Search Documents

By S. A. Jacob

Magnesium sheet is notoriously difficult to form at low temperatures without initiating failure, In the present work cold rolling and annealing conditions are varied to produce samples of AZ3lB sheet with a range of grain sizes. The formability of these samples is investigated using tensile testing and forming limit diagrams (FLD's), The results are discussed in terms of twin types and frequencies.

Jan 1, 2005

By J. J. Benitez

MIBC (methyl-isobuthyl carbinol) was previously shown to enhance significantly sylvite flotation when used at the stage of preparation of amine dispersions. In this paper Atomic Force Microscopy (AFM) is used to study the effect of MIBC on deposition of octadecylamine (ODA) on the surface of mica. The AFM images indicate that amino terminated, and therefore hydrophilic, deposits of ODA are observed on the mica surface in the ODA dispersions free of MIBC. In the presence of MIBC a methyl terminated (hydrophobic) monolayer is obtained on the mica surface. The transition between the monolayer and bilayer phases is due to the presence of MIBC. Experiments carried out in distilled water reproduced the results obtained from the brine. Working in pure water instead of brine simplifies the preparation conditions and the analysis by AFM.

Jan 1, 2006

By Roland Hunt

This paper deals with the practical problems as sociated with blasting a heated pillar remnant. This pillar remnant was the final stage in the blasting of a multi-stag e pillar blast. Production from the previous stages had produced burning sulphide ore, resulting in high rock temperatures in the final unblasted stage. This is an account of how, under difficult conditions, the pillar remnant was blasted.

Jan 1, 1977

By R. Browner, J. Collard, D. Ibana

The extraction of cobalt from synthetic pressure acid leach solutions of nickel laterite ores by the direct solvent extraction route using ESPLIM is reported. It first explored the use of gaseous ammonia as pH modifier and then the variables that affect the dispersion of the aqueous phase in the organic phase such as ionic strength, viscosity of the phases, initial droplet size, etc. were explored so that phase hold-up and thus extraction can be effectively controlled. The results show that the technique allows better control of phase dispersion circumventing one of the main weaknesses of conventional solvent extraction.

Jan 1, 2005

By C. Cortés

Flotation is a highly interactive process where a change or disturbance in any part of the circuit results in different final grades and recoveries. This high variability of the circuit metallurgical performance complicates the diagnosis of the scavenger stage at the end of the line, as copper losses in the final tailings are erratic and not totally a consequence of problems in the scavenger section. The assessment of the scavenger performance requires a more elaborated procedure than that used for others stages of the circuit. This communication describes the application of an approach that combines results of laboratory flotation tests with those of surveys performed at the plant. The approach is based on running surveys in one of the circuit lines to collect samples for determining grade vs. recovery curves for total mass and size-by-size fractions. Full mineralogical and liberation analyses are also considered on some samples of the feed and tailings streams selected to have a range of feed grades. A separate sample of the feed is used to run laboratory flotation tests to determine optimum flotation time. Two additional pieces of information are the effect of operating variables on recovery, determined through a test program based on design of experiment techniques, and operational data on every cell in the line gathered by visual observation. The application of this approach to one of the scavenger lines at Los Colorados concentrator (Minera Escondida, BHP Billiton) is demonstrated.

Jan 1, 2007

By K. T. Aye

An investigation into the leaching of chalcocite and covellite in cyanide solutions at concentrations typically encountered daring gold cyanidation has been conducted. The results indicate that, for both minerals, the extent of leaching is greater under anoxic conditions, but is still incomplete even in the presence of free cyanide ions, with undissolved copper solids remaining in equilibrium with solution species. The speciation of the sulfur and cyanide reaction products in solution are interpreted in terms of the fast formation of a copper(I)- cyanide complexes in solution and a sulfur-rich copper(I) polysulfide solid phase, which then reacts more slowly to produce thiocyanate ions.

Jan 1, 2011

By Y. Wang

In this paper, the tribological and electrochemical corrosion properties of Al2O3/polymer nanocomposite coatings were studied using a micro-hardness test, a single-pass scratch test, an abrasive-wear test, and finally an electrochemical technique such as potentiodynamic polarization measurement, The coatings containing Al2O3 nanoparticles showed improvement in scratch and abrasive resistance compared with polymer coatings; this improvement is attributed to the dispersion hardening of Al2O3 nanoparticles in polymer coatings, Corrosion test results showed that the embedded Al2O3 nanoparticles in the polymer matrix do not sacrifice the corrosion resistance of the polymer itself.

Jan 1, 2005

By C. O. Staples, J. G. Morrow

The application of cationic flotation to the upgrading of magnetic concentrates was investigated in the laboratory by both batch and continuous test procedures. It was found that the collection of coarse gangue particles with amine, heretofore considered a serious obstacle to this particular application of cationic flotation, is greatly enhanced by a drastic reduction in what might otherwise be considered normal impeller speed. Gangue flotation is in-dependent of variations in the rate of aeration. The collector and Crother additions and the impeller speed which favour the formation of a matte froth yield optimum results.

