Search Documents

By V. A. Leão, V. S. Coimbra, V. A. A. Oliveira, R. F. M. de Souza, G. M. de Lima

A willemite concentrate consisting mainly of willemite (55.3%) and dolomite (15.6%) was reduced in a tube furnace with charcoal as reductant. The effects of temperature and varying reductant additions on zinc extraction were studied. A zinc recovery of 86% was achieved with 20% reductant in the charge at 1100°C. During reduction, the calcium oxide generated through calcination of the dolomite promoted decomposition of the willemite, thus lowering the temperature at which reduction took place. The presence of CaO improved the zinc recovery at all temperatures studied. The best zinc recovery (93%) was obtained in the presence of 5% CaO, 20% charcoal reductant, and at a temperature of 1100°C. The results show that the willemite concentrate studied has great potential to be used as a raw material for the Waelz process.

Nov 6, 2023

By A. Refahi

For predicting the energy consumption during the size-reduction process, the Bond approach is often used. In this work, the PFC3D discrete element method (DEM) software was employed to model the crushing behaviour of some rocks with different mechanical properties in a laboratory jaw crusher. FLAC3D software was adopted to analyze the stress distribution in the rocks. The rocks studied were modelled as granular assemblies in the shape of a sphere and/or a cube located between two jaws, and the work done by the jaws in the crusher was determined. Nine different types of rocks were studied and the energies consumed by the crusher were compared to those of the Bond comminution energy estimated from the Bond index. There is considerable difference between Bond crushing energy and work done by the jaw crusher for rocks. It appears that the Bond approach is not a suitable method for predicting single particle fracture energy done by the crusher. To verify the results obtained from DEM models, the fracture behaviour of the crushed rocks was examined and was compared to the PFC3D results. The tensile mode of fracturing is favourably modelled by the PFC3D software while the delamination mode cannot be well modelled by PFC3D software. Keywords: jaw crusher; discrete element method; crushing energy; Bond index

Jan 1, 2009

By H. A. D. Kirsten

The assessment of backfill as a support medium in gold mines has been based generally on its ability to reduce the amount of potential energy available to cause damaging rockbursts. While this regional support effect is very important, the methods of analysis commonly used to quantify it predict that, owing to the very compressible nature of the fill, the support provided in areas of small convergence will be negligible. This prediction, however, is contrary to the conditions observed in practice, namely that weak fill does provide a discernible beneficial effect. In addition to the regional support effect, several mechanisms of secondary support, particularly those applicable to areas of low convergence, are identified and discussed. These include the mechanism of deformation of the detached hangingwall beam, rotational and shear effects on bedding, joints and fractures, joint infill, the continuous support effect of the backfill under static and dynamic conditions, the preservation of the integrity of the hangingwall beam, and the potential modification of local stress fields. Confidence in the validity of some of these mechanisms is afforded by the results of theoretical investigations into the behaviour of backfill- supported stopes. The results dealt with are: ? the behaviour of the hangingwall as a beam on an elastic foundation; ? the behaviour of stope/backfill, modelling the surrounding rock as a jointed rock mass.

Jan 1, 1988

By D. T. Jordan, L. C. Coetzee, G. Kalenga, T. Mahlangu, W. J. Shipman

Although online free cyanide analysers are widely available and used in gold leaching operations worldwide, reliable automated free cyanide concentration control is not consistently achieved in many of these operations. Effective cyanide concentration control is complex owing to amongst others, the long residence times and ore feed variations. Model Predictive Control (MPC) has been proven to provide superior cyanide concentration control over traditional proportional-integral-derivative (PID) control, leading to savings in operational costs and reduced leachable gold losses. In the first example reported in this paper, MPC has improved control of the free cyanide concentration by keeping it within the required range 73% of the time during testing, compared to the previous PID controller that only achieved this target 30% of the time. This represents a 143% improvement. Another example demonstrates a 22% reduction in cyanide usage as a result of using MPC. MPC functionality is rarely available on the programmable logic controllers (PLCs) and control systems installed at gold plants, hence it is implemented on a personal computer (PC) networked to the cyanide analyser and plant infrastructure. Mintek has developed an embedded MPC that installs into the Mintek Cynoprobe analyser, adding MPC functionality without the need for additional PC and network infrastructure, reducing installation costs. This allows plants to minimise their expenditure on additional infrastructure while gaining the benefits of superior MPC technology for multiple cyanide dosage points. This paper will present results showing that the embedded MPC performs as well as Mintek’s existing PC-based StarCS MPC controller, making it a viable alternative for infrastructure-constrained gold plants. Keywords: Model predictive control, gold cyanidation

