Search Documents

By Mike McKevitt

We are trying to promote a concept and a change in management?s approach to the iterative process of grade control. This is important as grade control must routinely try and achieve the long term objectives set by the mine plan ??BackgroundBackground ??Factors contributing to variation from planFactors plan ??Basis of OptimisationBasis Optimisation ??Ore Block Optimisation processOre process ??Operating mine examplesOperating examples ??Chain of Mining. ??Intention is to highlight the need for repeatable and consistent materialand material-type classification to remain consistent with the Life of Mine Plan ??We can drill another hole or reWe re-optimise a plan, but once excavated, the final decision has been made ??The grade control decision is the last decision made in the resource exploitation sequence.

May 1, 2009

By Robin Perry, Claude Bazin

"Discrete transfer functions which use the grinding circuit feed tonnage to predict mass flowrates at reagent addition points in a flotation circuit were calibrated using a dynamic grinding/flotation circuit simulator. Predicted mass flow values are multiplied by reagent addition ratios to obtain actual reagent flow. The transfer functions are currently integrated into the distributed control system of Les Mines Selbaie.IntroductionThe development of adequate tools for the control of flotation processes is a continuous challenge. Since the early 1970s there have been numerous publications dealing with practical aspect of control of flotation processes. Most plants use a combination of feedback and feedforward controls to reduce the effect of the following flotation process disturbances (McKee, 1991):• changes in throughput;• changes in feed grade;• changes in particle floatability (size, liberation, surface oxidation ... ); and • deliberate changes of setpoint;Feedforward control manipulates variables such as reagent and/or air flow rate to attenuate the effect of disturbances such as changes of feed rate and mineral content. The feed forward strategy is driven by measurements of these disturbances. Feedback control is used to maintain process variables to targeted set-points of concentrate or tails grades. The feedback control action is driven by deviation from the set-point, caused by a deliberate change of set-point or disturbances.This paper proposes a method to improve feed forward control schemes by the addition of a simple model for solids transportation. The feedforward strategy considered in this paper is the ratio type, in which the manipulated variable is changed according to a predefmed ratio between this variable and the measured disturbance. A typical example is the ratio of the reagent addition to mass flow of ore.The paper reviews the state of the art in feed forward control strategy applied to flotation processes and describes the method used for predicting mass flow rates. The last section shows an application of the method in the Les Mines Selbaie flotation circuit."

Jan 1, 1994

By Bo-Hyun Kim

Outline ? Strainburst criteria and hypotheses adapted for this study. ? Influence of excavation method on rock mass properties. ? Excavation disturbance factors vs. deformation modulus, etc. ? Estimation of blasting damage zone around excavation. ? Considerations of energy on burst-prone ground. ? Literature review & closed form solution. ? Numerical simulations. ? Summary and future works.

Oct 1, 2010

By P. Hansman

"Place Dome Canada's Detour Lake Mine is a low-grade gold producer located in northeastern Ontario. Production is targeted for 2850 tonnes of ore per day. As reserves and mining areas continued to be found below and far to the west of the shaft (Fig. 1), it became necessary to review and upgrade the materials handling facilities. This paper deals with the selection, design and construction of an underground crusher and conveyor system capable of handling up to 450 tonnes per hour from the lowest existing level in the mine.BackgroundThe Detour Lake mine site is accessed via secondary Highway 652 which runs northeast out of Cochrane, Ontario. The road consists of 200 Ian of hard top followed by 100 Ian of well maintained gravel to the mine site. A 1500 m airstrip is maintained at the mine site for emergency use. Prior to 1991, the workforce was flown to and from the mine site. Crews were now bused to the site from Timmins. Remnants of a winter road exist to the southeast which at one time ended in La Sarre, Quebec. This was the route used to haul bulk items during the construction period and early production years.A town site has not been established at the site for the current operations. Instead, a rotational scheme is being utilized whereby most personnel will work seven days on site followed by seven days off site. For some employees, however, the work week is termed as a four/three schedule where they work 42 hours between Monday at 10:00 a.m. and Thursday at 4:00 p.m. with the following three days off. All surface employees and maintenance employees underground work 12-hour shifts. All underground employees work a lOV2-hour shift. Supervisors work a similar schedule as their crews, however, other staff may overlap their rotation during the week.A five-compartment shaft was sunk in 1984 from surface to the 610 m elevation. Shaft stations were established at the 120 m, 260 m, 360 m, 460 m, and 560 m levels. The cage compartment consists of a single deck, 4O-man cage in balance with a counterweight. The cage hoist is an Ingersoll-Rand 10H and is regulated to travel at 4.1 m/s. Two 9 t skips operate in balance at a travel speed of 7.1 mls. The skip hoist is a 3.05 m drum Nordberg. Both hoists are automated to function without a hoistman during normal skipping and cage service runs."

