Search Documents

By M. J. Reasor, M. DiMatteo, J. M. Antonini, K. Van Dyke, Z. Ye

"The inhalation of silica has been shown to produce a dramatic inflammatory and toxic response within the lungs of humans and laboratory animals. A variety of cellular and biochemical parameters are used to assess the silica-induced lung injury. The purpose of this paper is to introduce the use of luminok:Jependent chemiluminescence as a new method to study inflammation in both phagocytic cells and lung tissue recovered from silicaexposed animals. Chemiluminescence, or the emission of light, accompanies the release of reactive forms of oxygen when phagocytic cells are challenged. In this study, male Fischer 344 rats were intratracheally instilled with either silica (10 mg/100 g bw) or saline vehicle. One day after the instillations. a marked increase in the chemiluminescence was observed in the lung tissue and bronchoalveolar lavage cells recovered from the silica- treated animals when compared with the saline controls. The light reaction was markedly decreased by either superoxide dismutase or N-nitro-Larginine methyl ester hydrochloride. Superoxide dismutase is involved in the enzymatic breakdown of superoxide anion. while N-nitro-L-arginine methyl ester hydrocholoride, a nitric oxide synthase inhibitor, prevents the formation of nitric oxide. When superoxide anion and nitric oxide react. they form the highly oxidizing substance peroxynitrite. This study then implicates peroxynitrite as an agent that may be responsible for some of the oxidant lung injury that is associated with silica exposure. The use of luminol-dependent chemiluminescence may prove valuable as a method to measure the earliest events in the inflammatory process. and may be an adjunct in studying the mechanisms that produce inflammation. - Environ Health Perspect 102(Suppl 10):37-42 (1994) IntroductionResearch on inflammation has not produced a method that links the initial events of the process to the controlling events. Rather, a variety of parameters are measured that are the result of and not the basis of the inflammatory reaction. Parameters such as tissue weight, edema, blood flow, enzyme and protein release, or production of metabolites (prostaglandins, leukotrienes) have been used extensively. A method is needed that could be applied to cells of a particular type, groups of cells of different types, and even tissue, in an attempt to study the kinetics of the inflammation as well as being sensitive enough to monitor the early events of the process . Since inflammation is so complicated, the relationship between the control of the initial events and the oxidation process has never been explained nor studied in any derail."

Dec 1, 1995

By D. L. Pool

To increase metal recoveries and to minimize pollution by improved extraction technology, the Bureau of Mines investigated a hydrometallurgical technique to recover copper, lead, nickel, and cobalt from lead smelter mattes. The metals were converted from insoluble sulfides to soluble chlorides using a HCI-CI2-02 leaching system. Parameters studied in a 50-gallon, glass-lined reactor were the ratio of hydrochloric acid to chlorine, chlorine consumption per pound of matte, oxygen reaction pressure, and temperature. The matte material used contained, in percent, 19.7 Cu, 52 Pb, 2.9 Ni, 1.5 Fe, 0.38 Co, 0.19 As, 0.41 Zn, and 0.12 Cd. Extraction of Cu, Pb, Ni, Co, and Cd ranged from 92 to 98 pct, with concomitant extractions of Fe and As of <0.1 pct. The Cu and Pb were recovered as electrowon metals, while the Ni, Co, and Cd were recovered as mixed hydroxides.

Jan 1, 1981

By R. H. Sprute

Hydraulic backfill consisting of siliceous mill tailings was successfully dewatered and consolidated by electrokinetics in a field test conducted by the Bureau of Mines at the Star mine, Burke, Idaho. A stope at the 2,000-foot level was filled in such a way that slimes and coarse sand were retained in the scope. Following settlement of solids and decant of surface water, direct current applied between buried electrodes created a firm, dense material in approximately 3 hours. This rapid densification of fine-grained material demonstrated the utility of this method and suggests other applications, particularly in the control of slime deposits that cause serious problems in many deep mines.

