Search Documents

By Albert L. Brautigam, Michael C. Leigh, August J. Kwitowski

The U.S. Bureau of Mines developed and tested a teleoperating system to control a new highwall mining system. A remote operator was provided out-of-sight sensory information and control of coal extraction and haulage equipment. Surface and production testing proved that the teleoperating system supplied the operator with sufficient sensory information to operate the mining system. Details on the teleoperating system provided in this report include (1) sensor selection, (2) a description of the electronic control system, (3) equipment selection and modifications, (4) the positive test results, and (5) recommendations for system improvements.

Jan 1, 1992

By Paul R. Amyotte, Omotayo Kalejaiye, Kenneth L. Cashdollar, Michael J. Pegg

The Siwek 20-L chamber is widely used throughout the world to evaluate the explosibility of dusts. This research evaluated the quality of dust dispersion in the Siwek 20-L chamber using Pittsburgh coal, Gilsonite, and purple K dusts. A Pittsburgh Research Laboratory (PRL) optical dust probe was used to measure optical transmittance through the dust cloud at various locations within the chamber. A total of 540 tests were performed, with triplicate tests at five nominal dust concentrations and six locations. The two standard dispersion nozzles (rebound and perforated annular nozzle) were compared. The transmissions corresponding to the normal ignition delay period were used to: (a) determine variations in spatial uniformity of dispersion obtained with both nozzles; (b) make comparisons between the experimental transmission data and those calculated from theory for the three dusts; and (c) make comparisons with transmission data measured in the PRI, 20-L and Fike 1 -m3 dust explosion chambers. The uniformity of dispersion for the three dusts was similar with both nozzles, despite the differences in nozzle geometry and mode of operation. Transmission data of the three dusts were all significantly lower than those calculated from theory. This was discovered to be, in part, due to significant reduction in particle size that occurred during dispersion. By measuring particle sizes before and after dispersion, values of 60%, 50%, and 20% reduction in particle size (based on the surface weighted mean diameter) were obtained for Pittsburgh coal, Gilsonite, and purple K, respectively. Transmission data from the PRL 20-L, Fike 1 -m3 and the Siwek 20-L chambers indicated comparable results in terms of uniformity of dispersion. However, transmission data from the Siwek 20-L chamber were significantly lower than those of the PRL and Fike chambers. Again, this was attributed, in part, to the significant reduction in particle size that occurred during dispersion in the Siwek chamber. The design of the outlet (dispersion) valve of the Siwek 20-L apparatus charge vessel was largely responsible for the particle break-up. The contribution to particle break-up by the dispersion nozzles and the high level of turbulence in the chamber were found to be minimal. This is a significant finding in that the dust particle size tested for explosibility in the Siwek chamber is considerably smaller than the original dust sample.

By William J. Campbell

The possibility of chemical analysis by identification of characteristic X-ray spectral lines was first suggested by H. C. J. Moseley in 1913.3/ For a given spectral series it was found that the frequency of the characteristic radiation was proportional to the square of the atomic number of the excited atom. Siegbahn and his coworkers improved the instrumentation and accurately determined the wavelengths of the characteristic spectra for most of the elements .4/ In fluorescent X-ray spectroscopy, the characteristic X-rays of atoms are emitted or fluoresced upon absorption of primary or incident X-rays of shorter wave-lengths (higher energies). The K spectral lines are used for elements of atomic numbers 13 to about 63, and the L series for those above atomic number 50. Whether the K or L lines are used for elements 50-63 depends upon the type of instrumentation available. The laboratory at the Eastern Experiment Station of the Bureau of Mines, College Park, Md., uses the K lines up to atomic number 57 and the L lines for thong elements of higher atomic number.

Jan 1, 1955

By T. M. Nasiatka

This report sterns from a study undertaken by the Federal Bureau of Mines to determine the possibility of reducing filter-cake moisture by applying radiant heat. Suitable laboratory equipment was set up to study the effect of heat, heating time, proximity of the heater to the filter cake, cake thickness, and other variables related to the final filter-cake moisture. A minus-48-mesh coal slurry and application of heat for 60 seconds resulted in filter-cake moistures 5.6 to 13.2 percentage points lower than could be accomplished by filtration alone at 24 inches of Hg for 1-1/4-and 1 1/2-inch cake thickness, respectively. The moisture reduction can be attributed to the combined effect of lower fluid viscosity and evaporation.

