Search Documents

By D. Larouche, M. Mardan

Hot tearing is a complex defect in aluminium castings which is produced during solidification when a certain amount of liquid phase remains and weakens tensile resistance of the alloy. In direct chill casting of aluminium alloys, hot tears initiate at the surface of sheet ingots just after the primary cooling zone, where the microstructure is particularly vulnerable. In order to study the hot tearing susceptibility of these alloys, and the effect of grain refiners on their thermo-mechanical behavior , tensile tests were carried out in the semi-solid state ( ~95% solid) and at low strain rates using an apparatus called DCSS, for Direct Chill Surface Simulator. This apparatus, originally developed at Alcan Arvida R&D Centre (ARDC), is an instrumented rig test reproducing the conditions prevailing during the primary cooling stage of the DC casting process. The mechanical behavior of solidifying shells and the hot tear formation under applied tensile loads were measured and the occurrence of hot tearing was observed. Temperature in different locations of the casting, applied load and surface strain were monitored during the tensile tests conducted on aluminum alloys AA5182, AA6111 and AA3104. The microstructure of the tested samples was examined using the optical microscope to evaluate their columnar or equiaxed aspect and their effect on the mechanical response of the alloy. A special emphasis has been given to the evaluation of fractions solid existing in the castings at the start of the tensile tests, taking into account the local temperature, thermal gradient and cooling rates experienced. It was found that excessive grain refiner additions decreased the strength of solidifying shells because of the increased level of porosity induced by easier nucleation of new phases (gas included). It was also observed that cooling rates increased with the level of grain refiner, a phenomenon that was associated to the higher number of contact points obtained with small equiaxed grains. Finally, the concept of a stress based criterion for hot tearing was reinforced by the strengths obtained on not grain refined AA5182 and AA6111 showing similar fraction solid near the surface, but significantly different grain sizes.

Jan 1, 2006

By A. Gakwaya, P. Vachon-Joannette, P. Gagnon, J. Lévesque

"Predictive numerical methods are essential tools for reduced development cost and improved high performance designs of modern aircrafts. Their use leads to savings in terms of design cycle time and experimental trials. Composite materials subjected to impact loadings demonstrate various damage modes such as matrix cracking, fiber breakage, delamination and, ultimately, fabric fracture. Composite laminates are extensively used in the aerospace industry, and their damage modeling is complex due to their inhomogeneity and anisotropic behavior. Damage evolution affects both in-service properties and performance of these composites. In this work, the drop-weight impact test has been simulated. Using a material model that accounts for both delamination and intralaminar damage, laminates response is analysed using numerical simulations based on 3-D finite-element models of the commercial code Abaqus/Explicit. Experimental and simulation results are compared, in terms of energy absorption and contact force. The obtained numerical results show good agreement with experimental data.INTRODUCTIONAs primary aircraft structures are increasingly being made from advanced fiber-reinforced polymer matrix composites and are in general exposed to a variety of impact scenarios (bird, hail, debris etc.), an understanding of the impact event and the performance of composite materials during impact is important in the development of new structures. This work is focussed on low velocity impacts that typically occur when foreign objects hit the aircraft during maintenance or other on-the-ground operations. These impacts can cause non visible damage that affect the structural integrity of the composite components. While for metallic structures, damaging impact events typically leave noticeable dents due to plastic deformation, in contrast, for high strength carbon fiber reinforced composites, they can deform elastically to strain levels exceeding 1% and the internal damage can often occur without the formation of a visible dent. The identification and effect of impact damage on the performance of the structure is thus of great concern to the aircraft industry as the durability and damage tolerance of these composite structures are strongly influenced by the size of detectable internal damage."

Jan 1, 2016

By Michael Samis

NOFLEX valuation results ? CF deviations and net CF risk discount factors ??Cash flow deviations indicate average cash flow variability. ??Net cash flow riskdiscount factors (NCFRDFs) indicate the size of the risk adjustment applied to a cash flow. NCFRDFs profile should change with variations in cash flow uncertainty since the risk adjustments applied to the project cash flow reflect investor sensitivity to uncertainty.?DCF and RO will often produce different NCFRDFs for the same project since they use different methods of risk-adjustment.

