Search Documents

By Frank J. Wiebelt

Work on the Abbott-quicksilver property was part of the general program of th~ Bureau of Mines in its investigation of domestic mineral resources, which are essential to national defense or industry and of which our present or probable future supplies are inadequate. The mine was discovered in 1862, and the intermittent production up to 1947 has totaled around 37,500 flasks of quicksilver. Output has come from ore shoots formed in the vicinity of fault intersections in a narrow zone composed of lenses of silicified serpentine breccia interbedded with shale. Work by the Bureau included the drilling of six diamond-drill holes aggregating 2,845 feet. Several possible ore zones were intersected by the drill holes. Field work was begun in April 1948 and concluded in October of the same year. This report gives detailed results of the diamond drilling and a brief account of the history and description of the ore deposits.

Jan 1, 1949

By S. J. Page, W. R. Reed, J. A. Organiscak

NIOSH continues to conduct respirable dust control research for surface mine blasthole drilling operations. Research areas have included testing variables (shroud leakage area, drill deck cross-sectional area, shroud height, collector-to-bailing airflow ratio, etc.) that have the most impact on respirable dust control, development of a dust collector inlet hood, development of a dust collector dump point shroud, and testing of a small diameter water separating sub. This paper summarizes the results of the aforementioned research that has been completed. Additionally, past dust control research for drilling operations of both underground and surface mines completed by the U.S. Bureau of Mines, created in 1910 and incorporated into NIOSH in 1997, is reviewed.

The method of using large-diameter augers to recover coal was introduced to the mining industry about the end of World War II, and production of bituminous coal with augers has increased steadily to an estimated 7 million tons, or approximately 1.4 percent of the total mined in 1956. Although auger mining has proved to be a reliable and economical method of mining coal, a number of unfortunate fatal accidents have been experienced; consequently the need for these recommended safety standards is indicated for this comparatively new method of coal mining. As mining methods and equipment change from time to time and new hazards are introduced, these standards will be revised; therefore, questions or suggestions from the coal-mining industry will be welcomed and carefully considered.

Jan 1, 1958

By D. A. Doughty

The Bureau of Mines developed two methods for determining iron II and iron III in 2- to 5-mg samples of coal using electron paramagnetic resonance (EPR) spectrometry. One method used solid coal samples; the other method used aqueous solutions. The method using solid samples was more simple, technically, but required the use of X-ray fluorescent analysis, or another independent method, for determining total iron in the samples, and the results were subject to some uncertainty. The method using aqueous solutions appeared capable of greater certainty and did not require additional methods of total iron analysis but was more involved procedurally. The coals analyzed were found to contain much more iron II than iron III.

Jan 1, 1973

Develop a means for estimating vertical stress conditions in or around an underground mine so that appropriate measures for ground control can be taken before hazardous conditions arise. Background High vertical stress in an underground mine could cause or enhance hazardous ground control conditions which might lead to accidents, fatalities, and loss of reserves. An understanding of the vertical stress conditions at the mining level would allow a mine operator to take precautions that will minimize the occurrence of ground control problems. A knowledge of the underground stress conditions prior to mining could be used as an aid in future mine plan development to avoid or minimize ground control problems. Approach The Bureau of Mines developed a computer program for calculating the vertical stress resulting from the pressure of overlying rock masses on a mine or geologic surface at various depths.

Jan 1, 1990

By Gerald L. Finfinger

The Bureau of Mines conducted an experimental degasification project in Island Creek Coal Co.'s Virginia Pocahontas No. S mine. Methane from the overlying Pocahontas No. 4 coalbed was entering mine workings in the Pocahontas No. 3 coalbed through fractures in the roof rock. Small-diameter (l-S/B-inch) holes were drilled into the overlying coalbed to reduce the gas pressure and intercept methane flows, which were piped to the surface through an underground 6-inch-diam steel pipeline. The total methane flow rate from the vertical holes averaged 150,000 ft3/day for the first month. Methane flows into the mine were reduced by 47 pet, thereby demonstrating the effectiveness of this form of degasification in reducing ventilation requirements and providing a safer working environment.