Jan 1, 1995

By Jonathan Peck, Jim Gray

"With the implementation of more advanced monitoring, control and locating systems in surface mines, there is an ever increasing need for their mine-wide integration toward achieving over-all optimization. AQUILA Mining Systems Ltd. is developing the basis for a comprehensive real-time monitoring, control and information system called the Total Mining System or TMS. This system is being designed to address both current and future needs of open pit mines toward improving productivity and minimizing costs, through better two-way information flow between each component in the operation. At a basic level, feedback from equipment and process monitoring will enable decision making to be based on quantitative, on-demand information, thus permitting proactive rather than reactive planning. Dynamic planning would be a valuable tool as market conditions fluctuate, equipment fleets age and variations in the grade, quality, geometry and hardness of the mined material all contribute to either changing production targets or levels of achievable performance. Such a capability could be implemented within the next two years.At a higher level, and within five years, autonomous operation and/or real-time supervisory control of mobile and stationary equipment in open pit mines will be achieved. A discussion is provided in regard to the development and implementation of an autonomous haultruck and blasthole drill, to demonstrate the need for such a system.This paper outlines a preliminary program for the design, development and implementation of this system, primarily in relation to high-level communications and its role in the future automation of open pit mobile equipment."

Jan 1, 1995

By R. F. Dawson, A. S. Bagnall, K. Barron

"At Smoky River Coal Limited (SRCL), economic occurrences of structurally thickened coal deposits form attractive surface mining targets. These steeply dipping, structurally complex deposits require that special attention be given to pit wall design and operational practices.Where anchor support is feasible, there is potential for reducing footwall waste requirements and/or increasing coal recovery. SRCL has used rock anchors to support footwall slopes since 1985. This paper outlines design considerations and performance of rock anchor support systems at SRCL.Three case histories are included that illustrate the design process for supporting steeply dipping footwall slopes using rock anchors.IntroductionWestern Canada contains vast reserves of high grade coking coal largely located in two belts within the Rocky Mountain Foothills straddling the Alberta/British Columbia border. There are about one billion tonnes of ""clean"" coking coal reserves (Romaniuk and Naidu, 1986) situated near existing mining infrastructure. Within the reserve areas shown in Figure I, a total of six producers operate 10 large mines linked with ports situated on Canada's west coast. Al! of the producers operate conventional shovel/truck surface pits.Surface mineable reserves within some of the mountain coal mines are located on dip slopes or where the geologic structure has thickened the coal near the surface, creating low strip ratio targets. Footwall slopes in these mines are developed parallel to bedding, thus minimizing waste extraction and preventing undercutting of potentially unstable strata. The base of the mineable coal measures in both north and south regions is marked by massive quartz sandstone units (Torrens Member and Moose Mountain Member) which often form the footwall. Footwalls developed within this basal sandstone unit can attain very high unbenched heights often with little risk of instability. In cases where the footwall is developed on weaker strata above this basal unit, stability considerations control slope height when bedding dips exceed about 30°. In these situations it is desirable to assess the benefits of artificial support to increase the unbenched footwall slope height."

Jan 1, 1995

Caterpillar Inc The world's largest manufacturer of construction and mining equipment, diesel and natural gas engines and industrial gas turbines. Technology leader in logistics, construction, transportation, mining, forestry, energy and electric power generation.

