Search Documents

By M. E. Volin

The Smuggler is one of the mines in the Aspen district, located the central part of Pitkin County, Colo. It was first examined in July 1943 by C. R. Wilfloy, former mining engineer of the Bureau of Mines at Salt Lake City, Utah, in, company with the lessees, R. D. Rohlfing of Aspen and J. W. Vanderwilt of Denver. The purpose of this examination was to sample a mineralized breccia zone that appeared continuous along the contact between the Leadville and Weber formations. These preliminary samples showed that the zone contains low but significant amounts of lead and zinc and that the minerals are partly oxidized and thus not easily concentrated. The mine was examined again in May 1946 by the senior author and William Herron, one of the present lessees of the property. This examination reviewed the previous sampling and recommended investigations by the Bureau of Mines. Sampling and drilling investigations were conducted by the Bureau from October 1946 to February 1947 and again from August 1947 to April 1948. Aspen is the center of a famous mining district that produced over $102,000,000 in silver and lead ores from 1880 to 1918, when a dispute closed down the mines (fig. 1). All of the workings below the Cowenhoven tunnel in Smuggler Mountain and the lower Durant tunnel in Aspen Mountain have been flooded since that time. The Cowenhoven portal now is caved, and Smuggler Nos. 1 and 2 tunnels are the only accessible workings in Smuggler Mountain. The only operating mine is the Midnight, situated 4 miles south of town at an altitude of 9,700 feet.

Jan 1, 1950

By S. Stephen Uslan

The purpose of the study was to demonstrate the effect of positive reinforcement, specifically, social reinforcement (SR), on the frequency of eye, hand, and back injuries at four experimental salt mines. Injury data was collected from January, 1976, for the prePOMOST period and from the onset of training to September, 1978, for the post-POMOST period. All data was collected on a month-by-month basis. For the training period approximately 100 managers and supervisors from five plants were trained in the use of positive reinforcement for occurrences of "safe behavior." Each supervisor was also provided manuals and other supportive materials. Additionally, following training, all supervisors were provided some coaching experience to keep the knowledge and capabilities gained during training from being extinguished. The analysis showed significant injury reductions in two sites and no injury reductions in the other two. When the injury data was corrected for the additional man hours expended in the postPOMOST period, a third site showed reduction in injuries. Similar findings were shown when the experimental sites were compared to other sites in the industry. The results were interpreted to support the hypothesis that the application of social reinforcement is related to a reduction in injuries.

Jan 1, 1978

By E. A. Magill

This report is one of a series prepared by the Bureau of Mines on manganese deposits of the Northwestern States. It describes properties on the Olympic Peninsula, Wash. Exploration by the Federal Bureau of Mines in 1939-40 and 1954-55 on several typical deposits is summarized, and examination data are presented for other manganese deposits on the peninsula. An attempt was made to list all known occurrences; however, some properties are abandoned, and their exact location is unknown.