Jan 1, 2020

By W. P. Channon, J. B. See

The reduction of fluxed and non-fluxed manganese, ores by ferromanganese silicide by W. P. CHANNON, B.Se. (Eng.), M.Sce. (Eng.) Wits. (Visitor) and J. B. SEE, B.Sce. Hons., Ph.D. (New South Wales), M.I.M., M.I.M.M. (Member) In South Africa, medium-carbonferromanganese is produced by the silicothermic reduction of slags containing MnO. Because of its importance in the production of refined ferromanganese, a study was made of the reaction between a premelted South African Mamatwan manganese ore and various ferromanganese silicide reducing alloys, with and without fluxing agents. Because the reaction is highly exothermic, temperature appeared to have little effect on the rates of manganese transfer to the metal and silicon transfer to the slag, and an apparent equilibrium was rapidly approached. Limits were determined for the favourable effects of fluxing additions, and manganese recoveries were found to decline as the ratio of CaO to MgO decreased as a result of the addition of basic flux. The recovery of manganese passed through a maximum, and subsequently decreased for variations in the ratio of alloy to ore. The results obtained, when used in conjunction with other physicochemical data related to this slag-metal system, suggest optimum slag compositions for the efficient manufacture of medium-carbon ferromanganese from Mamatwan ore.

Jan 3, 1977

By J. van der Walt, A. Whillier

Reference is made to the approach to mine cooling in which the service water is used as one of the means of distributing refrigeration, and attention is drawn to various engineering disciplines or functions necessary for effective distribution and reticulation of cold water from refrigeration plant. The demand for service water is intermittent, the peak flow-rates being typically two to three times the average flowrate. The refrigeration plant, on the other hand, must preferably be operated steadily throughout the day and night, with the result that a large storage dam for cold water must be incorporated into each system in order to even out the surge in demand for water. These dams should be operated as constant-temperature, variable-volume reservoirs. The conventional cascade system involving dams on each level is not the best for sending water down mines, and schemes are described that avoid the need for such dams. Reference is made to various tests that were carried out, and to several large systems that were installed. Management and organizational problems that could arise as a result of new technological developments in mine cooling are referred to, and cost figures are quoted to indicate the large potential savings, In addition to the improved environmental conditions, that can be achieved through the use of integrated water systems.

Jan 1, 1979

By S. Poirier, J. -M. Facteau

The gold mine sector is presently facing low gold prices as well as technological challenges. Its competitiveness and survival will depend on new mining methods and equipment to improve ore extraction. In 1999, Natural Resources Canada has invested new funds over a period of three years at CANMET’s Experimental Mine to establish the Narrow-Vein Mining Project. A team of engineers and researchers specialized in mining, mechanics and electronics engineering are working to meet the critical need of ore-extraction technology. CANMET’s programme in mechanization and automation for narrow-vein mining had, prior to 1999, realised several important achievements, many in co-operation with a consortium of mining companies(Soredem). The investment of new funds in this area will contribute to develop technologies to improve the productivity, as well as health and safety conditions of the narrow-vein mining industry. Several important impacts of this project will be monitored. In particular, a database of methods and equipment used in narrow-vein mining is being developed. A key thrust is to identify operators’ needs with respect to the development and automation of mining methods and equipment. Based on those needs, research and development projects will be created. The paper will present the objectives of the narrow-vein mining project and some of the results, including the web site developed to present the results of the project.