Jan 1, 1975

By C. J. Tsai, K. Olson, R. Caldow, B. Cantrell, D. Y. H. Pui

"The amount of new surface generated during fracture of coal and rock has been found to be directly proportional to the amount of energy associated with the fracture. To confirm this and study the relationship between the new surface and dust aerosol formed during fracture the U.S. Bureau of Mines has conducted experiments simulating fracture as it occurs during mining operations. In addition to fracture energy measurements, fragment size distributions were determined over a size range of 0.5 microns to 1 inch. The size measurements accounted for the mass of the original sample. Material studied was Illinois No. 6 coal, coal from the Taggart seam of Virginia, and Berea Sandstone. The experiment employed a chamber to confine sample fracture fragments and a combination of particle measuring systems. Measurement methods included aerodynamic sizing of entrained dust aerosol with optical counting and inertial impaction techniques, physical sizing of non-airborne fragments by sieving, and optical sizing of fragments using optical counting and scanning electron microscopy.Results of the size distribution measurements indicate that a single size distribution law does not adequately describe the entire fragment size distribution. A combination of two size distribution laws, such as the Rosin-Rammler and log-normal distributions, is necessary to describe this size distribution. New surface created by fracture is primarily found 1n particulate between 2 and 50 microns with a mean size of 12 microns. It was also found that the specific energy of fracture can be linearly related to the .concentration of aerosol in this size range.Only a .small fraction, between 0.02 and 0.16 pct, of the dust particles .generated during fracture become airborne. The remainder adhere to the new surface created during fracture. An entrainment fraction, defined for a given particle size is the ratio of the mass of airborne particles to that of the total particles generated in that size range. This experimental entrainment fraction is related to the Van der Waals adhesion force and the electrostatic forces operating during fracture and is used to derive empirical parameters to model these two processes."

Jan 1, 1989

By A. H. Warner, G. A. Morrison

"INTRODUCTION The brown-iron ores of the Western Highland Rim of Tennessee extend north and south across the State for 115 miles. Many prospects of iron ore are known in this area.The district is credited with an output of 8 million tons of washed ore prior to 1930. Records on past shipments of ore indicates that the grade was probably 45 to 50 percent iron, 0,7 to 1.25 percent phosphorus, and 10 to 21 percent insoluble.As part of a survey of the iron resources of the Appalachian area, the Bureau of Manes began exploration .of the Churchwell and Robinette properties April 16, 1945, and continued until July 25, 1945, during which time 122 feet of test pits were sunk and 667 feet of churn drilling was completedPROPERTY AND ACCESSThe Churchweil property and that part of the Robinette tract north of U. S. Highway 64 are reported to be owned by the heirs of William Millsaps.The Churchwell property is northeast of Waynesboro, the county seat of Wayne County (fig. 1), and is east of Forty-Eight Creek, between Duggar Branch on the north and Little Forty-Eight Creek on the south.The property is reached from Waynesboro by traveling U. S. Highway 64 east 8 miles to Forty-Eight Creek, thence north on a secondary road 2 miles, to where Little Forty-Eight Creek joins it, thence by an old logging road up the hill half a mile to the property.The Robinett tract lies 1 mile southeast of the Churchwell and is reached by traveling east from Waynesboro on U. S. Highway 64 and a distance of 6.7 miles, and then turning left on an old logging road and following the ridge 2 miles to the prospect."

