Search Documents

The coal-bearing regions of Colorado cover approximately 29,600 square miles, which is 28.4 percent of the state's total area. The most important coal-bearing regions are located in the north western and west-central parts of Colorado. Coal resources vary from lignite to anthracite. More than 70 percent are bituminous; 23 percent subbituminous; 5 percent lignite; and less than 1 percent anthracite. The state's coal reserves total about 17.2 billion tons, 3.5 percent of national reserves. Approximately 8.8 million acres of coal rights in the state are owned by the Federal Government; on about 72percent of this land, the Federal Government controls both the coal and the surface rights. It is estimated that approximately 4.2 billion tons of coal reserves are under federal ownership in Colorado. Permitted acreage of mines in Colorado ranges from 40 to 13,114 acres. Differences in elevation create many climatic zones in Colorado. Local annual precipitation can average less than eight inches in some areas in extreme western Colorado to more than 30 inches in certain mountainous areas. Generally, precipitation rates are low at most mine sites, making revegetation difficult. Colorado gained primacy when its regulatory program was conditionally approved December 15,1980. The Abandoned Mine Land Program was approved June 11, 1982.

Jan 1, 1992

By William C. Cooley

A review was made of two Russian books and a chapter from a third book dealing with pipeline transport of coal. Emphasis was placed on hydrotransport of coarse coal in underground mines or surface pipelines. The books reviewed were: "Means of Increasing the Effectiveness of Hydrotransport," by V. N. Pokrovskaya (1972), "Parameters and Modes of Hydraulic Transport of Coal" by V. V. Traynis (1970), and the chapter "Calculations of Hydrotransport of Useful Minerals and Waste Rock" from the book "Hydromechanization of Opencast Workings" by G. A. Nurok (1970). All three are unique and useful additions to the world literature on hydrotransport. The Traynis book reveals the development and results of circular wheel stand tests to simulate hydrotransport in horizontal pipes, which is a potentially outstanding contribution to slurry pipeline technology. Graphical data and equations are presented which suggest that headlosses for coarse coal can be predicted with good accuracy for pipe sizes up to 14 inches in diameter. Wheel stands permit tests for pipe wear and lump degradation without recycling coal through pumps. Recommendations are made for wheel stand tests and for correlation of existing data.

Jan 1, 1976

By Richard Stayner

Suspended seats perform two functions: Reduce effect of occasional large bumps; Reduce more continuous vibration at a lower level. The former needs high damping. The latter needs low damping. For most mobile work machines the inevitable compromise is generally better than a simple cushion seat, because that amplifies vibration at around 4 Hz which is a sensitive frequency for human vertical WBV. Why have standard tests for seat suspensions? • Seat suspensions are non-linear so any measure of performance depends on operating conditions. For comparison these need to be defined. • Seat manufacturers need benchmarks for product development; • Machine makers choose dynamic characteristics appropriate to their products; • Occupational health specialists wish to control operator exposure to Standard tests should be representative, repeatable and reproducible. These requirements are reviewed in relation to the history of seat test standards and the current position. Current position and history The current position is that we have standard tests for seats for agricultural tractors, earthmoving machinery, industrial (fork-lift) trucks. These tests comprise measurement of vibration transmission and of the rate of damping. Current standards developed as the technology developed, starting around 1960: 1. Test on machine driven over standard surface1. 2. Test on shaker reproducing standard surface. 3. Shaker input replaced by representative spectrum2. 4. Human subject replaced by dynamic dummy. (Not yet settled). Are standard tests representative? The development process has gradually moved seat tests further from reality. 4 hr samples of work exposure suggest that seats do not on average provide large reductions of vertical WBV3. For specific magnitudes of vibration they can work well. For low vibration, performance is reduced by friction and for severe vibration by length of travel. Recent work has led to a new test to quantify how a suspension controls over-travel 9.

Jan 6, 2006

By Frank C. Morris

This report presents the results of a Bureau of Mines study to identify clays found in several petroleum-reservoir rocks in the Tejon-Grapevine area, Kern County, Calif., and to determine the effect of water sensitivity of the clays on the permeability of the reservoir rocks. The clays in the porous rocks were examined in detail, and the clay-mineral types were identified by differential thermal analysis, X-ray diffraction, and optical and dye-staining methods. Fresh-water damage to the permeability of the oil-reservoir rocks was indicated by a study of 125 core samples from productive formations. The study indicated that, although clays were generally less than 5 percent of the reservoir rocks, they swelled in water, particularly fresh water, and nearly blocked the flow channels through which oil flows to the well, effectively reducing the permeability of the formations. The average permeability of rock decreased from 1,600 millidarcys in air to 620 millidarcys in salt water and 120 millidarcys in fresh water. The dominant clays in the oil-bearing sandstones were members of the montmorillonite group. They were associated with smaller quantities of clays found to be in the mica or illite group. None of the cores appeared to contain clays of the kaolinite group. In the lower section of the J.V. sandstone indications of what appeared to be the mineral sepiolite were noted.

