Search Documents

By Elzbieta Mielczarski, Jerzy Mielczarski, Jan Drzymala, Yann Duvalm

Polyethylene glycol monoalkyl ethers (CnEm) render quartz hydrophobic while feldspar remains hydrophilic. As a result quartz can be separated from feldspar in small frothless flotation devices such as the Hallimond tube. The separation can be accomplished at room temperature at pH < 7 and C16E33 concentrations between 10-5 and 10-4 M for quartz particles smaller than 0.4 mm. No separation is observed when feldspar ore containing about 60 % of feldspar and 40% of quartz is subjected to flotation in a laboratory flotation machine. The reason for the lack of separation is a low hydrophobicity of quartz in the presence of polyethylene glycol monoalkyl ethers and high intensity of mixing in the flotation machine. The flotometric tests showed that the contact angle of quartz in monoalkyl ethers of polyethylene glycol solutions is less than about 18 degrees and depends on the structure and concentration of the ether and the pH of the system.

Jan 1, 2003

By Wei Sun, Ruolin Wang, Jianjun Wang, Xiaodong Li, Honghu Tang, Yuehua Hu, Anh V. Nguyen, Haisheng Han, Kefeng Chen, Zhao Wei

It is difficult to separate scheelite especially from fluorite with fatty acid collectors because the adsorption mechanism of these collectors occurs through chemisorption of the oleate ion onto the mineral surface. A simplified flotation process using Pb-BHA complexes was developed to replace the energy-inefficient Petrov’s process of using a fatty acid, increasing the recovery of scheelite and reducing the cost. The relationship between surface chemical properties (crystal chemistry, solubility, and Zeta potential) of minerals and flotation by using a fatty acid or Pb-BHA complexes was studied in detail to provide new insights into the selective separation mechanism. The results indicate that the scheelite surface exposes more O atoms than Ca and that they are negatively charged due to the anisometric dissolution of Ca and WO4, which provides the possibility for separation using selective interfacial reaction. The FTIR and Zeta potential results indicate that both chemical and electrostatic adsorption play an important role in the adsorption of Pb-BHA complexes on the scheelite surface. The XPS results of the atomic composition and binding energies confirmed the presence of the adsorbed Pb-BHA complexes and that O and Ca may be the active adsorption sites. Therefore, scheelite was able to be collected by forming either a Ca-O-Pbcollector or W-O-Pb-collector (BHA). However, fluorite was only able to be collected by a fatty acid collector and colloidal [H2SiO3]n -, and a high temperature was needed improve the selective desorption of the adsorbed fatty acid collector by forming Ca-[H2SiO3]n - on the fluorite surface, resulting in serious problems in industry. However, the Pb-BHA complexes significantly contribute to improving the recovery of scheelite minerals, simplifying the flotation process, and circulation of the residual reagents and water. The new process has been applied in Shizhuyuan Mine, and improved the recovery by almost 10%.

Jan 1, 2018

By Wei Qu, Yongsheng Song, Xingyu Liu, Wenjuan Li, Shuang Liu, Guiying Zhou, Bowei Chen

The Pb,Sb,Zn multi-metal sulphide ore is processed in sequence of beneficiation of jamesonite, sphalerite . Due to relative large amount of collector (xanthate), activator (CuSO4) and regulator (lime) during different flotation stage, the flotation wastewater from sphalerite beneficiation stage can’t be directly recycled to the first lead flotation stage. In this paper, the flotation wastewater from sphalerite beneficiation stage was treated by Ozone and BAC technology, results showed that when the influent concentation of COD and copper ion were 850 mg/L, 10.48mg/L respectively, the Ozone and BAC technology could effectively treat such type of water. In the treated wastewater, the COD is 60mg/L, copper ion concentration is 0.023mg/L, pH is 7.0, which satisfy the need of Pb,Sb-Zn preferential floatation separation process. After recycle of the treated wastewater to Pb,Sb floatation circuit, qualified Pb,Sb concentrate and Zn concentrate were obtained.

