Search Documents

By Fritz F. Prugger

In August, 1970, during routine shaft grouting, a major water source was intersected. Water and quicksand under very high pressure entered the shaft at a rate of 65 m3 per minute. The mine and both shafts were flooded. The breach was sealed simultaneously from within the shaft and through a relief hole drilled from surface. The mine was dewatered, rehabilitated and the equipment was restored. Production resumed two years after the accident.

Jan 1, 1979

By Jean-Luc Beaudoin

"In addition to the actual energy consumed, billing is dependent on the peak load and the power factor. The lower the power factor goes, the higher will be the penalty the consumer pays. The principles of a power factor regulator, the two ways of improving the power factor and methods for calculating the capacitor values required will be described.The rate structure of the utility company is founded on three cornerstones: the energy consumed during a given period of time and two penalties imposed when the power factor is low or the power demand is high. Even though the normal consumption of a customer might be 10 kW, with a peak demand of 20 kW only once a month, the wiring and associated equipment at the input to the customer's plant will have to accommodate this peak demand. The power company has no means of forecasting these demands and cannot therefore provide the additional equipment necessary. So it exacts a penalty, and the customer must take all possible steps to avoid these peak power demands. This can be accomplished by using an automatic peak load regulator which will selectively disconnect the loads which are not essential in the operation of a plant .The principles of such a controller will be described.Principles of power factor regulatorsThe operating principles of a power factor regulator will now be described. It might be asked why the power factor of an electrical installation in a mine, or a factory, should be corrected at all, but there is a simple answer. In addition to the actual energy consumed, the billing is dependent on the peak load and the power factor. The lower the power factor goes, the higher will be the penalty the consumer pays."

Jan 1, 1982

By F. Gaul, H. R. Manouchehri, A. Mosser

"Mining is a major energy intensive industry that contributes in consuming about 7% of the total world’s energy in which almost half in comminution. The underlying trait that drives energy consumption upwards appears to be somewhat persistent due to increasing in population, demands and growth rate. High grade resources have been/being depleted; consequently, low grade, high competent and complex ores with complicated geological structure are brought into perspective. For efficient extraction of values from such resources comprehensive multistage mining and processing strategies must be taken into account. Different treatment technologies, including ore sorting, must be considered to improve resource efficiency and productivity while taking into account the reduction in energy and water consumptions and related sustainability issues.The implementation of sorting technology in mining industry has a long past and its impacts on improving the overall efficiency of both mining and milling have been proven. However, the lack of complete understanding of its potential combined with ore complexity and low capacity of sorting machines have prevented the large scale application in mining industry. The application of X-Ray transmission sorting at Mittersill Tungsten Mine in Austria is presented and discussed herein. A technoeconomic analysis of the technology has revealed a significant potential of adding value to the concentration process. The rough feasibility study has given a strong feed-back on profitability and short time payback of about 2 years for the investment. Except the economic benefits the technology has positive environmental impacts. The potential for saving energy and water is large. The rough calculations have revealed that the energy saving can be up of 840MWh/annum. Furthermore, the ongoing cooperation between Mittersill mine and the sorting manufacturer is a good example on how the development of more competitive products, and product offerings, can be made."

Jan 1, 2016

By Donald C. Craighead

"Overland conveyor systems to transport bulk materials from mines to processing plants or load-out stations have to be seriously considered as the viable alternative to truck and train haulage systems. With the ever-increasing price of diesel fuel, conveyors with their electrical drives generally prove to be the least costly when operating and maintenance expenses are analyzed for the life of the installation.IntroductionOverland conveyor systems are now considered as one of the viable alternatives which should be closely investigated when a mining company and its engineers initiate studies on methods of transporting raw materials from a mine to a processing plant or rail load-out station.This paper will generalize the overland conveyor and compare it with alternative handling systems. Each installation must be carefully studied to determine the best route, type of foundations river crossings; amount of excavation work for cut and fill, maintenance roads, etc. No two locations are the same nor are the principles of operation of an overland conveyor the same as those of a normal plant or mine belt conveyor. The proper time and effort must be put into the study of the system to evaluate the costs for comparison with other systems.The length of the overland conveyor depends on the layout of the mine and plant and the topography of the terrain between the terminals. Individual lengths may be up to 20 km, and a series of conveyors may extend 100 km or more.Advantages of Overland ConveyorsThe main advantage of overland conveyors is the low operating and maintenance costs which will be realized over its years of operation. Although truck haulage probably will permit lower capital investment during the initial phases of the mine development when the annual capacities have not developed to the design level, their operating and maintenance costs will be considerably higher. When evaluating the total costs per ton of material to be handled during the expected life of the operation and the projected increases for diesel fuel versus electricity, overland conveyor systems will generally prove to be economically more viable."