Jan 1, 1959

By G. E. McElroy

"while investigating the presence of heavy strata gases* in certain mines of the East Tintic mining district of Utah, a small, local body of light, very hot gas of high-nitrogen composition was noted in one of the mines. Observations and analyses indicate that this light gas was resulting from very rapid oxidation of finely disseminated pyrite, in lead-silver sulphide ore. The gas was actually mine air which had lost a large proportion of its oxygen content by reaction with the pyrite. This body of gas was hanging in a local high spot about 5 by 5 by 5 feet in size, caused by caving, at the end of a crosscut. Fifty feet from this spot, an air current of 6000 cubic feet per minute was entering the 5 by 7 foot cross-cat from a raise from below.On account of the vapor contained in the gas, the bottom level of the gas could be plainly seen and was practically a horizontal plane, but of slightly wavy appearance, coinciding with the point where an acetylene light was extinguished. This body of gas was visited on three occasions and samples obtained by means of evacaated bulbs and by water displacement. The temperature of the gas was ap¬proximately 175 degrees P. on all three occasions, so that sampling required thick gloves and quick action. Air three feet below the vapor line had a temperature of only 120 degrees F., and a relative humidity of 27 per cent. The stratification of the air and gas mixtures was so sharply defined that the sampler could hold his head a few inches below the vapor level for an appreciable period of time without any noticeable effect other than that due to the high temperature. At one foot below vapor level, it was 135 degrees F., and the relative humidity was 30 per cent. When a candle and an acetylene light were raised into the gas from below, the candle flame was extinguished at a point two inches lower than the acetylene flume, indicating a drop in oxygen content from about 16 per cent to 12 per cent (oxygen content of normal dry air 20.05 per cent) in the distance of two inches."

Sep 1, 1921

By Kenneth J. Miner

Pittsburgh bed and Lower Freeport bed coals were tested in the U.S. Bureau of Mines two-stage froth flotation pilot plant, which utilizes a new flotation process to remove pyritic sulfur. The process consists of a first-stage coal flotation step to remove coarse, free pyrite and other refuse in the tailings. The clean coal froth concentrate is then repulped and treated with a coal depressant, a pyrite collector, and a frother to selectively float the remaining pyrite in a second stage. Results in the pilot plant were excellent, comparing well with those obtained in laboratory batch tests. That is, about 70 percent of the pyrite present in the Pittsburgh bed coal and about 90 percent of the pyrite present in the Lower Freeport bed coal were removed with excellent final clean coal recoveries.

Jan 1, 1973

By J. C. Holtz

Since 1937 the Bureau of Mines has conducted investigations to provide the technical information necessary to guide the safe use of diesel engines underground in the United States. Coincident with the beginning of the technical study, a survey was made of State regulations pertaining to the use of internal-combustion engines underground.3/ At that time it was found that owing to the known hazards of gasoline locomotives, many States had enacted legislation or regulations limiting or prohibiting their use underground. Some of this legislation prohibited, or could be interpreted as prohibiting, the use of any type of internal-combustion engines in underground workings. After World War II diesel-powered equipment was introduced underground in many States, and pertinent questions are received frequently by the Bureau of Mines about the regulations that permit such applications. Because it was known that new and revised regulations had been made effective in some States in the nearly 20 years that have elapsed since the previous survey,3/ the Bureau decided that a review of the latest regulations in the leading mineral-producing States would be a valuable source of information for those engaged in the production of minerals as well as others. Accordingly, where feasible, this report includes abstracts of State laws and regulations as they affect the use of internal-combustion engines underground, particularly diesel engines. The substance of comments from State officials also are included when these appear to be helpful to interpretation of the regulations.