Jan 1, 1960

By R. G. Knickerbocker, T. E. Evans, D. R. Torgeson

"INTRODUCTION Sponge iron is a product resulting from the reduction of an iron oxide at such a low temperature that fusion does not occur, and the reduced particles retain substantially the same shape as the original ore. The removal of oxygen in the reduction process leaves the metal porous and reactive. Sponge iron may be compared in general to a chemically precipitated substance insofar as reactive properties are concerned. The high specific surface and the orientation of metallic structure are factors which probably contribute to the reactive properties of sponge iron.The term ""gaseous reduction,"" as applied to iron ores, required clarification. Strong evidence exists, for example, that ore is partly reduced to sponge iron by carbon monoxide in the blast furnace at temperatures around 800° C. at a point that may be as high as 30 feet above the tuyores. In 1923 and 1924, Sims and Wood attempted to reduce iron oxide with carbon in an Arsem vacuum furnace at 980° C. These investigators found that only 6 percent of the iron was reduced to metal when the iron oxide-carbon mixture was heated for 1 hour under evacuated conditions, whereas at atmospheric pressure 70 percent of the iron was metallized. Their results indicate that the process of iron-ore reduction at temperatures below the melting point of the ore may proceed largely, if not entirely, by the action of reducing gases even when the reducing agent is solid carbon. Therefore, the term ""gaseous reduction,"" as used heroin, is defined as a process in which iron ore is brought into intimate contact with a reducing gas produced in separate-equipment from the reduction chamber itself.A large amount of pilot-plant development on gaseous reduction of iron ores has been carried out by the Bureau of Mines at the Boulder Experiment Station and had as its objective the reduction of fine iron ore by means of producer gas. The use of use gas was prompted by two considerations: First, the possible utilization of large reserves of Western noncoking bituminous coals and lignites contiguous to iron-ore drewwing; and second, an investigation of the results that might be achieved in the pilot-plant gaseous reduction of fine iron ores by means of a relatively reducing gas. The results obtained, it was felt, would be of considerable value in indicating the direction which gaseous reduction experimentation must take for the development of a commercially practicable and economic process for the production of sponge iron."

Dec 1, 1946

By Joan Weinberg

The real gross national product (GNP) expanded by 2.3% during the second quarter, down from the anomalous 4.4% growth rate in the previous 3 months. If the expansion continues through October, it will have lasted 5 yr and become the second longest in 40 yr.2 As in the first quarter, improvement in U.S. exports played a role in the continuing--albeit slow--growth. More than 2 yr of declines in the dollar relative to currencies of other industrial countries have contributed to a slight reduction in the trade deficit in real (volume) terms, as real net exports of goods and services rose $1.9 billion (table 1). Exports grew a strong 12.1% while imports, which had fallen the previous two quarters, rose 7.4%. Manufactured goods and petroleum products accounted for most of the second quarter import increase. The American Petroleum Institute estimates that the volume of crude oil and refined products imports in the first half of 1987 surpassed those in the same period last year by 7.5%, reflecting falling domestic production and higher than expected demand. Expenditure on durable goods--those that last at least 3 yr-by both consumers and producers also contributed to the second quarter expansion. Personal consumption of durable goods rose 9.0%, after having fallen the two previous quarters. Motor vehicle purchases accounted for most of the second quarter increase and the first quarter decrease. Sales of automobiles surged in the last quarter of 1986, as consumers rushed to capture the sales tax deduction that was eliminated on January 1. Sales fell in the first quarter of 1987, but have now moved closer to the trend line exhibited in the first three quarters of 1986. Automobiles accounted for half the 0.8% July gain in retail sales, and two-thirds of the 1.4% June gain. Producers durable equipment purchases also rose this quarter, accounting for the increase in nonresidential fixed investment.

Jan 1, 1987

By A. R. T. Denues

"INTRODUCTION The orienting phases of the current investigation of cushioned blasting in the Explosives Division of the Bureau of Mines were indicated in a previous publication (5) 3/. Pertinent literature reviewed therein indicated a highly controversial field. This emphasized the need for experimental studies of many factors that affect the health and safety of miners and the efficiency of mining operations. Results of some orienting tests showed marked effects on practical hazards. Further, they emphasized the necessity and importance of the contemplated investigation. The scope and general plan of these practical inquiries into the safety of cushioned blasting were indicated.This investigation of cushioned blasting relates to the various means employed to reduce the intensity of application of energy from explosive actions in boreholes. It has been suggested (from p. 19 of reference 5) that the divisions of this work would correspond to the salient hazards affected by cushioned blasting. These include the ignition hazard, hazards from poisonous gases, and other practical hazards in the blasting technique. The ignition hazard was resolved into two components of approximately equal weight. These include studies of effects upon (1) the incendivity of blown-out shots and upon (2) the occurrence of such shots. Experimental studies of effects on the incendivity of blown-out shots were first undertaken. Questions of the best procedure for making these evaluations have been adduced, and the interpretation and utilization of the results of gallery testing seemed to require detailed attention; some preliminary general considerations of such testing were therefore necessary."