May 1, 2006

By J. D. McFarlane, V. Robinson

"The paper begins with a brief account of the naturarly occurring resources of gypsum and anhydrite and a discussion of their relative value and utility as sources of sulphur. The fundamental chemistry of recovering sul-phur values from calcium sulphate is discussed. (a) Thermal decomposition -discussed as impracticable; (b) Reduction to calcium sulphide; (i) Total Reduction-The chemistry is outlined and the Dorr-Oliver and Bureau of Mines processes mentioned. The Elcor process is mentioned and certain deductions made from available information.(ii) Partial Reduction-This is stated as the basis of the only proven process, namely ""The Cement -Sulphuric Acid Process."" The possibility of recovering lime is mentioned as an aside, but dismissed for lack of commercial application. The history of the cement -sulphuric acid process is covered briefly and a list of plants in commercial operation included. A brief elementary account of the basic chemistry of cement production is followed by a discussion on raw materials and fuels. A short account of the flow scheme of a typical plant, with notes on the operating peculiarities, precedes an account of product quality. The latest developments which enable by-product gypsum to be used as a raw material are discussed, with an indication of how the flow scheme is modified. A statement of feasible plant capacities is followed by requirements of raw materials, services, labour, etc., and finally some indication is given of capital costs."

Jan 1, 1969

By S. Vaidya, R. C. McKellar, N. K. Sinha

Nominally [001]-oriented nickel-base single crystal (SX) superalloy CMSX-10 was investigated at 900°C under constant load, equivalent to an initial stress of 700 MPa, for creep strains from 7% to fracture strain (18.2%). The cross-sectional dimensions of initially uniform cylindrical specimens were measured along their entire length after the tests. The cross-section changed from circular to near elliptical shape. The anisotropic deformation, measured in terms of eccentricity, increased with the increasing strain level, but for a given strain level, it remained constant along the entire length of the initially uniform gauge section. The results are discussed in terms of diameter, eccentricity, area, local stress and microstructural observations. The most striking observation was the fact that all the specimens displayed a yoke-like shape, or the reduction of cross sectional area, at two locations within the originally uniform gauge section. Such observations have not been reported in the literature for single crystal superalloys.

Jan 1, 2006

By Y. G. Seredkin, A. A. Vasiliev, A. Y. Senchenko, A. V. Aksenov

"Autoclave oxidation, bacterial and chemical liberation, roasting, acid oxygen processes, atmospheric oxidation prior to cyanidation are applied to process refractory sulphide concentrates. It is obvious that the processes with the maximum effect regarding gold recovery are those in which complete destruction of sulphides takes place and gold becomes accessible for further cyanidation through liberation from sulphide “capsula”. But the significant recovery increase is often accompanied by a process complexity, high expenses for equipment purchase and maintenance. It makes material processing costinefficient. Process optimization has led to progress in ultrafine grinding, bacterial and autoclave oxidation processes. In our opinion sulphide atmospheric oxidation processes are the most interesting as oxidation there runs without high temperature (up to 100°?) and excess pressure (open units), and with acid environment close to neutral. The process of sulphide concentrates treatment named “Albion” (Albion Process™) represents a combination of ultrafine grinding and oxygen oxidation without pressure and external heating. The process has a number of advantages: sodium cyanide consumption decrease during gold leaching and high ecological compatibility. TOMS institute in collaboration with Glencore Technology Pty ltd (Australia) tested Albion technology aiming at liberation of finely disseminated gold from flotation concentrate produced from refractory ore of one Russian deposit. The testing has shown that Albion technology makes it possible to process refractory products with quite small capital investments. It enables involving medium and small refractory gold deposits into processing.INTRODUCTIONThe considerable part of the world Au-bearing reserves is present by refractory ores with finely disseminated gold. Gold in such ores is often associated with sulphide minerals and locked in so called “sulphide capsula” since it is closed inside dense sulphide grains and inaccessible to recovery by cyanidation. To treat refractory sulphide concentrates containing gold a number of processes were developed and they can be divided into three groups (Figure 1)."

Jan 1, 2016

By E. L. Jones

THE concentration of tin in the tailing from Sullivan ore has been de-scribed by H. R. Banks, superintendent of the Sullivan concentrator, in a paper presented at the annual meeting of the B.C. Division of the Institute in October, 1941(1). The reduction of the concentrate EARLY EXPERIMENTAL WORK Experimental work on the smelting of Sullivan tin concentrate was done in Trail. Preliminary tests in the laboratory indicated that the concentrate could be successfully treated in an electric furnace. A small electro-thermic pilot plant was built and, at the same time, reduction tests were made in an oil-fired reverberatory furnace. Both types of treatment gave satisfactory results. It developed that no fluxes, other than those already in the ore and in the ash of the reducing agent (either coke or coal), were needed. By using an excess of iron, a complete recovery of the tin in the slag was obtained, but with 20 to 30 per cent iron in the tin. A counter-current treatment was thus indicated, viz., the primary slag was first treated with hard-head (iron-tin alloy) from the refining and final slag smelting, producing tin with 2 to 4 per cent Fe. This secondary slag was subsequently treated with scrap iron to produce tin-iron alloy, and a final slag low enough in tin to waste. By following this line of endeavour, a tentative flow-sheet was drawn up and a successful operation was established. Without resorting to electrolytic refining, a metal comparable in purity to standard tin was produced. Metallurgical results and operating costs were found to be very similar with an electric furnace or a fuel-fired furnace. 'However, electric furnace smelting was chosen because the furnace required was smaller, and because some doubt existed as to the cleaning of the final slag in the reverberatory furnace reduction.