Sep 1, 2001

By T. A. Silva, A. C. Bragança

Lime has been added to the iron ore slurry transported by the Samarco pipeline since its operation start-up in 1977.Initially, internal corrosion was the main concern therefore the reagent was used only for pH correction. Over the last ten years, though, transport of more complex slurries demanded a significantly higher dosage of lime to guarantee adequate rheology control. Several other reagents have been tested for the same purpose yet none has proven to be as effective regarding technical performance, environmental impact and cost. However, an alternative was sought so that the slurry rheology could still be controlled in case lime addition became impracticable. The objective of this paper is to present a technical solution for this matter, which takes into account environmental aspects. It consists of adding soda for pH correction and an organic coagulant as a rheology modifier. The latter is a quaternary ammonium salt which affected the slurry transport properties in the same manner as lime when tested in a laboratory. It showed no plug formation and allowed solid particles to settle, forming a loose sediment after rest. These results indicate a low probability of plug occurrence in the pipeline and the formation of a readily reslurryable sediment upon shutdown of the pumping system. Industrial tests should be performed in order to validate the laboratory results.

Jan 1, 2007

By T.R. Stacey

Physical testing of rock support for rockbursting conditions has been carried out for over 40 years. A review of this testing shows that it has been mostly component based, rather than actually testing support systems. Further, it is concluded that none of the testing is truly representative of rockburst loading in a similitude sense. Similitude conditions are not achievable, mainly because the real conditions in a rockburst event, such as seismic source location and magnitude, wave frequencies, amplitudes, and interactions, are not all known. Because such information is not available, and because the results of all testing carried out to date have not been able to define, for support design purposes, the capacity of support systems, ongoing physical testing of rockburst support systems is essential. It is essential that the test should simulate, or actually take place in, a supported rock excavation. A rock support system is a combination of individual support components that work together to retain and contain the rock. In doing this, the components are subjected to loading by the rock and to interactive loading between one component and another. It is necessary to prove the capacity of such rockburst support systems by subjecting them to severe loading, as in direct blasting. The direct blasting approach, pioneered more than 40 years ago, probably still provides the greatest validity as a significant test of rockburst support capabilities, even though it does not simulate a rockburst. Direct blast testing of rockburst support systems in a surface environment, such as in a quarry or on exposed rock cutting surfaces, could represent a practical development of the approach, facilitating the execution and monitoring of tests.

Jan 1, 2012

By R. Hemp

This paper describes in broad outline the development of a computer programme for determining the effects of changes in various factors in the condenser water circuit on the operation of a cooling plant. The programme is used to obtain design figures which result in minimum total power consumption. This was done for a range of different upcast air quantities, and the implications of low air quantities for heat rejection are discussed.

By N. Sinclair

"In open pit dozer bulk push operations, the material left resting against the highwall after blasting poses an issue. This is because dozers cannot physically get in behind the waste to begin the bulk pushing process. Instead, an excavator can be used to side-cast this waste for the dozers to access. An alternative technique is to have the dozers ‘side-cut’ the material, which involves the dozers running parallel to the wall, digging out the material, and eventually rotating their blades to begin bulk pushing. Industry practices suggest the latter technique is less productive and economical than using an excavator. However, such excavator sidecasting ‘economic viability’ assumes that smaller/ancillary type excavators are used (i.e. less than 23 m3 bucket capacity). So, what happens if some mine sites are restricted to using relatively larger excavators (> 23 m3 bucket) that are preferred for higher priority digging tasks? When can they avoid using their excavator? This paper explores multiple scenarios that have been designed and developed to simulate data results, which identify conditions in which the dozer side-cutting technique becomes more economically viable than excavator side-casting in terms of decreased unit cost per loose cubic metre. IntroductionOptimizing the cost of waste removal operations is important for the profitability of opencast coal mines. In the past decade, dozer bulk pushing has emerged and taken over from traditional waste removal operations such as dragline and truck-and-shovel methods at various sites around the world (Beatty, 1994). In a typical bulk push operation, once the bench has been blasted, waste is left resting against the highwall, which can either be cleared using a loading unit or by having the dozers ‘side-cut’ the highwall.Dozers perform most effectively when slot dozing side-by-side, perpendicular to the highwall. However, when dozers are required to remove material off the highwall, they must push parallel to the highwall, rather than perpendicular, hence ‘side-cutting’ the material to ensure a clean face. While dozer sidecutting is possible, it has been found that the majority of mine sites use a loading unit in this situation to avoid dozer inefficiency. Other perceived issues with dozer side-cutting include higher maintenance requirements and safety risks to dozer operators working in close proximity to the highwall."