Oct 1, 1946

Exposure to airborne respirable crystalline silica dust can lead to silicosis, a debilitating lung disease. On surface coal mining and construction sites, blast hole drills are notorious sources of airborne respirable dust that may contain significant amounts of silica. The drill operator and drill helper usually receive the greatest silica exposure compared with other occupations. As a result, many drilling operations have been, and still are, on more stringent dust standards. Drilling through various rock formations naturally presents a strong potential for silica dust generation for several reasons. First, drilling is a pulverizing process that generates large amounts of very small dust particles. Second, the bailing air used to flush cuttings from the hole leaves the hole at a very high velocity and can be difficult to contain. Third, many fixed shrouds used to enclose the area beneath the drill deck have a significant amount of leakage due to 1) gaps between the shroud and ground created by raising/leveling the drill, 2) gaps in the corner seams, and 3) tom deck shrouds. CONTROLS A dry dust collection system is typically connected to the drill deck to collect dust as the bailing airflow transports the cuttings (and significant amounts of airborne respirable dust) out of the drill hole. Deck shrouds are installed in an attempt to enclose the volume around the drill steel and prevent dust escaping. However, most deck shrouds are rectangular and constructed of four separate pieces of rubber belting attached to the deck. Because of this design, there is usually a significant amount of dust escaping from the open seams as well as the open area between the shroud and the ground. This dust can be a significant source of silica exposure to drill operators as well as other personnel downwind of the drill.

The current procedure for measuring the concentration of respirable coal mine dust is as follows. Each filter is preweighed by the filter manufacturer to ±0.1 mg. Following sampling with the Coal Mine Dust Personal Sample Unit (CPSU) at 2.0 L/min, the filter with coal mine dust is sent to MSHA for weighing. The current MSHA procedure for weighing respirable dust samples uses a Mettler Model AE163 analytical balance in conjunction with an automatic weighing system with a precision of ±0.02 mg [Tomb 19901. Each balance is calibrated twice per day. Quality control for the automatic weighing system includes the systematic weighing of one in eight filters on a second Mettler AE163 balance. Tolerance is set at ±0.1 mg between the two weighings of the same sample. Weights are truncated at the 0.1 mg level (e.g., 3.457 mg is truncated to 3.4 mg) [Bowman et al. 19851. The difference of the two truncated weights is then recorded as the weight of coal dust deposited. The respirable concentration (mg/m3) is computed by multiplying by a correction equal to 1.38 and dividing by the volume of air sampled (2.0 L/min x sampling time [min]).

Jan 1, 1997

Three types of communication systems have become popular in solving communication requirements underground: Loud-speaking pager phones, carrier current phones, and magneto ringing phones. Basically, all three are simply single-channel party line systems. Although these systems are quite reliable, the single channel creates a variety of problems. For example- 1. Since no call is confidential, messages are sometimes purposely made vague, especially if accidents or safety topics are being discussed. 2. A potential user must literally "wait in line" until the channel becomes clear for his use; thus, when foremen have to wait to call in reports or supply requests, this single chan-nel creates a serious productivity bottleneck. 3. In many large mines, there are independent branch lines that must be tied together by a dispatcher, adding further delays to the system. To solve these problems, some mines have installed other phone systems-mostly commercial dial phones in industrial enclosures that offer extra channel capacity and private line features. Others have installed a system that combines both dial- and page-phone features in a single unit. Although these do represent improvements, they do not truly solve the overall problems that face modern mines. Besides extra channels, a communication system should have the following features to enhance productivity and safety: 1. A means of paging a roving miner to alert him that he is wanted on the phone. 2. Wireless-to-wired system interconnects by which a miner can talk on the wired phone system by using a remote portable radio. 3. Remote monitors that alert personnel when there is a toxic or explosive gas buildup. 4. Control interfaces that allow remote control of fans, pumps, or other devices. 5. Transmitters and receivers that can serve as emergency links. 6. Loopback that allows an alternate path of communications if the main path is cut. This chapter focuses on equipment and methods to meet the special communication needs of individuals in various places of the underground mine. The communication requirements can be broken down into four categories: 1. The mine entrance (shaft communication). 2. Permanent and semipermanent locations (shop areas, lunchroom, crusher stations, etc.). 3. Mining areas (the room-and-pillar sections, longwall faces, block caving areas, etc.). 4. Haulageways (tracked trolley haulage, diesel, belt haulage). Methods of implementing systems to meet the communication needs of these areas are described in sections 3.2 through 3.5. Section 3.6 discusses methods of satisfying special communication requirements that exist. Major topics in this category include communications with roving personnel, the isolated miner, and motorman-to-snapper communications. Emergency communication systems are described in section 3.7.Detecting and