Jan 1, 2014

By I. I. Maximov

The paper describes the results of studies performed with a view to develop an improved technology for processing high-grade massive and cupriferous ores of the Talnakh deposit, the main valuable components being nickel, copper and PGM. The studies? main task was production of nickel concentrate with nickel content of approx. 15%, nickel recovery being as high as possible. The studies were performed on two ore samples. One sample was a mix containing high-grade massive (78%) and cupriferous (22%) ores with nickel content of 1.93% and copper content of 3.6%; the other sample was a mix of high-grade ores with nickel content of 2.25% and copper content of 3.72%. Main ore minerals were copper sulfides ? chalcopyrite and cubanite, their total content being 10.5% ~ 11%, pentlandite (5.2% ~ 6.1%) and pyrrhotite (36.7% ~ 42.9%). Influence of grinding media on pentlandite and pyrrhotite separation results, achieved through combined use of triethylenetetramine (TETA) and sodium sulfite (SS), was also investigated. It is shown, that combined application of TETA/SS in the ratio of 1:2, permits to grind products in metal mill (mild steel) with metal balls (mild steel), achieving results that are similar to those achieved by means of grinding in inert grinding media with TETA/SS ratio of 1:1. Application of the developed technology provided for production of high-grade nickel concentrate with nickel content of 14.7% ~ 15.6%, nickel recovery being 76 % ~ 77%. Earlier experiments performed on the above mentioned ore mix permitted to produce nickel concentrate with nickel content of 10%, nickel recovery being 75.9%. Consequently, nickel content was increased by 4.7% ~ 5.6%, and a higher nickel recovery was achieved. The paper also describes metallurgical results related to nickel, copper and PGM with regard to all processing products.

Jan 1, 2014

By G. Demi, G. Belardi, N. Shehu, S. Cico

The physico-chemical interaction between minerals such as olivine, chromite and serpentine and the ions most commonly present in solution, like Ca and Mg and flotation reagents such as EDTA and oleic acid was investigated. The study was conducted via release tests, electrophoretic measurements and microflotation of selected minerals coming from the Kukes deposit (Albania). The results were confirmed by means of beneficiation tests on various types of ores, from the Kukes (Kalimash), from Bulquiza area and from the Rizo deposit (Greece). It has been demonstrated that when Na-K Oleate is used as collector chromite, olivine and serpentine can be separated at pH = 2.5 and/or 5.5 employing EDTA (EthyleneDiamineTetraAcetate) on previously deslimed material. This approach ensures flotation concentrates with a Cr2O3 content about 50%, at a recovery in excess of 65%.

Jan 1, 2003

By J. Sachweh

The last few years have shown a significant increase in the demands for fine products, which means everything under 10µm. There are more and more applications requesting extremely fine ground powders leading to the development of several milling machines which are better adapted to the new products. Cost saving machinery is important for the worldwide competition. Especially the energy consumption is extremely important for any fine ground product. A worthwhile field for mechanical engineering companies is the dry milling machinery as there are not as many solutions available compared with wet milling applications. In many cases wet mil-ling is the only solution to reach the requested quality, but there are also a lot of applications which can be performed in a dry way on the premise that the right mill and classifier are available. Dry milling permits to save energy and allows to influence the particle size distribution more easily, as a classifier can be used in that case. This will significantly reduce production costs and can enable the production of new products with better properties. The Tower Mill is well-known already in the field of wet grinding. Recent research work and end user reports have shown clearly that this mill has a lot of advantages compared to a ball mill. Up to now this advantage is limited to wet grinding as only few mills have been used for dry grinding. There is no doubt about the efficiency of dry grinding, but new and improved feeding and discharg-ing systems have to be developed in order to enable the full range of its advantages. Especially the high production capacities are a challenge for mill and classifier designers. The Tower Mill with its special grinding mechanism allows to cope with very high feed rates, because machines with more than 1 MW are available. Improved grinding efficiency will decrease the circulation load through the classifier and also lead to smaller classifier sizes. Together with im-proved mills the classifier can work more efficiently because the feed material is finer. Results of a test center plant production will be shown together with a comparison between stan-dard machinery and the MaxxMill®. Preferential applications for each mill will be explained.

