Search Documents

By Joseph J. Wallace

1. The Pocahontas No. 3 and Pocahontas No. 6 ere the two most important beds in Mercer County from the standpoint of present production and recoverable reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated at 188 million short tons as of January l, 1953. Of this total, 80 million short tons are in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1954

By N. E. Hanna

The effect of small percentages of sodium chloride on the incendivity of permissible explosives was studied by the Bruceton up-and-down technique in gallery tests. Both the reduction in incendivity achieved by addition of sodium chloride and application of the test method to explosives evaluation are discussed. It is demonstrated that the up-and-down technique in gallery testing is suitable for distinguishing differences in incendivity between different explosive compositions and between lots of the same composition. The study also shows that addition of relatively small quantities of sodium chloride tends to reduce the incendivity of explosives to firedamp, but addition of sodium chloride cannot insure reduced incendivity. Any improvement attributable to the salt can be counteracted by undefined variations in the explosive. The need for experimental investigations of a number of factors that may affect the safety of permissible explosives is emphasized. ACKNOWLEDGMENTS Grateful acknowledgment is made of the assistance of Roy L. Grant in analyzing for normality of distribution of the data obtained by the up-and-down methods and to Harold E. Tubbs for numerous calculations.

Jan 1, 1959

By B. H. Eccleston

Experimental work is reported showing the effects of gasoline characteristics on auto emissions. Fuel volatility is shown to influence evaporative losses, with the higher losses associated with higher volatility. Fuel front-end olefin is shown to contribute significantly to reactivity of emissions. Large vehicle-to-vehicle differences were found. The study was conducted by the Bureau of Mines at its Bartlesville Energy Research Center in cooperation with the Coordinating Research Council Air Pollution Research Advisory Committee. The work was done using 15 1968-70 model autos and eight fuels were tested at ambients ranging from 20° to 95° F. Data on emissions from each vehicle-fuel-temperature combination are presented. Also included are calculated photochemical reactivity data and the distribution of hydrocarbon and nitrogen oxides during the test cycle.

Jan 1, 1972

By W. P. Yant

The hazard to health from contamination of air by a noxious gas depends not only on the potential harmful response attending exposure., but also on the warning properties, which in effect may be termed the "accompanying warning response," This warning may be manifested as an odor, taste, irritation of the eyes, nose, or throat, or perhaps headache, vertigo,, or nausea. These manifestations may be painful and even slightly harmful, but to a much lesser degree than the primary injury of exposure. The warning response mitigates hazards directly in proportion to the degree of intolerability which -accompanies injurious exposure, and accordingly its absence augments hazards. This accounts for the fact that the actual health hazards from a nonodorous or non-irritating gas or vapor of comparatively low toxicity sometimes equal or exceed the hazard from a considerably more toxic substance, but one which possesses a marked odor or produces eye, nose, or throat irritation in advance of harmful exposure. When a substance lacks the properties for giving warning, it is often possible to impart them by the addition of a small amount of another substance which has an exceedingly high warning intensity. The vapors of this substance, commonly termed a "warning agent" or "tracer gas," escape and mingle with the gas or vapor which lacks warning properties and thereby apprises persons of the latter's presence. The amount of the warning agent added is that which will give adequate warning in advance of serious physiological harm from the dangerous gas or vapor.

Jan 1, 1930

By M. J. Ankeny

All bituminous-coal mines, by the nature of their product and inherent gassy tendencies, are subject to explosions or mine fires. The evolution from large, hand-loading sections employing numerous men and containing open-type equipment, lights, and nonpermissible explosives to small, concentrated mechanical sections with but few well-supervised men utilizing modern preventive equipment has not altered this premise. Mine catastrophes such as Centralia and New Orient No. 2, as well as recent disasters of less magnitude, have refuted the trend of thinking that modern equipment, will prevent or localize explosions and prevent widespread or loss of life.

Jan 1, 1952

By Fred D. Wright

A drill unit designed by Bureau of Mines engineers for testing various types of rotary bits has been in use since April 1950 at the experimental oil-shale mine near Rifle, Colo. The unit has a hydraulic drill and feed system, which provides the wide range of operating conditions necessary for adequate testing of drill bits and for obtaining data needed for the design of production scale equipment. Through the use of this unit, it has been proved that rotary drilling of vertical holes for mining the benches of the oil-shale mine is much cheaper than percussion drilling, and it is believed that in the near future the rotary drilling of horizontal blast holes in the top heading of the mine will prove equally economical.