Jan 1, 1966

By Finch. J. A., C. Perez, J. M. Ortiz, G. Cortes, A. B. Yañiez, F. Coddou, P. Morales, H. Elgueta

A campaign to perform characterization tests in a TankCell®-300 flotation cell installed at Chuquicamata Codelco's concentrator was conducted. The campaign included integrated gas dispersion measurements (gas velocity radial mapping and single point gas holdup and bubble size) and determination of frother concentration. Cell streams were sampled to assess metallurgical performance at the same time. The experimental program was designed to establish the bubble surface area flux operating range and its effect on performance, and the effect of using longer residence times and of a device designed to enhance mixing in the collection zone (FlowBooster(TM)). The gas dispersion results and their relationship to metallurgical performance are discussed.

Jan 1, 2009

By S. M. Taghavi, M. Halali

This paper investigates the possibility of zinc oxide production from zinc ore concentration residues, and also the effect of temperature, time and depth of bed on waste materials reduction percents. The results obtained show a significant increase of the reduction percent as a function of time and temperature. With increasing in depth of bed, reduction percent will decrease. Maximum zinc oxide percent in products was 93.5%.

Jan 1, 2004

By K. Thuro, L. Wilfing, H. Kasling

"In mechanized tunneling, performance prediction is a crucial issue for estimating excavation costs and construction time of a tunnel project. The aim of this work is to compare the calculated parameters by penetration prediction models with the results of penetration tests during excavation by a Tunnel Boring Machine (TBM) at actual tunnel projects. This comparison helps to improve the existing prediction models (Gehring, 1995 and Rostami (Colorado School of Mines), 1997.) and to develop a new, so-called “Alpine Model” (research group ABROCK; Schneider et al., 2012).On-site penetration tests are a common tool to determine performance of a TBM in certain geological environments. During a test, the TBM is operated under defined conditions that allow comparing the results of different projects and machine types. There are two different types of penetration tests in use. The more common type, described by Bruland (1998a), is based on test drives at different thrust levels. The tests in this study are performed as start-stop-tests, meaning that the TBM starts from zero to the maximum possible thrust and reverse with slowly increasing respectively decreasing steps (Frenzel et al., 2012). To gain information about the interaction between TBM and rock mass, a detailed geological documentation including an analysis of the discontinuity pattern and laboratory testing for rock strength characterization are mandatory.Within the last year 16 penetration tests have been performed. The results are thrust- penetration curves (Figure 2) showing that up to a certain penetration rate only crushing occurs (subcritical penetration). From there the desired rock fragmentation process called chipping takes place (Frenzel et al., 2012). These two different fragmentation processes can be described best by a bilinear function as seen in Figure 3. Both, CSM- and Gehring-model, do not fit to the trend of the penetration rates determined during the excavation process as they are using potential or simple linear functions.Another parameter that has to be implemented into the new prediction model is the influence of discontinuities. In case of favorable orientation and spacing, discontinuities reduce the required thrust at same penetration rates. In contrast, unfavorable discontinuity systems can cause blocky faces and hence worse performance than predicted. Besides discontinuities, the toughness of rocks has to be taken into account when predicting the penetration as tough rocks need more energy to obtain complete failure than brittle rocks.Key advantage of these tests in comparison to existing are more data points in less time. By improving respectively extending the existing penetration prediction models with the stated parameters, the penetration prediction for TBMs can be more accurate and also wear calculation can benefit from this approach."

Jan 1, 2015

By A. Zarei-Hanzaki, O. Golmahalleh, S. M. H. Hosseini, H. Azizi-Alizamini

The main importance of acicular ferrite microstructures arises from their desired combination of mechanical properties in comparison with the bainite and ferrite-pearlite microstructures. Several factors affect the microstructural transition from bainite microstructure into the acicular ferrite one. As is well established any factor corrupting the prior austenitc grain boundaries nucleation potential, such as the thin layer of allotriomorph ferrite and the austenitc deformation inhomogenities may promote the acicular ferrite formation instead of bainite. Accordingly, this study deals with the effects of the aforementioned features on the acicular ferrite formation in low carbon microalloyed steel. The results indicate that the formation of strain-induced ferrite at the prior austenite grain boundaries accompanied by deformation inhomogenities in the austenite grains change the effectiveness of allotriomorph ferrite on acicular ferrite formation from active to inert one.