Jan 1, 1979

1. In 2003, a total of 1,972 coal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Coal mines comprised 13.7% of all mining operations. • Bituminous mines comprised 92.5% (n = 1,825) and anthracite mines 7.5% (n = 147) of coal mining operations. • More than 70% of all coal mines were located in three states: Kentucky (29.0%), West Virginia (20.9%), and Pennsylvania (20.2%). • Bituminous coal mines reported the production of over 1 billion coal tons.

Feb 1, 2005

By R. V. Ramani, V. T. Burgos, J. A. McClay

General The underground mining environment has traditionally been hostile and as early mines were developed, coal seams with particularly difficult natural conditions were bypassed in favor of those more easily exploited. Barring the discovery of new and novel sources of energy, the depletion of petroleum and natural gas reserves will eventually force the United States back to the use of coal as its primary energy source. Figure 1 illustrates the trend away from coal which has taken place over the past half century. Today, the demand for coal requires a re-evaluation of all coal seams to meet the needs of the energy market. Difficult mining conditions may result in an increase in the consumption of roof control materials, require greater investment in pumping and ventilation systems, and increase the need for in-depth engineering of far greater safety in production plans. They may also cause delays in mine development and curtail production, all of which combine to drive up the unit production cost. It is reasonable to expect that conditions will continue to deteriorate as current reserves are depleted, thus bringing this factor into greater prominence in the future. For several years now, it has become apparent that in addition to economic objectives, coal companies must set and achieve several concomitant objectives to accomodate society's interest in the conservation of natural resources. Government action to meet this interest has taken the form of two categories of Federal legislation, environmental protection and employee health and safety. The effects of both of these have not been fully evaluated with respect to the total economic picture, although preliminary evidence indicates that an immediate increase in

Jan 1, 1975

By H. R. Grau

NIOSH’s Pittsburgh Research Laboratory is currently involved in research to identify silica dust generation in underground metal/nonmetal mines. The ultimate goal of this research is to develop control technologies to reduce worker exposure to respirable silica dust. Commodities and job classifications with the highest silica dust exposure have been identified through analysis of the Mine Safety and Health Administration (MSHA) compliance dust sampling database. Dust surveys were conducted in an underground limestone and gold mine to investigate silica dust sources, generation levels, and controls being used. A summary of the mining operations, sampling procedures, resulting data, and suggested methods to improve the dust control will be provided.

By Manuel Gomez

A general prediction model for the Hardgrove grindability index was constructed from 735 coal samples using the proximate analysis, heating value, and sulfur content. The coals used to develop the general model ranged in volatile matter from 12.8 to 49.2 percent, dry basis, and had grindability indexes ranging from 35 to 121. A restricted model applicable to bituminous coals having grindabilities in the 40 to 110 range was developed from the proximate analysis and the petrographic composition of the coal. The prediction of coal grindability within a single seam was also investigated. The results reported support the belief that mechanical properties of the coal are related to both chemical and petrographic factors of the coal. The mechanical properties of coal may be forecast in advance of mining because the variables used as input to the prediction models can be measured from drill core samples collected during exploration.

