Search Documents

By John D. Sullivan

The present article is one of a series which is being prepared by the Southwest Experiment Station of the United States Bureau of Mines in cooperation with the Department of Mining and Metallurgy, University of Arizona, Tucson, Ariz., of papers dealing with factors involved in the leaching of copper ores. A knowledge of the time required to dissolve the various copper minerals present in ores, as well as of the consumption of leaching reagents is very desirable, because with the decrease of the Nation's total tonnage of sulphide ores increasing attention is being given to the recovery of copper by leaching methods from low-grade disseminated ore containing both oxidized and sulphide minerals. As leaching has already been applied with success and profit, this study was undertaken to determine certain fundamental characteristics that are applicable to all ores suitable for leaching.

Jan 1, 1929

By L. C. IlsLey

In the normal operation of mines, the aggregate effect of many seemingly minor op rations may be very important as respects economy and safety. Anion: these operations is the method employed in coupling and uncoupling mine cars. For economic reasons the equipment in mines has not been protected as well as railroad equipment. It is pertinent that haulage accidents rank second in severity among mine accidents, and that manual coupling of cars has been one of the most frequent causes of such accidents. One study4/ revealed that coupling was responsible for about 20 percent of haulage accidents underground. A review of early conditions on steam railroads, which were responsible for the introduction of safer methods of coupling cars, indicates how conditions in might be improved. THE STORY OF RAILROAD COUPLING As any considerable improvement in mine-car coupling probably will follow lines somewhat similar to those that brought order out of chaos for the railroads, it seems appropriate to review briefly the steps taken to improve railroad coupling from the days of link and pin couplings of various types to the adoption of the standard ?M.C.E? automatic coupler.

Jan 1, 1943

By C. J. Cohen, L. A. Dahners

"SUMMARYA method has been developed for surveying, drill holes without lowering into the hole any surveying equipment other than an etch tube. The orientation of the rods at the collar of the hole is maintained as the etch tube is lowered. The attitude of the etch ellipse in depth with respect to the rod orientation at the collar can then be observed. This relationship permits the bearing of the hole in depth to he calculated. The rod orientation is maintained during the lowering by means of a pair of alinement clamps. One clamp is fastened to the top of each rod as the rod is coupled and is removed when the alinement has been transferred to the other clamp at the top of the next succeeding rod. A particular advantage of this survey technique is that surveys can be readily made in magnetic country rock.PRINCIPLE OF THE TECHNIQUEAn axial lamina of the column of drill roes is the lamina in which one fiber would be the centerline of the rods. In the new survey technique, the rods are fed into the hole in such a manner that the axial lamina of each successive rod maintains its position at the collar of the hole. In depth, as the rods bend in following the drill hole, the axial laminae also bend. The lamina that was originally vertical will, in general, be tilted away from the vertical. The trace of this lamina is marked on the glass etch tube before the tube is lowered in the hole. The axial lamina that becomes vertical at the survey station is recognized as that axial lamina which contains the long axis of the etch ellipse. The angle between the lamina originally vertical and the lamina vertical at the survey station is thus measurable. When the vertical axial lamina at one survey station has been determined by the etch ellipse at that station, angle R between this lamina and the vertical axial lamina at the next survey station becomes measurable also. By moans of angle R, and dip angles D1 and D2 at the two stations, the change in bearing (z) of the drill hole between the two stations can be calculated."

Aug 1, 1944

By R. L. Grant

The Bureau of Mines applied automatic computational methods to analyze the degree of correlation between sound transmission and atmospheric conditions. Statistical analysis of data collected over a 5-month period indicated that the following weather variables, listed in order of decreasing importance) have a significant effect on the transmission of sound in the atmosphere: 1. Wind velocity and wind direction. Winds in the direction of travel of the sound wave increase the sound intensity and duration. 2. Barometric pressure. High pressures are related to low sound intensities and durations. 3. Atmospheric temperature. High temperatures are related to low sound intensities and durations. Inversion of the atmospheric temperature did not appear to affect sound transmission under the conditions of this study.