Jan 1, 1957

By James H. Aase

Selected glacial lake clay deposits in Minnesota were sampled, tested, and evaluated to determine their suitability for use as a bonding agent in iron ore pellet manufacturing. Preliminary tests conducted on clay samples obtained from five ancient glacial lake basins identified the clays in the Lake Agassiz glacial lake basin near Cook, Minn., as having the greatest bonding potential. An auger drilling program was conducted to obtain substantial quantities of representative material for detailed testing. The drilling indicated the presence of large clay reserves in excess of 500 million tons within the 12-square-mile area investigated. Bench scale tests indicated that the bonding properties of Cook area clays, when activated with relatively small quantities of sodium carbonate monohydrate (Na2C03?H2O), imparted excellent strength characteristics to iron ore pellets. Larger scale continuous pelletizing tests were made to confirm the bench scale results. These tests indicated that use of 1 percent activated clay alone as binder gave the iron ore pellets an overall strength slightly lower than with 0.75 percent bentonite, considered the industry standard. Use of 0.5 percent activated clay plus 0.5 percent bentonite produced better pellet strength qualities than use of 0.75 percent bentonite alone, without increasing the silica plus alumina content. The data from both bench scale and larger scale continuous tests suggest that the Cook, Minn., clays can be utilized after activation either alone or in combination with bentonite at an economic advantage over present pelletizing practice with bentonite.

Jan 1, 1968

By W. M. Weigel

"The use of sand for the filtration of municipal water supplies is comparatively recent use in this country, although at the present time, most cities of any size that draw their water supply from surface sources use sand filters in their purification system. Not only are sand filters employed to remove sediment and suspended matter, but they also take out most of the bacteria in the water.The first comprehensive research and study of sand for this purpose was probably that of Hazen for the Massachusetts Board of Health in 1891 and 1892, although sand filters had been employed for a considerable time before, specifications for filter sand drawn since then have been largely based on the results of Hazen's work,The general requirements for filter sand are more exacting than for any of the different kinds of sands, except the chemical specifications for glass sand. Filter sand must be uniform in size and within certain limiting sizes. In addition, it must be clean and free from clay and organic matter and of fairly high purity. Early investigations established the fact that an excess of fine materiel increased the friction and decreased the rate of flow through the filter, and that the size of the finer particles rather than the courser, determined the effective size. Also, that large grains tended to cause irregularities in flow in different parts of the bed. There is no requirement as to grain shapes, except that they be not flat or elongated, since, so far as known, either rounded or angular grains are equally efficient.Based on Hazen's investigations, two factors are quite generally used to control the average size and uniformity of size of the sand. These are defined as follows: The ""effective size"" of a sand is such that 10 per cent by weight of the seed is finer than this size, end 90 per cent is coarser. It is expressed in millimeters, The ""uniformity coefficient"" is defined as the ratio of the size of grain which has 60 per cent finer than this size to the size which has 10 per cent finer (the ""effective size""). It is evident that the smaller this coefficient, the more uniform is the seed. If all the grains were exactly the same size, the coefficient would be 1."

Jul 1, 1924

By R. R. Backer

The Bureau of Mines investigated the typical physical and chemical properties of coal waste materials from the western part of the United States. The results are compared, in so far as possible, with the properties of waste materials from eastern coal operations. The authors found a disparity of mines and preparation plants among western U.S. coal operations and dissimilarities with typical operations in the East. The relatively cleaner product from the predominance of surface mining and the occurrence of thicker seams in the West reduces the amount of coal preparation required and the size of the waste piles. Because of the abundance of land available for waste disposal, many of the piles are low and extended over large areas. New concepts relating statistical shear strength data to liquifaction potential are presented. The somewhat limited data indicates that western coal sludge is coarser with higher permeabilities and shear strengths than the eastern deposits.

Jan 1, 1977

By D. R. Dolinar, J. Pablic, D. C. Oyler, T. P. Mucho

At a mine in central PA, high horizontal stresses have caused long running roof falls resulting in hazardous conditions for the miners and the premature abandonment of panels. Because of these conditions, the mine requested assistance of the National Institute for Occupational Safety and Health (NIOSH) in utilizing the 'advance and relieve method to mitigate the affects of horizontal stress on the mine roof. "Advance and relieve" mining involves the removal of a pillar or a portion of a pillar during development, thereby creating a cave along one side of the panel. Following cave development, the horizontal stress is relieved over the workings adjacent to the cave in the active panel. The mine has used this system in three panels with a significant reduction in stress damage and no large roof falls.

