Search Documents

By Howard C. Turnage, Dana T. Updyke

An evaluation was made of one of several improved underground communication systems sponsored by the U.S. Bureau of Mines. The system evaluated was installed in a typical metal/non-metal room and pillar mine and utilized UHF repeaters connected to a unique distributed antenna and passive reflector system which provided mine-wide communications. A microprocessor controlled data collection system was assembled and installed for the evaluation. Data consisting principally of times and durations of messages and identities of the originating transceivers was collected between February and August of 1982 (6 mos.). Analysis of the data shows that the principal benefits are reduction in time required for unscheduled maintenance and repair, enhancement of safety, and better coordination of production activities. A cost benefit analysis shows a net benefit over cost, although it is also concluded that the capacity of the system is greater than can be justified by current activity in the mine.

Jan 2, 1983

By C. Kwong, L. H. Rorden, T. C. Moore

This report describes the feasibility test of an electromagnetic method for locating, boreholes, with or without casing, that have been drilled in conjunction with mining operations but whose location with respect to the tunnel is not precisely known. The first tests were conducted with the cooperation of the Kerr-McGee Corporation, Church Rock Mining Operations, New Mexico, in September 1977. These tests demonstrated that accuracies of better than ±15% of range and ±1° of bearing can be achieved with a simple system and setups. Subsequent tests, in January 1978, on a horizontally drilled pipe line river crossing application, by Ti tan Contractors of Sacramento, California, demonstrated that accuracies of better than one-half percent of range and a few tenths of one degree of bearing can be achieved by using refined techniques. The demonstration tests were done at ranges on the order of 100 to 200 feet but the method is capable of working at much greater distances.

Jan 5, 1978

By R. V. Ramani, V. T. Burgos, J. A. McClay

Introduction The Cost program was developed to provide the planning engineer with a tool to evaluate the cost implications of the technical mine design decisions. Direct costing methods are employed, where feasible, to provide greater detail and accuracy in the primary cost centers. Options have been provided in the cost computation, economic analysis, and output data subsystems to increase the flexibility of the system. Computer Program The program is written in Fortran IV for use in the IBM System 360/370 computers. i. Main - The main routine reads and stores input data from three sources, user input, Cost Data Library, and data transfer from the Master Design Simulator. Data is trans¬ferred to the appropriate subroutines, as they are called, by means of labeled common blocks. ii. Subroutine CSTCOM - is a data modification routine which computes the peripheral charges related to labor and supervisory costs. iii. Subroutine MANPWR - interrogates section data to determine the total labor and supervisory costs for each cost center. iv. Subroutine CAPCST - computes the total capital investment for each cost center, including the economic life and salvage value of each element. Capital costs are determined by user selection of quantities and models of equipment. Equipment costs are stored in the Cost Data Library for retriev-

Jan 1, 1975

By J. Davitt McAteer

Dear Mine Operator, Training for new employees, refresher training for new employees, refresher training, and new task training can mean the difference between life and death for workers. Part 46 spells out how you can develop a training program to protect workers for on-the-job hazards. Together, labor, industry, and the U.S. Department of Labor reached a milestone with the development and publication of Part 46. We want to continue working together toward the next milestone, October 2000, when the regulations take effect. We want to make sure you have all the information you need about these new training requirements. Throughout the next 12 months, MSHA personnel will be holding regional meetings across the country, delivering information and sample training plans to your operation, and offering you help to develop your plan. If you are among the many operators who are already providing training to your workers, keep up the good work. The rule will tell you exactly what is expected. If you currently have no training program, we can help you develop one. A brochure is being distributed, which highlights the main provisions of the rule. It is designed to introduce the rule to you. More detailed materials will be delivered to you. If you want information right away, simply call us, or e-mail us. We also welcome your comments, suggestions, and success stories. Part 46 will be successful and beneficial to miners through our combined efforts. Together, we can make our mines safe and healthier for everyone. Sincerely, J. Davitt McAteer, Assistant Secretary of Labor Mine Safety and Health Administration