Jan 1, 1944

By G. Vibert Douglas

THE prospecter and geologist in the field, in the search for gold, are very often faced with a real difficulty. The: mineralized rock _frequently contains gold which is so finely divided or associated with sulphides that it is not recognizable in the gold pan. In recent years, the practice has been to take samples, send them to an assay office, and sit down and wait for results. This paper describes a method of solving the difficulty of proving the presence of this fine gold. The investigation is still in an experimental stage; but certain results have been obtained which would seem to justify publication. We do not consider that the method outlined is quantitative, but we believe that qualitative results are assured. The procedure has the great merit of simplicity. A sample of approximately two pounds of the mineralized rock should be taken and powdered as fine as is practicable. This powder is theo panned and the heavy minerals concentrated. Approximately two grams of these concentrates are taken for the test (one gram can be roughly gauged in the field by heaping up the powder on a Canadian twenty-five cent piece). The material is placed in a test-tube and 6 c.c. of a 10 per cent solution of iodine in alcohol are added (one-third of a test-tube full is approximately equal to 6 c.c.). Heat gently for about ten minutes over a spirit lamp, but without actual boiling. Allow to stand undisturbed until the sediment has settled to the bottom. Remove the clear iodine solution with an eye dropper. Allow it to fall, drop after drop, on a warmed pyrex watch-glass (the drops should be of equal size), taking care that the successive drops fall in the same place and that each drop evaporates before the next drop falls. Heat is applied to the lower side of the watch-glass by means of a spirit lamp. If gold is present in amounts of $2.00 or more per ton, a gold mirror will be formed on the watch-glass. This process of dropping and evaporating should be continued until no clear solution remains. If no mirror has appeared when all the solution has been used, another 6 c.c. of the iodine solution should be added to the powder and the process repeated. The absence of a mirror after the double treatment denotes an amount of gold less than two dollars per ton at the present price, or that the ore contains no gold. The mirror obtained must be washed with nitric acid ( 1: 1) to remove any copper, silver, lead, zinc, and iron. The yellow mirror remaining is pure gold.

Jan 1, 1937

By J. A. Finch

Samples of feed and product from a closed grinding circuit treating a heterogeneous lead-zinc ore were taken. The feed was subjected to laboratory batch grinding in a rod and ball mill with the objective of simulating the closed-circuit size distribution. It was concluded that the batch rod mill can closely simulate this product if only the over-all size is considered, but mineral-by-mineral large differences occur. If, as is suspected, the mineral sizes are the important factor in flotation, the differences could lead to problems in interpreting flotation results. An example of mineral recovery as a function of size is described to illustrate the potential problems.

Jan 1, 1979

By T. Schmidt, H. Assadi, F. Gartner, H. Kreye

Among all spraying processes, cold spraying has attracted a special attention in recent years, both as a coating - and more recently - as a rapid manufacturing technique. The interest in this process is mainly because of the fact that the deposition of spray material takes place at moderately low temperatures, and thus, oxidation and unfavourable microstructural changes can be alleviated. In this process, a highly compressed gas, flowing through a de Laval nozzle, accelerates the particles of the spray powder to high velocities of up to 1200 m/s. Although there is no melting of particles prior to impact on the substrate, cold-sprayed deposits can be denser and more tightly bonded as compared to the equivalent deposits produced by conventional thermal spraying methods. The present contribution focuses on this unique aspect of cold spraying. Modelling of particle impact, combined with various experimental observations, is employed to illustrate that bonding of particles and hence material deposition occurs through shear instability - associated with severe plastic deformation and localized heat generation - at the interacting surfaces of particles and substrate. The results of modelling also provide an insight to the influence of material and process parameters on the critical velocity and on the microstructural properties of cold-sprayed deposits.