Jan 1, 1984

By T. H. Davis

Twelve laboratories from the Western United States and Canada participated in radon progeny intercomparison measurements at the U.S. Bureau of Mines radon calibration facility in March 1987. The participants intercom pared grab-sampling and automated equipment methods at high and low concentrations of radon progeny and condensation nuclei (CN). The objective of this intercomparison was to determine if the measurement procedures and equipment of the North American facilities are equivalent. The sampling results showed good agreement among all participants. The standard deviation for the working level measurements was less than 3.5% for 1.70 working level (WL) and less than 8.8% for 0.21 WL. This relatively good agreement was achieved by using alpha standards calibrated by National Bureau of Standards (NBS) and by closely checking and monitoring airflows.

Jan 1, 1989

By Ann G. Kim

Samples of gas were obtained directly from the coalbed during drilling of horizontal and vertical boreholes in six different formations. The samples were analyzed by gas chromatography for C1 to C5 hydrocarbons and for 02, H2, H2, He, and C02. Methane in the gas varied from 63 to 99 percent; carbon dioxide from 0.1 to 15 percent. The CH4 /CO2 ratio varied and showed no apparent correlation with age, rank, or bed. The majority of samples contained ethane, propane, and butane; hydrogen and helium were found in some samples. Oxygen and nitrogen were usually present, possibly as a result of air contamination. A more extensive sampling program would be necessary to establish relationship between the amount and composition of the gas in the coalbed and other factors.

Jan 1, 1973

By Joan T. May

Anhydrous methods were tested for the extraction of beryllium from low-grade source materials. The purpose of the investigations was to find new extraction processes that are applicable to domestic ores. Beryl, helvite, and phenacite materials containing from 0.1 to 2.8 percent BeO were used as starting materials for direct halogenation tests and pretreatment followed by halogenation. The results of the investigations showed that direct fluorination and carbide-chlorination are two practicable methods that can be applied to low-grade concentrates. Treatment of concentrate-carbon mixtures with anhydrous hydrogen fluoride extracted 99 percent of the beryllium in the concentrate; the soluble fluoride product, converted to an oxide, contained 70 percent BeO. Chlorination of beryllium-silicon carbide, prepared from low-grade concentrates, extracted beryllium into the volatile chloride product.

Jan 1, 1962

By O. Q. Leone

Composite diaphragms were used in the investigation of electrowinning Ti from TiC14 in a fused LiCl-KCI-TiC&apos;2 electrolyte. Composite diaphragms tested were of two general classes--those consisting of two or more solid materials, and those which contained, in addition, a loose material. An electrowinning cell using a flat diaphragm is described. The maximum current density for these diaphragms was 300 amp per ft2. Lower currents permitted longer operation times. The composite diaphragms gave electrode efficiencies that averaged approximately 60 percent, and the electrowon titanium was of good quality--some Brinell hardnesses were as low as 68.

Jan 1, 1972

By W. P. Yant

Canister-type gas masks have become an essential part of the equipment of many industries not only for use in emergencies, but also in performing normal operations of industrial processes and procedures, particularly where ventilation is not practically or economically feasible. They are also used widely for enhancing safety of operations which previous to the development of gas masks had been performed in harmful atmospheres. Since the inception of industrial gas masks the Bureau of Mines has been actively engaged in endeavoring to increase the efficiency and safety of these devices and this bureau has become a source of advice to manufacturers in producing devices of good quality and to industry in the proper selection and use of these devices. In order to give first-hand information and keep current with the demands and needs of industry it is necessary to perform investigations from time to time. This report deals with tests of certain types of commercial gas-mask canisters for protection against mercury vapor.