Jan 1, 1943

By R. H. Fernald

In 1900, as far as available records show, there were only two producer-gas power installations in the United States. In June, 1915, the number probably exceeded 1,000. Of this number, some 84.5 per cent comprised small plants using anthracite, and only about 15 per cent of the total number utilized bituminous coal and lignite. In addition to these, two plants used wood, and three or four used oil. In the main, however, the larger sized units are operating on bituminous coal and lignite.

Jan 1, 1916

By D. G. Willard

The U.S. Department of Interior, Bureau of Mines has evaluated the potential resource and annual availability of cobalt from 27 deposits or districts in 11 market-economy countries. More than 95 pct of primary cobalt production from market-economy countries, mainly byproduct output from copper and nickel operations, was analyzed. Approximately 1,200,000 mt of cobalt is potentially recoverable at the demonstrated resource level. Very large additional resources exist, especially in laterite deposits, but are at the inferred level. The producing operations evaluated in this study are expected to produce about 19,000 mt of cobalt in 1989, significantly less than the available capacity of about 31,000 mt. More than 14,000 mt per year of cobalt is produced from copper-cobalt deposits in Zaire and Zambia, of which 11,000 mt can be produced at a copper price of $O.60jlb or less with a O-pct discounted cash-flow rate of return (DCFROR). Approximately 4,400 mt of cobalt is produced annually from nickel-cobalt deposits in six countries, of which about 1,800 mt (in Canada and Brazil) could be produced at a nickel price of $1.50jlb or less at a D-pct DCFROR. Approximately 200 mt per year of cobalt is produced from a cobalt mine in Morocco. Most of the evaluated nonproducing operations and prospects that could potentially produce cobalt as a principal product or byproduct would require a total cost (including a 15 pct-DCFROR) significantly exceeding January, 1989 market prices of the principal commodities. Principal-commodity dependence, transportation routes, cobalt toxicity, and other issues that could affect the availability of cobalt are addressed herein.

Jan 1, 1991

By B. W. Gandrud

This report, consisting mostly of float-and-sink data and washability curves, has been prepared in connection with an exhaustive study of coal preparation in Alabama conducted, by the U, S. Bureau of Mines and the University of Alabama with the cooperation of the different coal operators On the basis of the float-and-sink data, an attempt has been made to determine approximately the extent of ash and sulphur reduction obtainable under given conditions on coal from the mines which were sampled, In the coal-producing districts of Alabama a great deaf of attention has been given in recent years to the problem of improving preparation methods so as to obtain from various coal beds the best possible grade of washed coal. This is especially so where the washed coal is used for the making of metallurgical coke in by-product plants or where there are possibilities of using the coal for this purpose. In the manufacture of metallurgical coke, the sulphur content of the coal is a very important consideration. It is quite often the determining factor as to whether or not a certain coal can be used for coke making. In the studies which form the basis for this report, all samples have been analyzed for sulphur in order to obtain information regarding the possibilities of sulphur elimination as well as ash reduction, and the samples on which reports are made were obtained from beds that are characterized by rather high percentages of sulphur. In connection with the present investigations of coal preparation in Alabama a standardized method of interpreting float-and-sink data has been used extensively for predicting the ash and sulphur reduction and yields obtainable in a commercial washing plant from various sizes of raw coal and from the raw coal as a whole after a certain degree of crushing. This method, which will be explained in subsequent chapters, was used in interpreting the data contained in this report. The samples used for these washability studies were obtained from the following mines in the Warrior field of Alabama: Beltona mine on the Jefferson bed; Dolomite and Mulga mines on the Pratt bed; Coal Valley No. 163 and Coal Valley No. 11 mines on the Corona bed; Cedar Cove mine on the Carter bed.