Jan 1, 2014

By A. Mainza, H. Hill, L. Bbosa

"The main objective of ore breakage characterization is to quantify the relationship between the energy supplied for breakage and the size of the resultant progeny. In this study, the ore breakage characteristics of drill core particles and crushed particles were compared. Single impact breakage tests were conducted on a basalt ore sample using the JK rotary breakage tester. The size-dependent model by Shi and Kojovic was used to fit the breakage data because the effect of initial particle size is accounted for in the model. It was found that crushed particles consistently gave a higher degree of brokenness than drill core particles and the differences were attributed to the internal structure of the particle. Drill core particles contain a lower crack density (paths of weakness) than crushed particles which have been pre-weakened during the crushing process. An increase in crack density is directly related to a decrease in the minimum threshold energy. Upon application of a stressing force above the stress threshold, particles with a higher crack density will fracture more easily because of a higher rate of crack propagation due the numerous paths of weakness available. It was therefore concluded that under the same conditions, drill core particles are more competent than crushed particles. INTRODUCTION Comminution devices have commonly been reported as being the largest energy consumers in mineral processing circuits (Napier-Munn, 2015). Cleary (1998) reported that the inefficiency of comminution devices is a result of less than 5% of the supplied energy being utilized for breakage, with the majority being expended as heat and noise. With steadily declining fossil fuel supplies and a looming global energy crisis, the mineral processing industry has increased its focus on energy reduction measures. Ore breakage characterization plays a critical role in the design and optimization of comminution circuits (Tavares and King, 1998). The main objective of ore breakage characterization is to empirically quantify the relationship between the energy supplied for breakage (specific input energy) and the size of the resultant progeny through laboratory particle breakage tests (Napier-Munn, 1996). Commonly used laboratory breakage devices include the Drop Weight Tester (DWT), Split Hopkinson Pressure Bar (SHPB) and more recently, the JK Rotary Breakage Tester (JKRBT). Typically, a standard single impact breakage test procedure consists of a matrix of experiments on particles in four to five narrow size fractions each tested at low, medium and high energy levels. The resultant progeny of each test is sized to obtain a particle size distribution (PSD) from which the degree of breakage, usually in the form of a t10 value (percentage of the progeny material that passes 1/10 of the feed size) can be obtained for each size fraction and energy level (Napier-Munn, 1996)."

Jan 1, 2018

By Homero Delboni, Mauricio Guimarães Bergerman

"At the regrind or secondary grinding stages of metal ores, usually the concern about the energy efficiency is extremely important. In general, the specific energy consumption at this stage is higher than in the primary stages of grinding. In addition, it has been observed a tendency of finer grinding in the new projects of metallic ores, due to the finer mineral liberation, which leads to an increasing capital and operational costs. In Brazil, during the last 10 years, regrind P80 sizes of approximately 40 to 20 ?m have been necessary in all new iron and copper plants. The use of conventional ball mills, adequate for primary grinding, can result in low energy efficiency with products below a P80 of 50 ?m. This paper presents an overview of the regrind circuits in Brazil that operate with vertical mills and the results of industrial surveys at selected vertical mill circuits. Where possible, comparison is made between the plant results and the design criteria and laboratory regrind tests used for the mill sizing."