Jan 1, 1982

By O. E. Humeniuk, A. I. A. Salama, M. W. Mikhail

"Performance testing of prepartion plants is referred to as plant audit. It evaluates plant performance under normal operating conditions and is aimed at improving yield through knowledge of actual process performance and interactions between different processes in a plant.This paper describes the program to evaluate the performance of several Canadian preparation plants. The performance test requires the planning of a sampling campaign that would include all circuits in the plant. Samples are analyzed to determine washing characteristics (screen and float-sink), ash and per cent solids of feed and products of separation units in the plant. Performance characteristics are established based on analysis and material balance. Specific recommendations can then be made to improve recovery, and identify and explain potential causes of apparent deficiencies.The objectives of the program are to reduce the cost of production by improving recovery of clean coal and, in tum, to reduce disposed tailings, establish baseline information on coal preparation plants performance in Canada, and define R&D work needed to optimize plant operation."

Jan 1, 1993

By D. W. Euler, B. J. Clauzier

"Implementation of an effective energy management system will reduce energy costs without impacting negatively on production.The energy management system must be designed to complement the operation and be integrated with the organization. It must be reliable and easy to use but most important, it must have an accurate and timely feedback reporting system to allow the operation to take appropriate action.Falconbridge Limited was one of the first three companies to be awarded the energy monitoring demonstration program in May 1987. The program is sponsored jointly by the Ontario Ministry of Energy and Ontario Hydro.This paper describes the approach taken by Falconbridge Limited to implement the Onaping Area Energy Management System.IntroductionThe objective of the project was to implement an effective energy management system, capable of reducing energy costs without impacting negatively on production.Energy management systems must be designed to complement the operation and to be integrated with the organization. The system must be reliable and easy to use, but most importantly, it must have an accurate and timely feedback reporting system to allow the operation to take appropriate action."

Jan 1, 1990

By J. G. Whellock, R. J. Phillips, J. W. Matousek, P. J. Marcantonio

"Stillwater Mining Company (SMC), a partnership of Chevron Resources and Manville Corporation, produces a copper-nickel, platinum-palladium flotation concentrate at its Nye, Montana mine. The concentrate is then toll processed in Europe. Recognizing the economic advantage of treating the concentrates at the mine site and of retaining this strategic resource in the United States, the Company commissioned Tolltreck International Limited and International Process Research Corporation to conduct pilot scale smelting tests with a flowsheet that would maximize metal recoveries while satisfying the environmental requirements of operations at Stillwater.Primary smelting was conducted in a single phase, 50 k W, submerged-arc, electric furnace. Refining the product mattes to copper-nickel ""white-metal""; containing approximately 2% iron, was accomplished in a Tolltreck, IV-litre, top blown rotary converter. Over-all platinum and palladium recoveries were approximately 99%; copper and nickel recoveries averaged 94%. INTRODUCTION(l-4)Stillwater Mining Company (SMC) a partnership of Chevron Resources and Manville, operates a copper-nickel, platinum palladium mine and concentrator at Nye, Montana, located in the valley of the Stillwater River, approximately, 100 km southwest of Billings. It is North America's only primary producer of these precious metals. The Stillwater area was mined for chrome ore during World War U and the Korean War, but it was not until 1961 that attention was drawn to the similarities between the Stillwater Complex and the Bushveld Complex of South Africa with its deposits of platinum group metals.A concentrated search for platinum was begun by Manville Corporation in 1967. Its presence, together with palladium, in mineable quantities was confirmed in the period 1976-1978, and the first partnership to develop the deposits was formed by Manville and Chevron in 1979. Anaconda joined the group in 1983, and in 1985 its share was purchased by Lac Minerals. In 1988 the interests of Lac Minerals were purchased by Chevron and Manville.The decision to develop the mine and build a concentrator was made in 1986. Construction began in the fall of that year, and the first concentrate was produced six months later, in March 1987. Underground mining is done in a two-shift, five day- week operation. Since startup, the concentrator has operated on a 24 hour/day, 7 day/week schedule, treating an average of 635 tonnes of ore per day and producing approximately 10 tonnes of concentrate."