Jan 1, 1932

By D. W. Frommer, M. M. Fine

Laboratory investigations have produced flotation concentrates contain- ing 91 to more than 92 percent titania, with fair recoveries, from the Christy property, Hot Spring County, Ark. The titanium-bearing ore on the Christy property occurs in a quartz-clay- iron oxide mineralization, which contains, on the average, about 6.0 percent TiO2, chiefly as the mineral brockite; brookite and rutile are different crys- talline forms of titanium dioxide. Recent work by the Bureau of Mines has shown that titanium chloride can be produced readily from the rutile-type mineral by reduction with coke fol- lowed by low-temperature chlorination. Metallic titanium is in turn derived etallic from the chloride by the Kroll process .

Mar 1, 1952

By L. A. Neumeier

The Bureau of Mines evaluated the properties and anisotropy in properties of rolled Zn-Ti and Zn-1.0 wt pct Cu-Ti alloys containing up to 0.36 wt pct Ti. Finish rolling was at varied temperatures to total reductions as high as 92 pct. Alloy properties are very sensitive to various combinations of composition, rolling temperature, and reduction. Properly rolled Zn-1.0 Cu-Ti alloys are superior in strength to Zn-Ti alloys. Conditions are described that lead to best tensile properties. Creep resistance for Zn-Ti alloys decreases with increased rolling temperature when finish rolled to 92-pct total reduction: but not when finish rolled to 33- or 67-pct reduction. Creep resistance for 7n-1.0 Cu-Ti alloys improves with increased rolling temperature to about 480° F. Heavily cold-rolled Zn-1.0 Cu-Ti alloys have fine grain sizes and poor hardness, tensile, and creep properties, but high ductility. Thermal expansivity is markedly affected by the copper addition. Data show the anisotropy of tensile, creep, and thermal expansivity properties. Large idiomorphic crystallites of TiZn15 appear in both Zn-Ti and Zn-Cu-Ti alloys when more than about 0.2 pct Ti is present. A new Zn-Cu-Ti intermediate phase was also identified. Empirical equations are presented relating creep rates with major process variables.

Jan 1, 1971

By A. L. Engel

Included in the program of the Rare and Precious Metals Station, Metallurgical Division, Bureau of Mines at Reno, Nev., are investigations of treatment methods for ores representative of various mining districts throughout the country. The samples received for this work may come from areas only recently explored or from newly discovered ore deposits in older mining districts. The present investigation deals with a case of the latter type, the. ample having come from a section that has a past record of considerable precious. metals production. The application of current treatment methods to this type of ore seems to offer excellent possibilities of satisfactory economic results. Definite identification of the silver mineral in this ore asthe chloride cerargyrite, AgCl, adds considerable interest to, the investigation, as in many cases where silver occurs in comparatively small amounts in an ore it is not possible to identify the particular mineral carrying the silver or else it is contained in or combined with other more common minerals. Cerargyrite is the "horn silver" of the bananza period and is mentioned in many accounts of pioneer mining of high-grade ores The occurrence of this mineral in finely disseminated form it a low-grade ore is believed to be unusual. The sample investigated was obtained from the&apos; Bullfrog District neat Beatty, southwest Nye County, Nevada. The ore contained 16.7 ounces of silver per ton of ore, 0.007 ounce gold, and 0.32 percent copper in a silicious gangue, with accessory minerals, including iron oxides and scorodite; the hydrous iron arsenate.

Jan 1, 1949

By Leslie H. Sharp, Martin J. Gavin

Those of the oil-shale operators in this country who are sincerely attempting to make a real industry out of oil-shale developments, are anxious to obtain fundamental data on the retorting of oil-shale; particularly as regards the effect of certain variable factors in the process of retorting on the quantity and quality of products yielded from oil shales when they are subjected to destructive distillation. From careful examination of a con siderable number of suggested processes for treating oil shales and the con flicting ideas on which they are designed, it seems probable that accurate information of a fundamental nature is highly essential to the successful establishment of an oil-shale industry in this country. . Accordingly, the United States Bureau of Mines, in cooperation with the State of Colorado, is undertaking to furnish some definite and impartial information of this type through investigations now under way at the University of Colorado, Boulder, Colo. A retort for the distillation of oil from oil shale has been designed and installed, together with the necessary auxiliary equipment for controlling and determining variable factors of distillation, and for recovering and de termining the quantity and quality of the products yielded from the shales. The retort is of such a nature that conditions of retorting can be accurately . and completely controlled, and varied at will. It is not designed as a com mercial retort, but only for research purposes. A testing laboratory with equipment necessary for the examination of the shales, physically and chemic ally, and the products yielded by them, has also been fitted up . The material used in the investigations is oil shale obtained from the DeBeque, Colorado, shale field. It yields on distillation in the Bureau of Mines testing apparatus, about 42 gallons of oil to the ton, and is there fore a fairly representative sample of the shales that probably will be first worked in Colorado. The shale used will be as uniform as possible in character and oil yield and will all be obtained from the same seam at the same point, in order to avoid the introduction of unnecessary variable factors in the tests and to render results strictly comparable •