Jan 1, 1932

By B. W. Candrud

This report, consisting mostly of float-and-sink data and washability curves, has been prepared in connection with an exhaustive study of coal preparation in Alabama conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal operators on the basis of the float-and-sink data, an attempt has been made to deter-mine approximately the extent of ash and sulphur reduction obtainable under given conditions on coal from the mines which were sampled. In the coal-producing districts of Alabama a great deal of attention has been given in recent years to the problem of improving preparation methods so as to obtain from various coal beds the best possible grade of washed coal. This is especially so where the washed coal is used for the making of metallurgical coke in by-product plants or where there are possibilities of using the coal for this purpose. In the manufacture of metallurgical coke, the sulphur content of the coal is a very important consideration. It is quite often the determining factor as to whether or not a certain coal can be used for coke making. In the studies which form the basis for this report, all samples have been analyzed for sulphur in order to obtain information regarding the possibilities of sulphur elimination as well as ash reduction, and the samples on which reports are made were obtained from beds that are characterized by rather high percentages of sulphur. In connection with the present investigations of coal preparation in Alabama a standardized method of interpreting float-and-sink data has been used extensively for predicting the ash and sulphur reduction and yields obtainable in a commercial washing plant from various sizes of raw coal and from the raw coal as a whole after a certain degree of crushing. This method, which will be explained in subsequent chapters, was used in interpreting the data contained in this report. The samples used for these washability studies were obtained from the following mines in the Warrior field of Alabama: Beltona mine on the Jefferson bed; Dolomite and Mulga mines on the Pratt bed; Coal Valley No. 16B and Coal Valley No. 11 mines on the Corona bed; Cedar Cove mine on the Carter bed.

Jan 1, 1932

By A. U. Miller

Since the organization of the Federal Bureau of Mines, part of the duties of the field men of the Safety Division has been to teach those connected with the minerals industries how to render the proper assistance to an injured worker between the time of the accident and the time when the injured receives medical attention--in other words, "first aid to the injured." For a number of years after the training was introduced, the response of mine officials and workers was very slow. Many times Bureau instructors devoted at least a week to training 5 to 15 or a few more men. However, in recent years since the companies and the Bureau of Mines have had an opportunity to study the results of first aid training, it has been found that in addition to taking care of an injured worker after an accident and thereby greatly reducing the severity rate, the tendency is for the majority of those who take the training to be more careful in their work, or to be more "safety conscious."

Jan 1, 1938

By Ann G. Kim

The U.S. Bureau of Mines applied its mine fire diagnostic method to an abandoned anthracite mine fire site in Carbondale, Lackawanna County, P A. The technique to locate fires in abandoned coal mines and coal refuse piles includes the determination of hydrocarbon concentrations in mine gases, the imposition of an underground gas flow direction, and use of a surface mapping method, to define heated and cold zones in underground coal strata. The heated zones at Carbondale were characterized by elevated methane concentrations. The results of 25 communication tests were analyzed to define 2 large (approximately 100 by 250 ft) and 5 small, isolated heated zones. An approximate correlation existed between the location of the heated zones and areas of anomalous snow melt. The correlation between the results of the diagnostic? test and subsurface temperatures was not significant.

Jan 1, 2010

By J. F. Barkley

To aid in winning the recent world war, the Bureau of Mines conducted a National Fuel Efficiency Program, directed to commercial plants throughout the Nation, to save greatly needed fuel, a basic resource vital to industrial production. In planning this program it was realized that to accomplish a satisfactory reduction in fuel consumption in any plant, it would be necessary to reach, enthuse, and usually educate to some extent the actual operators of the various types of plant equipment. A major part of the programs consisted, therefore, of visits to plants and work with the operators, including a review with them of their operating conditions and of educational and guiding literature pertinent to the operating problems involved. Through a Nation-wide organization, local volunteer engineers served in making visits to local plants. Each cooperating plant appointed an employee as the "waste chaser," who headed the work of saving fuel in that plant. The educational literature was designed to interest the operator, as well as serve as a guide in eliminating waste of fuel. Volumes have been written on many subjects relating to the saving of fuel. Writings of the treatise type contain considerable good information but do not have wide appeal and probably will be read only by a few studious operators. The problem is not one of getting clown on paper everything that the experts know and would like to have the operator know, but rather to write something that will actually interest the operator and stimulate him to action. Past experience led to the adoption, therefore, of the "quiz-sheet" type of writing, using a quiz sheet of not more than two pages for any principal item. The results obtained during the National Fuel Efficiency Program in many types of plants further demonstrated that the short quiz sheet is satisfactorily appropriate and does accomplish results. Each sheet was prepared and checked by many engineers expert in the particular subject matter of the sheet. Committees of men with much experience in the manufacture and operation of equipment and in the