Jan 1, 1989

By Gerhard Melcher, Hermann Hilbrans, Michael Gamroth

"IntroductionSeveral new smelting processes have been proposed and developed during the last 20 years. This has been true, in particular, for copper smelting technology. The important impulses for the advances in this field have been the recent demands regarding the environmental protection, energy saving and improved utilization of the metals contents of deposits, in particular that of complex raw materials.The methods developed more recently for pursuing these objectives have been outlined in several papers. In some of them the advantages and drawbacks of certain developments have been stressed. These documents are of great importance for assessing the different processes. The following paper tries to explain some details of the cyclone smelting process taking into consideration a few of these well-known presentations. The effectiveness of operation of the cyclone smelting process indicates that this process presents a significant achievement when compared with other conventional methods.The application of the CONTOP smelting cyclone range s beyond the field of copper metallurgy or the smelting of sulphide concentrates with the aid of oxygen. The research work carried out in the pilot plant of KHD Humboldt Wedag AG in Cologne-Porz also includes the recovery of the metal contents of intermediate products and processing of smelter residues which have to be converted in a disposable stat e, free of environmental pollution. This paper explains a few examples in this regard."

Jan 1, 1987

By Robert B. Parsons

"Next month will mark the anniversary of the release of an important federal study on a mineral policy for Canada. The study, entitled ""Mineral Policy-A Discussion Paper"", provides well-researched coverage of a broad range of issues that are of interest to the mining industry. Unfortunately, there is a real possibility that the discussion paper will wither and die on the vine, unless the federal and provincial governments, and the private sector, collectively ensure that some of the key considerations which are raised by the paper are acted upon.IntroductionAlmost one year ago, on March 8, 1982, Federal Mines Minister July Erola released an important study entitled ""Mineral Policy-A Discussion Paper"". The discussion paper, which presents the government's assessment of the opportunities and constraints facing the Canadian mineral industry in the 1980s, was prepared within the context o f three principal objectives-strengthening the resource base on which the industry rests, ensuring the adequacy of research activities needed to support development of the resource, and furthering the development of markets for the resource It is clear that, in today's economic climate, not even the most generous incentives would turn the industry around: what is needed is a sound base for future development, when this is possible. In this regard, the discussion paper is an excellent stepping stone, in that it reviews a wide range o f fundamental policy issues which touch on all facets o f the mining industry."

Jan 1, 1983

By F. W. Wellmer

"This paper discusses the changing nature of reserve/consumption ratios, using data from Canadian operations and focussing particularly on copper.IntroductionStudies in world metal consumption and world metal reserves are done regularly by the U.S. Bureau of Mines, the German Federal Institute of Geosciences and Raw Materials, and other institutions. Formerly, on the basis of these data, the following figures were calculated:• a static lifetime of reserves-reserves at year end divided by the consumption of the previous year;• a semidynamic lifetime of reserves-reserves at year assumed constant growth rate.These figures were severely criticized because they were purely theoretical and did not consider the availability of the raw materials.Recent practice is to calculate reserve/consumption ratios (R/C ratios) for periods(1) or for different years(2,3) and to interpret the trend. For base metals, these R/C ratios are increasing (Table 1). This had led to the conclusion that today the relative availability of base metal reserves has increased as compared to 10 or 15 years ago(4,5) As there are normally numerous deposits for each commodity, the anticipated production rates of deposits are irrelevant to this conclusion as long as the statistical distribution of possible production rates does not change significantly.The above conclusion is only justified if the quality and the nature of the data base remain the same. This is certainly the case for the consumption data. It is also assumed for the quality of the reserve figures, which usually take into account only proven and probable reserves. For the nature of the reserve figures, however, this does not seem to be true.Undoubtedly, the reserves increased in absolute terms between 1966 and 1978. To put the absolute reserve figures into perspective, it is common, as said above, to compare them with the mine production, which increased in the free world between 1966 and 1978; e.g. for copper by 40%, for Pb by 17% and for zinc by 36%. However, the reserves are also influenced by other factors, such as average size of the mines, changes in the grade of the mined ore, price-to-cost relationships and the like.The purpose of this paper is to examine the nature of the reserve figures in more detail. Because the completeness of mining data published in Canada is rather exceptional, Canadian .data serve as an example and it is assumed that the conclusions can be extrapolated to other mining countries or at least to those with free market systems."

