Search Documents

By H. Kenworthy

Small batches of fluorspar flotation concentrates were made into nodules and pellets on a laboratory scale. Several of these were rated acceptable by laboratory evaluation methods. The most satisfactory pellets were produced by mixing fluorspar with about 12.5 percent of water, by weight, and 4 percent of organic binders. These binders) for the most part) originated from petroleum and wood-pulp industries. They were generally difficult to handle and were not easily incorporated with the fluorspars tested. Most of them seemed to have an aversion for damp fluorspar and had to be forcibly mixed with the fluorspar; which was then formed into pellets by pressure. Substitution of fuel oil in varying amounts in the binders enhanced the mixing and penetrating qualities of these binders but at the same tire tended to make the pellets more porous. Tall oils performed the same function to a lesser degree and usually decreased the water absorbency of the finished pellets. Heat-treating temperatures to set up these binders were moderate -about 5000 F. for 30 to 50 minutes was usually enough for both drying and heat treating. Nodules made with 1-1/2 to 2 percent of bentonite as a binder were easily mixed and formed. They required a high degree of heat (about 1,500° F.) to develop their strength and were quite water-absorbent when finished. Two fluorspars were examined for weight and fluorite loss after heat treatment at similar temperatures. Both showed a definite wej.ght and analytical loss of fluorite. Bentonite was used also as a binder to successfully nodulize finely ground oxides of iron, manganese, and nickel.

Jan 1, 1951

By G. S. Scott

[In the course of the investigation the Bureau of Mines is carrying on to determine the causes, behavior, and control of mine fires, the detection of incipient heating underground in the mines and above ground in refuse banks has received consideration. A report has been puplished5/ describing apparatus and tests made on anthracite to determining the amount and composition of the oxidation products when normal dry air was passed through it at temperatures varying from 100° to 350° C. These tests showed that the amount of evolved gases and their relative prorortions varied with the temperature. From: these results, graphs were prepared by which `he temperature at which the coal was oxidized could 'be estimated, thus giving a possible means of detecting incipient heating.]

Jan 1, 1938

By G. S. Scott

[In the course of the investigation the Bureau of Mines is carrying on to determine the causes, behavior, and control of mine fires, the detection of incipient heating underground in the mines and above ground in refuse banks has received consideration. A report has been published5/ describing apparatus and tests made on anthracite to determine the amount and composition of the a oxidation products when normal dry air was passed through it at temperatures varrying from 100° to 350° C. These tests showed that the amount of evolved gases and their relative proportions varied with the temperature. From these results, graphs were prepared by which the temperature at which the coal was oxidized could be estimated thus giving a possible means of detecting incipient heating.]

Jan 1, 1938

By J. A. Herdlick

Under authority of the Strategic Materials Act of June 1939, the Federal Bureau of Mines, in cooperation with the Geological Survey, began a broad program of investigation of the strategically important chromite deposits in Sweetgrass, Stillwater, and Carbon Counties, Mont. Extensive occurrences of chromite along the Stillwater Complex in Stillwater County were investigated. The two principal deposits, The Mouat-Sampson and Benbow mines, ultimately were developed and placed in production by the Federal Government. As a part of this general development program, the Carbon County chromite deposits near Red Lodge were examined by Bureau of Mines engineers in 1940, and by the Geological Survey .1-1 1942. The district was examined earlier by Schafer, and the Four Chromes area is mentioned briefly by Westgate. Although the Red Ledge deposits were considered to be of minor importance as compared to those of the Stillwater Complex, several of the ore bodies were adaptable to open-pit mining' methods, and one large deposit on Line Creek Plateau was readily accessible to the Red Lodge-Cooke highway. In 1941, the U. 3. Vanadium Corp. began mining crude lump-chrome ore from the deposit on Line Creek Plateau to supplement national stockpiles, which were being depleted by the rearmament program and the disruption of chrome-ore imports by the European war. Access roads gore constricted to Hellroaring Plateau, and the mining operations were extended to that area. A gravity concentrator with a capacity of 200 tons per day was built and operated at Red Lodge to beneficiate lower-grade ore from the district.

