Search Documents

By Timothy C. Siegel

Given that piles are composed of different materials and installed using a variety of methods, ASTM D 1143/D 1143M-07 Standard Test Methods for Deep Foundations Under Static Axial Compression is justifiably general so that it has as many applications as reasonably possible. There are aspects of the test setup, the test procedures, and data interpretation for instrumented piles (some of which are specific to augered cast-in-place piles) that are either not discussed in detail in this ASTM standard or are not addressed at all. Specifically, the use of variable time hold times can obscure the shape of the conventional load-deflection curve, as well as, influence the interpretation of the ultimate pile capacity. Unload-reload cycles induce additional non-uniform internal axial loads within the pile which complicate interpretation of the strain gage data and increase the potential for errors. Attempts to maintain a constant top load during the hold period can lead to operational difficulties in taking measurements and are technically unnecessary. Residual load has been shown to develop in cast-in-place piles and can significantly influence the axial load distribution as interpreted from strain gage data. The stiffness of cast-in-place piles has been observed to vary with the measured strain, and a constant modulus, as provided by correlation with the unconfined compressive strength of the grout, may lead to a significantly different interpretation of the axial load distribution.

Jan 1, 2010

By P. V. Chandramohan

"The paper deals with the arrangement of structural members for a retaining structure used as a berth in the port of Krishnapatnam. The height of retention is 24.3m. A T-shaped diaphragm wall acts as the retaining surface. A relieving platform has been provided at the top to ease lateral earth pressure on the wall. The diaphragm wall is tied back to a combination of vertical and raker pile. Later, this arrangement was altered to replace the relieving platform with just lowering of ground level below the berth. The tie back was changed to a classical A-frame anchorage. At certain reaches, installation of piles pointing towards the rear was obstructed by a conveyor structure. The anchorage was then changed to include a vertical pile and a pile that points towards the front of the berth. Change in position of inclined pile alters the force in the pile from compression to tension.GeneralPort is a major link in the multimodal transport chain. Berth is the heart of the Port infrastructure. It is here the ocean freight changes to land transport. The change-over, warrants special type of heavy duty handling equipment. The equipment and the process necessitate deep seated foundations. On one side of the berth, deep drafted ships would be berthed. But adjacent to this heavy duty cranes would be operating at the deck level. Berths are of various types. Some are founded on piles and may project into water. Some operators prefer a retaining structure. At the port of Krishnapatnam, a retaining structure was preferred. Dredged level at the berth was to be -20. Deck of the berth was at +4.3. This meant that the height of retention of soil was 24.3m. Ports are generally located near the coast. Subsoil in the port area generally consists of cohesive material of low shearing strength. The berth has to cater to imposed vertical and horizontal loads.Structural functionFor bulk cargo and containers, berth has to support the two crane tracks. These tracks will carry heavy wheel loads of the crane. Besides, the space between the tracks would be used for stacking of cargo or hatch covers. In short, the deck will be subjected to heavy surcharge. This vertical load will manifest as additional lateral force on the retaining wall. Since the height of soil to be retained is high, it is a practice to relieve the lateral earth pressure due to the heavy surcharge of the wall. This is done by providing a relieving platform. The surcharge of superimposed load on the deck and the self-weight of the soil up to a few metres below would be relieved by a suitable platform. This vertical load would be transferred directly to deeper levels through piles. Mooring pull is a horizontal force exerted by the vessel on the bollards towards water side. Berthing force is exerted by the vessel during berthing, through fenders and acts towards land side.Diaphragm walls are usually employed as the retaining face. If the height of retention is less, these walls can cantilever out but in the case of large retention, they have to be tied back. The ties are to be anchored on to suitable arrangements like a dead-man or an A-frame. Berthing structure in the early stages at Krishnapatnam port is shown in fig 1."

