Search Documents

By W. J. Boone

Experimental determinations were made of vapor-liquid equilibria data for a helium-nitrogen-methane system. A mixture composition was chosen to approximate the crude helium to be produced Or conservation that will eventually be further refined to obtain pure helium. Although there are publications of studies of the vapor-liquid equilibria of helium-nitrogen, helium-methane, and nitrogen-methane binary systems, there is little indication of work done on the ternary system of helium-nitrogen-methane. The experimental data presented in this report supplement the information available for the binary systems. The equilibrium vapor-liquid data and equilibrium vaporization coefficients are presented in tabular form. Graphs are employed to show an extensive amount of the data.

Jan 1, 1963

By Michael G. Zabetakis

THIS is a summary of the available limit of flammability, autoignition, and burning-rate data for more than 200 combustible gases and vapors in air and other oxidants, as well as of empirical rules and graphs that can be used to predict similar data for thousands of other combustibles under a variety of environmental conditions. Specific data are presented on the paraffinic, unsaturated, aromatic, and alicyclic hydrocarbons, alcohols, ethers, aldehydes, ketones, and sulfur compounds, and an assortment of fuels, fuel blends, hydraulic fluids, engine oils, and miscellaneous combustible gases and vapors.

Jan 1, 1965

By B. D. Nash

The object of this research was to investigate the technical feasibility of preparing chromium metal by the thermal decomposition of bisbenzene chromium. Bisbenzene chromium, a pi-bonded sandwich type organometallic compound, was thermally decomposed under reduced pressure to form a metal plate on a heated substrate. Metal recovery was close to 100 percent of theoretical, with deposition rates up to 20.8 mg/hr/cm2. Metal purity was dependent not only upon the purity of the starting material, but also upon the sublimation rate of bisbenzene chromium. Total detectable metallic impurities ranged from a low of 18 ppm to several hundred ppm. In general, metallic impurities were less than 100 ppm. Carbon, the major nonmetallic impurity, ranged from less than 0.3 percent to more than 10 percent. The carbon contamination is most likely a result of the decomposition of the organic portion of bisbenzene chromium. An unusual property of some of the deposits was their outstanding corrosion resistance. Unlike pure electrolytic chromium, which dissolves readily, these deposits were insoluble in hot mineral acids.

Jan 1, 1968

By Steven D. Wirch

Abandoned underground coal mine areas must either be sealed or ventilated to comply with federal mine regulations. Ventilation of these abandoned areas is often impractical due to roof falls and inadequate primary mine ventilation. If the area is sealed, a very complex ventilation system is set up. In which the gob "breathes" in and out due to barometric pressure fluctuations. The Gob Assistant is a computer program (for use on IBM compatible personal computers) which allows the prediction of air flows into and out of a sealed mine area. Gas flows with applicable control techniques are also modeled. This information is presented to the user who will decide which control technique, or combination of techniques will ultimately be applied. The Gob Assistant is an intelligent gob simulator that can reduce the guesswork involved in predicting the effects of sealing and control techniques before they are applied. This paper provides the fundamental principles upon which the Gob Assistant is based, verification of these principles, and an explanation of how these principles were integrated into the Gob Assistant.

Jan 1, 1988

By T. H. Dubaniewicz

Fiber-optic technology is progressing rapidly, including the development of fiber-optic sensors for many applications. These sensors have the advantages of high sensitivity, light weight, small size, high bandwidth, and freedom from electromagnetic influences. The U.S. Bureau of Mines is investigating the use of fiber-optic technology to monitor mine atmospheres. This report describes a methane monitor based on differential absorption of infrared light. The monitor can detect methane concentrations as low as 0.2 vol pct as far away as 2 km via fiber-optic cable. The upper range is 100 vol pct methane. Since the system requires no electrical power within the mine, it is intrinsically safe.

Jan 1, 2010

By J. R. Nettle

A method has been developed in the laboratory for successfully electro-refining titanium metal. Refining is accomplished in e fused-salt electrolyte using offgrade metal as the anode and collecting the purified metal at the cathode. The characteristics and requirements of the various alkali chlorides tested as electrolytes are discussed in relation to relative ease of purification and serviceability. The various types of cells designed and tested for electrorefining are illustrated and their method of operation discussed. The individual advantage of each cell and the purpose for which it was designed are reviewed. The magnitude of the cathode current density was found to depend largely upon the quantity of soluble titanium chloride in the electrolyte. The physical condition of the anode also greatly affected the cathode current density.