Jan 1, 1981

By P. Mayer

"Determining the correct mechanism of a boiler tube failure is important for the prevention of future tube failures. Proper corrective measures can be undertaken to alleviate the root cause or causes for a failure only when the correct mechanism is known. A mechanism of boiler tube failure is defined as the process which degrades the tube and produces a failure.An expert system package was developed for use by electric utility power plant personnel during investigation into the cause of a boiler tube failure. It is intended to assist their efforts to recognize and identify a basic failure mechanism that can produce the type of boiler tube failure under investigation. The program guides the user to the most likely failure mechanism by asking simple questions, answers which can be obtained by determining the failure location, type of fuel, and from visual inspection of the failed tube. Expert systems are a form of artificial intelligence which imitate the decision-making process of experts.IntroductionBoiler tube failures (BTFs) continue to be the single largest source of forced outages in fossil fired electricity generating stations. Because of this a concentrated effort is being made to minimize boiler tube failure occurrences. Eliminating boiler tube failures could be worth $5 billion a year to the electric power industry(1).The aggressive service environment of fossil-fired boilers is largely the reason for these failures because the combined effects of stress, temperature, corrosion, erosion and vibration cause deterioration of boiler tube material properties and reduction in wall thickness.Determination of the boiler tube failure mechanism is important for the prevention of future problems. The root cause for a failure can be established and proper ameliorative measures taken only when the failure mechanism is identified correctly. The correct identification of failure mechanism is a complex process which may include many individuals and institutions. Technical specialists in metallurgy, chemistry, combustion, and boiler design frequently cooperate with the station staff in a failure investigation . These individuals rely on personal experience and numerous reports , theories, studies, private communications and investigations concerning the different failure modes and mechanisms."

Jan 1, 1990

By J. P. Aiello

"INTRODUCTIONWhile this paper deals specifically with potential coal use at the Cold Lake Project of Esso Resources Canada Limited, a majority of the technical aspects of coal conversion could apply to any oil field and industrial boilers or stearn generators. In 1962, Imperial Oil Limited's production arm (the forerunner of Esso Resources), began examining methods of extracting bitumen from a 50 m thick layer of oil sand buried 450 m below the surface in the Cold Lake area. Almost two decades of research followed to develop an in situ oil sands recovery technology that made commercial production feasible.A $13 billion mega project that would have produced 22 000 m3/d (141 000 barrels/day) of synthetic crude oil (160 000 bpd of bitumen) was shelved in 1981, and ultimately replaced by a phased development strategy, involving smaller production units, to bring blended bitumen production on stream as markets and prices permit.The first two phases came into production in 1985. There are currently a total of six phases in production with four more in the construction stage. Each phase has 130to 140production wells (initially) and a central plant with water treatment, crude treatment and stearn generating facilities capable of producing 150 m3/d (9500 bpd of raw bitumen). The stearn generation section for each phase consists of three 180millionBtulhour oil fieldsteam generators.In its natural state, the bitumen is too thick to be recovered using conventional oil recovery techniques. At the Cold Lake Project, bitumen is recovered by a method called cyclic stearn stimulation. Water is pumped to the central plant where it is treated and heated to produce high pressure, high temperature steam. During the steam cycle, this steam is transported in insulated pipelines to the wells for injection into the oil sand formation. This cycle lasts from 30 to 50 days, heating the formation and causing the bitumen to flow. Following an initial flowback period, a surface based artificial lift system pumps the heated liquid bitumen, mixed with water and gas, out of the well and back to the central plant. The water and gas are separated from the bitumen, with the gas being used to provide some of the fuel for the stearn generators and the water being treated and recycled. Approximately 5% of the water cannot be recycled and is disposed of by injection into deep formations . The bitumen is blended with a diluent and shipped by pipeline to market."