Jan 1, 1947

By V. F. Parry

The object of this report is to present certain pertinent data on the physical and chemical properties of South Arcot lignite and to present the results of several special tests to show how the raw lignite can be upgraded to superior fuels for certain special uses. The Bureau of Mines Branch of Coal Technology laboratories at Denver have advocated the drying and carbonization of all low-rank fuels for special uses and have introduced and developed new techniques for upgrading and refining noncoking coals. Application of these techniques to the South Arcot lignites was the object of the investigation, and this report presents significant data necessary for planning a fuel program based on utilization of dried and carbonized dusts. In general, the South Arcot lignite is similar in chemical properties to the high-moisture lignites found in the United States and has some physical properties similar to Australian brown coals. The samples submitted for test had lost moisture before delivery to the laboratory, and it has been necessary to estimate the analysis of the lignite in place in the mine. Various observations made in India by qualified technicians indicate that the bed moisture content of the entire seam is in the range of 54 to 56 percent. For estimating purposes in this report, the bed moisture content has been taken as 56 percent and the ash content of the fresh coal as 2.5 percent. The average analysis estimated for the as-mined lignite is: [Moisture percent 56.0 Volatile matter do.22.0 Fixed carbon do.19.5 Ash do.2.5 Heating value B.t.u. per lb. 4,890]

Jan 1, 1957

By L. R. Burdick, J. F. Barkley

The inherent heating value or the amount of heat that will be produced when a coal is completely burned is measured in British thermal units (B. t. u.) per pound of coal . This standard heat unit is the quantity of heat required to raise the temperature of 1 pound of water 1 °F . at about 60 °F . The amount of inherent heat is determined by burning a small quantity of the coal in a heat meter or calorimeter , which gives results in British thermal units . The exact manner of making this test is standardized by the American Society for Testing Materials.4/ The value so determined is the total heat developed by complete burning, with all the products of combustion cooled down to the temperature of the calorimeter . The calorimeter is kept at about room temperature . This total heat is sometimes called the " high" or gross heat value , because it includes the latent heat given up by the water vapor in the products of combustion when the vapor condenses to water in the calorimeter . The heat as measured is reported as the heat of combustion at constant volume , since the burning is carried out in a tightly closed calorimeter chamber whose volume does not change . In actual use , coal is usually burned in an open - end chamber at constant pressure , generally somewhere near atmospheric . As the heat of combustion of coal at constant pressure is very slightly higher than the heat of combustion at constant volume , it might be considered that the heat at constant pressure should be used as the standard reference base . For an ordinary eastern coal the heat at constant pressure is about 16 B. t . u. per pound higher than the heat at constant volume . Calorimeter corrections , ordinarily not considered , that could have been subtracted from the heating value before reporting , may amount to about as much . Hence , the value reported is apt to be more nearly the true heating value at constant pressure than at constant volume .

Dec 1, 1941

By J. A. Pile, Virgil Miller, R. G. Peterson, F. B. Petermann

"INTRODUCTION As virtually no published data are available on the sintering of fine, minus-100-mesh, ferrograde manganese ores, it is most opportune to present data on the amenability of various fine ores and mill products to the sintering process. These data cover the sintering or nodulizing of finely crushed, high-grade pyrolusite and rhodochrosite ores, sintering of manganese carbonate flotation concentrate, sintering or nodulizing the calcine from the deleading of a manganese oxide flotation concentrate, and sintering the calcines made in a Herreshoff furnace from the treatment of manganese sulfate products.If finely sized products are to be smelted in the present electric or blast ferromanganese furnaces, they must be sintered or nodulized. The only specification as to the size of the sintered or nodulized product is that it must pass a 6-inch screen and not contain over 1t-1/2 percent minus 20-mesh material. The minimum-maximum size has not been established. Undoubtedly this opti mum size will be set by the ferromanganese industry when ample quantities of manganese oxide sinters have been smelted."