Jan 1, 2015

By J. Nakayama

For installation of round steel piles or cast-in-place pile construction through boulder contained ground or rocky formation, usual system does not function properly or impossible to work. This paper introduces an installation system which combines unique mechanism where the drill is installed on the top of a driving round steel pile or a stand pipe which is initially driven into the overburden to the depth of self-standing. When the pile driving or bore hole drilling encounters hard strata or boulder contained ground, hard material shall be crushed by the down-the-hole chiselling operated in adjustable short stroke and high frequency of blows while cuttings are discharged in reverse circulation through central reverse pipe while round steel pile is simultaneously stroked by a hydraulic hammer. The paper shall explain the mechanism of the system and introduces construction examples for bridge foundation and piled jetty.

Jan 1, 1999

By Chu E. Ho

Field load tests on deep slurry stabilized bored piles have shown that end bearing resistance was unreliable due to soft toe conditions caused by debris accumulation at the bottom of the hole during pile installation. This is true whether bentonite or polymer slurry was used. Skin friction resistance was less affected by the slurry and is more reliable. A design strategy is proposed which ensures that an adequate factor of safety against the ultimate shaft resistance is maintained for any chosen design working load, such that a pile settlement of 12mm would not be exceeded.

Jan 1, 2002

By Vincent Joannes, Marine Lasne, Luca Brenelli, Colin Serridge, Inge van Baardwijk, Martin Stanley, Anthony Fisher, Mary Ellen Bruce, Tony Suckling, Pedro Avellanosa

"Abstract The European Federation of Foundation Contractors (EFFC) and Deep Foundations Institute (DFI) developed a sector-specific carbon accounting methodology and associated “carbon calculator” for foundations and geotechnical works. The EFFC-DFI Carbon Calculator is believed to be one of the construction industry’s first collaboratively produced carbon calculator tools for European and international countries based on verifiable and standardized data. It is intended that the tool be adopted internationally and become the open-source industry standard for ground works. A detailed methodological guide is provided with the calculator (Lemaignan and Wilmotte, 2013). This guide explains the background of the standards, accounting methodologies, emission sources and factors that were used as the bases for the tool development and includes detailed guidance on use of the calculator.Drivers for DevelopmentFoundation contractors anticipate project cost and carbon emissions will become inextricably linked in response to the climbing price of fossil fuels and carbon intensive materials as resources become scarce. Low carbon solutions will therefore become more competitive options. Also with high profile construction projects having low carbon/carbon neutrality as requirements, sustainability in the foundations industry also becomes a market issue.This carbon calculator will be used to lead the industry and shape the expectations of commissioning organisations by providing insight into the carbon cost of their projects. Commissioning organizations are encouraged to be aware of the carbon impact of projects and to also facilitate a fair and accurate way of comparing footprints to provide a level playing field for foundation contractors."

Jan 1, 2014

By Richard Berry

The spacing of grout injections is typically about 2 to 2 V½ meters if the purpose of the grouting is densification of the in-situ soils. Hole spacing will vary with the in-situ soil properties and the grout injection rate; faster rates requiring closer hole spacing.

Feb 10, 2003

By Z. Q. Zhou

It is the first worke in design of pile foundation to determine the carring capacity of single pile, and a static loading on site is considered to be the lost derect and reliable way. All values P and settlements S induced can be plotted as a broken-line. Since soil is a kind of elasto-plastic and cohesive material, the increasing of settlements is generally greater than that of loads. Different value Pu nay be given by different tester on his P-S diagram, because of erroys in the test and complicated, characteristics of soil. The analytical method of exponential equation shown in this paper derives a specified solution. After using an exponential curve to regress values of loads P and corresponding settlements S from on-site test, coeficients A and B of exponential equation can be obtained. With this curve an ultimate carrying capacity of single pile can be determined. The resistant forces of pile shaft and pile tip can also be defined by the tangent of the calculated knee point, as it is called (tangent method). At last, an example is given to show how the ultimate carrying capacity of f 500mm bored pile is obtained with this method for a project in Kunming.

