Search Documents

By Nicholas Kyriazi, John P. Shubilla

A joint effort by the U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CFR 75.1714), survived the underground environment with regard to both impact damage and aging. This report presents findings regarding laboratory-tested SCSR's from 1982 through 1990. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except for units with manufacturing defects or design deficiencies. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. This poses a potential danger to a user in an emergency. Recommendations include improved training in inspection procedures.

Jan 1, 1992

By Bruce McDonald

This report contains the Phase I findings of a study to select and test devices for preventing lack of alertness in haulage truck drivers. The extent of the problem was determined by visiting surface metal and nonmetal mines, interviewing drivers and safety personnel and reviewing accident reports. A number of devices for detecting a lack of alertness were considered and three were recommended for testing in actual operation.

Jan 1, 1977

By L. B. Pankratz

Heat content measurements were conducted for GaPo.996 and InPo.986 over the temperature range from 298° to 1,100° K, and for In2S2.897 over the range from 298° to 1,200° K. Both the actual experimental data and values adjusted to conform with the stoichiometric compositions (GaP, InP, and In2S3) were reported. Entropy increments above 298.15° K were calculated for the stoichiometric compounds, and heat content and heat capacity equations were derived.

Jan 1, 1965

By O. C. Blade

This report is one of a series made by the Bureau of Mines under a cooperative agreement with the American Petroleum Institute on the characteristics of commercial aviation gasolines. The series of Surveys is a continuation of like work conducted under aimil.ar cooperative agreements with the Coordinating Research Council, Inc. by the National. Bureau of Standards from 1940 through 1946 and by the Bureau of Mines from 1947 through 1949. A completed list of the series of surveys is given at the end of this paper.

Jan 1, 1951

By L. C. IlsLey

[In 1922 a conference of representative coal-mine operators, cable manufacturers, mining-machine manufacturers, and representatives of the United States Bur eau of Mines vas held at the Pittsburgh Experiment Station, regarding suitable cables for use with permissible raining machines. This conference recommended that the Bureau investigate rubber-sheathed trailing cables in order to obtain specifications for tests leading to approval for rise with mining machines. Effective until such time as an investigation could be made, the bureau asked the several manufacturers of approved mining machines to recommend cables for wise with their machines. In general the Cables recommended tentatively approved. Arrangements for the tests were completed in 1927. Concentric-type cables were investigated first, and Reports of Investigations, Serial No. 2909, covering the tests, was issued in January, 1929.]

Jan 1, 1929

By Vibration Research Group, Natasha K. Lee Shee, Tammy R. Eger, James P. Dickey, Paul-Émile Boileau, Lana M. Trick, Michele L. Oliver

Introduction Industrial exposure to whole-body vibration is associated with injury and discomfort. Certain industries, notably mining, construction, and forestry, involve complex 6 degrees of freedom vibration. Laboratory-based studies of vibration are essential for controlled and systematic evaluation of the human responses to vibration2. The purpose of this pilot study was to evaluate whether the duration of the vibration exposure, and rest between vibrations, significantly influence the subjective ratings of comfort during laboratory-based studies of vibration. Methods Subjects: The cumulative vibration dose was calculated, and was below the health guidance caution zone recommended by International standards3. The experimental procedures were approved by the University of Guelph Research Ethics Board. Ten adult subjects participated in this pilot experiment. All subjects completed the entire experimental paradigm; no subjects complained of pain during or after the experiment. Experimental Design: The experiment consisted of four blocks of vibration exposures; either 15 or 20 seconds of vibration (1 df:Z axis, 3 df:XY plane, 3df:YZ plane, or 6 df) alternating with either 5 or 10 seconds rest. The order of presentation of the four blocks was randomized. Each of the blocks was composed of 37 individual sinusoidal vibration exposures in randomized sequence. This abstract focused on ten identical trials, (6.3 Hz vertical vibration, 0.55 m/s2 RMS) interspersed within each block, in order to assess whether the subjects’ comfort ratings systematically varied between the 15 or 20 vibration exposures, the 5 or 10 second rest between vibrations, or within each block. The experiment involved 43 minutes of vibration within the 62 minute experiment. Vibration Apparatus: A commercial parallel robotic platform was used to apply the specific vibration exposures (R2000, Parallel Robotics Systems Corporation, Hampton, New Hampshire). The subjects sat on a passenger seat from a 1992 Honda Accord that was rigidly mounted to the robotic platform (Figure 1). This robotic system performed the specific vibration exposures operating under closed-loop displacement control. A custom-written Matlab program automated the testing sequence.