Mar 1, 1942

By G. W. Grove, E. E. Quenon

"INTRODUCTION During September, October, and November 1946 the Safety Division of the Bureau of Mines, off' the United States Department of the Interior, Pittsburgh, Pa., tested four new types of self-contained breathing apparatus and approved them in accordance with Schedule 13C. Approval was granted with the proviso that certain specifications outlined on the approval plate be made fully effective, and with the understanding that established safe practices in training in the care and use of self-contained breathing apparatus are of major importance.The excellent records made during the past 30 years in the safe use of self-contained breathing apparatus, some of which required the almost continuous wearing of apparatus during several hours daily for days, weeks, or months, may be attributed largely to the Bureau's system of rescue organizations, selection of physically fit rescue workers, effective training, and educational work done in rescue and recovery operations during fires or following disasters and in the care and use of self-contained breathing apparatus. Loss of life during wearing of breathing apparatus was due almost invariably to poorly assembled or otherwise defective apparatus, poor physical condition of the wearer, or insufficient training or some incorrect procedure.The newly developed breathing apparatus are of much simpler design than the conventional type used for the past several years; however, it is just as important to select rescue crews carefully and to train them properly in the care, use, and limitations of the new types of apparatus as for the older long-established types, if anything like safety is to be achieved in using them. The Bureau of Mines considers that 1/2-hour and 3/4-hour self-contained breathing apparatus should be used only as auxiliary equipment in mine rescue and recovery work, and their capabilities and limitations should be well understood by those who wear them."

Jul 1, 1947

By Albert L. Toenges

The Deep River coal field is in Chatham, Lee, and Moore Counties, N. C. The coal-bearing part of the basin is about 35 miles long and 5 to 10 miles wide. Sanford, the county seat of Lee County, is the largest town in the area, with a population of 10,000. Four railroads provide transportation to the area, and four United States highways and improved county roads provide easy access to the field. The Carolina mine at Farmville is the only operating mine in the field. The mine was opened in 1921 by two rock slopes driven from the surface to the Cumnock bed. Mining operations continued intermittently until 1945 and then stopped. In the fall of 1947 the mine was reopened by the newly organized Raleigh Mining Corp.

Jan 1, 1952

By James P. Rider, Charles D. Taylor, Edward D. Thimons

Research was conducted to investigate how ventilation of a mining face is affected when scrubber flow is greater or less than intake flow. Tests were conducted in a full-scale surface test gallery built to simulate a mining entry with a continuous mining ma- chine at the face. Methane gas was released at constant flow at the mining face. Gas measurements taken at six locations near the face were used to evaluate how well the face was being ventilated. Increasing scrubber flow resulted in lower methane levels even when scrubber flow was much greater than intake flow.

By Lloyd Williams

1. The investigation shows that the Coal Creek has been the most productive, bed in Campbell County and contains the largest recoverable reserves of coal. The Pewee, Red Ash, and Jullico have been relatively productive beds and contain appreciable recoverable reserves of coal. The Blue Gem also has been productive in the past, but available information indicates that most of the remaining coal is Less than 28 inches thick. The Big Mary has relatively large reserves over 28 inches thick, but the coal is high in ash and sulfur. Thick partings in the Windrock bed have discouraged mining in that bed. The Poplar Creek and Rex beds generally are below drainage, and large areas have been excluded from the reserve estimate, Reserves in the Walnut Mountain bed will be difficult to mine due to the irregu¬lar thickness and lack of continuity of the bed. Estimated coal reserves are- small in the remaining five beds. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-Foot of coal in place, are estimated to be 398 million tons as of January 1, 1953, o? this total, 267 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, these should be added to the total estimated reserves.

Jan 1, 1956