Jan 1, 1959

By Clinton C. Knox

Attention of mine operators and engineers in the Picher zinc-lead field has been drawn increasingly in recent years to marginal ore deposits lying at greater than normal depth below surface in the marked structural depressions known as the Miami and Bendelari troughs. Not only mining but prospect and development drilling is relatively costly in the bottoms of the structural depressions known as the. Miami and Bendelari troughs which cross the center of the Picher field. Nevertheless, operations by various mining companies in recent years have shown that no insuperable problems exist, and with the gradual lowering of grade cut-offs throughout the field, certain potential deep-ore areas, previously only partly explored seemed worthy of further investigation. Some such areas were called to the attention of Bureau of Mines engineers by lease holders and operators, while others were noted in the course of Bureau's systematic investigation of Tri-State ore reserves. The writer was assigned to make a study of. those possible "trough extensions," in the course of which all available nine maps, drill logs, and prior reports were assembled. Subsequently 41 churn drill holes were bored by the Bureau in the periods October 1944 to May 1945 and October 1946 to April 1947. The general area under investigation this project is indicated on figure 1, which likewise shows its relation to nearby towns, roads, and railroads. The location of individual deposits included in the report is indicated more clearly on figure 3. Minable ore was found in only two holes, and the structural information procured by drilling was less encouraging than anticipated. This report, however, presents all factual data obtained, in the belief that they may be useful in subsequent prospecting and development projects in the areas investigated. There are also set forth some of the stratigraphic data relative to the Picher field ns a whole and the Miami and Bendelari troughs which were assembled in the preliminary investigation of this project.

Jan 1, 1949

By G. W. Birge

Carbonizing properties of the principal coal beds of Perry County, Ky., are described in this Bureau of Mines report. Seven samples, representing the Hindman, Flag, Haddix, and Fire Clay beds, were carbonized by the Bureau of Mines-American Gas Association (BM-AGA) method, and yields of products and physical properties of cokes were determined. Carbonizing properties of blends of Flag and Fire Clay coals, with 20 and 30 percent Pocahontas No. 3 low-volatile coal from McDowell County, W. Va., also were determined. Expanding properties of the Flag and Fire Clay coals and their blends were determined in the Bureau of Mines sole-heated oven. The Perry County coals tested are high-volatile A bituminous in rank and, with the exception of the Hindman-bed sample, which contained excessive sulfur, were chemically suitable for metallurgical use. The three coals tested in the sole-heated oven contracted less than normal for Appalachian coals of similar rank, Blending the Fire Clay and Flag coals with 20 or 30 percent low-volatile coal increased coke strength appreciably but increased the expansion beyond normal limits for industrial blends.

Jan 1, 1962

By G. R. Hopkins

The petroleum-refining industry established a. new record in fuel effieciency at refineries in 1936, when 597,000 B. t. u. of heat mere required to refine a barrel of crude oil, compared with an average of 615,000 B. t. u. in 1935 (see fig. 1). The principal factor in the 'indicated gain in fuel efficiency at refineries in 1936 was an increase in crude runs of 11 percent over 1935. A large part of the heat utilized at refineries is consumed elsewhere than under stills, or in ways quite independent of crude-oil distillation. In other words, as the operating ratio ( crude runs divided by capacity) for re- fineries increases toward tine maximum of 100 percent, the fuel requirements show progressively smaller increases and the average B. t. u. consumption per barrel of crude refined declines.

Jan 1, 1938

By J. H. Rose

This paper describing the milling practice at the Magma Copper Co., Superior, Ariz., is one of a series being prepared by the Bureau of Mines on milling methods and costs in the various mining districts throughout the United States. ACKNOWLEDGMENT The authors wish to acknowledge their indebtedness to William Koerner, general manager of the Magma Copper Co., for permission to prepare this article; to J. S. Garrott, former mill superintendent, for the historical facts; and to Walter Cooksley, general foreman, for his assistance in obtaining the data.

Jan 1, 1930

By W. C. Phalan

"Prewar Conditions:Metallic magnesium may be considered a war metal, but a war metal with a future, so far as the industry in the United States is concerned. Its production in the United States prior to 1915, on a commercial scale, was negligible, but imports prior to that year may be taken as a gaze of the demand for the metal. Unfortunately, magnesium was not listed separately by the Department of Commerce prior to the war, among the importations, but was included with other metals, as follows: ""Barium, calcium, magnesium, sodium, and potassium, and alloys of which said metals are the component materials of chief value."" However, the imports of metals enumerated other than magnesium were probably small, so that the importations under the above caption may be considered chiefly metallic magnesium in one form or another and, therefore, is an approximate gage of the demand for the metal in the United States. These imports were as follows:These figures are so close that they give a good idea of the figures for the respective calendar years.Of this prewar use, it has been estimated that about 85 per cent was used annually and in approximately equal quantities in the production of (1) flash-light powder, (2) fire works, (3) aluminum casting work, and (4) nickel and nickel-copper alleys, such as monel metal, etc. The re¬maining 15 per cent was employed for general uses, such as deoxiding brass and other copper alloys in foundry work, and to a small extent in laboratory and research work."