Jan 1, 1957

By R. D. Haynes

Coal, gas, and oil in many geological formations of the Eastern United States are intimately associated but have traditionally been recovered independently of each other. Oil and gas wells, however, are often spaced sufficiently close to cause the subsequent loss of up to 50 percent of the recoverable coal in the form of pillars or barriers left for mine safety purposes. A long-range planning technique was devised for exploiting oil and gas wells simultaneously with the mining of coal to recover the maximum fuel potential of the formations. Planned plugging of oil and gas wells, determined partly from production predictions via decline curve analysis, is coordinated with a mine development plan to achieve maximum coal recovery and reduce overall production losses of gas and oil due to plugging of the wells.

Jan 1, 1973

By William C. Cooley

This study Identifies and evaluates deposits of noncoal minerals in the U.S. which are most amenable to be mined underground hydraulically and transported hydraulically. A method was developed to screen and compare mineral deposits including economic comparisons. The most applicable minerals for hydraulic mining by borehole monitor jets from underground entries are soft uranium sandstones In Wyoming in locations where water is available. This method with hydrotransport could improve the safety, health and economy of underground uranium mining. Soft oil-bearing sandstones in California and Texas could be mined and transported by this method more safely than by other underground mining methods. Other weak sandstones may be hydraulically mined economically. Man, minerals are too hard to be mined by monitor jet but are amenable to hydraulic transport and hoisting. Uranium sandstone in New Mexico is of interest because of potentially improved health and safety in transport and lower transport cost, Increases in mine output for potash, in New Mexico and trona in Wyoming can be achieved most economically by adding hydraulic hoisting when existing skip capacity is at its limit. Research is recommended to obtain site-specific data on the feasibility of mining uranium ores by monitor jets.

Jan 1, 1981

By Robert M. Doerr

The research objective was to determine the effect of vanadium alloy additions on the oxidation behavior of cobalt-nickel Alloys. Eighteen alloys were reacted with 0 2 at 0.5 arm and 1,351°, 1,389°, and 1,429° K. The alloy compositions consisted of Co-Ni master alloys (0, 22, 50, 70, 91, and 100 wt pct Ni) with V additions of 0, 0.9, and 2.7 wt pct. Large early deviations from, or changes in, the parabolic rate constant were encountered, but the reaction rate in most cases declined approximately in accordance with the parabolic rate law. Relatively, the vanadium degraded the oxidation resistance most at the highest nickel contents. In some cases, melting of the oxide was inferred from microscopic evidence and X-ray diffraction measurements disclosed the presence of low-melting vanadates.

Jan 1, 1970

By J. L. Thompson

The U.S. Bureau of Mines conducted a water-jet-studies program using a single-bit, in-seam test unit to determine effects of a moderately high-pressure (up to 10,000 psi) water-jet-assisted cutting system on rock weakening. The in-seam test unit was used to obtain cutting force data in tangential, normal, and side force directions. Conical continuous miner and radial longwall miner bits were used to penetrate test samples of coalcrete, Berea sandstone, and Indiana limestone with unconfined compressive strengths of 4,600, 8,000 and 10,000 psi, respectively. Depth of cut in the coalcrete tests was 1 in, with 2-in cut spacing (2:1 ratio). Because of cutting equipment and instrumentation limitations, the Berea sandstone and Indiana lime-stone were cut using a 0.5-in depth of cut and 2-in spacing (4;1 ratio). Bit velocity was maintained at 25 ft/min for both bits. Each specimen and bit type was tested using 0.3-, 0.6-, 0.8-, and 1.0-mm-diam nozzles and water-jet pressures of 2,500, 5,000, 7,500, and 10,000 psig. Water-jet-assisted cutting decreased average resultant conical and radiallongwall bit cutting forces 6.4 and 8.4 pct in coalcrete, 5.5 and 1.4 pct in Berea sandstone, and 2.0 and 5.5 pct in Indiana limestone. Slight reductions of power requirements resulting from water-jet assist were ascertained during these experiments.