Jan 1, 2010

Jan 1, 1987

By Donald J. Murphy

Longevity of structural units, as compared to the planned useful life of a facility, always is a design consideration. Typical concerns include slow decay due to environmental factors, and changes in constitutive relationships governing the performance of the material involved. With respect to foundations, the usual items of interest are corrosion of steel and concrete, and time dependent behavior of the soil/structure system. For piles, as with other foundations, deterioration is precluded, mitigated or otherwise accounted for by assessing properly the ambient situation (sulphates, pH, stray currents, resistivity) and providing safeguards, such as resistant construction products, oversizing, coatings, and/or cathodic protection. On the other hand, long term performance of the pile foundations, as affected by time dependent characteristics of the supporting soil or rock, can be predicted and controlled only with a synergetic coupling of analyses and field tests. The history of a project for which this approach was followed forms the basis for this paper.

Jan 1, 1986

By Sam X. Yao

The underwater concrete technology has historically evolved largely through a trial-and-error process of constructing marine works. Many outstanding examples exist of high quality concrete placed underwater. However, failures also occurred and led to excessive cost and/or schedule overruns. These failures were largely due to improper concrete mix design or improper placement. The problems may have occurred because proper underwater concrete construction techniques and experience have not been widely disseminated. This section focuses on technical issues of underwater concrete mix design, concrete production and placement, and quality control.

Jan 1, 2013

By Filippo Leoni, Wesley Schmutzler

"The LPV-111 East Back Levee Improvement Project lies along the Gulf Intracoastal Waterway (GIWW) in Orleans Parish of New Orleans, La., and is an essential component of the New Orleans Hurricane Protection System. The Hurricane Protection Office of the U.S. Army Corps of Engineers (USACE) attributed failure of the New Orleans East levees system to overtopping, erosion and subsequent breaching of LPV-111 along the GIWW, as well as other sections of flood protection during Hurricane Katrina in 2005. The existing levee suffered extensive damages from Hurricane Katrina, such that the USACE elected to provide earth stabilization and to rebuild the levee sections. Due to the adverse geotechnical properties of the foundation soils, the Corps deemed ground improvement necessary to stabilize the new levee and to limit its footprint. Wet Deep Mixing Method (DMM) was selected as the most suitable technology for this task.ChallengesDesign: This reach specifically protects East New Orleans and the Bayou Savage National Wildlife Refuge, the largest urban wildlife refuge in the U.S. and home to several threatened or endangered species of birds as well as many reptiles, amphibians and small mammals. The Corps chose DMM due to the sensitivity of the protected marshlands and because the method limits the footprint of the raised levees. The increase in the load bearing capacity of the treated soil significantly decreases the footprint necessary to attain the required height increase. This limitation required the new levee to have steep slopes, drastically increasing the surcharge on foundation soils characterized by overall poor geotechnical properties (soft clays and peats). The design also considered the increased horizontal stresses on the levees due to the extreme storm surges during a hurricane.The design of the 1.6 m diameter (5.25 ft) DMM elements called for overlapping them to form a double auger element that formed buttresses perpendicular to the levee alignment. The contractor installed the buttresses at a maximum on center spacing of 4.7 m (15.5 ft). One additional double auger DMM element was midway between consecutive buttresses at the centerline of the levee to further help prevent settlement (Figure 1)."