May 1, 1920

By J. J. Dowd

1. The Pittsburgh bed is the most important bed in Brooke County and virtually the entire production of coal in the county comes from this bed. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated at 191 million short tons as of January 1, 1954. Of this total, 190 million short tons are in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

Reduce respirable dust exposure of workmen operating auger-type continuous mining machines. Approach: An auger miner was fitted with an exhaust system which draws dust laden air through a [scruber] and discharges it behind the line curtain. How It Works: Dusty air is drawn into the space above the coal conveyor and through a scrubber, by two fans mounted side by side above the conveyor. Exhaust from the fans passes through a duct to the side of the auger miner, and into tubing that runs back and into the air return passage formed by the line curtain. See Figure 1. Of the 5,000 cubic feet per minute of air normally entering the working place, 4/5 is drawn out through the dust exhaust system. The system was installed on a Wilcox Mark 20 Miner and tested underground by personnel of the Bureau's Pittsburgh, Pa., Mining and Safety Research Center, under a cost sharing

Jan 1, 1976

By E. P. Youngman

This paper is one of a series of digests of foreign mining legislation and court decisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines" in various foreign countries. In the preparation of this interpretation of the laws of Norway, use has been made of William R. Orrmins' translations of various acts of the Norwegian Government, which were forwarded from the American consulate at Oslo^ and transmitted to the Bureau of Mines through the courtesy of the State Department. This digest is released subject to amplification and correction, if necessary, by the proper American foreignservice officers.

Nov 1, 1932

By Don Conrad, Tom Friend, Bill Wiehagen, Lynn Rethi

On-the-job training (OJT) is a very common method of teaching job skills. Much of the training is done by experienced workers. This paper discusses small investments that can help improve the effectiveness of OJT. Effective OJT involves some structure and planning in the transfer of responsibility for task performance from the trainer to the novice. Assisting the OJT trainer could involve helping develop up-to-date job analyses and offering strategies for teaching and evaluating job skills. The scope of this paper addresses (1) organizational considerations supporting structured OJT, (2) general strategies for structuring OJT, (3) a typical approach for conducting OJT, (4) characteristics and duties of OJT trainers, and (5) limitations of OJT as a teaching method. Health, safety, and operational skills can be connected through training. Haul truck operator training is used to illustrate some of the concepts discussed in this paper.

Jan 1, 2002

By Albert J. Rambosek

The results obtained in a study of the stress conditions existing in a drill bit-point area and in the underlying rock, when the bit was in full but nonpenetrative contact with the rock, are presented. This investigation by the Bureau of Mines was the preliminary exploratory phase of a long-range program of research on rock drilling to establish criteria for the maximum economically feasible rate of rock penetration. The photoelastic technique of experimental stress analysis was the principal method used to obtain the data. Transparent models and transmitted light were employed to investigate patterns in drill-bit models and isotropic materials under the bit when subjected to a concentrated static load. Comparative stress data for anisotropic rock were obtained by the reflective photoelastic technique. Brittle lacquer and an extensometer were used obtain supplementary information wherever substantiating data were desired to check photoelastic results. The zone of maximum shear occurs along an arc near the contact face of the bit. The stress distribution pattern in an isotropic model rock near the area contacted by the bit was nearly a mirror image of that exhibited within a similar areal zone of the bit. The stress pattern in granodiorite specimens was similar, though not symmetric, to the pattern in the isotropic model rock. The asymmetry of the stress pattern in the granodiorite was attributed to the anisotropic characteristics of the constituent minerals of various sizes.

Jan 1, 1963

By George Quackenbos

The principal objective of this Program is the design, fabrication and testing of an Environmental System for operation in underground mines, to assess the effect of various mining systems on the contaminant levels near the mine face and within return airways. In order to determine the effect on airborne contamination in mines resulting from the development of new mining techniques, equipment and control systems, a Comprehensive Monitoring System is required to assess such contamination levels at critical and strategic locations and relate this information with ventilation parameters. The three variables to be sensed on a continuous basis are airborne dust concentration, methane concentration and ventilation air velocity. Each Monitoring Station will consist of a self-contained unit containing a power source and sensors to monitor the three above mentioned parameters. Ruggedness, reliability, ease 'of operation and intrinsic safety are important design objectives. Data gathered by each Monitoring Station will be fed to a Central Data Acquisition System by means of a portable transfer unit.