Jan 1, 1967

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1978 and 1979 was 8831.8 million and $336.4 million, respectively. In 1978, nearly all commodities registered an increase in production and value; unit value increased for all commodities, with the exception of native asphalt and sand and gravel. Alabama led the Nation in the production of crushed marble and was second in bauxite, third in masonry cement, kaolin, native asphalt, and oyster shell, and fourth in bentonite, dimension marble, fire clay, and scrap mica. Trend; and Developments.-The Alabama State Docks at the Port of Mobile handled more than 10 million tons of bulk material in fiscal year 1978; volume dropped slightly to 9.8 million tons in fiscal 1979. Bulk materials comprise the major activity at the facility, with iron ore and bauxite being two of the major materials handled. The movement of these ores is vital to the operation of many heavy industries in the State.

Jan 1, 1981

Under the Bureau of Mines Research Contract Number H0252071, Foundation Sciences, Inc. has compared the relative effectiveness of roof bolts installed at an angle over the rib with that of bolts installed vertically at the rib side, The information gathered during this investigation was sufficient to supply supplementary information on the mechanics of roof support systems and the general acceptability of field instrumentation methods. During the 140 days of field investigation, 235 bolts were installed, 45 inclined and 190 vertical, in two adjacent intersections. Of these 235 bolts, 30 were in-stalled with load cells and 38 were tested for anchor capabilities. In addition to this instrumentation, the deformation of the opening was measured by convergence meter on 9 lines throughout the two testing areas, and a borescope and photo-elastic gauges were utilized to obtain information on the roof action beyond the surface.

Jan 1, 1977

By McHenry Mosier

The diamond-drill method was tried at the site selected for driving a 5- by 6 -foot air shaft at the east end of the Bellefonte mine . This method of sinking consisted , first , of drilling a 5-3/4 -inch-diameter cut hole from the surface , then drilling parallel 1.5 - inch ( EX ) holes around it at appropriate distances for a balanced blasting round . The cut hole was not charged with explosive but served as a relief chamber for the incipient expansion of the ground broken by. blasting the surrounding 1.5 - inch holes . The length of each hole was 236 feet , which was the finished depth of the shaft . The nature of the work in the air shaft was largely experimental , and many difficulties arising from the lack of special equipment and proper technique for precise alinement of the drill holes caused expensive delays before they could be overcome . Drilling the 5-3 /4 - inch hole , which was impeded by frequent core blocks in the core barrel , required 10 shifts . average advance per shift for an EX hole was about 150 feet . The The holes were charged and fired from the surface . The length of the section blasted in one cycle was 10 feet . Blasting progressed from the bottom of the shaft upward . The broken stone dropped into a chute , from which it was drawn into cars on the haulage level . The Bellefonte mine is an underground limestone mine.3/ The primary objective in undertaking the research on shaft sinking by diamond drilling was to perfect a method for driving connections between levels of the mine .

Oct 1, 1948

By W. B. Berwald, T. W. Johnson

"The United States Bureau of Mines, in cooperation with the Natural Gas Department of the American Gas Association, has been studying actively for the past several years the flow of natural as through high-pressure pipe lines. 4 This report deals with that part of the study involving the design of pipe-line systems consisting of lines laid parallel to each other. The lines are referred to as the original line and the parallel line. The paralleling lire may or may not extend the entire length &f the original line; however, the parallel line is connected at its two ends to the original line.As a result of the large expansion of the natural-gas industry almost all markets within economic distance, from the developed as fields have at least one pipe line supplying them with natural gas. Small increases in the consumers' demand for natural-gas can be met usually by increasing operating pressures, but any marked increase in demand necessitates paralleling sections of the existing systems. It is believed that to a large extent future expansion in the natural—gas industry will consist of paralleling the present lines. The several formulas given in this report have been developed to aid in the design of such systems. Curves and tables were prepared from these formulas to simplify the calculations materially and to facilitate determination of the sizes of pine to be used in paralleling various diameter lines to give the most economical design. The formulas are presented without detailed derivations, as a complete report on the flow of natural gas through pipe lines is being prepared which will contain the derivations of these formulas. Examples included here show the detail of application of the several formulas to problems of design of parallel lines."

