Search Documents

By James R. McVey

A new method for measuring deformations of rock surfaces in underground excavations has been suggested by Dr. James Powell of Brookhaven National Laboratories (BNL) and subsequently developed and successfully demonstrated in a mining environment by the Federal Bureau of Mines, Spokane Mining Research Center (SMRC) and Brookhaven National Laboratories. The system uses 35-mm photography of targets strategically located on surfaces of interest, such as across the roof and on the sides of a mine drift or tunnel. The optimum tar-get, as determined in this investigation, consists of a white ?X? made with 1/8-inch-wide reflective tape on a black 6-inch square. Photographs, taken in pairs from two separated camera positions and at regular time intervals, were analyzed at the Bureau by hand and at Brookhaven National Laboratories using techniques and equipment similar to those used in cloud chamber film analysis. Test results show that deformation-measurement accuracies of better than ±0.020 inch in a drift that is 20 feet wide can be expected. This degree of accuracy, plus providing displacement data in the X, Y, and Z directions (rather than the one direction formerly possible), makes this a noteworthy and useful tool for industry as well as for mining research.

Jan 1, 1974

By W. P. Diamond, B. M. Bench, C. M. McCulloch, Maurice Deul

As part of the Bureau of Mines methane control program, the Pittsburgh coalbed was studied in Washington and Green Counties, Pa., and in Marion and Monongalia Counties, W. Va., where this coalbed is now being mined at its greatest depth. The coalbed thickness appeared to be structurally controlled; the bed was generally thinner near the axes of anticlines and thicker near the axes of synclines. The overburden isopach shows a similar relationship. Most of the clay veins in coal occur in the synclinal troughs, generally under sandstone roof. Cleat orientations measured in 18 underground mines showed that face cleats are perpendicular to the axial trends of the folds, and the butt cleats are parallel to the axial trends, indicating structural control of the cleat. Measurement and analysis of surface joint orientations provide a method for predicting the cleat orientations of the coalbed, but linears measured from infrared photographs and photoindex sheets helped only to determine regional trends. The results of these investigations provide a geologic framework for rational planning for underground mine development to use the best available technology to cope with methane emissions, coalbed discontinuities, and related ground support problems.

Jan 1, 1975

By M. Howard Berliner

The Harding pegmatite dike is well known for the production of spodumene and lepidolite in the period 1920 to 1930. It attained greater prominence during the last war by being the largest producer of domestic tantalum ore from the rare mineral microlite. The deposit is believed to be the only proved reserve of tantalum ore in the United States today. In 1943 the main portion of a large tantalum-bearing zone in the Harding dike was developed by the Bureau of Mines with the assistance of the Federal Geological Survey. Analysis of this zone from 39 diamond drill holes and quarry exposures showed a large deposit containing 2 pounds of microlite per ton and 21 percent spodumene, In September 1948, the Bureau of Mines resumed development of the deposit with a view to extending the tantalum-bearing zone farther to the southwest or delimiting the ore body. Seven diamond-drill holes failed to penetrate the ore zone in its southwestward projection, Much of the following general information is summarized from the report on the first exploratory work of the Bureau of Mines by John H. Soule.2/

Jan 1, 1949

By George S. Rice, J. W. Paull, R. R. Sayers

"Standard rock dust for use in the rock dusting of coal mines might be defined tentatively as powdered mineral, light colored and free of carbonaceous matter and free silica, all of which will pass a 20-mesh screen while 50% of it will pass-through a 200-mesh screen.Such dust may be prepared from limestone, gypsum, anhydrite, or shale free of sand and flint. For the initial rock dusting of the average nongaseous bituminous mines enough standard rock dust should be applied so that the combustible content of the resulting mixture of rook dust with mine dust shall not exceed 45%, a range somewhere between 35% end 45% being the practical objective sought.All entries, slopes or passageways and room necks should be rock dusted.Additional safeguards are:a.,Rockdusting roomsb.,Scattering of dust in vicinity of shots before firing.c.,Placing of barriers in the mouths of panels, cross-entries and other key positions.Redusting becomes necessary whenever the combustible content of the mine dust exceeds the permissible maximum. This should be determined by regular, systematic sampling, followed by a simple analysis of the samples for combustible content. A Bureau of Mines volumeter for measuring the density can be used for the determination of combustible content."