Aug 1, 2013

By John Drobe, Robert M. Cann

"Abstract - The Minas de Oro Cu-Au skarn and replacement deposits are located in the highlands of central Honduras, 90 km north-northwest of the capital of Tegucigalpa.The deposits formed in Cretaceous volcano-sedimentary rocks following the emplacement of an early Paleocene granodiorite to dacite intrusive complex. Three types of skarn (Type IA, IB, and IC) and a low-temperature replacement mineralization (Type II) are recognized. Type IA skarn consists of massive brown-green andradite and lesser magnetite and pyroxene. Type IB skarn has magnetite + hematite as the main constituent and garnet <50%. Type IC skarn comprises >50% pyrrhotite + chalcopyrite with interstitial garnet or pyroxene. Au and Cu occur in potentially economic concentrations in all skarn types while other metals such as Ag, Pb, Zn, and Mo are locally present in significant quantities. The highly variable distribution and nature of the skarn deposits is controlled by: (1) intrusive activity, (2) composition of host rocks, (3) faulting and fracturing, and (4) attitude of host carbonates.Type II Au-Cu-As mineralization occurs in calcareous sandstone and conglomerate 2 km distal from skarns and comprises clots of Cu sulfides hosted within a zone of brecciation and quartz flooding. Garnet and/or magnetite skarn is not present and the mineralizing event appears to have been a low-temperature replacement type.The similarity of coeval Au-Cu-Fe skarns in central Guerrero, southern Mexico to Minas de Oro skarns, and the similar local stratigraphy is consistent with the generally accepted theory that the Chortis block originated from southern Mexico and during the Tertiary moved southeast to its present position."

Jan 1, 2000

By Takao Oishi, Go Ohara, Toru Kitazaki, Masahiro Tanaka

"The High Pressure Acid Leach (HPAL) plant for nickel-cobalt mixed sulphide production at Coral Bay Nickel Corporation (CBNC) in the Philippines has been in operation since 2005 with a capacity of 10,000 t/year of nickel. Subsequent to the commissioning of the second plant in 2008, the production capacity increased to 22,000 t/year of nickel (Llerin et al., 2011). CBNC’s annual nickel production reached more than 24,000 tons of nickel in 2014. The concepts to achieve this capacity are the high availability and the reciprocally flexible operation of both plants. The availability depends on some factors, such as the control of impurities in the process and the equipment condition, to mention a few. In the HPAL process, it is not only the autoclave operating conditions that affect nickel extraction but also the impurities in the ore greatly influence it. The major element in the ore is iron and most of this iron is precipitated as Fe2O3, while the rest remains as Fe2+ or Fe3+ sulphate in solution. These ions in solution reduce the availability, so it is important to control the formation of iron ions by controlling the impurities in feed ore as well as the HPAL conditions. This paper presents the general HPAL process and the behaviour of impurities, focusing on iron behaviour in the HPAL process.INTRODUCTIONCoral Bay Nickel Corporation ProfileCoral Bay Nickel Corporation (CBNC) was founded on April 2002, as a joint venture of four companies; namely, Mitsui Corporation (18%), Sojitz Corporation (18%), Nickel Asia Corporation (10%) and Sumitomo Metal Mining Corporation (SMM) with a controlling stake of 54%. Aside from its capital share, Nickel Asia Corporation also supplies the ore and limestone for the High Pressure Acid Leach (HPAL) plant located in Rio Tuba, Philippines, as shown in Figure 1 (Tsuchida, 2008). The objective of the CBNC project is to produce 22,000 t/year (original design) of nickel and 1,500 t/year of cobalt, as sulphide, by the treatment of nickel laterite ore which is a low grade nickel oxide ore in the Philippines (Mines and Geosciences Bureau, 2014). The sulphide product has been exported as a raw material to the SMM Nickel Refinery in Japan for 30 years. The product of this plant, a mixed (Ni/Co) sulphide, is shipped to the SMM’s Nickel Refinery in Niihama, Japan. SMM Corporation provides the technology and management personnel to the plant. SMM Corporation also supplies the sulphuric acid, which is the main reagent for the HPAL process."