Jan 1, 1989

By Stephen P. Signer, John L. Lewis

This paper presents the results of a case study conducted in a two-entry gateroad in a coal mine where excessive roof deformation and bolt loading resulted in failure of many roof supports. The instruments consisted of 16 fully grouted, strain-gaged resin bolts, load cells on both full and partially grouted cable bolts, and vertical deflection multipoint extensometers. These instruments were installed on-cycle to measure loading on bolts in an existing support pattern and to determine if cable bolts could be used to improve roof stability. Results showed significant amounts of movement within the bolted zone. In some cases, these movements were enough to load the supports past their ultimate strength. Geology appeared to be a significant factor in localized roof degradation; that is, a very weak rock layer in the immediate roof overlain by a very strong rock layer contributed to the development of shear planes. Only one instrumented bolt had a maximum strain of less than 2,000 microstrain, which was the yield point of the steel. The average maximum strain on all bolts was 20,000 microstrain. However, electrical continuity to many gages was lost and a pattern was noted that would indicate possible bolt failure. Wire mesh and concrete cans installed as secondary support performed very effectively.

This volume contains a series of papers describing research conducted by the Bureau of Mines to develop or improve equipment and systems that satisfy the communication requirements of miners doing work related to rail, belt-conveyor, trackless, and hoist haulage systems.

Jan 1, 1977

By Bryan R. Carmenati

This report documents the need for formal health and safety, and equipment operations training in the mine construction industry. The outlines, objectives, and training texts were developed based on the recommendation of needs of mine construction personnel, and those of Dames and Moore (Safety Analysis of Shaft Sinking operations, 1977) and Kinton, Inc. (A Training Program for Conventional and Raise Drill Construction Personnel; Phase I, 1979). The training material samples contained herein (and under separate cover in its entirety) are designed to improve the safety and production of those in mine construction. An instructor-directed presentation is recommended. The results of the study are presented in the Findings and Recommendations section of this report.

Jan 1, 1982

By S. M. Shelton

Ferrograde manganese ore or its equivalent is essential to the manufacture of every ton of steel produced; although it is well-known that there are largo deposits of low-grade ore in the United States, production of substantial amounts of ferrograde material from domestic sources presents a problem that becomes more and more critical as the stock piled ore is depleted through inability to obtain adequate supplies from foreign sources. Consequently, a program of laboratory and pilot-plant investigations designed to solve the problem of obtaining a domestic supply of manganese has been undertaken by the Metallurgical Division, Bureau of Mines. This paper is one of a new series that will include reports of results obtained in the various investigations conducted under the manganese program. The scope of the program and the organization that was set up to direct and supervise the work were discussed in the foreword of the first paper of this series, Report of Investigations 3506, Manganese Investigations 1. Concentration of Manganese Ores from the Drum Mountain District, Utah, by S. R. Zimmerley, J. D. Vincent, and C. H. Schack. Other reports will be published as the work progresses.

Jan 1, 1942

By V. F. Parry

"INTRODUCTION During the war period the Bureau of Mines expanded its investigations on western coals principally in connection with Investigations of raw material resources for western steel production. Owing to the expansion of the steel industry, there was some concern regarding the availability of suitable coking coals; end because of the potential steel shortage, the production of sponge iron, using the lower-rank fuels, was considered. Work was conducted by the Bureau of Mines on exploration projects and on testing of coals both at the Central Experiment. Station at Pittsburgh, Pa., and at the Bureau of Mines Station at Golden, Cole.The results of these investigations are being published by the Bureau in several reports of investigations and technical papers. In making this resume of coal investigations, the work done by the Bureau of Mines at Pittsburgh in the Mining and Coal Carbonization Sections will be discussed and the investigations at Golden described in greater detail.INVESTIGATIONS OF WESTERN COALSThe Mining and Coal Carbonization Sections of the Coal Division, Bureau of Mines, under the supervision of A. L. Teeny es and J. D. Davis, respec¬tively, conducted many field investigations to locate and evaluate new sources of coking coals. Drilling explorations were made in Colorado, Wyoming, Utah, New Mexico, and Washington and revealed two important new reserves of coking coal. The first one studied was the Willow Creek bed at Kemmerer, Wyo., which was reported in 1945.3/ A recoverable reserve estimated at 11,200,000 tons was blocked out, and samples of coal were extracted for coking tests. The coking properties of the coal were not quite equal to those of Sunnyside coal, but it was indicated that a 50-percent blend of the Willow Creek with Lower Sunnyside will produce a satisfactory metallurgical coke based on Columbia steel standards."