Jan 1, 1989

By M. Walmsley, D. Maynard

"This paper describes the use of terrain and soil information in the planning of mine developments, particularly in satisfying many of the existing provincial regulatory requirements. It is also noted that, if properly used, this will provide a solid data base for cost-efficient and environmentally acceptable land use.IntroductionIn planning the development or expansion of a new or existing mine, engineering alternatives are judged on many factors, one of which is the environmental influence. Ecological investigations, ensuring consideration of a rational approach to managing land use and environmental impacts, should be carried out prior to a final decision being made on mine development. The Pit Slope Manual (CANMET, 1976) suggests that both baseline aquatic and terrestrial data be collected and interpreted in such pre-mining surveys. In British Columbia, planning procedures now exist which incorporate biophysical studies to help identify, assess and manage major environmental impacts associated with mine development.Methods outlined in the Guidelines for Coal Development (E.L.U.C., 1976) have been successfully applied in recent years. Following this example, the Inspection and Engineering Division of the B.C. Mineral Resources Branch prepared guidelines to help expedite the development of new base metal mines (Procedures for Obtaining Approval for Metal Mine Development; Ministry of Energy, Mines and PetroleumResources, 1979).The metal-mine guidelines require the proponent of a new mine development project to prepare a two-stage assessment proposal which systematically moves from a preliminary feasibility study (Stage I) to a final project design (Stage II), including application for regulatory approvals. One purpose of the Stage I report is to provide a description of the existing environmental conditions that could be affected by the proposed development. A preliminary environmental impact assessment should also be reported. The Stage II report will contain detailed assessment and management of environmental impacts."

Jan 1, 1981

By P. W. Udo Graefe

"An interactive computer model of a dragline, windrow and spoil pile has been developed for modelling oil sands mining operations. The model is to be used in conj unction with models of other oil sands mining equipment, such as bucket-wheel excavators and reclaimers, conveyors, hoppers, bins, trucks and shovels, to study mining operations on a minute-by-minute basis. From the orebody description and mining selectivity, layers of ore and reject are determined and mined by the dragline. Reject is dumped on the pit floor; ore is either dumped on a windrow for later removal by a bucket-wheel reclaimer or directly dumped into a hopper feeding a conveyor. The model allows for the presence of pads as a dragline base, key cuts and a number of interruptions to the mining operation such as shift changes, boom checks, engineering services, repairs, delays, preventative maintenance, etc. A CRT display keeps the model operator informed about equipment status and performance. The model operator can direct the course of the simulation by issuing commands to the model at any time during the simulation.IntroductionThis paper describes an interactive computer model of a dragline, windrow and spoil pile. The model was designed by the author based on information and specifications provided by Canstar Oil Sands Ltd. The model design was implemented and tested on Petro-Canda's IBM computer system by DMR and Associates Ltd. of Calgary, Alberta.The model was designed to form three components of an oil sands mining operations model, described in reference I. Figure 1 shows the interaction of those components with the remainder of the oil sands mining model.An ""Ore/Waste Body"" data base provides information to the dragline model about the location and composition of or e and waste in the mine. The dragline model is used to simulate mining this ore/waste body, to build up spoil piles for center reject (waste) and to dump ore onto windrows or hoppers (situated over conveyors) to deliver the ore to the extraction plant. The windrow model component provides a data base which will be used by a model of a bucket-wheel reclaimer which simulates the loading of ore from the windrow on to a conveyor via a bridge."