Jan 1, 2016

By R. F. Dawson, A. S. Bagnall, K. Barron

"At Smoky River Coal Limited (SRCL), economic occurrences of structurally thickened coal deposits form attractive surface mining targets. These steeply dipping, structurally complex deposits require that special attention be given to pit wall design and operational practices.Where anchor support is feasible, there is potential for reducing footwall waste requirements and/or increasing coal recovery. SRCL has used rock anchors to support footwall slopes since 1985. This paper outlines design considerations and performance of rock anchor support systems at SRCL.Three case histories are included that illustrate the design process for supporting steeply dipping footwall slopes using rock anchors.IntroductionWestern Canada contains vast reserves of high grade coking coal largely located in two belts within the Rocky Mountain Foothills straddling the Alberta/British Columbia border. There are about one billion tonnes of ""clean"" coking coal reserves (Romaniuk and Naidu, 1986) situated near existing mining infrastructure. Within the reserve areas shown in Figure I, a total of six producers operate 10 large mines linked with ports situated on Canada&apos;s west coast. Al! of the producers operate conventional shovel truck surface pits.Surface mineable reserves within some of the mountain coal mines are located on dip slopes or where the geologic structure has thickened the coal near the surface, creating low strip ratio targets. Footwall slopes in these mines are developed parallel to bedding, thus minimizing waste extraction and preventing undercutting of potentially unstable strata. The base of the mineable coal measures in both north and south regions is marked by massive quartz sandstone units (Torrens Member and Moose Mountain Member) which often form the footwall. Footwalls developed within this basal sandstone unit can attain very high unbenched heights often with little risk of instability. In cases where the footwall is developed on weaker strata above this basal unit, stability considerations control slope height when bedding dips exceed about 30°. In these situations it is desirable to assess the benefits of artificial support to increase the unbenched footwall slope height."

Jan 1, 1995

By R. Spring

"Soft-sensors are a computer software alternative to inadequate hardware instrumentation. Filters are averaging methods that reduce the noise in any sensor&apos;s signal. This paper introduces these topics and places them in a mineral processing context using then-product formula.Soft SensorsAs their name implies, ""soft-sensors"" are computer programs that estimate values for process variables (Tham, 1991). This approach is useful when the appropriate hardware sensor does not exist, is deficient, supplies only infrequent values, etc. For example, in mineral concentrators the traditional magnetic flowmeter/ nuclear density gauge instrumentation for measuring slurry flows costs $5,000 or more per flow and requires frequent maintenance. However, metal assays are commonly available from online X-ray fluorescence analyzers and application of the n-product formula (Taggart, 1945) to these assays conveniently provides software estimates of the flowrates (albeit only when the circuit is in steady-state).Soft-sensors are used by inferential controllers that base their control actions on the process values ""inferred"" by the soft-sensor. Such was the case at Brenda Mines where the rod mill feed tonnage controller used an inferred value of the cyclone overflow particle size (Bradburn, 1976). It was also the case at Brunswick Mining where reagent controllers adjusted reagent addition rates throughout the plant according to the various ore flowrates inferred by an expert system (Spring, 1991). A unique feature of the expert system soft-sensor was its dynamic flow models which compensated for residence times, material transport lags, etc. Thus the soft-sensor values were valid under both steady-state and nonsteady- state conditions."