Jun 1, 1934

By D. R. Tesarik, F. M. Jones, J. B. Seymour

As part of safety and stability studies at three underground mines in the United States, researchers installed earth pressure cells and embedment strain gauges in cemented rockfill to measure stress and strain changes as mining progressed and the rockfill was loaded. Data from these instruments were used to calculate the in situ modulus of the rockfill for two of the mines. A three-dimensional numerical model of a cemented rockfill cap was validated with data from extensometers anchored in the mine roof and sill; this model was then used to estimate deformation modulus at the third mine because the earth pressure cells and embedment strain gauges recorded negligible changes. Rockfill binder used at these mines ranged from 4 to 8 per cent of the dry components by weight, the water-to-cement ratio was from 0.42 to1.0, and the largest aggregate size in the three mixes ranged from 5 to12 cm (2 to 4.7 in). The range of the calculated in situ deformation modulus values was large, but as expected, it was bracketed by modulus values for cemented tailings and roller-compacted concrete with similar cement contents and water-to-cement ratios. Dans le cadre d’études sur la sécurité et la stabilité de trois mines souterraines situées aux États-Unis, les chercheurs ont installé des palpeurs de pression des terres et des extensomètres d’encastrement dans les remblais cimentés afin de mesurer les variations relatives à l’effort et à la déformation des terrains durant l’exploitation minière et le chargement du remblai. Les données recueillies à l’aide de ces instruments ont servi au calcul du module in situ du remblai dans deux de ces mines. Le modèle numérique tridimensionnel de la semelle d’un remblai cimenté a été validé à partir des données recueillies par les extensomètres ancrés dans la voûte et dans la semelle de ces mines; ce modèle a ensuite été utilisé pour estimer le module de déformation à la troisième mine, étant donné que les palpeurs de pression des terres et les tensiomètres enfouis avaient relevés des variations négligeables. La matière d’agrégation de l’enrochement utilisée dans ces mines comportait entre 4 % et 8 % des composantes sèches par poids; le rapport eau-ciment se situait entre 0,42 et 1,0; et la taille des agrégats les plus gros dans ces trois mélanges était de 5 cm à 12 cm (2 po à 4,7 po). L’écart entre les valeurs calculées des modules de déformation in situ était grand, mais comme on s’y attendait, cet écart a été compensé par les valeurs modulaires des résidus cimentés et du béton tassé au rouleau avec des teneurs en ciment et des rapports eau-ciment semblables. [Als Teil der Sicherheits- und Stabilitätsstudien an drei Bergwerken in den Vereinigten Staaten von Amerika installierten Forscher Erddruckgeber und Einbindungsdehnungsmesser in zementierter Steinschüttung, um Spannungs- und Dehnungsveränderungen während der fortlaufenden Bergarbeiten und der Belastung der Steinschüttung zu messen. Daten von diesen Instrumenten wurden dazu verwendet, das In-Situ-Modul der Steinschüt-ung für zwei Gruben zu berechnen. Ein dreidimensionales numerisches Modell einer zementierten Steinschüttungsschwelle wurde mit den Daten von den im Grubendach und in der Schwelle verankerten Extensometern validiert; dieses Modell wurde dann dazu eingesetzt, um das Deformationsmodul in der dritten Grube zu schätzen, da die Erddruckgeber und Einbindungsdehnungsmesser nur geringfügige Messabweichungen feststellten. Das in diesen Gruben verwendete Steinschüttungsbindemittel variierte zwischen vier und acht Prozent an Trockenkomponenten nach Gewicht, der Wasser-Zementfaktor betrug zwischen 0,42 und 1,0 und die größte Zuschlagstoff-größe in den drei Mischungen schwankte zwischen fünf und zwölf Zentimetern. Die Reichweite der berechneten Werte des In-Situ-Deformationsmoduls fiel etwas breit aus, aber es fand erwartungsgemäß eine Klammerung der Modulwerte zwischen den Zemen-trückständen und dem durch Walzen verdichteten Beton mit ähnlichem Zementanteil und Wasser-Zementfaktor statt.]