Jan 1, 2019

By K. Hodgson, J. P. M. Hojem, N. G. W. Cook

Already about one-third of South Africa's coal is mined at depths exceeding 100 metres. Almost all this mining is done by the bord and pillar method. Conventional design procedures call for ever larger pillars as depths of workings increase, resulting in the loss of large amounts of coal and reductions in productivity. Barrier pillars are in general use to ensure against large collapses. The presence of these strong pillars would allow a more efficient design of the bord and pillar layout to yield improved extraction ratios by using smaller, yielding, pillars between the bords. Knowledge of the complete load- displacement curves for such pillars is a prerequisite for the design of such a system. A 100-MN, stiff jacking system for measuring the complete load-displacement curves of pillars with cross-sections of up to 2 m X 2 m is described. The jacks are installed in a slot cut across the central plane of symmetry of a pillar, thereby ensuring that the stress distribution in the pillar during a test, especially at its contacts with the roof and floor, is identical to that caused in a similar pillar by convergence across the seam. Preliminary results in the form of complete load-displacement curves for test pillars of about 1.5 metre square section are given.

By K. Eckert, A. E. Sommer, S. Heitkam

One highly relevant challenge in flotation is the recovery of fine particles. Due to their low inertia, these particles are mostly pushed aside by rising bubbles. Consequently, they typically exhibit low probability for bubble-particle collision and thus, a poor recovery rate. In this work, the trajectories of fine particles in the vicinity of rising bubbles were investigated. The measurements considered a chain of millimetric bubbles in a rectangular container filled with deionized water. The flow field near the bubbles was measured by tomographic particle image velocimetry (TPIV), employing fluorescent tracer particles of 33μm diameter. Subsequently, trajectories of larger particles and bubble-particle collision events are recorded with 4D particle tracking velocimetry using a high temporal and spatial resolution. The results reproduce the well-known collision of particles on the leading edge of a rising bubble. Additionally, collisions on the tailing edge were observed in cases with a low Stokes number. The TPIV results demonstrate, that the high turbulent kinetic energy in the bubble wake allows particles to divert from the fluid streamlines and collide with the tailing edge of the bubble. The tailing edge collision probability increases with the bubble Reynolds number and decreased particle inertia. Overall, the investigation shows that the collision of fine particles in the bubble wake should be considered for the development of further collision probability models. Furthermore, the importance of turbulence on the fine particle flotation was demonstrated. Keywords: 4D Particle tracking velocimetry (PTV), tomographic particle image velocimetry (TPIV), fine particle flotation, collision probability, bubble-particle interaction, wake induced collision