Jan 1, 2013

By Austin Metz, Kevin Stanton, Ramin Motamed

"A recent study calibrated Load and Resistance Factor Design (LRFD) resistance factors for local soil conditions in the Las Vegas Valley. As a part of this calibration, an extensive database of drilled shaft load tests and associated subsurface soil information were collected and compiled. This database, deemed the Nevada Department of Transportation Deep Foundation Load Test Database or NDFLTD, was designed with the presentation of load test data, the subsurface soil conditions, and the spatial distribution of the data in mind. In addition, the NDFLTD was developed in a way that allows additional data to be added as it becomes available. As such, the rules of database normalization were followed to allow for additional and different types of data to be added to the database and reports. Microsoft Access was chosen to present the data because it is easily accessible to anyone with Microsoft office software, it has a quick learning curve, and it has the ability to present a relational database. The largest obstacle faced when creating the NDFLTD was normalizing the data used in the LRFD calibration, with the goal of reaching the 5th normal form.INTRODUCTIONLRFD is based on statistical performance of engineering components, as opposed to the more traditional Allowable Strength Design (ASD), which divides the strength of a component by a safety factor. Calibration of resistance factors for LRFD requires a robust statistical analysis of past performance. For drilled shafts this requires a database of full scale load tests (Abu-Hejleh et al. 2014). The FHWA developed the largest US based deep foundation load test database, deemed the DFLTD, collecting data from 1985 to 2003 when funds ran out (Abu-Hejleh et al. 2014). Recently, the DFLTD has been updated to modern standards (Petek et al. 2016). In October of 2007, the FHWA mandated state department of transportations (DOTs) to follow AAHSTO LRFD guidelines for their highway foundation designs (Abu-Hejleh et al. 2014). Since then multiple state DOTs have developed their own, region specific deep foundation load test databases. Florida has a long history of developing databases for deep foundation LRFD resistance factor calibration, with the two main databases being the FL database, and The Deep Foundations Database (Abu-Hejleh et al. 2014). Iowa developed a Microsoft Access based database in 2014 (Garder et al. 2014). Oregon developed a database compiling pertinent data from the DFLTD, Florida DOT’s Deep Foundation Database, as well as from other databases (Smith et al. 2011). Illinois developed the “International Database” for static and dynamic reliability based calibration (Long et al. 2009). Louisiana developed a database for LRFD Calibration of driven piles in 2009 (Abu-Farsakh et al. 2009). The California Department of Transportation has its own internal foundation database, which is housed within the Foundation Testing Branch archive (Smith et al. 2011). In 2016, the Nevada Department of Transportation (NDOT) presented its own LRFD calibration for the Las Vegas Valley (Stanton et al. 2017), and the NDFLTD was developed as a part of that project (Motamed et al. 2016)."

Jan 1, 2017

By Xu Ronglie

This paper looks back on the developments and achievements of deep foundations, on the basis of the complex geological conditions and environments in China. It sums up advances in theoretical and applied researches, engineering constructions, practical experiences, case histories, and problems and developing prospects of piles and deep foundations in recent years in China.

Jan 1, 1991

By John J. Vieaux

Allowable loads on Dynamically-Cast-In-Place Piles (the Franki type) can be correlated with N values from the Standard Penetration Test. Using a constant developed by Nordlund, a conservative value for load-carrying capability of a DCIP pile is developed. The DCIP pile and method of installation is briefly described.

Jan 1, 1984

By Tracy Brettmann, Melis Sutman, C. Guney Olgen

"The use of energy piles for geothermal heat exchange has been steadily increasing during the last decade, yet there are still pending questions on their behavior during temperature changes. This paper focuses on the thermo-mechanical response of three full-scale energy piles installed in Richmond, TX. The behavior of test piles subjected to thermo-mechanical loadings was studied in situ with the aim of quantifying the thermal influence on the performance and capacity of energy piles. An extensive field test program, including conventional pile loading tests and application of heating-cooling cycles was conducted on the test piles during a period of six weeks. For thermal load applications, the heat exchanger fluid with maximum temperature of 113°F (45°C) and minimum of 47°F (8°C) was circulated in the geothermal loops placed at the center of the test piles. Optical fiber sensors, vibrating wire strain gages, thermistors and thermal integrity profile wires were installed to monitor the strain and temperature variations along the energy piles throughout the field tests. The strain and temperature profiles during heating-cooling cycles on the test piles under static loads and without a maintained load were monitored to investigate the effect of thermo-mechanical and pure thermal loads on the energy piles, respectively. Conventional pile load tests were applied before and after the application of thermal cycles. The results of the pile load tests are compared to evaluate the effect of temperature cycles on pile capacity.IntroductionEnergy piles are deep foundation elements designed to access and exploit the relatively constant temperature of the ground and its heat storage capacity for efficient heating and cooling of buildings. The deep foundation elements that are already in place for structural support are integrated with adsorber pipes to perform as heat exchangers connected to ground source heat pump (GSHP) systems. With the use of energy piles, the heat energy is fed into and withdrawn from the ground for cooling in the summer and heating in the winter, respectively.Energy piles present an innovative way to harvest near-surface geothermal energy and to provide lower carbon emissions, however, there are still pending question on their performance. During heating-cooling cycles, energy piles experience temperature changes, which result in expansion or contraction of the piles."