By Thomas C. Ruhe

The Bureau of Mines conducted research to determine the safe operating conditions for using recycled (used) lubricating oil from mining equipment as a partial replacement for diesel fuel to make ANFO-type blasting agents. The use of recycled oil (RO) saves energy, reduces oil imports, and reduces mining costs. Low ambient temperatures may cause these recycled oils to become too viscous for proper absorption by ammonium nitrate (AN) prills and result in poor blast performance, safety hazards, and environmental problems. To help quantify and resolve these issues, viscosity, mixing, and performance tests were conducted at various temperatures. Diesel fuels No. 1 and No. 2 were studied separately and in blends with 25,50, and 75% RO. Good quality ANFO mixes (94-6) were produced with dry absorbent prills and blended fuel (No. 1 diesel plus RO) at temperatures as low as -40° F (-40°C) with 75% No. 1125% RO, and at -20°F (-29°C) with 50/50. Diesel fuel No. 2 also made good mixes as low as -30" F (-34" C) with 75% No. 2/25% RO, and at 0° F(-18° C)with 50/50. Reference detonation velocity tests were conducted in 1.4" (3.6 cm) diameter steel pipe at 70°F (21°C) on No. 1 diesel ANFO (94-6), giving an average value of 9722 ft/s (2964 m/s). Comparison tests showed good ANFO performance at low temperatures. Blended fuel ANFO (75% No. 1/25% RO) mixed, loaded, and tested at -40°F (-40°C), produced an average velocity of 9247 Ws (281 8 m/s). A 50/50 blend gave a velocity of 8083 Ws (2464 ds) at -20°F (-29°C). Based on these results, a practical field method has been developed to help evaluate whether a specific oil blend will mix properly with AN at a low ambient temperature. This method will help to promote the safe and reliable use of RO ANFO at low temperatures, with adequate performance.

Jan 1, 2008

By M. A. Mahtab

This report describes the procedures used by the Bureau of Mines for obtaining attitudes of joints surveyed with a borescope in inclined boreholes. An algorithm for computing the dips and azimuths of the observed joints is presented. The algorithm is used to solve an example problem. A computer program based on the algorithm is listed. It is hoped that the procedures described here will be useful in treating large quantities of data obtained from comprehensive borehole surveys.

Jan 1, 1973

By Alan A. Bergeron, J. L. Michels, R. L. Collins

Advanced communication and monitoring systems were developed and demonstrated in three underground mines representing different mining techniques, geographical areas, and material mined. The first mine was a large coal mine in western Pennsylvania that used room and pillar techniques and continuous mining methods. The system developed for this mine provided private telephone channels, environmental monitoring, and control of underground equipment, all on a single coaxial cable, with all system operations under the direction of a minicomputer. Many advanced features were incorporated into the system, such as paging of roving personnel, two-way section wireless, through-the-earth emergency communication, and redundant signal paths. Television was multiplexed into the system for underground equipment surveillance. A hoist radio system completed the complement of equipment at the mine. The second mine was a magnetite ore mine in eastern Pennsylvania that used block caving mining techniques. A radio system was developed that provided two-way communications between trackless vehicles and roving personnel. A unique system of uhf/vhf repeaters combined with a flleaky-feeder" transmission line offered operational and emergency features not previously found in mine communication systems. Evacuation alarming, personnel paging, fan-hole drill operator communications, and maintenance and safety vehicle dispatch were provided. The system required no dispatcher and operated during power failure. A hoist communications/shaft inspection system completed the installation. The third mine was a deep silver mine in the Cour d’Alene district of Idaho. The system developed for this mine utilizes a single wire pair to provide up to 14 voice channels. A unique combination of PBX, telephone carrier system, and intercoms offered private conversations, selective signaling, and emergency backup communications. Two hoist communication systems were installed to provide a voice link and in-cage belling signal between hoistman and cage.