Jan 1, 2020

By M. M. Bwalya, F. K. Mulenga

"SynopsisThe application of the attainable region (AR) technique to the analysis of ball milling is currently limited to batch data. This paper introduces the use of the technique to continuous milling.To this end, an industrial open milling circuit processing a platinum ore was surveyed. Samples were collected and later characterized by means of laboratory batch testing. On site, several milling parameters were varied systematically so as to collect data for modelling purposes. These paramters included ball filling, slurry concentration, and feed flow rate. After data analysis, a simulation model of the open milling circuit was developed under MODSIM®, a modular simulator for mineral processing operations. The mill was then simulated and the data generated was analysed within the AR framework.Initial findings reveal an opportunity to gain valuable insight by studying milling using the AR technique. From an exploratory perspective and inasmuch as this study is concerned, feed flow rate, ball size, and ball filling were identified as being pivotal for the optimization of open ballmilling circuits. Mill speed, on the other hand, had only a limited effect on the production of particles in the size range -75 +10 µm.IntroductionGlasser and Hildebrandt (1997) propounded the attainable region (AR) as a technique for the analysis of chemical engineering reactor systems. Results have since been produced and tested on both the laboratory and pilot scales. The method results in a graphical description of chemical reactions by considering the fundamental processes taking place in the system, rather than the equipment. From the plotted graphs, the process and the reactors can be synthesized optimally into a flow sheet.The use of the AR method still has a long way to go as far as mineral processing is concerned. For instance, several articles have reported the application of the AR technique to ball milling: Khumalo et al. (2006, 2007, 2008); Khumalo (2007); Metzger et al. (2009, 2012); Metzger (2011); Katubilwa et al. (2011); Hlabangana et al. (2012). Their main shortcoming has been the exclusive use of laboratory batch grinding data.To address this deficiency, Mulenga and Chimwani (2013) proposed a way by which the technique could be extended to continuous milling. In effect, the batch milling characteristics of a platinum-bearing ore (Chimwani et al., 2013) were used and scaled up to an open milling circuit. Then, with simplifying assumptions, an attempt was made to optimize the residence time of particles inside the mill. Later, Chimwani et al. (2014a) presented some optimization examples involving various milling parameters. The sequence of published articles then paved the way for the study of industrial milling systems with the AR methodology."

Jan 1, 2015

By L. Cong, C. Liu, N. Zhang, W. Cao, C. Zhou, X. Fan

"The modes of occurrence of arsenic and the effects of low-intensity leaching-flotation on arsenic removal from coal slime from the Tanggongta Plant, Inner Mongolia, China were investigated. The coal slime was examined using hydride generation inductively coupled plasma optical emission spectrometry and X-ray diffraction to obtain the content of elements and the major minerals. The modes of occurrence of arsenic in minerals were determined using selective leaching, float-and-sink analysis, and polarized light microscopy. The results indicate that pyrite is the dominant carrier of arsenic in the coal slime, which predominantly exists in association with clay. Significant proportion of the arsenic is removed by a low-intensity leaching-flotation process, consistent with the data from selective leaching and flotation of gangue. The results show that low intensity leaching-alkali washing-flotation is more efficient than direct flotation and low-intensity leaching-flotation.IntroductionUnderstanding the occurrence of arsenic in coal and its removal is significant in optimizing coal utilization, because arsenic in the environment is viewed as a potentially toxic trace element (Finkelman, Belkin, and Zhang, 1999; Hall, 2002; Smith et al., 1992; Smedley et al., 2003; Zheng et al., 1999). Many studies on the modes of occurrence and concentration trends of arsenic in different coal and washing products have been performed (Diehl, Goldhaber, and Hatch, 2004; Kolker et al., 2000; Quick and Irons, 2002; Wang et al., 2006; Fan et al., 2016). Trace elements are usually preferentially associated with certain minerals and the form that these minerals take will influence the efficiency of removal during cleaning (Quick and Irons, 2002). Arsenic is mainly associated with minerals such as pyrite, carbonate, and silicate (Demir et al., 1998; Diehl, Goldhaber, and Hatch, 2004; Zhou et al., 2014). The existence of organically bound arsenic was also confirmed using X-ray absorption (Kolker et al., 2000). However, inorganic arsenic is the principal source of pollution because of its leachability and high concentration compared with organic arsenic (Fujino et al., 2004; Gao, Lu, and Wang, 2010; Jiang et al., 2008; Kolker et al., 2000)."