Jan 1, 1952

By Harry G. Dosh

Sillimanite, kyanite, and andalusite are aluminum silicates having the same chemical composition (Al2SiO5) and are used in the ceramics industry for the manufacture of high-grade refractories. Natural sillimanite with added corundum or other alumina to just short of mullite (3Al2O3 -2SiO2) proportions is unequalled for jobs wherein strength at high temperatures, resistance to spalling, and resistance to slagging by acid slags are desired. High-grade porcelain ware also requires these minerals. At the same cost, sillimanite would be preferred for most uses, but the lack of any large source of sillimanite bas given economic preference to kyanite or andalusite for special refractories and high-grade porcelain wares. Sillimanite-bearing schists were observed in Spartanburg County, S. C.; as early as 1937 by D. Hoye Eargle, geologist with the U. S. Soil Conservation Service. The mineral was not identified until 1942, when Miss Jewell Glass, of the U. S. Geological Survey, examined several of the deposits. This identification was confirmed in 1943 by Dr. Laurence L. Smith, of the University of South Carolina, when he examined the Spartanburg County deposits and found numerous additional occurrences of sillimanite schist in Greenville County. Subsequent work by the Bureau of Mines and the South Carolina Geological Survey has been responsible for the location of additional sillimanite-rich schist deposits in Spartanburg County. Between October 1, 1948, and November 21, 1948, the Bureau of Mines conducted an exploratory diamond-drilling project on the John Gideon property in the southeastern section of Spartanburg County (fig. 1) and drilled a total of 681.7 feet in six holes. Drilling indicated that the deposit is relatively shallow, as no ore was cut below the zone of weathering.

Jan 1, 1950

By Arnold M. Lansche

Domestic Production.-Domestic production of white arsenic, AS,03, was derived entirely as a byproduct of smelting arsenic-containing copper ores by The Anaconda Company at Anaconda, Mont., and American Smelting and Refining Company at Tacoma, Wash. The Anaconda Company discontinued production of white arsenic in 1965. Arsenic metal was not produced. Consumption and Uses.-Most of the white arsenic produced in 1965 was consumed in manufacturing lead and calcium arsenate insecticides.

Jan 1, 1966

By F. P. Haver

The Bureau of Mines developed a process to extract about 90 percent of the sulfur from molybdenite flotation concentrate by compacting the concentrate with one-quarter of its weight of aluminum powder, heating it at 800° C for 30 minutes, and then allowing the product to react with water. This thermite reduction yields an impure molybdenum alloy plus aluminum sulfide. The latter readily hydrolyzes, to yield pure hydrogen sulfide which can be converted to elemental sulfur by the Claus process. At least 95 percent of the molybdenum can be subsequently recovered as 99.95-percent-pure molybdic oxide.

Jan 1, 1968

By D. B. Dow

The study of oil production methods with reference to the amount of oil originally pressent in the oil-bearing, formations has developed the fact that-ordinary methods-of production remove only a part of the oil actually present. In fact, it is generally realized that when a field is abandoned more oil remains in the sand than has ever been removed. As a consequence of this realization, the petroleum engineer has devoted considerable tine in recent years in devising methods for increasing the percentage of recovery. His studies have indicated that in most cases the total production of a field is dependent upon the available gas rather than upon the available oil. Mien the gas in the sand is exhausted, oil production ceases even though there may be enormous quantities of oil remaining unrecovered. Consequently, any method of conserving the gas or increasing the supply of gas will increase the ultimate recovery from a field. The practice of producing oil under vacuum increases the effectiveness of the gas remaining in the sand, as well as furnishing more gas by evaporating the light fractions of the crude. Pumping ' compressed gas or air down selected wells of a lease has been found to increase the production of oil from the surrounding wells. Studies of oil and gas ratios have indicated that much of the available gas has been wasted as far as its effectiveness on oil production is concerned. his has led to the development of "stop cocking"3 and the practice of producing under back pressure3, which methods aim, to obtain more effective work from the gas with reference to the amount of oil delivered to the well.

Jan 1, 1926

By Charles L. Kimbell

While the statistical summary focuses on 1991 data, this update and outlook section draws on information available to the author as of the date of final preparation in early 1993. For all the press notoriety associated with the shift in the Near East crisis from the defensive posture of Desert Shield to the restoration of Kuwaiti sovereignty through Desert Storm, this was not the dominant event governing global economic thinking in 1991 and the first half and more of 1992. From the global perspective, the momentous political changes in the area that was the U.S.S.R. and in the smaller emerging transitional economy states of Eastern Europe will have even greater current and long-lasting effects on world mineral industry activities than the crisis in the Near East.