Jan 11, 1981

By Gary R. Gavan

This report presents the documentation and User's Manual for a data retrieval and report generation computer program. The program operates on a data base containing over 19,000 pieces of coal mine equipment in use in 1976.

Jan 1, 1979

By Daniel G. Di Canio

A computer based accident cost indicator model (ACIM) for estimating tangible costs of occupational injuries, illnesses, and fatalities in the U.S. mining industry is described. Studies performed to expand the scope of the ACIM to all mining sectors are presented. Validation of ACIM cost element estimation algorithms with actual costs of mining-related injuries and illnesses are presented. A study of the effect of a fatal accident on production in surface coal and metal/nonmetal mines is presented. The study is based on a sample of 15 fatalities in underground and surface mines. Evidence of significant long- term decline in postfatality production at 6 of 8 underground samples is presented. The average loss is shown to be 1.8% of annual mine production. A study of accident costs in U.S. mining from 1975 through 1981 using the ACIM is presented. The study shows that total annual costs increased from $180,000,000 in 1975 to $379,000,000 in 1981, a 15% annual increase after adjusting for inflation, with mining companies bearing 45% of the total and expected wage losses to mining families accounting for 42%. The study shows total costs of $12,400 per accident and $674,000 per fatal accident for 1981.

Jan 1, 1983

By Lawrence W. Scott

This report presents several systems for continuously monitoring the quality of air in underground mines that are being developed by the Bureau of Mines. Underground stations measure methane, carbon monoxide and nitrogen dioxide concentrations, air velocity, and air temperature. This information is transmitted over a single telephone pair to central stations located on the surface. The central stations display alarms and the data is selectably displayed on digital panel meters.

Jan 1, 1977

By Harry E. Tuff

"This paper is based data obtained by the Bureau of Mines from some of the principal mine operators in Pennsylvania, in the course of a study conducted in cooperation with the U. S. Forest Service, with regard to economies that might be effected in the selection storage, and preparations of timber particularly treatment with preservative to prolong its life.The Pennsylvania anthracite region, considered as a single mining district is by far the largest user of mine timber of any mining district, either coal or metal, in the United States, and the bituminous districts of Pennsylvania rank second. The present annual consumption of mine timber by the coal-mining industry of Pennsylvania probably exceeds 100,000,000 cubic feet annually.In 1919, Pennsylvania produced, in round figures, 145,300,000 tons of bituminous coal, 86,200,000 tons of anthracite, and 5,400,000 tons of iron ores. If it be assumed that the bituminous coal mines required 0.33 cubic feet, anthracite mines 0.7, and iron mines 0.9 cubic feet per ton mined the timber requirements were bituminous. 47,950,000; anthracite, 60,340,000; iron mines, 4,860,000 or a total of over 113,000,000 cubic feet.The average cost of round mine timber in the anthracite region in 1905, was, according to the U. S. Forest Service, 6.6 cents per cubic foot, and $15.00 per 1000 board feet for sawed timber. The present cost Las advanced to 27.5 cents per cubic foot for round timber, delivered to the mine, of which cost 57.4, represents freight charges."