Jan 1, 1992

By Robert B. Parsons

"The new Ontario Liberal government introduced its first budget in October. The changes to The Mining Tax Act proposed in the budget are mean t 10 simplify the current system without any loss of revenue to the government. It goes without saying that some operators will benefit from the changes while others will pay more taxes after 1985.With regard to ongoing matters at the federal level, the proposed carve-out legislation and the issue of northern allowances are being discussed with government officials, and a small victory has recently been scored with regard 10 the laxation of certain share transactions of prospectors and grubstakers. A report on these issues is provided herein.Ontario BudgetOn October 24, 1985, Ontario Finance Minister Robert F. Nixon tabled a budget proposing several significant changes to both the Ontario Mining Tax Act and the province’s income tax legislation.Mining Tax ActA flat rate of tax and reduced processing allowances highlight proposed changes to The Mining Tax Act. The proposed changes, with a comparison to the existing system, are set out in Table I.The most significant change is the replacement of the graduated tax rate schedule with a flat 20010 tax rate. This is a welcome change for most mine operators who viewed the high rate of 30% on profit over $20 million as counter-productive.However, the flat rate of ta x may not be welcome to all operators. Generally speaking, operators with less than $ 10 million annual profit are better off under the graduated rate system, while operators with annual profit exceeding $10 million will benefit from the 20010 tax rate."

Jan 1, 1986

By Robert E. McIvor

"Use of the Bond Work Index to size industrial grinding equipment was widely known. Bond also described its application for measuring grinding circuit efficiency. Bond Work Index efficiency also has been used extensively by industry, but until now without concise standard methods, or a formal guideline, for doing so. The Bond Efficiency Sub-Committee of the Industrial Comminution Efficiency work group of GMSG has produced such a guideline, which is appended hereto. It covers the methods and provides examples of how to calculate the Bond Work Index Efficiency of most industrial grinding circuits. Bond Work Index testing equipment and methods are also provided.Comminution is responsible for a major portion of mineral processing plant energy consumption and operating costs. Bond Work Index efficiency provides valuable means, first, for benchmarking one’s plant performance against others in the broad industry, and hence defining the extent of the opportunity for improvement. Secondly, improvements in circuit efficiency with implemented changes can be quantified and monitored as part of continuous improvement efforts. These two important business activities are thus facilitated, and, in the absence of any other accepted method, otherwise would be lacking without the existence and application of this standard for comparison. While often loosely applied in the past by plant metallurgical staffs, the increased precision offered by this guideline provides much clearer definition of both the conceptual and statistical meaning of these measurements. Even a small improvement can be enormously financially important, but only if differentiated by measurement. This guideline was thus intended to provide industry improved means to differentiate comminution circuit efficiencies. Carbon footprint reduction is coincidental, but nevertheless can be substantial.The next steps are: (1) to establish standard reference testing materials and one or more laboratories to serve as bases for reference testing; (2) to establish the accuracy of relative circuit Work Index Efficiency determinations; and (3), to develop and provide a public data base of industrial comminution circuit Bond Work Index Efficiencies."

Jan 1, 2016

By J. -P. Tshibangu, M. Ramos da Silva, F. Descamps, C. Schroeder, J. -C. Verbrugge

"The mechanical behaviour of rock materials is largely influenced by the stress state and pore pressure; this needs to be considered in many applications, such as petroleum engineering, tunnelling or stability of underground excavations.Conventional triaxial tests (d2 = d 3) are generally used to assess the influence of confining and pore pressure. In this work, those tests are performed on a porous rock named Sorcy limestone, along with more advanced stress paths like triaxial extension (d 2 = d 1) and purely deviatoric tests with independent pore pressure control. Those tests are combined to a true triaxial study on the dry rock in order to investigate the effect of true triaxial stresses and, hence, build three-dimensional limiting envelopes accounting for the influence of pore pressure.Three-dimensional limiting envelopes of dry Sorcy limestone are built in meridian and octahedral planes. The shape of the octahedral sections changes with the mean stress from triangular to hexagonal and then quasi circular. At even higher mean stresses, the evolution continues towards a triangle with apexes oriented in the direction of triaxial extension stress states. In meridian sections, the deviatoric stress first increases with the mean stress. The transition between this deviatoric mechanism and the cap surface occurs at different mean pressures depending on the Lode angle.Terzaghi’s effective stress is found to govern the yield and plastic behaviour of saturated Sorcy limestone. Triaxial tests show that the limiting envelope does not depend on the loading path (conventional compression and purely deviatoric stress paths). In triaxial extension, the brittle-ductile transition is observed for a higher mean pressure than in triaxial compression, as previously found for true triaxial tests on the dry rock.Finally, it is shown that upon appropriate normalisation, the dry and saturated yield envelopes come very close one to each other. This suggests that only the size of the yield envelope changes between dry and saturated state (pore pressure = 5 MPa); its shape does not seem to evolve."