Jan 1, 1982

By R. J. Twigg, S. D. Chang

"The production of heavy water, the moderator in a CANDU reactor, is examined following a flow sheet of a typical Canadian plant. The process involves the extraction and concentration of deuterium from natural water through a chemical exchange mechanism with hydrogen sulphide. Consequently, corrosion problems associated with sour environments – the use of hydrogen sulphide - are an everyday problem and have led to the development of a highly refined materials selection and testing program to prevent equipment from failing prematurely.IntroductionHeavy water is a naturally occurring compound in ordinary water and is formed from the combination of two deuterium atoms and one atom of oxygen. Deuterium is a heavy hydrogen atom which has a nucleus of on e proton and one neutron. Hence, heavy water is a combination of heavy hydrogen and oxygen and is chemically known as deuterium oxide. It looks and tastes like ordinary water but it freezes at 3.8°C and boils at 101.4°C. The molecular weight of heavy water is 20 as compared to 18 for ordinary water; the density of heavy water is ten per cent greater than that of ordinary water.Although heavy water and ordinary water exhibit only small differences in their chemical and physical properties, there are large differences in their nuclear properties, the most important of which is the neutron moderating ratio, used to measure the ratio o f the slowing down power to the neutron capture characteristics. For heavy water the ratio is 21000 and for ordinary water it is 50. This high moderating ratio is essential for achieving a high neutron economy. Heavy water is, therefore, chosen as the moderating and heat transport fluid in the CANDU reactor."

Jan 1, 1983

By S. Srinivasan, R. Coté

"India is undergoing a massive electrification program using local coal to provide fuel for thermal generating plants. The Rajmahal mine in northern Bihar is scheduled to produce coal at the rate of 10 million tonnes per year by the end ofa sixty six month contract with MET-CHEM Canada Inc. for mine development. In order to control maintenance performance and warehouse inventory MET-CHEM is installing some proven computer-controlled programs and will provide extensive training to ensure that the systems are properly used. The programs are Maintenance Planning and Control System (MPCS) and Materials Management System (MMS), both of which were developed and used by Quebec Cartier Mining Company at its iron ore mine in northern Quebec. In addition, a Predictive Maintenance Program (PMP) using vibration analysis will be introduced . This paper discusses the three systems.IntroductionIndia is currently undergoing a massive countrywide industrialization and electrification program. Most of the power will be supplied by coal-fired thermal electric plants.One of the mines being developed as part of the over-all program is the Rajmahal Open Cast Coal project in the Godda District of Bihar, approximately 270 km north , and slightly west of Calcutta.The project is based on an agreement signed in January, 1989 between two government organizations - Canadian Commercial Corporation (Ccq and Coal India Limited (CIL). MET-CHEM Canada Inc. (MET-CHEM), an international consulting engineering organization which has worked in India since 1976, is CCCs Canadian executing agency for the project. METCHEM was the engineer-constructor and mining associate for the development of the 7.5 mtpy Kudremukh Iron Ore Project. This US$430 million project was completed on schedule and under the original budget estimate. The Rajmahal deposit is the responsibility of Eastern Coalfields Limited (ECL), a subsidiary of CIL. The project is to produce coal at the rate of 10.5 million tonnes per year in 1994."

Jan 1, 1991

By P. Mottahed, E. K. S. Passaris, J. Q. Ran

"The jointed roof of underground mine openings in stratified rock can be analyzed in terms of a voussoir beam. Because of the essential indeterminacy of the structure, previous attempts of theoretically solving the equilibrium equation have been unsuccessful. Numericalanalysisby the finite element method taking the geometrical and joint non-linearity into consideration combined with the experimental method has been adopted to study the performance isopara of the voussoir beam. Deformation and failure mechanism is analyzed in relation to the failure modes. Equations are proposed to estimate the elastic buckling strength and the crushing strength of the voussoir beam and to verify the failure mode of shear sliding. For application of the mechanism of the voussoir beam in mining operations, methods are described to predict the stability of a jointed roof and to design the dimensions of mining openings.IntroductionThe roof stability of an underground mine opening has direct effects on the selection of support methods, opening dimensions and, more importantly, on the safety of mining personnel. The prediction of the roof stability can be of importance in the design of a mining method and in mining operations. The jointed roof of mine openings in stratified rock can be stable under transverse load depending on the roof geometry and properties of the roof material and joints. The stability of this type of roof can be analyzed in terms of a voussoir beam which was introduced by Evans (1941) to study the strength of underground strata. Brady and Brown (1985) analyzed the voussoir beam and suggested that the mechanism of the voussoir beam could be used in the design of underground mine openings in stratified rock instead of the traditional continuous beam theory."

