prüfung wurde auf den schist Exemplaren mit verschiedenen anisotropic Winkeln unter Bestätigen von Drücken von 0.7 und 15 MPa geleitet, und axiale Spannung axiale Spannungen, wurden gemessen und für verschiedene Bedingungen wurde geplant. Die Ergebnisse haben die Wirkungen von schisocity auf der Kraft und dem deformability des Felsen sehr deutlich erhalten offenbart. Maximale Kraft der Exemplare für 0° und 90 sind° schistos Orientierungen beinahe das gleiche. Modulus der Elastizität von diesem Felsen ändert sich mit anisotropic Winkel. Für 0° vermehrt Orientierung modulus der Elastizität zu einem Maximum. Einschränkender Druck vermehrt die maximale Kraft und verbessert den Felsen deformability. Aber ist diese Wirkung nicht das gleiche für verschiedene Orientierungen, und es gibt keine ähnlichen Tendenzen für jede anisotropic Richtung. Analyse der Ergebnisse zeigt jener Überlegung Kriterium eines linearen Ausfalls wie zum Beispiel Mohr Coulomb passend für die Voraussage von Felsen Verhalten bis zu 10 MPa, anstatt eines nicht linear ist. Die Analyse offenbart auch, daß der Reibung Winkel und Bindekraft werden beeinflußt von der anisotropic Orientierung, und diese Wirkung wichtiger für die Bindekraft ist, als der Reibung Winkel

Jan 1, 2003

Abstract : The computation of reliability index or failure probability of slopes can be transformed into an optimisation problem. In high rock slope engineering, it is usually a multimodal optimization problem. The traditional optimization techniques are difficulty to find out the global optimal solution because of their easily falling into local optimal value. Recently, a new kind of bionic algorithm - ant colony algorithm (ACA) - has been used to solve this problem. In this paper, the structure of ant colony algorithm and the transfer probability of ants are modified to evaluate the failure probability of complicated slopes. A new adaptive ant colony algorithm (AACA) is proposed to determine critical slip surface and its corresponding failure probability of complicated slopes. A case study is given to verify the proposed approach. The results show that the presented method has obvious advantages compared with traditional methods. ZUSAMMENFASSUNG: Die Rechnung des Zuverlaessigkeitindexes oder der Zerstoerungswahrscheinlichkeit kann sich in einer Optimierungsfrage umwandeln, im Bauprojekt an hoehe Gebirgehang, handelt es sich meistens um eine Optimierungsfrage ueber Multi- Spitzenwert. Mit der traditionelle Optimierungsmethode ist es schwer eine umfassende Loesung fuer die Optimierung zu finden wegen des leichte Verfallens in Beschraenkung der Teiloptimierungsloesung. Mit dem neue Bionik- Algorithmus —— Ameisen - Kolonie- Algorithmus wird dieses Problem geloest. In diesem Text hat man eine Strukturverbesserungsloesung fuer das Ameisen- Kolonie -system und die Wahrscheinlichkeit der Ameisenkolonie erwaehnt, und damit wird man die Zerstoerungswahrscheinlichkeit des komplizierte Hangs feststellen. Mit dem neuen Ameisen- Kolonie- Algorithmus kann man die gefaehrlichste Gleitflaeche und die entsprechende Zerstoerungswahrscheinlichkeit herausfinden. Die in diesem Text beschriebene Methode wurde durch Praxis geprueft. Durch die Pruefergebnisse wurde es gezeigt und bestaetigt, dass der neue Bionik- Algorithmus vorteilhafter als der traditionelle Algorithmus ist. Résumé : Le calcul de l’indice la fiabilité ou de la probabilité de ruptures peut être transformé en un problème de l’optimisation. Pour le cas du génie des pentes de haut rocher , le problème se pose en général en l’optimisation de multi-crêtes. Les techniques traditionnelles conduisent facilement à la solution optimal partielle au lieu de celle globale. Récemment un nouveau type de bionique algorithmique a été appliqué pour la solution de ce genre de problèmes, c’est l’Algorithme Colonie de Fourmis. Dans l’article il est proposé de modifier la structure du système de la colonie de fourmis et la probabilité de transfert des fourmis en vue d’évaluer la probabilité de ruptures des pentes de haut rocher complexes, par ailleurs un nouveau algorithme adapté de colonie de fourmis est formulé pour déterminer la surface glissante critique et la probabilité de ruptures correspondante. Les techniques proposées dans l’article sont vérifiées à travers des expérimentations dont les résultats ont prouvé que les techniques présentées dans l’article sont évidemment meilleures que celles traditionnelles.