Jan 1, 2015

By G. Kollberg

"IntroductionThe SALA Caravan Mill system represents a proven concept for the design and operation of mobile and semi-mobile ore dressing plants.The Caravan Mill has been developed to meet the demand for a flexible processing plant to be used for small and medium-sized orebodies or for pilot investigations of deposits directly at the mine site e •The first Caravan Mill installation was put into operation in 1970 and a number of plants have been delivered world-wide since then.The Caravan Mill system has great flexibility both in capacity, ranging from 50 to 1000 tons per day, and in process combinations. The process modules available are:• crushing by jaw and cone crushers;• pre-concentration by the Dyna Whirl Pool dense media system;• grinding by wet rod or ball mills;• separation by gravity, magnetic, flotation or leaching-CVP adsorption methods;• dewatering by lamella or conventional thickeners and vacuum filters.To form complete plants, auxiliary equipment is also available, such as:• bins, feeders and conveying systems;• power generator units;• water tank and pump for process water;• interconnecting piping and cables;• erection and service tool kits;• set of spare and wear parts.For mine sites with rainy or winter conditions, a plastic tent with air heater can be supplied to cover the ore dressing equipment. Each module is workshop assembled complete with slurry pumps, internal pipe work, electric wiring with plug-in connections, hoses, etc., all arranged for quick and simple connection between the units. Before delivery, each unit is tested in the workshop."

Jan 1, 1982

By C. B. Ndimande, C. Ntsele, M. Lisso, L. Arlow

"In the processing of UG2 platinum ore, stirred milling technologies are dominating regrind applications that require grinding the particles to P80s’ in the region of 45 µm. For this application stirred mills are 30–40% more energy efficient and require a smaller foot print compared to traditional tumbling mills. In this work a study was carried out using a batch pin mill and three scales of Stirred Media Detritors. A laboratory scale pin mill, a pilot scale Stirred Media Detritor with an installed power of 18.5 KW and two industrial scale Stirred Media Detritors in continuous operation, with an installed power of 355 KW and 1,100 KW were used. The industrial scale SMDs were in the secondary grinding section of a mill floatmill float (MF2) UG2 processing plants. The tests were focused on assessing the effect of feed rate and percent solids on power consumption and product fineness at lab scale, floatation response of the SMD product at pilot scale and on an industrial scale, the effect of feed rate on energy consumption and product fineness. The measurements obtained were feed flow rates, mill power and from the samples cut, particle size distribution of both feed and product. Specific energy was observed to increase with increasing percent solids over the 30wt% to 80wt% studied. Floatation response tests of the pilot scale SMD products show improvement in grade. Specific energy and reduction rations are observed to decrease with an increase in feed rate.INTRODUCTIONThe purpose of comminution in most mineral processing applications is to liberate the valuable minerals from gangue so that they can be recovered in subsequent separation stages. Most precious and base metal plants treat low grade fine-grained ores which require a higher degree of size reduction to yield the necessary degree of liberation (Partyka & Yan, 2007). Many authors have shown that the relationship between product size and grinding energy consumption is exponential, the finer the product from the comminution device, the higher the energy consumption (Gao & Weller 1993; Napier-Munn, Morell, Morrison & Kojovic, 1996; Jankovic, Valery & La Rosa, 2003). The suggested reason for this kind of relationship is that smaller particles have fewer flaws and higher strength than larger particles. Particles with fewer flaws and higher strength require higher energy for breakage to occur. One of the challenges most plants face is that of efficient energy utilisation in the liberation of the mineral from these complex ores. Conventional tumbling mills are not energy efficient in fine and ultra-fine grinding applications because some of the energy is spent on moving the charge and does not go directly into breakage. Stirred mills have been found to be about 30% to 40% more efficient and require a smaller foot print compared to traditional tumbling mills for regrind applications that require product size with P80s’ in the sub 45 µm regions (Radziszewski & Allen, 2013). Stirred mills are able to produce fine product because they can achieve a high number of stress events per unit time and volume compared to tumbling mills (Kwade, 1999a). To minimise energy usage without compromising product quality, the mining industry has adopted stirred milling technologies for fine and ultra-fine grinding (Radziszewski & Allen 2014; Kwade, 1999b). The south Africa platinum group metal (PGM) industry alone had over 40 stirred media mills installed by 2011 (Rule, 2011). Of that 40, 13 were in the ultra-fine grinding (UFG) application and the rest in main stream inert grinding (MIG)."