Jan 1, 1993

By Lloyd A. Morley, Alan M. Christman

Introduction A wealth of information exists which deals with electrical grounding, both from a general viewpoint and from a specifically mine-oriented approach. Many parameters must be investigated in order to thoroughly cover all of the variables which govern the performance of electrical grounding systems. The emphasis of this work on open-pit practices re- presents a new development in the field of grounding research, and an exhaustive review of the relevant historical documentation is especially desirable. Grounding System Purposes What purposes are served by a grounding system? The answer is four-fold and may be summarized as follows. First, it must limit potential gradients between conducting materials in a given area (56). When a phase conductor comes into contact with a machine frame, current flows through the equipment, which tends to become elevated above ground by an amount equal to the voltage on the conductor. If a man were to touch the machine while he was simultaneously connected to ground in some manner, his body would also tend to become elevated in potential, possibly to a lethal extent. Thus, the grounding system should provide a low- resistance path for the fault current to return to the source. The maxi- mum potential to which a man could be exposed when touching a machine frame is equal to the voltage drop along the ground conductors inside the power cable, as shown in Figure 1 (54). The ground conductors, therefore, (page # 96 is missing from the original document)

Jan 1, 1976

By H. E. Blake

An evaluation was made to determine the economics of utilizing waste fluosilicic acid for production of (1) calcium fluoride, and (2) anhydrous hydro-gen fluoride. Two versions of each process were considered and compared. The evaluation showed that both products could be produced and marketed competitively. Lowest estimated product sales prices required to yield a 25-percent return on investment before taxes (discounted cash flow basis) was $339.34 per ton of hydrogen fluoride and $48.64 per ton of calcium fluoride.

Jan 1, 1971

By Michael D. Fenton

Bauxite resources were primarily in Africa, Asia, Oceania, and South America. Only five countries combined, Australia, Brazil, Guinea, India, and Jamaica, contained most of the total world reserves available for extraction under current economic conditions and accounted for nearly 80 % of world production of bauxite. World bauxite and alumina production declined and prices for smelter-grade alumina remained below the $200/mt level during 1993 because of growing aluminum inventories on international markets and declining worldwide demand. The United States imported bauxite primarily from Australia, Brazil, Guinea, and Jamaica. U.S. alumina plant capacity remained essentially unchanged throughout 1993, but apparent capacity utilization decreased by the close of 1993. Chromium Most of the world's known resources and reserves of chromite are located in India, Kazakhstan, South Africa, and Zimbabwe. India, Kazakhstan, and South Africa accounted for 73 % of world production of chromite. The two largest producers of chromite, Kazakhstan and South Africa, were in the process of major economic and political change during 1993. South Africa's production and exports of chromite continued to fall during 1993, because of weak international demand and a flood of cheap metal from the former U.S.S.R. and China into world markets. Despite a significant increase in production, South Africa's ferrochrome producers continued to operate below capacity in 1993. Prior o the dissolution of the U.S.S.R., Kazakhstan was a major internal supplier of chromite ore to the U.S.S.R. consumer, but subsequent decline in demand led to a downward trend of chromite production in Kazakhstan and increasing exports to Europe during 1992 and 1993. The United States consumed, about 10% of world chromite ore production in various forms of imported materials. The United States imported nearly one-half of its required chromium contained in chromite ore and chromium ferroalloys and metal from South Africa; the remainder was from the minor producers Turkey, Yugoslavia, Zimbabwe, and others.

Jan 1, 1995

By John R. Bitler

A computerized napping system was developed by the Bureau of Mines to provides procedures for the rapid and inexpensive display of coal reserve data. Mapping system output consists of two types of maps, point distribution and contour (isopleth), which can be produced for data (coal analyses) associated with a point location (outcrop, drill core, or mine samples). These locations can be in the form of latitude and longitude or Universal Transverse Mercator (UTM) grid coordinates. The mapping area can range in extent from as small as a single county to as large as a multistate region. The mapping system utilizes programs developed at Harvard University, in addition to several modifications developed by the authors. The primary advantage of this system is that it enables the display of a rapidly changing data base and computerized map generation without the intermediate steps of digitizing and overlaying to produce base maps. The mapping system is applicable to any regional mineral reserve or resource study for which point location data are available. Included are example maps of the distribution of data points and contouring for sulfur content of the Upper Freeport coalbed in this western Pennsylvania demonstration area.