Nov 1, 1923

By G. T. Brow

An experimental method is described for testing diffusion of gases in crude oils at pressures and temperatures up to 3,000 psia and 200° F. A sampling technique was developed to withdraw by constant-pressure mercury displacement about 60 µl of oil from the diffusion cell through any of several 1/2-in vertically spaced capillary tubes and to trap about 4 µl of the oil in a specially designed microsampler. Oil trapped in the microsampler can be completely inserted in the sample inlet of a chromatograph. From analysis in a three-stage chromatograph (GLC), gas concentration in a sample is determined from the ratio of gas peak heights to area of peaks of reference components (hexanes or heptanes) in the oil. A diffusion coefficient is calculated from measured concentration profiles with known equations for diffusion in finite or semi-infinite systems, depending on whether the gas has or has not reached the end of the oil column. Results are given for a test of methane diffusing at 2,560 psia and 160° F in crude oil from the Weber Sandstone reservoir in the Rangely field, Colorado. A constant diffusion coefficient of 3.34 X 10-5 cm2 per sec was obtained which gives a good fit between calculated and experimental profiles determined at six times after start of diffusion. The maximum standard error of gas concentration determinations experienced with this method was ±0.88 ml per ml of gas-free oil.

Jan 1, 1970

By D. Montagna

Large quantities of zinc-base die-cast scrap containing 3 to 4 percent aluminum are presently refined by mixing with other secondary zinc products such as galvanizer dross and distilling in a retort. The Bureau of Mines investigated alternate aluminum removal processes utilizing low-cost fluxes. Basing the investigation on the metallurgical principle that a reactive impurity can be removed from a less reactive matrix metal by melting under a flux consisting of a salt or oxide of a metal less reactive than the impurity, three separate flux mixtures were studied. In the first flux system, [FeCl3] + NaCI (the active component is underlined), part of the aluminum is' eliminated by the formation of volatile aluminum chloride and the rest by the creation of a high melting point iron-aluminum intermetallic compound that can be separated from the remaining molten zinc by filtration. Aluminum removal in the second system, [Fe203] + CaClz + NaCI, is effected by the formation of the iron-aluminum compound and possibly aluminum oxide. The third system, spent sal skimmings--essentially a mixture of [ZnCl2], NH4Cl, and ZnO, depends solely on aluminum chloride formation. Of the three flux systems investigated, the best results obtained were with system 3. Aluminum was reduced in the molten die-cast alloy from 4.10 percent to 0.01 percent when depleted sal skimmings were used.

Jan 1, 1969

By Donald P. Blasko

The Bureau of Mines investigated two areas of the Alaska Peninsula (Iniskin Peninsula and Becharof Lake) where oil and gas seeps were known to occur in an attempt to determine (1) whether the seeps are still active and (2) the amount of bitumen contained in the drainage leaving the seeps. The oil, water, oil-water, and gas were sampled and analyzed. Five oil samples were taken at four separate oil seeps. The API gravity of the oil ranged from 8.90 to 21.4° and the sulfur content was from 0.12 percent to 0.59 percent. Four of the seven gas samples obtained revealed fair high caloric values, ranging from 746 to 924 Btu/cu ft, and averaging 844 Btu/cu ft. A total of 44 water samples were obtained. Bitumen content of the water was as high as 9,773 mg/l at one seep, but averaged less than I mg/l where the seep-drainage water entered the Gulf of Alaska.

Jan 1, 1976

By Donald N. H. Chi

The unsteady, one-dimensional, compressible-flow equations have been solved numerically for a deflagration propagating through a gallery of finite length closed at the ignition end and open at the opposite end. These equations were solved for two situations wherein (1) the propagating flame was extinguished after 0.1 sec or before the return of aerodynamic disturbances reflected from the open end, and (2) the flame was allowed to propagate a full 0.8 sec until it was extinguished. It was found that the process of sudden flame extinguishment creates rarefaction waves that, upon entering the burned zone, produce resonance within the burned cavity. For the relatively small value of the product of the expansion ratio (8.5) and the effective burning velocities of 7.4 m sec-1 for the first experiment and 4.9 m sec-1 for the second experiment, it was found that the acoustic approximation provides an adequate estimate of the pressures developed ahead of the flame during the system's early history.

Jan 1, 1974