Jan 1, 2017

By N Morales, G Nelis

Short-term plans must meet the long-term goals while accounting for shovel selectivity, operational space, and scheduling restrictions. There are several approaches that deal with these issues to deliver a feasible short-term schedule. This paper compares two approaches based on mathematical programming to address the short-term mining cut definition and scheduling in an integrated way. They work by scheduling extraction to comply with long-term production goals, but they differ in how mining cuts are modelled. The first approach schedules Selective Mining Units (SMUs) but aggregates them around predefined locations. The second approach does not work on SMUs; it decides directly what mining cuts are to be used from a pre-defined set of shapes. It assigns a destination and schedules the extraction for the selected mining cuts. We applied both approaches in a real case study to compare their results in terms of profit, mining cut design, expertise needed, profit, and optimisation performance.

Sep 1, 2021

By J. R. Percival, L. Ip, M. D. Piggott, S. J. Neethling

Component wear due to particle-laden flow is a significant challenge in the minerals processing industry in the handling and transportation of abrasive mineral slurries. Studying wear through experimentation is time-consuming and expensive; therefore possessing the ability to accurately simulate, understand and predict wear in these complex environments is highly desirable. The ability to predict wear is important in both the design of equipment in order to maximise the performance over the wear life of the components, as well in minimising potentially costly and dangerous failures and unscheduled maintenance.. Particle-induced wear is a complex problem, requring an understanding of coupled fluid-solid motion, geometry deformation in response to fluid-solid behaviour, moving geometries and wear modelling. Although the literature demonstrates that rebounding particles and changes to surface profiles can have a significant effect on subsequent wear rates and patterns, the challenge of implementing a model to account for this effect in complex geometries has been addressed by only a few authors in the literature. This paper describes a new wear simulator, leveraging fluidity, an open-source, massively parallel, finite element based CFD simulator capable of unstructured adaptive meshing. The wear simulator includes the ability to model particle-laden flow using representative Lagrangian particles and dynamic remeshing of geometry in response to wear and component movement. These capabilities are demonstrated using wear and the associated dynamically deforming boundaries within a Coriolis tester arm, with the results comparing favourably with the experimentally observed wear patterns. Keywords: CFD, wear, two-phase flows, anisotropic mesh adaptivity, boundary deformation

Jan 1, 2020

By K. Shame, H. H. Thiele

South Africa holds approximately 70% of the world’s total chrome reserves. Chromium is an important raw material for the production of stainless steel and ferrochrome alloys. Over the years, China’s ferrochrome market has been dependent on chrome ore imports from South Africa. In 2018, China imported about 75% of its chrome ore from South Africa. With the low platinum price and the rising demand for stainless steel, a growing demand to evaluate new beneficiation technologies for fine chromite was identified. Gravity separation of fine chromite (<75 μm) is inefficient, due to the limitations of the technology to upgrade fine particle size distributions. Potential for the recovery of chromite, specifically fines (<75μm), lost to UG2 PGM flotation tails, but also from MG and LG6 spiral circuit tailings exist. Flotation of podiform chromite ores from India and Kazhkhstan is successful in generating saleable product grade, following acid or alkaline flotation routes. Application to South African stratiform chromite is being evaluated, with the emphasis on evaluating reagent type, optimising dosages and the effect of pH in optimising flotation performance. Flotation can unlock additional value from chromite tailings material. The effect of ore characteristics such as gangue mineralogy, particle size distribution and headgrade are reported. The performance in terms of product quality and yield are evaluated and compared. The impact of this paper will not only prolong life of mine and increase revenue but will also alleviate environmental burdens associated with tailings dams. Keywords: Chromite, flotation, fine material, performance optimisation