Jan 1, 1970

By G. P. Sturm

This work was undertaken by the Bureau of Mines in cooperation with the Environmental Protection Agency to determine photochemical specific reactivities of emissions from automobiles using leaded-premium-and regular-grade fuels and prototype lead-free fuels of comparable octane quality. Emissions were photoirradiated in a 100-ft3 environmental (smog) chamber constructed of aluminum and Pyrex glass at three sets of initial hydrocarbon (HC) and oxides of nitrogen (NOx) concentrations. Reactivity was measured and expressed in terms of rate-of-NO formation (RNo2) and dosages of oxidant, peroxyacetyl nitrate (PAN), peroiypropionyl nitrate (PPN), and formaldehyde (HCHO). The results indicate that the evaporative emission samples and the evaporative plus exhaust emissions samples from the lead-free fuels have, in general, higher reactivities per gram than those from the leaded fuels. For the samples containing only exhaust emissions, the only trend observed was the lower specific reactivity exhibited by the leaded premium fuel exhaust. These differences in specific reactivity are taken to reflect the differences in hydro-carbon composition of the fuels and their evaporative and exhaust emissions rather than any difference in lead content per se.

Jan 1, 1973

By L. C. IlsLey

The work of the electrical section of the Bureau of Mines may be considered to have had its beginning in April , 1909 , when H. H. Clark was , appointed electrical engineer in the U. S. Geological Survey. The first manuscript prepared by members of this section was Miners Circular 5, which was issued in October , 1911. During each succeeding year additional papers have been published dealing with questions relating to electrical safety. Since 1916 the electrical section has also conducted laboratory investigations on flame safety lamps and gas- detecting devices and has published reports relating thereto . The following selected list of publications covering safety studies and activities of the electrical section has been prepared for the convenience of those who wish to keep themselves advised concerning electrical safety matters . The list includes only such publications as are applicable to present-day prac tices .

Jul 1, 1930

By Jeffrey Shawn Peterson

The testing procedures of the U.S. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break- flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 1992

By Robert K. Koch

Laboratory-scale studies on defluorination of natural and synthetic fluorspars by pyrohydrolysis at 1,500° C. were made to determine the feasibility of developing a process for producing hydrogen fluoride from siliceous fluorspars. It was found that the reaction (at 1,500° C.) is not promising for process development, even though a silica-free offgas can be generated. The primary difficulty is the low hydrogen fluoride content of the offgases; an HF content of 6 percent was the best achieved. Previous research by the Bureau of Mines has demonstrated that offgases averaging 27 percent hydrogen fluoride can be produced under carefully controlled conditions at 1,280° C. The lower temperature process is a better method for production of HF. However, charges in which the CaF to Si02 mole ratio varied from 0.4 to 2 could be processed with similar results. Also, combined alumina and ferric oxide contents up to 25 mole-percent did not noticeably alter the rate of defluorination. Therefore, virtually any natural siliceous fluorspar would respond in essentially the same manner when exposed to water vapor at 1,500° C.

Jan 1, 1962

In this Part, we have included copies of the flip charts and overhead projector viewgraphs used in the two briefings we conducted as part of this seismic detection and location task. The first one was an overview and problem definition briefing given to the seismic consultants on September 7, 1972. The second was a formal oral presentation of study results to technical staff members of the Pittsburgh Mining and Safety Research Center on November 21, 1972.

Jan 1, 1974

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

5. Development of Initial Probing System 5. 1 Introduction The preliminary evaluation of a variety of potential methods for initial probing showed that the optical system using closed circuit television (CCTV) and the sonar, or acoustic ranging, system were the most promising. The former is capable of pro¬viding a visual display of the mine passages in a clear, non-smoky environment, and the latter is capable of providing a map of the spatial location of the coal surfaces making up the entries, as well as objects, such as cribs, mining machines, etc., in the passages in both smoky and non-smoky environments. The sonar system used in conjunction with the CCTV in a clear environment can greatly assist in resolving the spatial distribution of objects seen on the TV screen. Further, in a smoky environment the interpretation of the sonar information could be facilitated if some visual information were also available. CCTV systems exist but require some modifications to suit this particular application. The Industrial Hazards and Communications Division of the Bureau has an ongoing program for the development of such a CCTV system. Rather than duplicate this effort in developing a CCTV system, it was decided to evaluate the possibility of utilizing their system for initial probing, while continuing with the develop¬ment of a system which would work in any environment, including the presence of dense smoke. The concept of using sonar for the initial probing of mine passages represents the application of new technology requiring development. The results of such a development effort undertaken during the course of this program are described in the following sections.