Jan 1, 1999

By R. Blickensderfer

Test equipment that simulated frictional impacts between coal-cutter bits and mineral inclusions at a coal face during operation of a continuous coal mining machine was used by the Bureau of Mines in the laboratory to study the incendivity of impacts between various rocks, metals, and hard-metal alloys in an explosive mixture of air-7 pct natural gas. Quartzitic sandstone was found to be the most incendive of several rocks tested. Limestone concretions from a coal seam, known locally as "sulfur balls," sparked furiously but were not incendive. Among the metals tested, the type of steel used in commercial coal-cutter tools was the most incendive material tested. A l7-4PH stainless steel was less incendive and appears to be the most promising high-strength steel alloy, reasonably economical, for use in coal-cutter bits. Some hard-metal alloys, primarily titanium and zirconium diboride composites, were also evaluated as possible replacements for the conventional cobalt-bonded tungsten carbide used in the tip of coal-cutter bits. The metal-bonded diborides were generally less inc endive but more brittle than the conventional tungsten carbide. Carbonitride coatings on tool bits were also tested but found to have no advantage. The source of ignition during frictional impact between metal and rock was studied. Immediately after impact, a yellow flash was observed and a smear of metal near its melting point occurred on the rock. This hotspot on the rock, rather than the yellow flash or sparks or metal fragments, was observed to be the cause of the ignition.

Jan 1, 1974

By J. Feldman

This report contains a description of the distillation laboratory at Bruceton, Pa., which was established to aid in the separation and identification of the products produced in the synthetic liquid fuel processes under study there. Compounds present in synthetic liquid fuels may include aliphatic from C1 to C60 or greater. Alcohols, ketones, esters, aliphatic carboxylic acids, saturated hydrocarbons, olefins, and diolefins are all found in Fischer-Tropsch products. Coal-hydrogenation products contain, in addition to aliphatic compounds, a large proportion of naphthenic material and aromatic compounds ranging from benzene to coronene; in addition, appreciable quantities of tar bases and tar acids are present. In designing the laboratory, therefore, provision had to be wade for the greatest amount of flexibility and versatility. A great deal of standardization of basic equipment had also to be designed to permit interchange of parts and services.

Jan 1, 1951

By James C. Barker

Gold placer deposits along the upper Yukon River, in the region between the river villages of Circle and Eagle, were investigated by the Bureau of Mines. The investigation was conducted intermittently between 1976 and 1985 as part of an evaluation of mineral resources on lands proposed for inclusion in the National Park System. At least 230,000 troy ounces (tr oz) of gold has been produced in the region, principally from Woodchopper, Goal, and Fourth of July Greeks. The placers are underlain by, or occur downstream of, early Tertiary sediments that have been deposited in the Eagle Trough. Strike-slip displacement along the Tintina Fault is responsible for creation of the trough and may have been a factor in the formation of the present placers. Placers were found to have a close spatial correlation to certain altered fault lineaments of the Tintina Fault trench. Placer concentrates contain several different textural forms of gold, suggesting multiple origins. Geological studies and a survey of 162 panned concentrates throughout the region indicated previously unreported sites of placer gold, and potential exists for the discovery of additional placer and lode gold. Because of nearly continuous soil and vegetation cover, further evaluation of the region will require subsurface sampling.

Jan 1, 1986

By Webster S. Anderson

Two series of tests were run with planer model 'BB": one at the Arickaree mine of the San Francisco Chemical Co., Rich County, Utah, and one at the Roslyn No. 9 mine of the Northern Pacific Railway Co., Roslyn, Wash. The tests at the Arickaree mine were started on June 25, 1958, and continued until September 30, 1958. Prior to these tests, an electrically activated remote-control system was installed, and other modifications were made on the planer. The tests showed that the planer in general and the remote-control system worked very well; however, the various cutting tools used would not consistently penetrate and cut the phosphate rock. This indicated that the cutterhead design had to be changed before the planer would operate efficiently in phosphate beds similar to the "A" bed in the Arickaree mine.