Jan 1, 1977

By Donald I. Kurth

This Bureau of Mines report describes the development and application of a computer model of aquifer hydrology associated with in situ leaching of uranium. The model provides uranium resource developers with a simulation of leachant flow characteristics in a preproduction or pilot five-spot leaching operation. Various types of aquifers are modeled using closed form solutions of the partial differential equations describing the change in fluid head (pressure) as the leaching operation is carried out. User-supplied descriptive input consists of aquifer, well, and leachant flow characteristics. Numeric and graphic outputs such as isopressure, iso-velocity, and isotime contours are available. A typical application is shown.

Jan 1, 1978

By Joseph A. DeCarlo

This publication presents a tabulation of oven-and beehive-coke plants in the United States as well as pertinent statistical data on the number, capacity, kind, and condition of the ovens. Coke is an essential raw material in pig-iron production and the coal-chemical materials produced during the coking process are used to manufacture fertilizers, paints, plastics, synthetic rubber, explosives, detergents, nylon, pharmaceuticals; dyes, and many other products necessary to the high standard of living in this country. In table 1 the oven-coke plants in the United States on December 31, 1959, are listed. This shows the name and address of the company, location of the plant, classification or type of ownership, number and type of ovens, annual coke capacity, and the coal-chemical materials produced. The "furnace" plants I are those owned by iron and steel companies and most of them are integrated with blast furnaces to facilitate transportation of raw materials for steel making. Furnace plants represented 87 percent of the total coking capacity and their average annual capacity was 1. 3 million tons. The "merchant" plants are those associated with chemical companies, gas utilities, as well as those that produce metallurgical, industrial, and residential-heating grades of coke and coal-chemical materials for sale on the open market. These coke plants are smaller than furnace plants and in 1959 their average coke capacity was only 520 thousand tons annually. On December 3l, 1959, there were 54 furnace and 20 merchant oven-coke plants in existence in the United States.

Jan 1, 1960

By S. D. Maksimovic

The Bureau of Mines identified and evaluated major sources of quartz dust during overburden drilling at a surface coal mine, The relative contribution of each source to the total dust hazard was estimated, using personal gravimetric and instantaneous dust-sampling devices. No attempt was made to determine actual dust generation rates. The major sources of dust at the drill rig during dry drilling opera-tions were the collector dump, drill shroud leakage, and drill stem seal leakage, These sources contributed 90 pct of the respirable dust and 89 pet of the respirable quartz dust generated during drilling, The collector dump cycle (21.6 pct of total drilling time) accounted for 38 pct of the respirable dust and 41 pct of the respirable quartz dust, with peak dust concentrations reaching 68 mg/m3. Shroud and drill stem leakage contributed 28 and 24 pct of the respirable dust and 32 and 16 pct of the respirable quartz dust, respectively. A dragline and second drill rig contributed the remaining 10 pct of dust and 11 pct of quartz dust. Gravimetric dust samples collected inside the drill cab and outside, near the cab door, averaged 1.65 and 1.43 mg/m3, respectively, with 6 pct respirable quartz.

Jan 1, 1985

By J. H. Schuenemeyer

Consider a set of points, some of which are anomalous (larger than a specified cutoff value), located on a plane. Whether some or all of these points are clustered to form one anomaly or more or, alternatively whether these points are scattered at random, may be investigated by measuring perimeters of convex hulls. A convex hull is the smallest convex polygon that will encompass a group of points. (Examples of convex polygons are triangles, rectangles, and all other regular polygons.) A set of anomalous points is selected and the perimeters of the convex hulls of this set and all its subsets are measured and compared with tabulated values of perimeters for each subset size. For a given subset size consider those perimeters which are less than the tabulated perimeter. If the number of convex hulls is greater than the maximum number expected by chance, then the chance that any one of the observed-hulls-is a nonrandom cluster is the ratio of the observed number to the sum of the observed and the maximum number expected by chance. Otherwise, the points are evidently not clustered. If many sample points are anomalous, an alternate model defines various configurations of contiguous points and compares the observed number of configurations per unit area with the expected number. Applications are discussed in several fields of geology and geochemistry-including geochemical exploration surveys and heavy mineral spatial distributions--as well as in mining (dust control) and medical geography.

Jan 1, 1972

[ ]

Jan 1, 2012