Jan 1, 2016

By D. MacGREGOR, VERA TUREK

The St. Canul and Ste. Scholastique orthoquartzite sanrjstone deposits are located within the Potsdam Formation near Montreal. The sandstone lies on Precambrian basement and is Cam/3rian to Ordovician in age. The Potsdam Formation shows two distinct stages of development. One created a deepwater facies represented by impure, limey or shaley sandstone; the other produced a shallow facies composed of grey, highpurity sandstone. The shallow-water orthoquartzitic sandstone at St. Canul is being mined and beneficiated by lndusmin Limited. The operation manufactures a wide range of silica products and supplies industrial areas of Quebec and Ontario with material for the glass, foundry, silicon carbide and ceramic industries.

Jan 1, 1984

By M. P. Rennick, D. M. Burton

Abstract -The Murray Brook massive sulfide deposit, which was the first geochemical discovery in the Bathurst camp, is one of the largest sulfide deposits in the area. The massive sulfides are hosted by quartzose metasedimentary rocks in the lower part of the Ordovician Tetagouche Group. This thick succession of sedimentary rocks is overlain conformably by felsic volcanic rocks, and is structurally overlain by mafic volcanic rocks. The massive-sulfide body is polydeformed, but primary metal zoning is still discernable and may permit future exploitation of discrete lead-zinc and copper zones. Although it was discovered in 1956, the deposit was not developed unti11989, when Murray Brook Resources commenced processing of gossan containing precious metals. Recovery of gold, silver, and mercury is accomplished by indoor vat leaching on a year-round basis.

Jan 1, 1992

By Barbara Kirby

Mining Industry HR Challenges Mining industry needs to hire approx. 100,000 workers by 2020 Attraction and retention of talent in all occupations Mobility of skilled workers between mine sites 70 percent of employers expect labour shortages over the next 5 years. Largest shortages: -physical sciences and engineering occupations -trades and ?undesignated? occupations ?Undesignated? Occupations ?Undesignated? Occupations -eg. mill operators, production / development miners and heavy equipment operators More than 20,000 workers will be needed by 2020 in the undesignated occupations and another 11,500 tradespersons Turnover rate for trades and undesignated occupations at mines is high: 8.3% compared to 5.6 % for all other occupations There is no system to recognize the skills of high-demand undesignated occupations

May 1, 2010

"The Kidd Creek concentrator is situated adjacent to Highway 101, twenty-four kilometres east of the center of the city of Timmins, Ontario. Sulphide ore, received by train from the minesite twenty-nine kilometres away, is processed at a rate of twelve thousand metric tonnes per day. Saleable concentrates of copper, zinc, lead and tin are produced.The concentrator contains secondary crushing, grinding, flotation, gravity separation and concentrate handling facilities. The total concentrator manpower complement is one hundred and sixty-four which includes supervision and operating personnel. Twenty-one shift personnel are required to operate the processes involved and they occupy fifteen different operating positions in addition to that of the supervisor. These positions include:1 Central Control Operatorl Metallurgical Leader1 Dryer Control Operatorl Crusher Leader3 Copper-Lead-Zinc Flotation Circuit Operators1 Pyrite Flotation Circuit Operator1 Tin Plant Operator2 Grinding Operators1 Concentrate Operator2 Crusher Operators1 Spare Operator1 Tailings Area Operator1 Automatic Sample System Operator1 Dryer Area Helper1 Crusher Helper1 Tin Plant Helper"

Jan 1, 1981