Jan 1, 2020

By T. G. Pedro, Q. Gonzalo, R. E. Roberto

Anionic surfactants, such as oleic acid and sodium oleate (OLE), and cationic surfactants, such as dodecyl amine-hydrochloride (DDA), are used as flotation collectors of spodumene. However, recovery is poor even if activating ions are used because gangue minerals are also activated. Some reports demonstrate that OLE/DDA mixtures act as a selective collector to enhance spodumene recovery. From mostly macroscopic tests, it has been argued that anionic OLE and cationic DDA form electroneutral complexes, which are adsorbed on the mineral surface through chemisorption; however, no molecular evidence has been presented. Therefore, the adsorption mechanisms of the collector mixtures remain mostly unknown. It seems necessary to first study the behaviour of these surfactants confined in salt solutions, to determine auto-associations when they are pure and cross-associations when mixed, the transition from monomers to micelles, and the structure of the micelles and the effects of pH, temperature and concentration. In this paper, ab initio calculations are first used to determine the surface charge distribution of OLE and DDA separately. Then molecular dynamics simulations are used to determine the conformation, aggregation, and diffusion of these pure and mixed surfactants in freshwater and saltwater with the ionic strength of seawater in a pH range. In particular, it is interesting to determine the various associations that result in mixtures of both surfactants and the impact of alkali and alkaline earth metal cations on the structures formedp. Cations influence the order of the structure and orientation of water dipoles, reducing the mobility of water, ions, and surfactant molecules. This knowledge is critical to improve the molecular understanding of the adsorption mechanisms on minerals. Keywords: Computer simulation, molecular dynamics, flotation, collectors, saltwater

Jan 1, 2020

By M. Gomo, L. S. Mokhahlane

"Underground coal gasification (UCG) is an unconventional mining method that converts coal in situ into a fuel gas that can be used for electricity generation. Residue products from UCG have the potential to leach into surrounding groundwaters. The geochemistry and leaching dynamics of these products are explored in this study. The products include char, ash, and the heat-affected zone in the surrounding rocks. Core samples from the pilot plant at Majuba are the first ever to be recovered from a UCG cavity in Africa, and they give key insights into the geochemistry of the gasification zone. Mineralogical and chemical analyses were performed on the samples, and acid-base accounting (ABA) was used to predict the acid-producing capacity of the gasification zone, particularly for char samples. Some of the char contained pyrite, although not all samples were acid-producing as determined by the ABA analysis. The ABA results showed that some of the unburned coal has moderate levels of sulphur, which could be the driving medium for acidic conditions. The ABA analysis indicated that water in contact with the gasification zone would eventually have a pH lower than 7, which could lead to acid rock drainage. These results form part of a preliminary investigation into the geochemistry of the reaction zone, post gasification. IntroductionUnderground coal gasification (UCG) is an unconventional mining method that converts coal in situ into a fuel gas that can be used for industrial purposes, including electricity generation. The gasification process leads to the formation of a cavity composed of char, rubble, and void space (Bhutto, Bazmi, and Zahedi, 2013). Residue products from UCG have the potential to leach into groundwater. These products include char (devolatilized coal), which can generate acid rock drainage (ARD). ARD is caused by the oxidation of sulphide minerals, which acidifies the leachate, thus increasing the solubility of some environmentally toxic metals (As, Cd, Hg, Pb, Zn, etc.) (Bouzahzah et al., 2015).The main source of ARD is oxidation of sulphide-bearing minerals due to interactions with oxygen, water, and microorganisms (Simate and Ndlovu, 2014; Kefeni, Msagati, and Mamba, 2017; Bouzahzah et al., 2015). Although ARD occurs naturally, it can be enhanced by mining activities that escalate exposure of sulphide minerals to water, air, and bacteria (Simate and Ndlovu, 2014). At the Majuba pilot plant, the unburned coal remaining in the cavity has been in contact with groundwater since the gasifier was shut down in 2013. It is possible that in a commercial UCG plant, most of the coal will be consumed and no unburnt coal will be left in the cavity. Most of the sulphur will be converted to H2S during the gasification process and transported with the syngas to surface, where it can be removed and captured as elemental sulphur."

Oct 1, 2018