Jan 1, 1948

By RV. Ramanl, KV. K. Prasad, M. Swaminathan

The objective of the research in this project is to develop a knowledge based expert system for aiding the planning of mine ventilation systems. This system focuses on mine ventilation system design from a coal mine dust control standpoint. It is recognized that mine ventilation system design is an engineering problem involving not only rote numerical calculations to solve the pressure quantity problem but also substantial judgement and expertise to analyze a problem situation and Interpret the results of an algorithmic program. The thrust of this project is to i) extract this knowledge from public domain sources and recognized experts in industry, government and academia, 11) represent this knowledge in the form of IF ... TI-IEN rules in an expert system (ES) and 111) interface the developed expert system with a mine ventilation network analysis program vis. PSUMVS (Pensylvania State University Mine Ventilation Simulator). By providing the numerical computing and qualitative reasoning aspects of mine ventilation system design in a single Integrated system, better quality decision support will be made available to apprentice users.

Jan 1, 1988

By Leon W. Dupuy

"INTRODUCTION Scheelite occurring in tactite at the Black Rock tungsten mine, near Benton in Mono County, Calif., was investigated by the Bureau of Mines in cooperation with the Geological Survey as part of their search for additional sources of supply of strategic minerals authorized under the Strategic Materials Act. 3/4/The work accomplished by the Bureau, and the assays of samples taken are described in this manuscript. The ore found aided materially in prolonging the operating life of the mine during the recent national emergency, supplying much-needed tungsten for war use. ACKNOWLEDGMENTSIn its program of investigations of mineral deposits, the Bureau of Mines has as its primary objective the more efficient utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, under the direction of Lowell B. Moon, chief, conducts preliminary examinations, performs the actual development work, and prepares the final report. The Metallurgical Division, under the direction of C. C. Ralston, chief, analyzes samples and performs beneficiatibn tests."

Mar 1, 1948

By R. Hogg, T. F. Dumm

"Procedures for particle size analysis on respirable dust from coal mines have been evaluated. Using respirable dusts dispersed in a laboratory dust chamber, size distributions measured using cascade impactors have been compared with the results of a variety of laboratory sizing methods performed on samples collected on filters placed side-by-side with the impactors. The laboratory techniques included centrifugal sedimentation, laser diffraction/scattering and automatic particle counting. The general agreement among the various methods was very good, with systematic differences which can be attributed to the different definitions of size used. Simple conversion factors have been obtained which can be used to transform the laboratory data to equivalent aerodynamic sizes.Similar comparisons have been made on samples collected in underground coal mines. Again, the results are in quite good agreement although small discrepancies were observed in· some cases. These have been attributed to some degree of agglomeration in the airborne dust, leading to slightly coarser apparent distributions in the impactor samples INTRODUCTIONA primary goal of mine ventilation is the control of airborne dust, especially in the ""respirable"" size range, typically defined as finer than about 5 to 10 µm. It follows that determination of the amount and characteristics of the respirable dust is an important factor in evaluating the performance of ventilation systems. Particle size information on airborne dust in mines is commonly obtained by in- situ measurements using cascade impactors. However, these tend to be inconvenient for routine data collection and the alternative approach of collecting samples in the mine, on filters for example, and returning them to the laboratory for detailed analysis is very attractive. Questions have often been raised, on the other hand, as to the appropriateness of this approach. How well · do such laboratory methods describe the distribution of aerodynamic diameter of the airborne dust particles in the mine environment? The purpose of the work described in this paper was to evaluate some laboratory sizing methods and to compare the results of such measurements with the size data obtained by the direct, in-situ method."

Jan 1, 1989

By Albert E. Long

To date the commercial diamond bit setters have been principally interested in the speed with which they could produce a sharp, fast-cutting bit. Thus, a premium has been placed on setters who combine a high degree of manual dexterity with the ability quickly to select the Sharp points and edges of the diamonds and set them in the mold without lost motion. The premium on speed does not allow the setters the time, nor are they trained, to consider also the crystallographic structures of the diamonds which are the clues indicating the harder and more suitable working surfaces. Since early fall of 1949, the Bureau of Mines has been conducting a long-range series of experiments in which drill bort have been oriented in diamond bits in an effort to determine the effects and economic practicability of utilizing the hardest surfaces of the diamond crystal structure. The preliminary experiments completed to date indicate that a substantial saving in diamonds may be affected by using the harder areas of the diamonds as working surfaces in the crown of diamond bits. The experimental work is being conducted by the Bureau of Mines in the laboratories and full-scale mine of the Mining Research Branch, Minerals Technology Division, Region VIII, of the U. S. Bureau of Mines at the Mount Weather Station, Bluemont, Va.