Jan 1, 1993

By J. Zollinger, J. R. Kennedy, E. Bouzy, B. Rouat, D. Daloz

"Ni-based superalloys have been replaced in the last low pressure stage of jet turbines for aircraft by titanium aluminides. In order to improve the properties of these Ti-Al alloys and extend their usage deeper into aircraft engines grain refinement by inoculation has been investigated. Borides are the most common inoculants for Ti-Al alloys, however they form brittle particles which are detrimental to the final properties of the alloy. Inoculants manufactured from a Ti-Al alloy with refractory metal additions were proposed to alleviate the issues arising from inoculation with brittle particles. An alloy was chosen which had less than 10% lattice mismatch with the alloy of interest (Ti-46Al) to maximize efficiency. Initial experimentation showed a decrease in as-cast grain size by a factor of 2 between the inoculated and non-inoculated samples along with an absence of the brittle particles found with boron inoculations. Investigations into the interaction between the inoculants and the melt were also carried out to better understand the inoculant size distribution and efficiency upon solidification.INTRODUCTIONTitanium aluminum alloys are an interesting material for aerospace applications. Their high temperature oxidation resistance and high specific strength make them particularly promising (Kim & Dimiduk, 1991). Recently, titanium aluminides have replaced nickel based superalloys in the last low pressure stage of the GEnx turbine engine. In order to increase their usefulness in turbines their properties must be improved for high temperature (>800oC) applications. Grain refinement is one method to improve the properties of a material, however current methods of grain refinement of Ti-Al alloys by inoculation have significant drawbacks. A new method of inoculating Ti-Al alloys by using Ti-Al alloys with small refractory metal additions (Nb, Ta) has been developed to avoid the drawbacks of current methods while still being effective grain refiners."

Jan 1, 2016

By G. Dubé, A. Leclerc, P. Quinn, G. E. Agar, J. Y. Clouthiér, J. D. McLaughlin

"Gold dissolution by cyanide requires the presence of oxygen which is usually supplied by sparging compressed air into the gold containing slurry. For those ores that contain certain obnoxious substances that consume oxygen, maintaining the required minimum level of dissolved oxygen can be troublesome. One of the most economical solutions to the problem of low dissolved oxygen, especially in plants that have air compressors installed, is to enhance the rate of oxygen mass transfer.The oxygen mass transfer rate was measured in a two phase system using two different sparger arrangements, and with addition of a frother that is known to reduce the bubble size produced by the sparger. The common sparger system was shown to be inefficient compared to a readily available but under utilized method of gas dispersion which introduces air directly below the reactor turbine. Transfer of this technology to an operating plant confirmed the beneficial effect of the improved sparger system. The addition of the frother did decrease the bubble size, but it also reduced the oxygen mass transfer rate."

Jan 1, 1993

By D. B. Langford, R. Hart

"This paper presents an overview of the state-of-the-art in industrial and utility power metering and control systems with particular emphasis on Digital Power Meters and Power Demand Controllers.IntroductionModern micro-processor technology, combined with very fast, high accuracy analog to digital converters, is rapidly allowing economical, digital power instrumentation systems to replace the traditional electro-mechanical meters and equipment previously used for instrumentation, control and protection in industrial power systems. Consequently, instrumentation and Supervisory, Control and Data Acquisition (SCADA) systems that were only practical for the very large utility or user are now available to smaller utilities and users. The information available includes sequence of event recording, trend logging, energy management cost allocation and automated load control, among others. The heart of any power monitoring system is the Digital Instrumentation Package (DIP) . These ""DIP's"" include Digital Power Meters (DPM's) and Power Demand Controllers (PDC's) as well as other specialized instrumentation packages such as Mini RTU's."

Jan 1, 1991