Jan 1, 2014

By Yimin Zhu, Dezhou Wei, Haijun Liang, Zhifu Zhou

It has been fairly well established by many experiments that Thiobacillus ferrooxidans (T. ferrooxidans), also named Acidithiobacillus ferrooxidans(Kelly and Wood, 2000),can depress the floatability of pyrite. However, the mechanisms governing the process have not been known completely. In the present investigation, wettability and electrokinetic studies were carried out to examine the surface chemical changes on pyrite before and after interaction with T. ferrooxidans or its secretions. Attachment of T. ferrooxidans to pyrite was observed using a scanning electron microscope. The results of experiments showed that, under certain conditions, T. ferrooxidans and its secretions would obviously change the surface electricity of pyrite and result in the iso-electric point of pyrite shifting notably. However, the surface wettability of pyrite hardly changed and its hydrophobicity increased little after interaction with T. ferrooxidans and its secretions. Based on the results of the present investigation it can be reasoned that the depression of floatability of pyrite is due to the reduction of surface free energy, rather than the increase of surface hydrophilicity of pyrite. The decrease of surface free energy weakens the attachment of collector to pyrite; during the process bacterial protein plays the most important role and the bacterial chemotaxis strengthens the effect.

Jan 1, 2003

By Xiaoming Wang

This paper presents an arcuate magnetic separator to remove the grinding ball fragment directly from the mill discharge, which will cause wear to downstream processing equipment such as pump, hydro cyclones and pebble crusher. Furth more this type separator was applied in Wushan mine under China National Group Corporation in China. After months of operation, the equipment has been a success. It removes majority of ball fragments from mill discharge. Keywords: magnetic separator, sag mill, pebble crusher, grinding ball fragments

Sep 1, 2012

By Milind Chikhale, Ranjeev Kumar, Keshav Tyagi

Ore characterisation including mineralogy and beneficiation testwork of an ore is very important for determination of possible products and their quality. The results of such study help in ascertaining the beneficiation process route for the ore. The present study deals with ore characterisation study and beneficiation testwork on the samples of hematite iron ore with goethite impurity. The characterisation study reveals that the hematite is under alteration stage to goethite which has become an integral part of hematite. High goethite/limonite content is enhancing the loss of ignition content of the ore and reducing its Fe content. The findings indicate that in case of hematite iron ore associated with goethite and limonite, it is difficult to achieve high grade of concentrate above 65% Fe. It depends on the amount of goethite and limonite minerals and their association with hematite. These minerals contain aluminous impurities and hence, their rejection becomes essential. Separation of limonite and of goethite to limited extent is possible. In case of goethite, effective liberation is not achieved where it occurs as surface alteration product of hematite grains. The gangue mineral reported are clay and gibbsite, and are closely associated with iron minerals. The test work results indicate the grade and recovery of Fe along with alumina and silica content in lumps, sinter fines and pellet feed fines that can be achieved for the different ore types vis-a-vis the percent of available hematite in the ore. The recovery of iron is dependent on the hematite available and the loss of iron values in tailings is more because of rejection of limonite and goethite.