Jan 1, 1951

By R. E. Brewer

Published investigations show that many different chemical reagents have been used in determining the constitution of coals , but only a few studies have been applied directly in evaluating the effects of such reagents on the carbonization products of coal , Most of the treatments have been so drastic that any permissible conclusions that may be drawn are inferential in respect to any favorable effects on the yields and composition of the usual carbonization products .

Sep 1, 1943

By John E. Miller

Supercompressibility factors, Fpv, were derived from experimental compressibility data for five helium-nitrogen mixtures containing from 50 to 100 pct helium. These Fpv values are required as volumetric correction factors for or if ice meter measurement of "crude helium" (helium-nitrogen) purchased by the Government in a program of helium conservation. Although compressibility measurements were made by the Burnett method (2)3 - for pressures from 100 to 3,400 psia and temperatures from 40° to 100° F, Fpv values were needed only for pressures from 400 to 2,000 psia. Consequently, values at increments of 2° F, 2 pct helium, and 10 psia were tabulated only for the required pressure range. Values for pressures outside this range can be calculated from information shown in the tables. Values for the second, third, and fourth coefficients in the equation Z = 1 + BP + CP2 + DP3 are also included.

Jan 1, 1963

By A. R. Taylor

This report describes the design, construction, and operation of a low temperature adiabatic calorimeter for measuring heat capacities of solids or liquids from 60° to 300° K. A brief discussion of the basic theory involved in chemical thermodynamics and the problems involved in obtaining accurate experimental data is presented. The operation of the calorimeter was tested by measuring the heat capacity of a sample of benzoic acid obtained from the National Bureau of Standards over a temperature range of 60° to 300° K. The measured heat capacity values of the benzoic acid compared favorably with similar values obtained by the Bureau of Standards, the maximum deviation being 0.5 percent. THEORY A brief discussion of the basic theory involved in chemical thermodynamics will illustrate the applications of heat capacity data and the problems involved in obtaining accurate experimental data.

Jan 1, 1962

By W. H. Coghill, B. W. Gandrud, F. D. DeVaney

"The self-fluxing iron ores of Alabama are the foundation of the thriving iron and steel industry of that State. In addition to these deposits of self fluxing ores there are seams containing practically the same percentages of iron but too much silica. These ores at present are valueless, but if they could be concentrated by reducing the silica content, the ore reserves of the Birmingham district would be greatly augmented. A detailed report on the iron-ore deposits of the district, describing the types of ore and their extent, has been published.In forwarding its mineral conservation policies the United States Bureau of Mines has given some attention to the siliceous ores of this district.The low cost of gravity concentration gives this process first rank in the beneficiation of iron ores. For this reason many experimenters have tried to concentrate the Alabama iron ores on tables. In the face of the early failures a new trial has been made and the results have justified the effort.In this work more attention than formerly has been given to the physical, properties of the ores. The removable siliceous gangue is in the form of oolitic grains which ""shell"" out like corn, leaving the hematite as rich high-grade ""slime"" and as clean granular grains. The ""slime concentrate"" may be recovered by well known desliming processes. The oolitic grains and granular hematite are separated on tables."