Jan 6, 2006

By R. Demont, A. Pranesh, S. Rakheja

Ethical concerns of in-vivo procedures and poor repeatability of non-invasive techniques have been major limitations in estimating vibration-induced spine loads through experiments. The biodynamic models of seated human body exposed to whole-body vibration (WBV) have evolved for defining the frequency-weightings, enhancement of human responses to WBV, and developing anthropodynamic manikins for seating assessment activities. The widely reported mechanical-equivalent models, solely based on through- or to-the-body biodynamic response functions, do not seem to resemble the biomechanical structure and do not yield information on the dynamic loading and deflections of segments of concern, namely the spine. On the other hand, biomechanical models with representative anatomical structure and anthropometry are being attempted to simulate segmental movements and the coupling effects, using Finite elements (FE) or multi-body dynamics (MBD) formalisms, which could provide important insights into the inter-vertebral forces [1]. While the FE models pose considerable complexities primarily related to characteristics of the bio-material properties, the MBD technique with discrete rigid bodies offers the flexibility to create multi-segment models with relative ease and lower computational cost. In this study, a preliminary multibody dynamic model of a seated human body exposed to WBV along the vertical direction is formulated using MSC/ADAMS software. The model validity is demonstrated by comparing selected responses with the available measured data. Methods The seated human is represented by nine rigid body segments, including: head, neck, thoracic and lumbar torso, pelvis, hands and thighs, as shown in Fig. 1. The rigid bodies are coupled through different rotational and translational joints, some of which are force elements to allow vertical translations and sagittal–plane rotations of the segments. The measurements of transmission of vertical vibration through-the-body generally require subjects to voluntarily maintain a vertical head position to reduce head-accelerometer orientation errors. The head–neck–shoulder joint is thus considered to be rigid. The shoulders are assumed to be rigidly attached to the thoracic segment. The torso is made up of three (upper, middle and lower) segments connected by visco-elastic revolute and translational joints to permit relative pitch and vertical motions. The forces and torques generated by the joints are derived assuming linear stiffness and damping properties, which were identified from published studies. The pelvis is connected to the rigid seat by similar elements representing the visco-elastic properties of the buttock tissues. The two thighs are rigidly connected to the pelvis, while the segment masses are chosen from the anthropometric data for the 50th percentile male subject. The initial model parameters for the joints were obtained from [2]. The model was analyzed to determine the force-motion relationship at the buttock-seat interface expressed in terms of

Jan 6, 2006

By Claude A. Tongish

This Federal Bureau of Mines report presents information on the accumulation and distribution of helium in U.S. natural gas reservoirs. The investigation concerns the relationship or association of helium with geographic location, geologic age, reservoir depth, nitrogen, carbon dioxide, and argon. Although helium is a minor constituent in natural gas, these data show that certain conditions make some reservoirs statistically more favorable than others for the accumulation of helium. The report is based on gas analysis information collected-by the Bureau from 1917 to 1974 from 10,086 gas samples, representing 6,455 reservoirs in 35 States. The occurrence of helium in the reservoirs was 11.5 percent with less than 0.005 percent of helium, 70.9 percent with 0.005 through 0.29 per-cent of helium, and 17.6 percent with 0.30 percent or more of helium in the gas. Results of the various correlations are presented in tables and charts. Relationships have also been determined quantitatively by measures of correlation. The statistical data can be used to determine the environment under which reservoirs with high-helium contents are most likely to occur. These data can be used with other information for predicting the future helium resources of the United States.

Jan 1, 1980

By C. W. Schultz

The vapor pressure of manganese in equilibrium with a series of liquid iron-manganese alloys was determined by the carrier gas method over a broad range of alloy composition. From these data the activities of manganese in the iron-manganese system were calculated. The system appears to be ideal.

Jan 1, 1966

Objective: Improve the dust control effectiveness of enclosed operator cabs on surface mining equipment.

Oct 1, 2007

By Jay F. Colinet

Respirable dust exposure has long been known to be a serious health threat to workers in many industries. In coal mining, overexposure to respirable coal mine dust can lead to coal workers? pneumoconiosis (CWP). CWP is a lung disease that can be disabling and fatal in its most severe form. In addition, miners can be exposed to high levels of respirable silica dust, which can cause silicosis, another disabling and/or fatal lung disease. Once contracted, there is no cure for CWP or silicosis. The goal, therefore, is to limit worker exposure to respirable dust to prevent development of these diseases. The passage of the Federal Coal Mine Health and Safety Act of 1969 established respirable dust exposure limits, dust sampling requirements for inspectors and mine operators, a voluntary x-ray surveillance program to identify CWP in underground coal miners, and a benefits program to provide compensation to affected workers and their families. The tremen­dous human and financial costs resulting from CWP and silicosis in the U.S. underground coal mine workforce are shown by the following statistics: ? During 1970?2004, CWP was a direct or contributing cause of 69,377 deaths of U.S. underground coal mine workers. ? During 1980?2005, over $39 billion in CWP benefits were paid to underground coal miners and their families. ? Recent x-ray surveillance data for 2000?2006 show an increase in CWP cases. Nearly 8% of examined underground coal miners with 25 or more years of experience were diagnosed with CWP. ? ?Continuous miner operator? is the most frequently listed occupation on death certificates that record silicosis as the cause of death.