Jan 1, 1962

By David C. Oyler, William P. Diamond

Three long horizontal holes were drilled from a directionally drilled sur¬face hole at the Emerald Mine near Waynesburg, Pa. The purpose was to adapt the technique of directional drilling for use in draining methane from coalbeds. A 504-m (1,652-ft) long, 76-mm (3-in) diam¬eter, circular arc pilot hole was drilled, using a downhole mud motor, to enter the Pittsburgh coalbed at a verti¬cal depth of 305 m (1,000 ft). The hole was reamed to 222 mm (8-3/4 in) and was cased to a measured depth of 486 m (1,595 ft). Three 76-mm (3-in) diameter horizontal drainage holes were then drilled, totaling 2,909 m (9,544 ft) of horizontal hole. Improvements in drilling methods increased the average drilling rate from 20.4 m (67 ft) to 64.9 m (213 ft) per day. The cost of drilling the directional and horizontal holes (using a Government-owned drill rig) was $1,169,530, a figure inflated by inexperience and by delays caused by lost-circulation problems and fishing operations. An estimated total drilling cost of $960,000 (including rental of a drill rig) for an improved system, was determined by a detailed cost analysis. Initial gas and water production from November 1979 through May 1980 was low because of caving of the horizontal holes drilled in shale near the bottom of the casing.

Jan 1, 1982

By Noel N. Moebs

Coal mine roof failure is categorized according to character, trend, or pattern of occurrence. Two principal categories of failure are proposed--geology related and stress related. Geology-related failure includes both lithology and structure. Each of several subcategories reflects the probable cause of failure and thereby provides a basis for the selection of appropriate techniques for reducing the incidence of failure. These control techniques, depending on local conditions, may include supplementary support, destressing, reduction of mine air humidity, or a change in the customary support methods.

Jan 1, 1986

By J. Weinberg

This Bureau of Mines report presents data on the changes in the use of steel in motor vehicles over the past 35 yr. Sources of supply of steel for the automotive sector have shifted from almost all domestic in the 1950's to about 50% domestic and 50% foreign in the 1980's. Downsizing, design changes, and substitution of lighter weight materials to achieve energy efficiency also contributed to the market loss of the domestic steel industry. Although plastics and aluminum have displaced some steel in motor vehicles over the years, heavy low-carbon steel is now being replaced most rapidly by lightweight high-strength steel. If the percent of domestic steel used in motor vehicles had not declined since 1950, domestic industry would have supplied 9.3 million more short tons of steel than it supplied in 1985. Downsizing and design changes accounted for 43% of the loss; steel imports, 32%; and substitution of plastics and aluminum, 25%. In 1985, the total value of market share lost by U.S. steel producers was $5.1 billion, of which $1.6 billion was lost to foreign steel producers and automobile manufacturers. Through aggressive marketing and increased efficiency, however, the domestic steel industry may be able to recapture some lost markets, as applications for high-strength steels expand, and as foreign-owned automotive plants in the United States provide fresh sales opportunities.

Jan 1, 1988

By Ivette E. Torres

For a study such as this, which summarizes and amalgamates much information collected, compiled, and utilized by the numerous U.S. Bureau of Mines country specialists and branch chiefs for inclusion in their country and regional reports that comprise the five other sections of 1992 Minerals Yearbook-International Review, it is clearly impossible to cite all sources of information used in its presentation, but some recognition is due. Generally speaking, this study and its related detailed studies on countries and areas would be much more difficult, if not impossible to complete, without the efforts of the personnel of our counterpart national mining and geological agencies throughout the world. Information that they collect, compile, and then publish, either in their own volumes or those of central statistical agencies in their countries, are the foundations on which this work rests. Thus, our appreciation is expressed to the multitude of persons employed by these agencies for their contributions.

Jan 1, 1994

By James A. West

COUNTRIES of the Near East, with the world's largest and insist prolific petroleum resources, produced nearly 277 percent of the world's estimated total output of crude& oil in 1964 and accounted for about 60 percent of world exports of this commodity. Although petroleum largely dominated the mineral industry of tine area, production of antimony, chromium, copper, mercury, boron, potash, and phosphate rock was of world significance. Production of crude oil in Near East countries reached a record high of 7,520,000 barrels per day in 1964, an increase of nearly 11 percent over that of 1963. Kuwait maintained its position as the leading producer, accounting for almost 28 percent of the area's output. Saudi Arabia, Iran, and Iraq followed with 22.5, 22.2, and 16.5 percent of total area output, respectively. Despite record production, the Near East, proved crude oil reserve remained in excess of 211 billion barrels, or more than two-thirds of the estimated world proved crude oil reserve.