Jan 1, 2014

By S. V. Balikov

A close association of fine gold with pyrite and arsenopyrite is observed at many gold ore deposits. Gold forms and gold distribution in sulfides of different deposits were studied. A comprehensive method including optical spectrum analysis, X-ray diffraction analysis, high-temperature X-ray diffraction analysis, scanning electron microscopy and X-ray microanalysis was used for the de-tailed investigation of the defectiveness of the structure of pyrites from different deposits. It was shown that gold content in pyrites varied from 1.5 g/t to 100 g/t compared with 30 g/t to 230 g/t in arsenopyrites. The nature and arrangement of inner inclusions of foreign minerals in pyrites as well as occurrence of fractures and macro- and microdefects were examined. Iron, sulfur and arsenic contents in all pyrite samples were determined. Chemical composition of the detected inclusions was defined. Parameters of submicroscopic structure of pyrite were estimated using X-ray Fourier line shape analysis. Estimation of real structure characteristics with calculation of submicroscopic D-blocks and root-mean-square lattice deformation 2()evalues was performed. Defectiveness of the pyrite structure can be defined by the following parameters: K?1 and K?2 reflection resolution and its intensity within high Bragg angles; S content to Fe content ratio; the arsenic content and the local variation in its concentration within the pyrite grain; the size of submicroscopic blocks and the crystal lattice disturbance value. The performed analysis showed some relationships between these parameters and refractoriness of the pyrite concentrates. It was observed that at S/Fe ratio close to or higher than stoichiometry and at a low arsenic content (less than one per cent) pyrite concentrates were not refractory. The analysis results showed that concentrates of the Beryozovskaya gold plant (0.02~0.07 As%) and concentrates of the Kommunarovskaya gold plant (less than 0.05 As%) as well as some pyrites from the Sukhoi Log gold deposit had the same characteristics. It was found that average arsenic content did not excess 0.2 per cent. Arsenic distribution within the grain of all these pyrites was uniform. At S/Fe ratio lower than or close to stoichiometry and at high arsenic content (more than one per cent) and significant variation in its distribution within a pyrite grain the pyrite concentrates are refractory. Such pyrites are typical for the Sukhoi Log, the Bakyrchik and the Mardzhanbulak gold deposits. Direct correlation between arsenic and gold contents, in particular, in fine grains of pyrite was observed by many researches. This correlation was explained by impregnation of arsenopyrite which normally contains more gold than arsenic pyrites. The analyses results showed that no arsenopyrite impregnation was found: arsenic distribution within the grain was uniform but its concentration varied greatly. Such pyrite concentrates are more refractory. This paper presents the results of analyses of sulfides to determine the amenability of the associated gold recovery by hydro- and pyrometallurgy.

Jan 1, 2014

By Klaus M. Hahn, Kurt Aasly, Jutta Lennartz, Hermann Wotruba, Ben Snook, Przemyslaw B. Kowalczuk, Rolf Arne Kleiv

"Seafloor massive sulphide (SMS) deposits have been identified as important marine metal resources for the future. However, literature on mineral processing of SMS is currently limited, and to date, no research has been published on processing of SMS from either active or inactive hydrothermal vent fields on the Arctic Mid-Ocean Ridge. In this paper, individual SMS rock samples from the Loki’s Castle area were tested. Chalcopyrite, isocubanite and sphalerite represented the main copper and zinc bearing minerals in the SMS samples, whereas the gangue consisted of barite and silica. Based on the X-ray transmission response (XRT), i.e. differences in the atomic number of elements in tested samples, and using portable XRF (PXRF) values of elemental composition, individual particles were classified as a either product (low barium / high to low silicon / high copper and zinc) or waste (high barium / high silicon / low copper and zinc). The classification was based on the elemental composition of the samples with the cut-off grade equal to 0.5% for copper. It was shown that the XRT discrimination analysis correlated well with elemental (PXRF) data classification. The results clearly indicate that X-ray transmission sensor-based sorting can be used a useful technique for preconcentration of SMS rock samples. INTRODUCTION Due to different compositions of investigated samples, sensor-based sorting is a useful technique for preconcentration of different materials. The aim of using sensor-based sorting is to upgrade an ore by reducing the quantity of overall waste material reporting to the next processing stage. This can be achieved by eliminating (reducing) the waste fraction. By applying sensor-based sorting, the energy consumption for particle comminution as well as the required process water and reagents can be decreased. The total volume of the waste rejection leads to a proportional reduction in the total energy costs (Lessard et al., 2014, 2016)."