By Paul Hopkins

The following methods have been selected from a large number tried while assaying several hundred samples of placer concentrates. It is thought that some of these methods may be useful to those who are required to assay similar products containing large quantities of metallic articles, such as jeweler's sweepings. No great difficulties will be encountered in assaying black sand from beaches or river bars. Such samples require care in grinding and sifting so that no oversize particles of gold or platinum are lost. It is also necessary to have sufficient silica in the flux to form a fluid slag with the excess of iron, magnesium, or chromium which such samples contain. It is much more difficult to assay black sands, or concentrates, produced in large-scale placer-mining operations. These products are usually much harder and more abrasive than the beach black sands. They also contain numerous metallic particles resulting mainly from wear on the mining machinery. These particles consist chiefly of iron or steel but also contain lead, copper, and alloys such as babbitt, solder, brass, ferrosilicon, etc. Fairly large particles of gold are often found. Some samples will contain as much as 10 percent of such metallic particles. It is not feasible to remove the particles of iron with a magnet and discard them, as they invariably contain gold, sometimes a considerable amount. This gold is attached to the iron particles by rust or wedged into cavities. Scraps of sheet iron are often found which have become tightly folded or rolled and contain gold or amalgam within the folds.

Jan 1, 1934

By H. H. Schrenk, L. B. Berger, Robert L. Beatty

"INTRODUCTION Toxic oxides of nitrogen 5/ are formed or liberated in many industrial process and may constitute a definite hazard to the health of persons exposed to the atmospheres thus produced. Oxides of nitrogen occur in the gases involved in the use of explosives, in the gasoline products of welding operations in the exhaust of internal-combustion engines, in the vicinity of electrical discharges, in the combustion of nitrated materials, and in chemical process involving nitration or the use of nitric acid, Itis evident that oxides of nitrogen may constitute an occupational hazard in many industries, and therefore it is important that those concerned with the control of such hazards be equipped with a technique suitable for the determinations of oxides of nitrogen in the concentrations of,hygienic significance."

Feb 1, 1943

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. .It presents analytical data for 4, 457 samples, representing the products of 92 companies. The samples were collected by companies during June, July, and August 1956, As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation. A list of the National Motor Gasoline Survey reports published during the past 10 years is on page 5.

Jan 1, 1957

1. In 2003, a total of 4,357 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA). The major industrial classifications in stone mining are dimension stone (used for construction purposes), crushed and broken stone (aggregates), cement, and lime. • Stone mines comprised 30.3% of all mining operations. • Mines producing crushed and broken stone (n = 3,412) comprised 78.3% of all stone mining operations.

Feb 1, 2005

By Nicholas Kyriazi

A performance comparison of 14 rescue breathing apparatus was undertaken as an assessment of past and present worldwide technology. Rescue breathing apparatus are self-contained, closed-circuit breathing apparatus used for entry into areas having atmospheres that are immediately dangerous to life and health. Apparatus tested were the Biomarine BioPak 45, 60, and 240; the Draeger BG 4 and BG-174A; the Litton LITPAC II; the MSA Custom 4500 II Air Mask, Chemox, and McCaa; the Sabre Selected Elevated Flow Apparatus (SEFA); the Scott Rescue-Pak; the Siebe Gorman Aerorlox and Proto Ten; and the SurvivairLP-120. The apparatus were tested on an automated breathing and metabolic simulator at the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH). Physiological parameters monitored during the testing were average inhaled CO2 and O2, minimum inhaled CO2, inhaled wet-and dry-bulb temperatures, and peak inhalation and exhalation breathing pressures. The metabolic demand on the apparatus was 1.35 L O2/min for most of the test with two 5-min intervals of 2.5 L O2/min, the first beginning 10 min into the test and the second beginning 10 min before the end of the rated duration of the apparatus. Results presented include apparatus service life and test-averages of monitored physiological parameters. Schematic drawings and photographs of the apparatus are also included. The Draeger BG-174A and BG 4 had the highest durations—295 and 291 min, respectively. The BG 4 hadthe lowest minimum inhaled CO2 levels, attesting to the effectiveness of its CO2-absorbent canister. The SabreSEFA had the lowest average inhaled CO2 levels, due mostly to the apparently low-dead-space mask andnose cup. The MSA Air Mask, the only open-circuit device tested, had the lowest wet- and dry-bulb temperatures, with the liquid-O2-source Siebe Gorman Aerorlox having the next lowest temperatures. The only apparatus with a CO2-absorbent not in a packed-bed design, the BG-174A, had the lowest exhalation pressures. The BG 4 had the highest level of positive pressure, with the Biomarine BioPak 60, Survivair LP-120, SEFA, and Litton LITPAC II nearly as high. The BG 4 had the lowest pressure swing, with the SEFA a close second.