Jan 1, 1982

By Les A. Beckett

The Bureau of Mines has developed MULSIM/BM, an improved computer program using the boundary-element approach for geomechanical analysis of mine plans in single or multiple coal seams. This Information Circular presents the improved features of the MULSIN/BM program. The four major improvements are the following: (1) Ability to specify up to 26 material property sets. (2) A new material model capability for gob and inserted materials such as packwalls or cribs. (3) Ability to model a large area with a grid of undivided blocks and to subdivide only a specified fine-mesh portion of these blocks into elements. (4) Specification of extraction ratios for the undivided blocks. In addition, an interactive graphics mesh generator program was written to accompany MULSIM/BM. A complete user's guide and program listings are included within the appendixes. The MULSIM/BM and mesh generator programs are available on tape from the National Technical Information Service.3

Jan 1, 1988

By John A. Johnson

The first report of investigations5/ in this series pertaining to the investigation of stemming at the Mount Weather testing adit dealt with dust produced from blasting. The present report discussed the effect of stemming on eases generated by blasting, describes the test procedure, and analyzes the results from, blasting 61 standard rounds. Following care the types of stemming that are being investigated: 1, No stemming. 2. Sand in 2 paper cartridges. Clay in 2 paper cartridges. Commercial hydrated lira in 2 paper cartridges. 5. Combustible blasting plugs. 6. Ceramic is blasting plugs with clay in 2 paper cartridges.

Jan 1, 1940

By John A. Johnson

The first report of investigations5/ in this series pertaining to the investigation of stemming at the Mount Weather testing adit dealt with dust produced from blasting. The present report discusses the effect of stemming on eases generated by blasting, describes the test procedure, and analyzes the results from, blasting 61 standard rounds. Following care the types of stemming that -,re being investigated: 1, No stemming. 2. Sand in 2 paper cartridges. 3. Clay in 2 paper cartridges. 4. Commercial hydrated lime in 2 paper cartridges. 5. Combustible blasting plugs. 6. Ceramic is blasting plugs with clay in 2 paper cartridges.

Jan 1, 1940

By C. H. Fisher, M. L. Fein, A. Eisner, G. C. Sprunk, Loyal Clarke, H. H. Storch

"The large reserves of low-rank coals in the western United States are at a disadvantage in competing with the more mature but less plentiful eastern coals, which are nearer important markets and are more suitable for combustion and coke production. However, low-rank coals generally are amenable to hydrogenation, and the western coals might become an important source of liquid fuels and organic chemicals when petroleum is less plentiful.In view of these facts an the tremendous quantities available, further information on the western coals clearly desirable. The purpose of the work described in this paper was to study the hydrogenation characteristics of some of the low-rank western coals in discontinuous converters. The data obtained in this manner, which are inadequate for predicting the suitability of coals for large-scale continuous hydrogenation, were used as a basis for selecting samples for further study in the Bureau's experimental coal-hydrogenation plant (26, 35). 8/ Because of the general importance of the western coals and recently demonstrated relation between coal hydrogenation and petrograghy (14, 15, 16), the proportions of anthraxylon, (vitrain), translucent attritus, and opaque matter were determined. In some instances samples of anthraxylon were isolated and hydrogenated separately so that their properties might be compared with those of the entire coal. The samples studied include peat, brown coal, lignite, sub-bituminous coals, and low-rank bituminous coals."

Mar 1, 1940

USBM Contract H0133045 consists of the design, build and test of 50 waveform generators. The waveform generator is a small ULF transmitter operating in the 1 to 3 KHz frequency range for the purpose of locating trapped miners during a mine disaster. This contract provided for the design, test, and building of 50 waveform generators using a discrete component construction with an option of using hybrid construction techniques within 105 days after the effective date of the contract. Because of large quantity economic considerations, this option was not initiated. Two engineering models were designed, constructed and tested and 50 final production units were fabricated using discrete construction. Complete documentation is supplied under a separate package which includes final schematics, parts list, layout information, equipment specification, production test procedures and qualification test procedures. Ten units have been delivered to the USBM. The remaining 40 units are being retained for packaging under contract H0242010 Transmitter Package and Receivers. A great deal of experience has been gained as a result of this contract. A final discrete potted printed circuit configuration has been arrived at that is now ready for field testing. After field testing, any desired changes should be incorporated into a final design. However, as a result of the current experience gained building and testing the production units, this printed circuit package together with potting procedure could be improved to reduce future costs. For example, the printed circuit board could be increased in size by 0.125 to 0.2 inches and all components could be mounted directly to the board eliminating costly hand stacking of components. The new printed