Jan 1, 2017

By S. X. Liang

In China, the bearing capacity predictions of the pile with Stress-Wave Theory have been developed rapidly in recent years. This paper recommended a DZH-3 Pile Driving Analyzer and its relevant computer programs. Taking Qinghai Hotel Project for example, it gave their applications in the dynamic tests of large diameter cast-in-place piles.

Jan 1, 2010

By Janaka J. Kumara, Takashi Kurashina, Yoshiaki Kikuchi, Takahiro Yajima

"The inner frictional resistance of open-ended piles depend heavily on the degree of soil plugging. Many factors including pile diameter, relative density and end conditions of the piles influence the degree of soil plugging. In this paper, the effects of inner sleeves attached at the pile base on the inner frictional resistance are discussed. The experiments were conducted on a medium-dense sandy ground using smallscale model piles. The results suggest that the inner frictional resistance is influenced by sleeve height for 50 mm diameter piles although it is independent for 30 mm diameter piles. The results also indicate that soil plug height is influenced by the sleeve height. The results of the incremental filling ratio (IFR) showed that penetration of non-sleeved piles is closer to unplugged state than the sleeved piles. The results of the IFR also reveal that the degree of soil plugging is affected by the sleeve height for 50 mm diameter piles although the variation is very limited in 30 mm diameter piles. The results on the coefficient of lateral earth pressure suggested that it increases from 1.08 – 1.75 when the sleeve height is increased from 10 – 100 mm for 50 mm diameter piles.INTRODUCTIONPrevious studies have shown that the behaviour of open-ended piles is different from closed-ended piles (Szechy, 1961; Randolph et al., 1979; Paikowsky and Whitman, 1990). Open-ended driven piles are widely used for deep foundations, in particular in offshore deep foundations. Generally, it is accepted that a short open-ended pile produces a smaller bearing capacity than a similar closed-ended pile (Nauroy and Tirant, 1983). However, a long open-ended pile can produce a similar bearing capacity as a closed-ended pile due to a large inner frictional resistance mobilised between the inner pile shaft and inner soil (Lehane and Randolph, 2002). The ultimate bearing capacity of an open-ended pile, Qu consists of three components as given in Eq. 1."

Jan 1, 2017

By Arash Khosravifar

The seismic design of extended pile shafts for the combined effects of dynamic shaking and liquefaction-induced lateral spreading is investigated using nonlinear dynamic finite element analyses (NDA). Results of NDA parameter studies are used to illustrate how inertia and lateral spreading loads combine during shaking. The NDA results are used to evaluate equivalent static analysis (ESA) methods. Implications for design practice are discussed.

Jan 1, 2010

By James J. Cahill

Contractor's working in an urban environment face a multitude of working conditions. There is no typical "Downtown" job site. From afar we just see the skyline, or up close a specific building. This, of course, does not give us a clue as to the site conditions the foundation contractor faced in doing his work. The open, downtown building site is still available on some projects, but they are becoming rare as our cities are becoming more developed. A typical site today might include any one or several of the following problems: A. Deep pit with no ramp access B. Multi-type known or unknown obstructions C. Height limitations D. Load restrictions E. Existing adjacent building founded on shallow foundation F. Existing foundations G. Existing tunnels, utilities or subways

Jan 1, 1991

By Rolf Katzenbach

The principle questions related to the design of deep foundations especially in soft soils are the stability and the cost optimised settlement reduction to prevent possible damages and to minimise the deformations of the adjacent infrastructure. The present develop­ments in the design of deep foundations lead to the design approach of the Combined Pile-Raft Foundation (CPRF) which offers a lot of new possibilities, e.g. the utilisation of the CPRF for horizontal loading or the use of the subsoil as a geothermal storage system.

Jan 1, 2006