May 1, 1929

By O. C. Blade

Consumption of Diesel fuel oil in the United States has increased very rapidly during recent years. At the present time approximately 5 percent of the crude oil refined in this country is said to be processed for this purpose. This figure represents approximately 20 percent of the total distillate-type fuel oils now being produced in the United States. One factor contributing greatly to the recent increase in consumption of Diesel fuel oil has been the conversion from steam locomotives to Diesel engines by a number of railroads. Other contributing factors are greFl.ter use of Diesel engine8 in buses, trucks, tractors, water craft, and stationary power plants. The growing importance of Diesel fuel oil has resulted in a need by the petroleum industry, engine manufacturers, and consumers for more information regarding the types and quality of Diesel fuels currently being marketed. To supply this information, the American Petroleum Institute and the Bureau of Mines, United states Department of the Interior, under a cooperative agreement, have conducted a survey of Diesel fuel all produced in refineries in this country during 1950. Under the agreements, samples of Diesel fuel oil, representative of actual shipments, were analyzed by the manufacturers in accordance with instructions issued by the Fuel Survey Panel of the Automotive Research Committee of the American Petroleum Institute. Results of the analyses were transmitted to the Bureau of Mines, and that agency has studied the data and compiled them by groups in comparable form as shown in the tables of this report.

Jan 1, 1950

By Thomas W. Camm

In this U.S. Bureau of Mines report, mine and mill cost models are presented to make quick estimates of the cost to develop mineral deposits in the desert region of the Southwest United States. Regression analysis was used to generate capital and operating cost equations for each model in the form Y = AXB, where Y is the cost estimated and X is the assumed daily capacity in short tons. A and B are constants determined by the regression analysis. Each is broken down into 11 subcategories to facilitate escalation of costs for inflation and to increase their versatility in economic evaluation work. This report contains 2 open pit models, 6 underground mine models, 11 mill models, and cost equations for access roads, powerlines, and tailings ponds. In addition, adjustment factors for variation in haulage distances are provided for open pit models and variation in mining depths for underground models.

Jan 1, 1991

By G. W. Jones

Gas analysis is of great practical value to the combustion engineer as a guide in the proper deli and operation of power and heating plants. The automotive industry, however, has made little use of gas analysis in the design and construction of engines. Tests4 made by the Bureau of Mines have shorn that for the average motor vehicle approximately 30 per cent of the heat value of the gasoline passes out in the exhaust as incomplete-combustion products. The tendency at present is to pay more attention to ease and flexibility of operation than to efficiency of combustion. However, neither condition can be fully realized except where each cylinder gets a mixture of the same composition - that is, when certain cylinders do not "load up" with gas at the expense of the others. When this occurs, due to some of the cylinders having too rich a mixture while in others it is too lean, it is impossible to get efficient combustion from the fuel used. Gas analysis enables the engineer to determine the quality of the mixture fed to the different cylinders with a high degree of precision. Briefly, the method consists in making an analysis of the exhaust gas from each cylinder while the engine is in operation.

Jan 1, 1924

By Jerry A. Wichser

A series of linear programmed instruction modules was developed in the general subject areas of Blasting Technology & Explosives Safety & Electrical Training. The linear programs (modules) were developed in the form of tape-slide plus workbook materials, while the branching format evolved from the LTS teaching machine system from MIT, through several other teaching machines and micro-computers, finally settling on Radio Shack TRS-80 microcomputers, Models I & III. Initial validation figures indicate that essentially the same result, are attained from both methods (based on pre and post test scores), with the most noticeable difference being an approximately 25% savings in study time with the branching modules. In December 1980, the development of modules on High-Voltage Training, Trolley Wireman Training, and Compressed Gas Safety was added to the overall tasks of the contract.

Jan 1, 1984

By Raymond J. Isherwood

The U. S. Bureau of Mines has investigated the domestic primary and secondary lead smelting and refining industries to determine the economic impacts of existing and proposed environmental, health, and safety regulations. The impacts are assessed in terms of capital and operating costs for existing and alternative smelting/ refining technologies. Industry response to regulatory implementation is estimated and quantified in terms of import value from lost lead production. For the primary lead industry, regulatory compliance may add up to 1.15 ¢/lb refined lead to operating cost for rehabilitated plants. Alternative smelting/refining methods could reduce net operating costs by as much as 4.36 ¢/lb refined lead. Capital expenditures would vary from $750 to $1,000 per annual mt of smelter capacity. Secondary lead smelter operating costs would increase about 3.8 ¢/lb refined lead to comply with existing regulations. Capital expenditures would average about $124 per annual mt of smelter capacity. Implementation and enforcement of proposed regulations would result in closure of the primary lead industry and additional expenditures for compliance by the secondary lead industry. Enforcement of the most extreme proposed regulations would force the secondary lead industry to close.