Jan 1, 2010

By F. E. Brantley

Blister copper was successfully deoxidized with any of a variety of reducing gases; lancing techniques or a vertical-column furnace were used to contact the copper and gases. Of the gases tested, butane, when used to lance molten copper at about 1,200° C, reaction temperature, was slightly more effective than propane, natural gas, carbon monoxide, or reformed gas for deoxidizing copper from about 1.0 to less than 0.1 percent oxygen content, Laboratory-scale tests revealed that the vertical furnace, composed of a heated column packed with silicon carbide chips or hollow carbon cylinders, was significantly faster and more efficient than the lancing technique for deoxidizing molten copper with any of the gases tested. Comparison of the gaseous-reduction method with the conventional poling method suggests that the gaseous method has important technical and economic advantages for deoxidizing blister copper to any readily controlled amount of residual oxygen content.

Jan 1, 1962

By Emery Chilton, Charles Taylor, Mark Senk, Linda McWilliams

Three-axis ultrasonic anemometers are used to study airflow in the NIOSH ventilation gallery where ventilation in an underground mine is simulated. In this study, performance characteristics of this anemometer are evaluated and the effects of sensor orientation and sampler location on flow readings are examined. The study results provide guidelines for more effective use of the ultrasonic anemometers in the ventilation gallery.

The Mine Safety and Health Administration (MSHA) defines an independent contractor as “any person, partnership, corporation, subsidiary of a cor-poration, firm, association or other organization that contracts to perform services or construction at a mine.” Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines.

Sep 1, 2007

By George A. Morgan

The 53 countries that constituted Africa in 1989 accounted for a significant portion of total world output of a number of mineral commodities. Among the most significant minerals to be produced in Africa were andalusite, antimony, asbestos, bauxite, chromite, coal, cobalt, copper, diamond, fluorspar, gold, lithium minerals, manganese, phosphate, platinum-group metals, and the titanium minerals-ilmenite and rutile, vanadium, vermiculite, and zircon. Despite the underdevelopment of much of Africa, mineral raw materials played a very important part of the national economies of many of its countries. In terms of percent-age of export earnings, minerals accounted for more than 90% in some cases. In several countries with agrarian economies and little economic diversification such as Angola and Guinea, a single mining operation could represent an important source of foreign exchange. These latter operations tended to be the more easily mined surface deposits of diamond, gem stones, and precious metals. Mineral commodities for which Africa had a high percentage of world output were bauxite, 16%; chromite, 44.5%; cobalt, 76.5%; copper, 13.9%; diamond, 50.7%; gold, 32.9%; manganese, 27.1 %; phosphate, 22.1 %; platinum-group metals, 48%; uranium, 29.2%; vanadium, 54%; and vermiculite, 41 %. Several of these, chromite, cobalt, diamond, and manganese, were not produced in the United States.

Jan 1, 1992

By W. S. Landers

This report presents a study by the Federal Bureau of Mines of technical factors related to the production of special carbon and tar from selected Wyoming coals. Certain Wyoming high-volatile bituminous and subbituminous coals were processed in bench-scale apparatus to determine potential carbonization yields and in pilot plant retorts to produce sufficient char and tar for testing. These tests have shown that a critical selection of coal is necessary when the coal is processed for a specialized carbon. Generally high yields of tar are obtained from low-temperature carbonization of Wyoming high-volatile bituminous and subbituminous coals, and the yield of tar usually increases with increase in rank within this range of coals. The production and evaluation of industrial carbons from Wyoming coals by using pilot plant and bench-scale techniques is part of the continuous program of upgrading western coals. It has been found that: 1. Most Wyoming coals are nonagglomerating and may be carbonized in fluidized systems. Chars produced in pilot plant retorts at low temperatures contain about 17 to 23 pct, residual volatile matter and are easily ignited. These chars appear suitable as power plant fuel. The tar-plus-light-oil yields range from 14 to 40 gal./ton of raw coal processed. 2. Wyoming high-volatile coals produce a slightly smaller and somewhat weaker coke than currently mined Western United States high-volatile coals used commercially as blending stock in metallurgical coke production.