Jan 10, 1999

By Michael T. Nigbor

The Bureau of Mines assisted the Rocky Mountain Energy Co. in a pilot-scale in situ leaching experiment at Casper, Wyo., to determine if sulfuric acid can be used as a cost-effective alternative lixiviant (leachant) for uranium in situ leaching. This experiment, which lasted more than 2 years, is the first fully documented pilot-scale operation in which the leaching-restoration cycle was completed using sulfuric acid instead of the more common carbonate-bicarbonate leachant This report describes activities at the experimental site, presents extensive geochemical data from startup to site restoration, compares laboratory and field experiments, and discusses the environmental aspects of acid leaching. The data showed that sulfuric acid is apparently an effective leaching solution. Three to five grams of acid per liter of ground water resulted in a production solution grade of 80 to 100 ppm uranium. Restoration was successful, but required extended flushing. The pH was the last chemical parameterto return to baseline, requiring about 350 days. This was longer than was predicted in laboratory simulations. The data also showed that mobilization of toxic elements such as selenium, arsenic, radium, thorium, and molybdenum stayed within reasonable limits and quickly fell back to preleach concentrations during restoration.

Jan 1, 1982

By Byron E. Blair

This report describes procedures for using a high-speed camera to study blasting phenomena. Both quantitative and qualitative information can be obtained, provided that proper interpretations of the projected two-dimensional images are made. Geometrical relationships between object and image displacements are given in terms of horizontal and vertical angles of the camera optic axis with respect to the quarry face. Correction factors are given for obtaining true object displacements from image displacements in the camera film plane. The time of initial rock movement also is considered, and the control-ling factors of camera speed, scale factor, minimum increment of projection measurement, etc., are evaluated in terms of minimum time intervals. The high-speed camera and associated equipment are described, and field measurements and laboratory data analysis techniques are outlined. An analysis of a typical high-speed motion picture is made, and the application of the necessary correction factors is illustrated.

Jan 1, 1960

By Neal M. Muir

The increasing demand for iron ores prompted the Bureau of Mines to investigate the sources of past production in Kentucky to determine whether reserves of usable ore still exist. Preliminary investigation showed that the holdings of the Rose Run Co. were the most promising, inasmuch as the deposit had not been exhausted by past mining and the property was near railroad facilities and but 80 miles from the blast furnaces at Ashland, Ky. The Bureau conducted a churn-drilling and sampling program to investigate the depth, thickness, and iron content of the ore beds so that they might be evaluated as a possible reserve of low-grade iron ores. The Rose Run area in Bath County, Ky., was explored by 74 churn-drill holes totaling 2,059.4 feet of drilling and 4 cuts and test pits. Fifty-seven drill holes and the four test pits penetrated the ore bed at an average depth of 22 feet. The bed had an average thickness of 2.54 feet. Analyses show that the calcium and magnesium carbonate content is more than sufficient to flux the silica and provides an excess that needs an admixture with other siliceous iron ores.

Jan 1, 1950

By Manuel Gomez

Dehydrogenation factors, proximate analysis, and ultimate analysis were examined as predictors of the low-temperature -carbonization properties of coals varying in rank from lignite through anthracite. All factors studied contributed to reduction in variance of the sample populations investigated. Response surface regression models based on variables from proximate and ultimate analyses of coal were constructed for eight low-temperature carbonization assay product and gas component Fields. These models were tested with independent samples that included drill cores, sized fractions, petrographic fractions, and run-of-mine coal. The models developed were used to predict low-temperature carbonization yields or coals from major fields of Wyoming. This information was cast in the form of contour plots describing the potential low-temperature carbonization product yields of Wyoming coals and the properties of the resultant char or coke. The variables used as input v the models may be measured and collected during exploration; thus, the carbonization properties of a seam can be determined in advance of mining. The information presented in this report is useful in that it broadens the deciionmaking base for management when either mine locations or coal conversicl plant sites, or both, are being considered.

Jan 1, 1971