Jan 1, 1988

By W. G. Pariseau

A U.S. Bureau of Mines case study of pillar recovery in high-grade ore near the Ross shaft at, the Homestake Mine, Lead, SD, has demonstrated the usefulness of the finite-clement method for the evaluation of shaft pillar mining plans and shaft stability. This report, one of three in a series describing the Ross shaft pillar case study, focuses on the premining stability analysis. The two-dimensional computer program UTAH2 was used in advance of pillar mining; results suggested that the shaft would remain stable. Subsequent reports describe parts 2 and 3 of the study. In part 2, borehole extensometers and other instruments were installed to provide data for model verification and shaft monitoring. Results of the recalibrated two-dimensional model confirmed the premining stability evaluation. However, after mining began, great concern developed because of the appearance of cracks and other signs of ground movement over considerable distances from the area of active pillar miping. In part 3, an intense three-dimensional modeling effort using UTAH3 was initiated. The results again showed that the shaft would remain safe. Three-dimensional analyses of alternative pillar mining scenarios indicated that more of the shaft pillar ore reserve could be recovered than previously thought.

Jan 1, 2010

By Raghoottma S. Pandurangi, Mohindar S. Seehra, Pedro Bolsait, Bronwyn L. Razzaboni

"Surface IR (infrared) modes of crystalline and fumed (amorphous) silica particles, calcined at temperatures up to 1095°C, have been studied by Fourier transform infrared spectroscopy. The ability of these same particles to lyse cells has been measured by a hemolysis protocol. The untreated crystalline and amorphous materials differ by a factor of 40 in specific surface area, and the intensity per unit mass of the sharp surface silanol band near 3745 cm-1 in the amorphous material is an order of magnitude larger than in the crystalline material. A similar difference is observed in the lysing potential of the two materials. The intensity of the silanol band increases after calcination for both materials, reaching peak values near 500°C, followed by a dramatic drop at higher calcination temperatures, and reaching negligible values for materials calcined near 1100°C. The lysing potential data follow essentially the same pattern for both crystalline and fumed silica. These results are consistent with the hypothesis that the surface silanol groups are involved in cell lysis. Further experiments are suggested to evaluate the relationship between the surface structure of ailica particles and their potential cytotoxicity. IntroductionThe characterization of the surface structure of various allotropic forms of silica is of interest because the cytotoxicity of silica particles of respirable size has been commonly related to the chemical interaction of functional groups on the surface of such particles with the lipoproteins contained in cell membranes (1-3). It has been found that the cytotoxic potential of silica particles varies greatly with their crystalline structure (4,5), particle size (6-8), surface composition (9), and molecular surface configuration (1,10). Studies of the infrared (IR) modes of various forms of silica have been reported by a number of researchers (3 ,11-19). Several books and reviews (20-24) have dealt with the identification of functional groups on silica surfaces and the effect of heat treatment on the surface structure. The nature of the surface is said to be critical in determining the biological activity of silica dusts (3).Fourier transform infrared (FTIR) spectroscopy is a highly sensitive ·technique for identifying IR surface modes of tine particulates, and it was deemed of interest to examine the surface structure and its relation to lysing potential of two widely different types of respirable silica dust. The lysing potential of respirable dust particles has been considered a first-level test for potential cytotoxicity."

Jan 1, 1990

By H. W. Wainwright

1. A schematic diagram and a description of the apparatus are presented. 2. Five runs were made using gas having a hydrogen-carbon monoxide ratio of about 2:1 and sulfur concentrations ranging from nil to 1.53 grains per 100 std. c.f. 3. At constant space velocity of synthesis gas the product of the sulfur concentration and days of operation, with conversion of H2 + CO above 97 percent, was constant. With a gas containing 0.04 grain of sulfur ac carbonyl sulfide per 100 std, cu. ft ,, the conversion of H2 + CO remained over 97 percent for 40 days. During that time the heating value of the product gas (on a C02-free basis) remained relatively constant at 940 B .t .u. per c.f., based on dry gas measured at 600 F. and 30 inches Hg.

Jan 1, 1954