Jan 1, 2006

By P Kovacs, D. L. Flock

For the purpose of reservoir-performance calculations a balance can be made between the materials with-in the reservoir and the production from the reservoir. The material balance equation, a relationship which holds under or near equilibrium conditions, has been used in many forms by the Petroleum Engineer for the determination of initial oil-in-place in the reservoir and the calculation of performance into the future. One of the more recent methods developed by Tracy, utilizes a modified form of the Schilthuis material balance. In the latter case, values of incremental production are assumed for a particular pressure drop, a value of the gas-oil ratio found and a check of this estimate made by calculation"' the initial oil-in-place. Tracy's method utilizes an estimation of the instantaneous gas-oil ratio and by trial and error a value of the gas-oil ratio is

Jan 1, 1961

By D. A. Akinlade, N. L. Richards, D. C. Murray, W. F. Caley

To investigate the effect of adding Ti to a Ni-Cr-Fe powder metallurgy alloy, a thermodynamic software package was used to predict the phase transformations that occurred during thermal processing. Specifically, the effect of adding 3w/o Ti to a 6w/o Al modified ternary Ni-Cr-Fe alloy (the quaternary) was simulated and the phase transformations that might occur in the material on sintering were obtained using the thermodynamic modeling tool. These predictions were subsequently compared with experimental results obtained by X-ray diffraction and metallography. For comparison, selected compacts were prepared containing only the ternary + 3w/o Ti (no Al). Based upon compressibility curves, the optimum pressure for producing the new Ti compacts was 500 MPa vs 600 MPa for the quaternary composition with Ti. In each case, hardness of the base alloy was enhanced by the Ti addition whereas the residual porosity remained relatively constant at about 19%. Finally, although SEM/EDS failed to confirm the presence of Ti in the gamma prime intermetallic, XRD spectra showed a shift in lattice parameter on addition of Ti, suggesting that the intermetallic was of the form Ni3(Al,Ti).

Jan 1, 2010

By A. Kraly, M. Complojer, P. Paschen, K. Gamweger, H. Antrekowitsch

Increasing quality of aluminium alloys and continuous optimization of the production process leads to an improvement of the gas purging systems. The application of porous plugs for the treatment of liquid aluminum is nowadays not widely used in the aluminium industry especially in Europe. The Department of Nonferrous Metallurgy and the Christian Doppler Laboratory of Secondary Metallurgy of Nonferrous Metals intensified the research and development of refining and alloying processes by gas treatment during the last years. CFD-modeling supports these experiments, which should lead to lower hydrogen content, lower suspended particles and a better distribution of alloying elements in the melt. Different parameters such as temperature, bubble size, gas amount and which kind of gas is used influence the quality of the products.

Jan 1, 2006

By Y. Obara, A. Sato

"Limestone is one of the most important mineral resources, and in Japan it is only one mineral which can be fully supplied by the domestic product. Generally limestone mines in Japan located at mountainous regions, and the combination between bench-cut method and the carry-out system using vertical shaft is widely used in the domestic mines. During mining operations, the occurrence of the blockage in the vertical shafts is very serious problem. Once the blockage in the shafts is occurred, a lot of works and dangerous procedures are necessary to solve the problems. It is thought that blockage is influenced by the cohesion and friction coefficient due to clay minerals thrown into the vertical shafts, however, the quantitative and precise reason is not revealed yet.In this study, the process of blockage occurrence was simulated by 2-Dimensional Discrete Element Method (DEM). In the 2D-DEM analysis, discontinuous circular particles are generated, and the individual movement of each particle is calculated by forward difference method. In the analysis, several typical ore distributions are applied, and the DEM analysis was conducted under the various combinations of cohesion and friction coefficient. From analytical results, it was found that the friction coefficient strongly influences to the occurrence of blockage and there were a threshold values which blockage does not occur. Several kinds of shaft shape were also simulated towards different ore size distributions, and those influences to the blockage occurrence were also discussed."

Jan 1, 2015

By F. Hassani, J. Peck, D. J. Lucifora

The performance of a rotary blasthole drill is heavily dependent on the material being drilled. This material is a microcosm of the in-situ geology that makes up the surface mine in which the rotary blasthole drill is deployed. The performance metrics that are influenced by the in-situ geology are penetration rate (distance drilled per unit time), rotary torque and to a lesser extent rotary speed and vibration. For simulation and testing purposes it is useful to have a validated plant model based upon the application of study. Once validated, a plant model can be used to perform simulation based testing as a supplement and possibly in place of more expensive and logistically complex field testing. Previous studies in the field of rock mechanics have supplied proven models that relate the performance of a rotary blasthole drill to the material being drilled for a given rock type with a given drill bit. In this study, field based experiments were conducted in an active surface mine on a working rotary blasthole drill and the corresponding monitoring while drilling (MWD) data was recorded. Data analysis was then performed on the collected field data. The techniques used successfully fit the collected MWD data to the previously proven rock mechanic models. This paper explores the theory relating rotary blasthole drill performance to the material being drilled, illustrates the required data collection and data analysis techniques, and demonstrates the ability of these techniques and the known rock mechanic models to provide a simulated plant model for the drilling process that can then be validated. This validation is also discussed.