Jan 1, 1966

By Richard J. Kline

This publication comprises tables listing friction loss for a flexible, spiral-reinforced circular ventilation tubing system. The tables were constructed with the following parameters: a friction factor of 62 X 10-10, 10-foot sections of tubing ranging in total length from 100 to 550 feet, air quantities ranging from 1,000 to 15,000 cfm, and one to four 90° bends in the tubing. The aim of this publication is to improve ventilation tubing analysis and to provide a method of proper fan selection.

Jan 1, 1971

By Robert E. Hershey

1. The investigation shows that the Sewanee coal bed is the most important bed in Grundy County arid is the only bed that has had any sustained production. There is no production, at the present time, from any of the other coal beds in the county. The Richland (Lower Sewanee or Coke Oven) coal bed has been prospected but has never been developed extensively. The Angel coal bed has been worked to a very small extent near Beersheba Springs, Tenn., for local consumption. The Battle Creek coal bed has been worked sporadically near Monteagle, Tenn. 2. Known measured and indicated reserves in the Sewaneee coal bed, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 15 millon short tons as of January 1, 1953. Of this total, 10 million tons represents coal 28 inches and more thick. Areas in the bed were omitted from the estimate where available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By R. H. Grau, S. B. Robertson, R. B. Krog, T. P. Mucho

Stone mines represent the highest percentage of operating underground nonmetal mines in the United States. With the introduction of stricter Diesel Particular Matter (DPM) regulations, large-opening underground room-and-pillar stone mine operators are faced with implementing one or more alternative methods to reduce concentration levels including: install and maintain an effective ventilation system; install lower DPM emission diesel engines; the adding of DPM filters. The National Institute for Occupational Safety and Health (NIOSH) is actively researching various aspects of fan and stopping designs in an effort to improve the ventilation of these mines. NIOSH has identified and further developed three alternative ventilation methods for use in large-opening underground mines: split-mine, perimeter, and unit-ventilation. This paper describes the implementation of the three methods with respect to their use in mines of various levels of development.

By J. Schlocker

The present emergency has greatly stimulated interest in the light metals - aluminum and magnesium - owing to their extensive use in airplane construction. The $63,000,000 plant being erected in the Las Vegas Valley by Basic Magnesium, Inc., under the auspices of the Defense Plant Corporation,

Jan 1, 1942

[ ]

Jan 1, 2011

By August J. Kwitowski

This Bureau of Mines report describes how the reinforcement mechanisms of untensioned, full-column resin bolts were determined during one underground study. Both axial and transverse shear loadings were identified for two instrumented resin bolts that replaced standard resin bolts in an opera-ting room-and-pillar mining section. The strain responses of resin bolt steel cores to local axial and transverse shear loadings are described. This information was obtained from laboratory testing of resin bolts installations; it was also used to analyze the data from the underground test.

Jan 1, 1980

By W. R. McDonald

The Bureau of Mines, U.S. Department of the Interior, conducted small-scale field tests on acidic copper tailings as part of its effort to develop, improve, and demonstrate technology for stabilizing mining and mineral-processing wastes. Two successful demonstration revegetation plots were established on an abandoned copper-tailings pond located on public land adjacent to Holden Village, Wash. The tailings were neutralized with treatments of either dolomitic lime or limerock and fertilized with processed sewage sludge and/or commercial fertilizer. Excellent plant growths covering 70 and 24 percent of the surface were achieved on 1/8-and 1-1/2-acre test plots planted in 1973 and 1974, respectively. Regar brame, Tegmar intermediate wheatgrass, and tall wheatgrass provided the best plant growth and surface coverage. The target pH of tailings neutralization was 6.8; however, good plant growth occurred in areas where the soil pH ranged from 2.9 to 5.8.

Jan 1, 1978