May 1, 1924

By P. C. Van Natter

Numerous mine fires have resulted in high death tolls and considerable finan¬cial loss during the history of coal mining. In most instances the death toll and financial loss were greater because of inadequate fire-fighting facilities. The information in this report is presented in the hope it may serves as a guide in the selection, placement, and care of fire-protection systems in similar coal mines. The adequacy of fire protection varies according to size of operation, employment, and production. When fires occur on the surface or underground, measures must be applied quickly to prevent incipient fires from spreading. The record of coal-mine fires shows that, in many instances, facilities for combating fires were very meager or were absent. It would be virtually impossible to establish and maintain all the necessary facili¬ties that may be needed to extinguish widespread mine fires, but it is believed that the coal industry can ill afford less than the minimum required by other industries where the time element and avenues of escape are much more favorable.

Jan 1, 1958

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

The Federal Coal Mine Health and Safety Act of 1969 has dictated major changes in mine ventilation with regard to both air quantity and quality. Requirements have also been placed on the ventilation of beltlines, gob and face areas, and air velocities on trolley haulage roads are limited. Escapeways, separate from trolley haulage roads and on an intake split of air, must be maintained continuous to the surface. These and other similar requirements have not only precipitated several modifications to existing ventilation systems but also have greatly increased the complexities of new mine ventilation planning. It is apparent that the use of computers in ventilation system analysis and design is a necessity. SUMMARY Although computer oriented analysis of mine ventilation systems was introduced over two decades ago, it has yet to receive widespread acceptance in the United States. Central to this problem is the fact that, while many computer programs for network analysis have been developed, no attention has been paid to the development of computer input data. Consequently, without this foundation, program applications have been infrequent. This thesis has directly attacked this problem and has presented all pertinent information basic to the development of good computer input data. The areas that were covered include quantity measurement, pressure measurement, fan testing, survey data balancing, and the development of a network schematic from the ventilation survey results. These discussions on data collection and the corresponding reduction to computer coding have been illustrated by an application of a ventilation simulation program to an existing mine in Southwestern Pennsylvania. The use of a ventilation

Jan 1, 1977

By L. C. IlsLey

"There are two general classes of accidents that prevail in and about mines, namely - (1) those that through the nature of mining work can only be lessened, and (2) those that by proper precaution can be eliminated altogether. Explosive accidents that ordinarily take place while explosives are being transported in and about mines belong to the second class, that is, by proper care all such accidents can in general be avoided.The following table gives a brief summary of several accidents and disasters that have occurred in the United States and indicates the need of universal preventive measures as a basic part of all State regulations.ACCIDENTS AND DISASTERS OCCURRING WHILE TRANSPORTING EXPLOSIVES.***"

Sep 1, 1923

By D. F. Scott

The purpose of this study was to determine if miners were at risk from exposures to chemicals used in the mining industry and determine the nature and sources of the illnesses and injuries. The U.S. Mine Safety and Health Administration?s (MSHA) employment and accident, injury and illness database was reviewed. There were 2,705 cases of chemical-related injuries and illnesses reported from 1999 through 2006, involving 66 different chemicals. The main source (cause) of chemical-related cases was acids/alkalis (about 39%). The primary nature (effect) of chemical-related cases was chemical burns (about 57%). The job classification where workers incurred the most chemical-related injuries and illnesses was cleaning plant operator/media operator/boney preparation plant operator/crusher worker (cleaning plant operators are responsible for maintenance of plants, media operators are responsible for handling reagents, boney preparation plant operators oversee removal of ?bone? from coal, and crusher workers use large crushers to break mined material). From 1999 through 2006, the rate of ?nonfatal days lost? and ?no days lost? (resulting from injuries) did not change significantly; however, the rate of illnesses decreased significantly. Chemical burns accounted for a large number of injuries; mining companies should carefully examine their personal protective equipment (PPE) requirements, training methods and safety culture to ensure that their workers are protected.