Jan 1, 2015

By Y. Sugiyama, K. Kitazono, T. Miura, K. Matsuo

"Impact energy absorbing system for automotive is an important technology. Open-cell porous aluminum alloys were manufactured through Powder Bed Fusion (PBF) process. Compressive properties of the porous aluminum alloy depend on the cell structure as well as the porosity. The authors manufactured two ordered cell structures, truncated octahedron and rhombic dodecahedron, and one disordered cell structure, random Voronoi structure using a 3D-CAD software. Compression tests revealed the anisotropic deformation of the porous aluminum alloy with ordered cell structure. On the other hand, the porous aluminum alloy with disordered cell structure showed relatively isotropic and uniform deformation, which is suitable for energy absorbing applications. Therefore, controlling the disordered cell structure designed by Voronoi diagram enables to develop the advanced porous aluminum alloy having various mechanical properties.INTRODUCTIONAdditive manufacturing (AM) process enables to manufacture near net-shape mechanical parts. The AM technology is typically focused on titanium alloys due to their high specific strength and biocompatibility (Attar, 2014). Recently, aluminum alloy parts can be manufactured through selective laser melting method (Leary, 2016). Metal foams or porous metals are lightweight cellular materials having closed-or open-cell structures (Banhart, 2001). Aluminum foams are focused on as an energy absorbing material for transport industries (Baumeister, 1997). The purpose of the present study is to investigate the optimal cell structure of open-cell porous aluminum alloy manufactured through AM process. Most previous researches on the AM aluminum lattice structure has been considered ordered and periodic cell structures. On the other hand, classical aluminum foams manufactured through cast or powder metallurgical processes have disordered and heterogeneous cell structures (Körner, 2000). The authors use a concept of Voronoi diagram (Moukarzel, 1993) in order to manufacture various cell structures."

Jan 1, 2018

By G. Tairova, J. Ioffe

Arsenic, selenium and mercury species are common contaminants in mining aqueous streams and present significant environmental and health problems. The objective of this project is to investigate methods to lower the concentrations of these elements in mining aqueous streams. A new composite media for removal of these elements of concern from mining effluents was developed. The results of bench scale and pilot plant experiments, using the media, indicated removal of arsenic, selenium, mercury and other elements of concern below detection limits.

Jan 1, 2014

By Charlie Jefferson

Main Goal: Resource Assessment 1. Incorporate existing data & results, old process. 2. NEW Quantitative Analysis (Chung and Chen) 3. Try mass balance of U and geochemical tracers 4. Use holistic process approach ?with key foci ?Targeted basin / belt assessments ?Is there as much in the Athabascaas they say? ?Athabasca reference for other basins (Thelon, etc) ?Compare sandstone & volcanic with USA, Kazakhstan etc: do their models apply here? ?Which IOCG systems are prospective for uranium? 5.Consider Groundwater, Environment; 6.Communicate

May 1, 2006

By Simon Weixiao Sun

Conventionally, carbon steel has been the primary material for salt mine headframe construction, protected by specialty paint layers to prevent corrosion. These layers require meticulous QA/QC during fabrication and erection, and the top UV protection layer typically loses effectiveness after an average of 10 years, necessitating ongoing maintenance. As headframes age, significant structural repairs are often required. Alternatively, stainless steel can eliminate corrosion concerns, though its high initial cost has limited its use in headframe design. However, when factoring in long-term maintenance costs, a 'maintenance-free' stainless steel headframe can be an attractive option for stakeholders. This paper compares the structural performance and economic considerations of painted carbon steel and stainless steel headframes, including initial capital and long-term maintenance costs. Additionally, it explores a hybrid approach, strategically using carbon steel in low-contamination areas to reduce initial costs and significantly minimize future maintenance efforts.

May 4, 2025

By A. C. Hatton

Doped SrCoO3.8 was found to be a promising material for use as a cathode component in intermediate temperature SOFCs. In this work, strontium cobaltite ceramics doped with 10 mol% to 90 mol% samarium were synthesized using the glycine nitrate process in order to study the electrical conductivity and thermal expansion at temperatures of up to 800°C. As-synthesized powders were deagglomerated, pressed and sintered at temperatures ranging from 1100-1250°C. The effect of temperature and composition on electrical conductivity and thermal expansion are presented and discussed.

Jan 1, 2005