Jan 1, 1973

By D. N. Nilsen

The Bureau of Mines is investigating a method to recover Ni, Cu, and Co from low-grade domestic laterites through reduction roasting, leaching, sol-vent extraction, and electrowinning unit operations. The objective of this research is to develop processing technology that can convert low-grade domestic deposits containing critical metals into national reserves. As a part of this research, a solvent extraction system was investigated for the extraction of nickel and copper, followed by the separation and production of suitable electrolytes. Nickel and copper were coextracted from ammoniacal ammonium sulfate leach liquors (pH~9.5) with LIX 64N extractant in a laboratory-size mixer-settler continuous circuit. Three extraction stages resulted in >99-pct extraction of nickel, substantial copper extraction, and essentially no cobalt extraction from leach liquors. A crowd stage reduced the ammonia loading on the solvent by maximizing nickel loading. Residual ammonia was removed from the loaded solvent with a pH-controlled scrub. Nickel and copper loaded on the solvent were separated by selective stripping. Typical nickel strip circuit operation using electrolyte containing 90 grams per liter (g/l) Ni and 11.9 g/l H2S04 yielded >99.9 pct Ni stripped from the solvent in five stages. The copper loading on the recycled solvent was controlled in a copper strip stage using electrolyte containing 25 g/l Cu and 160 g/l H2S04,

Jan 1, 1981

By Richard E. Ray, George N. Aul, Fred Garcia, William P. Diamond

Increasing longwall panel dimensions, particularly face width in gassy coalbeds, may result in unexpected increases in methane emissions. To investigate this problem, continuous longwall face emission monitoring studies were conducted at two adjacent mines operating in the Pocahontas No. 3 Coalbed, where longwall faces were to be extended from 229 to 305 m (750 to 1,000 ft). It was predicted by regression analysis of methane emissions data from 229 m (750 ft) wide longwall faces that extending faces to 305 m (1,000 ft) would increase methane emission rates by only 7 percent (0.6 m3/min (20 cfm)), to 8.6 m3/min (304 cfm) at the VP-1 Mine. In contrast, it was predicted that extending faces at the VP-3 Mine could increase methane emissions by as much as 13 percent (1.8 m3/min (65 cfm)) to 16.1 m3/min (567 cfm). The geologic and mine design factors influencing the variation in face emissions between the two mines will be discussed.

By Benton L. Tibbetts

Comprehensive geophysical measurements were made in the Tertiary Channel gravel deposits of Badger Hill, Calif., with the refraction seismograph, gravimeter, and well logging equipment, to develop a three-dimensional physical model of the gold-bearing gravels. Tests were also made of the applicability of magnetometer and electrical resistivity techniques. Results of 14 seismic profiles revealed four distinct layers with velocities of 1,600 ft/sec for loose gravel, 5,900 ft/sec for compact gravel, 8,600 ft/sec for cemented, blue gravel, and 15,500 ft/sec for bedrock. The depth to bedrock along the middle of the channel varied from a minimum of 100 feet in the hydraulically mined pit area to a maximum of about 300 feet in the upper bench area immediately south of the pit. These geophysical methods revealed that 40 percent of the drill holes necessary to delineate the deposit could be eliminated, at a cost saving of at least 30 percent.

Jan 1, 1971

By J. D. Marchant

Solid-state electrotransport of impurities in cerium, lanthanum, and praseodymium, using a pulsed current, was investigated. The results were compared with those of using a steady current. Impurities that showed appreciable movement with the pulsed current, but not with the steady current, were as follows: Molybdenum and oxygen in cerium, aluminum, iron, and molybdenum in lanthanum. The use of a pulsed current enhances the practical application of solid-state electrotransport to remove a wider variety of impurities from the host metals.

Jan 1, 1971