Jan 1, 2018

By Zhiyong Gao, Ruiying Fan

"Crushing and grinding are the prerequisite processes in many industries, such as minerals processing and powder technology. During crushing and grinding, minerals will cleave or fracture along the directions by broken the interlayer bonds (e.g., ionic bonds), generating some commonly exposed surfaces. The broken (or dangling) bonds at the generated surface makes the surface more active and determine the reactivity of the surface. In this work, the population of broken (or dangling) bonds on commonly exposed surfaces of fluorite mineral (a chosen model mineral) was calculated. Based on the calculated broken bonds information, the anisotropic surface reactivity of fluorite such as surface energy, surface relaxation, dissolution, wettability, surface charge and adsorbability, were discussed. The results show that the surface broken bonds density, which is positively related to the surface energy, can be used to predict the cleavage nature, surface relaxation degree and surface stability of fluorite crystal. The distribution characteristic and the number of broken (or unsaturated) bonds of surface active atoms (like Ca for fluorite crystal) can be used to predict and explain the anisotropic wettability, surface charge and adsorption mode and strength of organic molecules on different commonly exposed surfaces. It is easy to conclude that the calculation of surface broken bonds can serve as a fast and accurate way to start the mineral chemistry studies. These findings will be helpful to the mineral/material chemistry research in related interfacial science communities.INTRODUCTIONGrinding for mineral liberation is a prerequisite for a successful flotation separation. Also grinding for size reduction is a prior process for a favorable powder technology. During the grinding process, the minerals / materials will cleave and fracture along certain crystal directions with relatively weak interlayer chemical bonds1 to form a number of common exposed surfaces. Exposed surfaces are the outer boundary of a solid substance. In the mineral / material block, the bonding orbital of the atoms is filled with electrons and the atoms are in a steady state. Atoms on these exposed surfaces appear to show dangling bonds (or broken bonds) by losing chemical bonds to adjacent atoms in the previous block. Therefore, surface broken bonds serves as an initial property of a fresh surface. The lattice arrangement and crystal orientations causes differences in the number of dangling bonds on each exposed surface, i.e., anisotropic surface broken bonds2. The anisotropic dangling bonds enable the exposed surfaces to show varying degrees of surface reactivity (including surface energy, surface charge, surface relaxation, dissolution, wettability and adsorption behavior), known as anisotropic surface reactivity."

Jan 1, 2018

By Andrzej Wieniewski, Cezary Regula, Bozena Skorupska, Krystian Cichy

"In this paper, experiences from Polish non-ferrous metals ores enrichment plants in the copper and blende concentrates quality improvement are discussed. The blende concentrate being produced in ZGH Boleslaw S.A., with Zn content of about 54,5% is characterized by the relatively high magnesium content reaching a level of 1% resulting from the dolomite presence, while for the zinc production by electrowinning a concentrate in which magnesium content should not exceed 0,3% is required. The implemented new technology for the quality improvement of blende concentrate is based on the leaching of zinc concentrate with sulfuric acid aimed at dissolving of the contained dolomite, and then flotation of the leached concentrate. It allows to obtain a concentrate with magnesium content below 0,1% at the simultaneously increased zinc content to about 57,5%. In the paper, laboratory tests results on the development of optimal flotation flowsheet for the gypsum removal and the industrial tests results concerning the process optimization of this flotation are discussed. In turn, the copper concentrate being produced in Polish copper ore enrichment plants KGHM PM S.A., is characterized by the increased organic carbon content - above 8%. It creates problems with the smelting of this concentrate because of difficulties with the heat removal derived from the combustion of organic carbon in the flash smelting process. The implementation of segregating flotation to the industrial practice allows the effective production of two concentrates with the differentiated chemical compositions - a concentrate with increased copper content and reduced organic carbon content for the flash smelting process, and a concentrate with lower copper content and increased organic carbon content for the shaft smelting process. In the paper, conditions of the segregating flotation and the achieved results are described."