Jan 1, 2003

By P. Mbele

Iron ore concentrate is not easily transported to, or processed in, ironmaking plants, therefore it is necessary to agglomerate. This paper will determine the possibility of agglomerating Sishen concentrate into suitable ironmaking feedstock. Pelletizing is one of the conventional and preferred agglomeration processes for iron ore concentrate investigated at Kumba Value-In-Use Laboratories. Sishen concentrate was mixed with binder, and then pelletized using a laboratory pelletizing disc; afterwards the green pellets were indurated at high temperatures to give strength high enough to survive handling and lessen disintegration in the shaft during ironmaking. Sishen pellets have satisfactory physical and metallurgical properties which make them suitable feedstock for the direct reduction processes. These were tested under Midrex shaft operational conditions and performed well, with a metallization of 94.47% being attained.

Jan 1, 2012

By J. Madias, E. Benavidez, E. Brandaleze, L. Castella

Knowledge of the physical and chemical properties as well as the behaviour of the mould fluxes during melting, important in order to improve continuous casting operations. Lubrication and control of heat transfer in the mould are the more relevant functions of these materials. Values of physical properties like viscosity and surface tension at melting range temperatures are required, as much as the thermal behaviour under process conditions. The heat extraction from the liquid steel has an important effect in the final quality of products. Mould fluxes are constituted by different oxides, and may form glasses and crystal phases during cooling. The solidification rate and the chemical composition determine the proportion, type and crystalline morphology, which are responsible of the thermal transfer processes. In this paper, viscosity values are reported in the melting range temperatures calculated by means of the Riboud model and compared with fluidity results obtained by the inclined plane technique. Also the linear expansion of the mould fluxes at high temperatures was determined by dilatometry. The crystallization in two different fluxes was determined by DTA tests and correlated with the basicity index. Crystal phases were evaluated by scanning electronic microscopy on quenched samples at 1300°C. This information is relevant to increase the knowledge on the peritectic steel grades casting process in order to improve its quality. Keywords: mould fluxes, heat transfer, crystal phases, peritectic steels, thermal properties.

Jan 1, 2004

By P. Gonzalez, C. Ariyo, L. Holappa

Oxidation state of titanium was determined in CaO-SiO2-TiOxslags in the composition range25–53 per cent CaO, 27–46 per cent SiO2, 10–55 per cent TiOxat 1873K using gas equilibration method. In the experiments, slags with different titanium oxide contents were equilibrated with a known carbon monoxide and carbon dioxide ratio. The results were used to determine the Ti3+and Ti4+contents as well as the activity coefficient ratio of corresponding oxides in the slag. The dependency of the activity coefficient ratio as a function of oxygen partial pressure was determined. Keywords: titanium, titanium oxide, activity, activity coefficient, slag iron, carbon monoxide,carbon doixide, gas, equilibrium.

Jan 1, 2004

By K. Lombard

"‘Roof support awaiting time’ (RSAT) is a term used at Goedehoop Colliery’s Simunye Shaft to describe the potential production time lost due to the continuous miner (CM) standing idle waiting for roof support to catch up. Investigations revealed that in 2013, Simunye Shaft had approximately1400 hours of RSAT, which suggests that the mine could have potentially produced an additional 280 000 t of coal. This project consisted of two parts. Firstly, the causes of the high RSAT and means to improve the situation were investigated. Secondly, as insisted by mine management, the CM cutting sequence was investigated as a possible cause of high RSAT. Machine-related challenges due to the roofbolter installing support too slowly, geological conditions (mostly hard roof conditions and slips),logistical challenges pertaining to the CM cutting sequence, man-related challenges related to operator fatigue, re-support, operator inexperience, and the absence of support targets were identified as main contributors to RSAT. Furthermore, results showed that the roofbolters in the sections at Simunye Shaft are slower than the CMs. A target of 28% reduction in RSAT was set. Experts from Kennametal and Fletcher were consulted to find solutions for the identified causes. In total, eight solutions for RSAT were identified, but the solution that contributed most significantly to reducing RSAT was to use hard roof drill bits as a standard product at Simunye Shaft. Calculations showed that by using hard roof drill bits, RSAT can be reduced by 43%, which is more than the specified 28% target. The cutting sequences at Kriel, Greenside, and Simunye Shaft, togetherwith three newly developed cutting sequences, were simulated using the UCMS (Underground Coal Mining Simulation) program. A re-aligningprinciple was incorporated into the newly developed cutting sequences toalign the cutting sequences to general support work and to reduce RSAT. A decision matrix revealed that a cutting sequence in which boxing takesplace in R3 (third road to the right of the belt road) and in which the re-aligning principle has been incorporated will be the best option for Simunye Shaft. The recommended cutting sequence will lead to a 5% increase in production.The work presented in this paper was carried out as partial fullfilment for the degree BEng (Mining Engineering)"

Jan 1, 2015