Jan 1, 2009

By Wilbert J. Huff

The Explosives Division of the United States Bureau of Mines makes certain laboratory and field investigations that deal with explosions, explosives, ignition, and combustion, together with many related problems, such as the cause and prevention of fires, and certain fundamental scientific questions bearing upon the determination of the chemical and physical mechanisms underlying some of the important phenomena encountered. Its work on explosives has been particularly directed toward determination of the chemical and physical characteristics of explosives designed for use in coal mines and in a more limited way to those used in metal mines, tunnels, quarries, and other engineering operations. This testing is handled by two units of the Explosives Division, as follows:

Jan 1, 1937

By G. W. Birge

The Bureau of Mines investigated the effect of temperature on the mechanical strength of cokes of the type normally used in blast furnace operations. Eight samples of industrially produced cokes were subjected to ASTM tumbler tests at temperatures as high as 1,100° C (2,012° F); these temperatures had no significant effect on tumbler results for cokes with stability indexes of 40.6 to 59.9. Two foundry cokes which were tested at only one elevated temperature (900° C) decreased slightly in tumbler stability. Iron are pellets made from a variety of ores and by various industrial methods were not significantly affected by temperature when tested in an oxidizing atmosphere at 1,000° C (1,832° F) by the tentative standard ASTM method.

Jan 1, 1966

By D. A. Reynolds

The Bureau of Mines-American Gas Association survey of the carbonizing properties of American coals was begun in 1929, and has been continued almost without interruption since that time. Upwards of 100 coals have been carbonized at low, medium, and high temperatures in this survey, and about 200 additional coals have been carbonized at high temperatures only. All survey coals were blended with coal of different rank for carbonization at one high temperature (900° C,). During the past few years, 12-high-volatile A coals were blended with Pocahontas No 3 coal from Kimball, McDowell County, W. Va., and in this report the physical properties of the cokes from these high-volatile coals and their blends are compared.

Jan 1, 1949

Improve transmission of data from an underground mine monitoring system to a remote, mass-data storage system. Background Instrumentation systems in underground mines must operate under environmental extremes of dust and humidity, local electromagnetic/radio frequency (EM/RF) interference fields, and potentially explosive atmospheres. During a recent roof-bolt study performed by the Bureau of Mines, it was necessary to transmit a large quantity of data to a data storage system. Conventional wire cable transmission presented several limitations which often required special electrical isolation or physical protection. Because conventional wire cable presented certain problems, the Bureau of Mines investigated alternative means of data transmission. The research investigation led to the selection of fiber optic cable for data transmission applications. The fiber optic method of data transmission offers several advantages: ? Since the transmission medium consists of light waves, it is safe to use in gassy mines. Where applicable, MSHA permissibility standards for peripheral devices must be met. ? It is lightweight and rugged. ? It can operate up to 131000 feet (4km) without repeaters and without EM/RF field interference.

Jan 1, 1986

By T. R. Strombotne

The purpose of this report k to document a contract undertaken by TSA Systems, Incorporated for the United States Bureau of Mines to develop a commercially available source of a continuous, working,, level detector for the measurement of radon daughter products in various working environments. The basic radon measuring technique was devised by Robert Droullard and Robert Holub and has been applied here. For further details or purchasing information contact: TSA Systems, Incorporated 4919 North Broadway Boulder, Colorado 80302

Jan 1, 1982

By Roy L. Wilfong

The linear expansion of high-purity oxides of yttrium, cerium, samarium, europium, and dysprosium was determined by the interferometric method for the temperature range 25° to 1,000° C. Single-crystal magnesium oxide and single-crystal aluminum oxide were used as reference materials. The bulk density and crystal form of the nonreference materials also were determined. The coefficients of linear expansion in the range 25° to 1,000° C were found to be 8.10 x 10-6 for yttria, 12.10 x 10-6 for ceria, 10.81 x 10'6 for samaria (monoclinic), 10.35 x 10-6 for europia (monoclinic), and 8.13 x 10-6 for dysprosia, each given in centimeters per centimeter per degree Centigrade. A detailed investigation of the interferometric technique for measuring thermal expansion in this temperature range was made. The interferometer was found to be a precise tool but only when adequate precautions were taken. These precautions are described.