Jan 1, 2014

By Irena Grigorova, Tashka Ignatova, Ivan Nishkov, Andrian Valchev

"Feldspars used by ceramic and glass industries as fluxing agents are mainly obtained from high quality feldspar deposits. The demand for feldspar as raw material for industrial applications especially in ceramic manufactures is continuously increasing. However, due to the depletion of those deposits, the research activities related to the recovery of feldspar from the lower grade feldspar deposits and feldspar bearing rocks such as pegmatite, granite, arkosic sandstone and syenite have been intensified in the last two decade. In Bulgaria, the main deposit of arkosic sandstone is located in the area of Shumen town, NE Bulgaria. In Srednya deposit arkosic sandstones are found in Upper Cretaceous sediments (Santonian). In this formation, there are two major industrial minerals - feldspar and quartz. They may be of economic value and possibly suitable for commercial uses. The main purpose of the present study was to investigate the beneficiation and upgrading processes of Srednya deposit arkosic sandstones. In a laboratory scale it was studied the possibility to obtain the feldspar concentrate and quartz sand from arkosic sandstones. Particle size distribution, chemical and mineralogical compositions of quartz-feldspar sands were determined. The bench-scale tests using the KOALIN AD laboratory experimental facilities were conducted. Many processing techniques were tested: disintegration, washing, sizing, carbonate flotation and feldspar flotation. The experimental results show that there are possibilities to obtain the silica sand with low content of Fe2O3 - below 0.02 % and potassium feldspar with content of K2O > 14 %. A new technology for recovery of feldspar and silica sand from arkosic sandstone was developed."

Jan 1, 2014

By Mohammad Noaparast, Hamed Haghi

"In this research work, it was attempted to reduce the iron contents (Fe2O3) in relatively low grade silica sample which was obtained from Shenin silica mine, using magnetic separation. The prepared sample contained 93.75%SiO2, 0.44%Fe2O3, 2.78%Al2O3, and 0.08%TiO2 and the Fe2O3 had to be reduced to less than 0.08%. Mineralogical studies and XRD analysis indicated the presence of Hematite, Pyrite, and Goethite as the major iron impurity phases. Mineralogical studies of polished and thin sections demonstrated that the degree of freedom of silica is more than 80% in -300+212 ?m size fraction. After primary stages including crushing, milling, scrubbing and de-sliming, various methods such as low intensity magnetic separation (LIMS), high gradient magnetic separation (WHGMS) and dry high intensity magnetic separation (DHIMS) were applied to find out that which process would be appropriate for the elimination of iron impurities from this sample. Different experiments were carried out on the product of wet rod mill and scrubber. However the magnetic field intensity of WHGMS was increased down to 2Tesla, and there was not any acceptable result in reduction of Fe2O3 content lower than 0.08%. Thereafter the product of wet rod mill and scrubber were dried and reported to DHIMS. In these experiments, maximum magnetic field intensity was 1.4Tesla. In this case very significant results were achieved, and Fe2O3 content of final product were reduced to less than 0.05% which meets glass manufacturing standards."

Jan 1, 2014

By Bruce Mathema, Steven Huynh, Terry Cheng, Gerry Gomez

"The use of PM40N, a specialty precious metals promoter in conjunction with a standard Xanthate based collector was extensively investigated in the flotation of a complex, silver-bearing, lead-zinc ore containing naturally occurring graphitic gangue. The ore, considered difficult to treat with conventional reagents, was tested at plant scale to determine the impact of the promoter on silver recovery, lead grade and also on the amount of zinc misplaced to the final lead concentrate.Initial laboratory-scale rougher flotation testing implied significant improvements in the recovery of silver and lead with a marginal amount of zinc displaced. Subsequent mini pilot flotation tests further revealed that a gain in selectivity and recovery could be achieved by adjusting PM40N promoter dosage and incorporating a cleaner flotation step, further improving rejection of sphalerite. Plant trials resulted in an improvement of 3% in Silver recovery coupled with a 2% increase in recovered lead whilst maintaining lead grade in the lead circuit.To date, the use of PM40N as a promoter has enabled the processing operation to significantly increase its plant economics. The partial replacement of the standard Xanthate based collector has also reduced the overall quantity of Xanthate required in the standard circuit by approximately 10% - which is a positive impact on the environment. It is envisaged that further optimization of plant parameters will favor stable operation and continue to boost revenues generated by subsequent improvements in silver metallurgy."