Jul 1, 1920

By G. S. Rice, H. P. Greenwald, H. C. Howarth

"Stoppings in coal mines serve, important and. vital functions, such as coursing the ventilating current, sealing off abandoned or dangerous workings, sealing fire areas, and separating mines at boundaries. Stoppings may hold back water, but normally that is not their function; their design is, or should be very different from that of a hydraulic dap which is designed to a definite load, often a very heavy one, from one direction over an indefinitely long period. Hence, a dam usually requires an arched structure to resist hydraulic pressure, and it must be massive to meet vertical stresses due to heavy ground pressure.Stoppings are designed primarily to resist a pressure applied laterally through air or gases. Their strength cannot be stated without specifying the direction of applied load. A stopping may be placed in stress by proof pressure subsequent to erection, through extraction of pillars in the vicinity which may act direct, or by squeezing the ribs or heaving the floor. These forces act more or less parallel to the faces of the stopping and may be very great but measures must be taken suitable to each case, and it is impossible to allow for these in general specifications other than to call for normally good construction. A stopping is principally designed to resist the action of forces at right angles to its face, such as the shocks of blasting, the pressure of gas from instantaneous violent out bursts such as have occurred in certain British Columbia coal mines, sudden compression of the air by great falls of roof in closed spaces, and at time pressures that accompany an explosion of either fire damp or coal dust or both. This paper deals with the tests of pressures of explosions only."

Sep 1, 1930

Pillar design is the first line of defense against rock falls—the greatest single safety hazard faced by underground coal miners in the United States and abroad. To help advance the state of the art in this fundamental mining science, the National Institute for Occupational Safety and Health organized the Second International Workshop on Coal Pillar Mechanics and Design. The workshop was held in Vail, CO, on June 6,1999, in association with the 37th U.S. Rock Mechanics Symposium. The proceedings include 15 papers from leading ground control specialists in the United States, Canada, Australia, the United Kingdom, and the Republic of South Africa. The papers address the entire range of issues associated with coal pillars and have a decidedly practical flavor. Topics include numerical modeling, empirical design formulas based on case histories, field measurements, and post failure mechanics.

Jan 5, 1999

By Bernadette Michalski

Although hydrocarbons accounted for more than 60% of Bahrain&apos;s income and more than 80% of export earnings, this island nation sustained one of the more diversified economies in the Gulf Region. The availability of low-cost natural gas for electric power has fostered the development of a significant aluminum refining and manufacturing industry with emphasis on vertical integration. The Bahraini iron pelletization plant, closed since 1986 due to financial problems, was scheduled to reopen by early 1989. Commodity Review Metals.-Aluminum.-Aluminium Bah-rain Bsc (Alba) attained record high production levels in 1988 taking advantage of favorable aluminum prices, which averaged over $2,000 per ton as compared with less than $1,500 per ton in 1987. Net aluminum production was nearly 13,000 tons over design capacity. Fewer standard ingots (52,081 tons as compared with 79,685 in 1987) were produced as Alba concentrated on higher value added products such as rolling ingots (42,324 tons as compared with 32,125 tons) and extrusion billets (60,934 tons as compared with 46,618 tons).

Jan 1, 1990