Jan 1, 1948

By Jon C. Volkwein

The Bureau of Mines conducted a series of tests to evaluate the effectiveness of mixing a compressed-air-generated foam with dried whole-grain silica sand to suppress dust in minerals processing plants. Dust at downstream transfer points was monitored with personal gravimetric samplers and with Real-Time Aerosol Monitors (RAM's) that were connected to strip' chart recorders. Results showed dust reductions of 80 to 90 pct on three separate occasions at two different plants. The mechanism by which foam suppresses dust is discussed, as are the constraints on the use of foam, which may include incompatibility of the foam with the mineral product, difficulty in controlling the foam generator, and cost.

Jan 1, 1983

By David M. Gullikson

As part of its program of petroleum production research the Federal Bureau of Mines has long been engaged in the study and development of systems of analysis of oilfield waters (8, 12, 20, 21, 22, 27, 30).21 However, many of the early chemical procedures developed by the Bureau and widely adopted by the petroleum industry are time consuming, and some are unreliable for determining certain constituents found in California oilfield waters. Because of the need for more rapid and more accurate methods having greater sensitivity with low concentrations of some constituents, a study has been made by the Bureau's Petroleum Research Laboratory at San Francisco, in developing new techniques and modifying previously published techniques for analyzing oilfield waters by flame spectrophotometric, potentiometric, and colorimetric methods. Test solutions were synthesized for testing the suitability and accuracy of the procedures, and the effect of interfering ions. These solutions contained known quantities of characteristic constituents of oilfield waters including sodium, magnesium, potassium, calcium, lithium, strontium, barium, sulfate, chloride, bromide, iodide, carbonate, bicarbonate and borates in a wide range of concentrations. The compositions of these synthetic brines are listed in table 22. Many California oilfield waters contain salts of petroleum-derived organic acids and several synthetic oilfield waters also were prepared to which large quantities of naphthenates or salts of petroleum acids were added.

Jan 1, 1961

By A. G. Loomis

Although secondary-recovery methods have not been applied widely in California, it is apparent that increasing attention and effort must be given to this phase of recovery if the State is to maintain its high rank as a petroleum producer. Steadily increasing demands for petroleum products and decreasing rates of discovery of new oil fields and rapid depletion of existing reserves emphasize the prospect of an adverse situation of supply and demand in the not-far-distant future. If the trend of discoveries becomes more favorable or if more complete economic recovery of the oil in place can be obtained by secondary recovery, this situation can be averted. Not only are these reserves of economic importance to the petroleum industry to meet increasing market demands, but economic reclamation of such reserves is an important conservation measure, which will prolong the productive life of many fields" Accordingly, progressive operators in California are alert to the possibilities of secondary recovery and have done much to implement such operations wherever feasible. Most of the operations are of the pressure-maintenance type} in which the reservoir pressure is maintained or partly maintained by injecting natural gas to increase oil recovery. The possibilities of recovering additional oil from stripper fields by gas drive and water flooding (including water disposal) also are being tested in experimental field projects. Table 1 summarizes gas and water-injection projects in California.

Jan 1, 1952

By D. L. Paulson

The Bureau of Mines is investigating pyrometallurgical and chemical methods for extracting copper from sulfide ores under conditions that provide for control of gaseous and solid emissions. Under this program, a new electrothermic reduction process was developed to produce blister copper after collecting essentially all of the sulfur by a single-unit operation. The process feasibility was indicated by a laboratory-scale investigation that demonstrated chalcopyrite concentrate can be roasted to less than 1 percent sulfur and that the resulting calcine can be reduced with carbon to blister copper by a cyclic process in a single arc-smelting furnace. Pilot-scale tests in an 800-kV-A electric-arc furnace demonstrated that 98.4 pct of the contained copper can be continuously recovered as metal by operating at bath temperatures between 1,350° and 1,375° C. Smelting rates of approximately 225 lb of blend ft2 of bath surface/hr resulted in power consumptions of approximately 520 kW-hr/ton of blend. The blister copper that was produced contained less than 0.1 pct iron while the precious metals reporting to the copper product and gangue material elimination were similar to those in a conventional smelting operation.

Jan 1, 1976

By Robert L. Lagace

The purpose of the work reported herein was to investigate whether available telephone multiplexing equipment offered a means to rapidly upgrade the traffic-handling capacity of present mine telephone systems and provide for selective calling for safer and more efficient mine operation. Common sense was used to decide whether or not an item could be termed "available." Since conventional telephone gear is not designed to interface pager phones for example, existing shelf items would require adapters to compatibly interface these two types of gear for independent operation over the present single twisted pair used in mines. These and similar small items were allowed, but if a system required any extensive design work to adapt it for the mines, we ruled it "not available."

Jan 1, 1975