Jan 1, 2014

By Chenyang Zhang, Zhigang Yin, Jianyong He, Yuehua Hu

"A lot of floatation reagents (collectors, inhibitors and regulators) for the beneficiation of copper ores have been well developed in the past century. However, it is still unclear about the micro interaction mechanism of these flotation reagents with copper ores. In this paper, the interaction mechanism of these flotation reagents with the copper atom on chalcopyrite has been systematically investigated by first principle DFT (density functional theory) calculations. Thirty-four specific common functional groups linked with the same hydrocarbon chain (ethyl) are optimized at a B3LYP/def2-TZVP level, the solvation effect was included with the SMD solvation model. The analysis of the highest occupied molecular orbital (HOMO), the lowest unoccupied molecular orbital (LUMO) and nature bond orbital (NBO) charge of these reagents reveals their potential applications to other types of copper-bearing mineral. Further investigation of the thermodynamics calculations gives more reliable data to screen collectors or inhibitors for copper-bearing mineral. The flotation results from carefully reviewed literatures are in good agreement with the calculation results. This work might also shed new light on the development and discovery of highly efficient and selective flotation reagents with low cost based on the computational methods.INTRODUCTION Froth flotation,(Shean & Cilliers, 2011) a mineral processing approach, is applied to efficiently enrich valuable minerals from the mixture, which is achieved according to the dictinctive surface properties of minerals. In the past century, researchers have develped an aboundant of flotation reagents by extraction or synthetize, and many carefully selected reagents might die in the bench tests or the pilot tests before the pratice.(Bulatovic & SrdjanM, 2007) Generally, it involves a lot of cost and tedious works by conducting flotation tests to screen flotation reagents. Flotation reagents have been boomed robustly with the developing of the organic synthesis.(Liu, Yang, & Zhong, 2017) Reseachers found the specific properties of a reagent are determined by its functional groups and the length of the hydrocarbon, where the functional group is assigned as the adsorption site to adsorb onto mineral surfaces and the hydrocarbon chain is called as a hydrophobic group."

Jan 1, 2018

By A. Javadi

"Our recent studies revealed that the sulfide minerals in contact with water during grinding produced hydrogen peroxide (H2O2) where the amount of H2O2 production by the minerals found to be in the order of pyrite > chalcopyrite > sphalerite > galena. The H2O2 effect on the oxidation of pulp components and its influence on the concentrate grade and recovery in flotation have been studied and the results have been presented and discussed in this paper. Studies have also been carried out to build correlation between percentage of pyrite in the concentrate, grinding conditions and concentration of OH•/H2O2 in the pulp and as well of controlling the formation of these species through known chemical means for depressing the generation of the oxidant. Flotation tests using a complex sulfide ore with the same reagent scheme that is being used at Bama concentrator in Iran but with the addition i) Na2S reductant and ii) inorganic (EDTA) and organic (TETA) surface modifiers, during grinding stage have been performed to judge the beneficial or detrimental role of H2O2 on the selective flotation of sulfides. The results demonstrate that the selectivity of metal sulfides against pyrite increases with increasing generation of H2O2 in the pulp liquid.INTRODUCTIONOur recent studies have illustrated the formation of hydrogen peroxide (H2O2) by metal-sulphides during grinding in the presence and absence of oxygen (Javadi Nooshabadi & Hanumantha Rao, 2013a; Javadi Nooshabadi & Hanumantha Rao, 2013b; Javadi Nooshabadi & Hanumantha Rao, 2013c; Javadi Nooshabadi & Hanumantha Rao, 2014). In the absence of oxygen, it was found that pyrite surface is catalytically active and able to breakdown water molecules to form OH• free radical and thereby deriving oxygen in the formation of H2O2 from water molecules. The in-situ formation of H2O2 and its influence on sulphide flotation has not been addressed yet. The presence of strong H2O2 oxidant in the pulp liquid and its selective oxidation of pyrite would be beneficial in depressing pyrite flotation. Therefore, it is important to build correlation between percentage of pyrite in the concentrate, grinding conditions and concentration of OH•/H2O2 in the pulp as well as to study possible ways of flexibly controlling the formation of these species through known chemical means for depressing the generation of the oxidant."

Jan 1, 2018