Jan 1, 1961

By M. Kanda, W. D. Bensema, J. W. Adams

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in and above an operating coal mine, McElroy Mine, located near Moundsville, Nest Virginia. The electromagnetic environment created by 300 volt dc and 480 volt ac machinery was measured. In one technique noise was measured over the entire electromagnetic spectrum of interest for brief time periods. The noise was recorded using broadband analog magnetic tape. The noise data was later transformed to give spectral plots. In the other technique, noise amplitudes were recorded at several discrete frequencies for a sufficient length of time to provide amplitude probability distributions. The specific, measured results are given in a number of spectral plots and amplitude probability distribution plots.

Jan 6, 1974

By Jack E. Fraley

In this Bureau of Mines study, sealants containing mineral wool, cement, etc, were sprayed through dry-process equipment that propels dry material pneumatically to the water-adding nozzle. Advantages over slurry applications include no mixing, no extensive cleanup, and freedom from hardened cement in equipment should power be lost. Sealants with large mineral wool nodules (>l-inch) were sprayable at rates to 900 square feet per hour for 1/2-inch thickness with little dust and smooth material flow through equipment, but they were weak for mine use, Materials containing small wool nodules (1/4-inch) were stronger but tended to plug lines because the nodules were inadequately separated in the shredder. Increasing the dedusting oil also increased line plugging by holding the nodules together in larger lumps. Best results were obtained using a 3/4-inch-nodule wool with cement binder, which provided both smooth flow through the machine and adequate strength.

Jan 1, 1977

By C. E. Reistle

The generation of steam for drilling operations has visually been accomplished in the past by the use of portable locomotive-type boilers without the aid of auxiliary equipment or advanced for economizing fuel or water consumption. This has been due primarily to the fact that the steam-generating plant of a drilling well must necessarily be of temporary and portable design, and the amount of steam generated has not been considered sufficient to justify the additional expense necessary to obtain more economical operation. However, with the constantly increasing depth to which oil wells are being drilled and the use of larger and heavier equipment, the steam requirements have reached a point where equipment and methods that were previously considered as applicable only to permanent plant installation can be and are being used to a decided advantage by the more progressive operators. As an example of the present-day requirements and the rapidly increasing steam consumption in rotary drilling, a comparison between the requirements during the intensive drilling period in the Seminole end Oklahoma City fields of Oklahoma is of interest. In the Seminole field. There the approximate depth of rotary drilling was 3,500 feet, the general practice was to use three 85 to 90 or 100 horsepower A. P. I. code boilers operating at a working pressure of 175 to 200 pounds per square inch. The fuel end water consumption was approximately 450 to 500 thousand cubic feet of gas and 700 to 750 barrels of water per day. In the Oklahoma City field, where the average drilling depth is approximately 6,500 feet, the general practice is to use either four 100 or 116 horsepower or three 123 horsepower A.P.I. code boilers, operating at a pressure of 250 pounds per square inch. The fuel and water consumption varies from 550 to 750 thousand cubic feet of gas and from 1,000 to 1,500 barrels of water per day.

Jan 1, 1930

By Federick W. Miller

The Bureau of Mines has investigated the availability of columbium from 19 deposits (3 producers and 16 nonproducers) in 7 market economy countries (MEC?s). Brazil has the largest recoverable columbium resource, posessing approximately 2.39 million metric tons Wmt), or 69 pet of the MEC total (3.47 Mmt). The Western Hemisphere countries of Brazil, Canada and the United States contain 3.14 Mrnt of recoverable columbium or 90 pnt of the MEC total. Columbium recovered as a byproduct of tin mining is not included as part of MEC resources in this study. Currently producing mines are Araxa and Catalao in Brazil, and Niobec in Canada, These three mines have 2.42 Mmt of recoverable resources or approximately 69 pct of the MEC total. It is estimated that these mines, operating at full capacity, could satisfy cumulative MEC demand (based on an annual growth rate of 5.1 pct) for the next 20 yr. The United States is totally dependent upon foreign sources for its columbium supply. The majority of U.S. columbium is imported from Brazil in the form of steelmaking- grade ferrocolumbium. Canada has been the sole source of pyrochlore concentrates since Brazil discontinued exports in 1981. The United States also imports small (but important) quantities of columbium as columbite concentrates from Nigeria and Brazil, as columbite contained in tin slags from Thailand and Malaysia, and as synthetic concentrates from the Federal Republic of Germany.

Jan 1, 1986