Jan 1, 1963

By James E. Hill

In the course of exploratory drilling during World War II by the Bureau of Mines under the Strategic and Critical Minerals investigations Program, a problem arose as to the ultimate disposal of the drill core resulting from that program. The difficulties experienced in obtaining factual information to evaluate mineral deposits examined (during that program) influenced the Bureau in a decision to catalog and store the drill cores for future reference. Initially, the drill cores were stored at the nearest Bureau of Mines station that had space available for the purpose. Recently the Bureau stations at Minneapolis, Minn., and Denver, Colo., were designated as the locations of permanent drill-core storage facilities. Drill cores that are retained from Bureau of Mines mineral-exploration projects are stored at these two locations and are given preference in selecting cores for storage. Drill cores are accepted also for storage from other Government agencies, State agencies, private companies, or individuals on the basis of available facilities and consistent with the significance of the core in relation to Bureau of Mines objectives and national interest. Selection and acceptance of such drill core are determined by the Bureau of Mines. The drill cores stored at the two locations are available for inspection by any person having a legitimate interest in the mineral deposits represented by the cores. Approximately 1,850,000 feet of drill core can be stared in the facilities now available to the Bureau of Mines. Approximately 475,000 feet of drill care is stored or scheduled for storage at Minneapolis, Minn., and 240,000 feet of core stored or scheduled for storage at Denver, Colo. A list of drill core now in storage at the Bureau of Mines core-storage facilities at Denver and Minneapolis is included as appendix A.

Jan 1, 1957

By M. Kanda, W. D. Bensema, J. W. Adams

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating hardrock mine, Grace Mine, located near Morgantown, Pennsylvania. Diesel-powered haulage equipment is used in this mine, and the electromagnetic noise environment it creates was measured to see how it differs from the environment created by electric-powered haulage equipment. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. Data are recorded using broadband analog magnetic tape and are later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific measured results are given in a number of spectral plots and in amplitude probability distribution plots.

Jan 6, 1974

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

B 5 Typical Input - Ouput The input data and the printed output for case 8 of the simulations (Section A.4) are shown in the following. The branch, level, node, miner and hoist numbers mentioned in the input and output refer to the corresponding numbers in Figures A-3, A-4 and A -5, The plotted ouput, already shown in Figures A,11 and A-12 is not repeated. The input data shown does not include the following simulation parameters: DTIME = 0, 05 FTIME = 130 JPLT(K) = 1 for K = 1, 2, 3 0 for other K TPLSTR = 0.0 TPLST P = 130

Jan 1, 1976

By K. R. Becker

The addition of a force gage and a reaction detector to the Bureau of Mines drop-weight impact apparatus made it possible to examine the details of the force exerted on the specimen and make estimates of the time to reaction. With the current setup the force was found to be oscillatory and not reproducble. However, single well-defined pressure pulses can be delivered to the explosive sample by modifying the drop-weight tools. With a modified test arrangement, the time to reaction and the peak force and energy at the time of reaction were determined as a function of drop-weight height for several different explosives. All these parameters were found to decrease as the rate of force application was increased. The same parameters were also found to vary with the thickness of the test sample. The implications of these results are discussed in terms of practical drop-weight testing.

Jan 1, 1972

PURPOSE: Evaluate practical technological advances in level-dependent hearing protectors and inexpensive personal acoustic monitors. RESEARCH SUMMARY: The results of previous NIOSH research show that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals and that miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and gender. Using hearing thresholds at 4,000 Hz as an indicator, coal miners experience hearing loss 2.5 to 3 times greater than would be expected for persons not exposed to occupational noise. At age 50, 90% of coal miners and 49% of metal/nonmetal miners were found to have a hearing impairment. In comparison, only 9% of a nonoccupationally exposed control group had a hearing impairment at age 50.

Jan 1, 2000

By A. R. Taylor

Using solution calorimetry, the following heats of reaction were determined: (1) NaCN(c) + 1/Cu20(c) + 129H20(l) ? CuCN(c) + NaOH?128.5H2O ?H = -13.44±0.10 kcal/mole, (2) HCN(2) + NaOH?128.5H20 ? NaCN(c) + 129.5H20(l) ? = -2.52±0.02 kcal/mole. From these reactions, the heats of formation for CuCN(c) and HCN(2) were calculated to be 22.7±0.4 kcal/mole and 24.9±0.4 kcal/mole, respectively. Reaction 2 was made to check the consistency of literature values for heats of formation of HCN and NaCN. Adiabatic calorimetric measurements between 10° and 400° K showed the entropy and heat capacity of CuCN(c) to be 21.51±0.06 eu and 14.58±0.04 cal/mole deg, respectively, at 298° K. A broad anomaly in the heat capacity was found in the temperature range 285°-320° K. The heat of transition associated with this anomaly was less than 1 cal/mole, the sensitivity of the measurements.

Jan 1, 1971