Jan 1, 2004

By David McMullen

Radiation plays a critical role in the thermal behaviour of hydrometallurgical process equipment. This effect is particularly important when designing refractory lined equipment used in pressure leach/oxidation processes. In order to simplify this non-linear mode of heat transfer, the effects of radiation had previously been incorporated in an equivalent convective film coefficient in finite element methods (FEM). This prior method omits the effects of radiosity, a critical aspect of radiation heat transfer, which affects the design of refractory lining systems in autoclave vessels. Given that 60% of the heat loss in actual plant practice of an autoclave is due to radiation, reliability in the FEM is therefore impacted. This study validates the use of radiosity in FEM through thermal loading using a combination of simple geometries to be applied to complex environments such as vessel nozzle clusters. The added benefits of using a radiosity load includes an increase in confidence in thermal distribution results, greater accuracy in determining appropriate refractory lining systems, weld overlay sizing, and increased accuracy in structural analysis.

Jan 1, 2014

By d&apos, F. Elia

Hot cracking of magnesium (Mg) alloys during welding creates a barrier to enhancing the use of these alloys in automotive applications. As a result, it is imperative to understand the mechanisms responsible for hot cracking of Mg alloy welds in order to develop means of eliminating this problem. In this study, the hot cracking susceptibility of AZ91E and AE42 magnesium alloys were assessed using the moving torch Varestraint test method. Plates of 3 mm thickness were extracted from AZ91E and AE42 ingots and subsequently tested. Quantitative cracking data in terms of maximum crack length (MCL) was used for evaluating the cracking susceptibility. Scanning electron microscopy was carried out. The results suggest that AE42 showed a higher resistance to hot cracking in comparison to the AZ91E alloy. This was attributed to the difference in microstructure between the two alloys. In the fusion zone and HAZ of AE42, the brittle needle-like A1IIRE3 phase was seen to decompose to the more ductile particle-like Al2RE phase, thereby increasing the alloy's resistance to hot cracking. In contrast, SEM fractography revealed that brittle A16Mn and Mg17A112 intermetallic particles segregated to grain boundaries and triggered hot cracking in AZ91E.

Jan 1, 2011

By C. M. Acuna, M. Sherrington

In high temperature processes thermodynamic equilibrium is assumed and therefore chemical potential of elements, among the condensed phases, have to be the same. In such situation impurities distribute accordingly and their fractional distributions are affected by the masses of the coexisting phases. It has been claimed Teniente Converters perform quite well for smelting high impurity concentrates, especially in respect to volatilization and/or slagging. Production of high matte grade near white metal composition, requiring moderate oxygen enrichment in the process air, results in a huge mass of gas and therefore a high fraction of impurities report to it. Similarly, by recycling different sources of slag, flue dust or other materials, the mass of the final slag is increased and so do the masses of impurities reporting to the slag. Nevertheless, above a certain level the recycling of smelter byproducts is no longer feasible and the cycle has to be halted, unless higher impurity mattes are accepted. Although the process might be continued during converting and refining, lengthy and expensive measures have to be taken if suitable anode copper for electrolytic refining is to be achieved. In the present study samples of high arsenic matte grade and slag were obtained on a pilot scale. The matte samples, on the order 75%Cu, were equilibrated with slag at varying ratios in magnesia crucibles under CO/C02 atmospheres at 1523 K. After 24 hours equilibrium matte and slag were rapidly solidified and analyzed by copper, sulfur, iron and arsenic. Furthermore, industrial samples of matte and slag, in the order 75%Cu at 1523 K, were obtained via a special quenching sampling device to determine the association of copper and suspension of matte and copper in slag. Based on the results, the distribution coefficient of arsenic between slag and matte was evaluated along with copper species in slag and the fractional distribution of arsenic, in the coexisting phases, was determined as a function of the ratio mass of slag to mass of matte.

Jan 1, 2007

By J. P. Weiler

The increasing use of high-pressure die-cast magnesium alloys in the automobile industry requires a better understanding of the mechanical properties, the microstructure, and particularly, the relationship between these two. The goal of this study is to first understand the microstructural features which control the mechanical properties observed from an AM6OB magnesium alloy, and second, to be able to predict the local mechanical properties based on microstructural features encountered in different areas of the die-cast component. The two main tools used in this study are spherical indentation testing, used on local areas of the die-cast magnesium alloy AM6OB to detect changes in microstructure and mechanical properties, and X-ray tomography, used to non-destructively investigate the internal porosity in a sample. The results from these tests are then used to predict the local mechanical properties such as the yield stress, the strain-hardening characteristics, and the fracture properties of the AM6OB component.

Jan 1, 2006

By M. R. Julien

"The geomechanical behavior of rocksalt shows very distinctive features. The response of this most ductile of all low porosity rocks is dominated by inelastic processes that are strongly time- and historydependent. These characteristics must be taken into account when analyzing underground openings. Different constitutive models have been proposed and used for this purpose, and this paper presents the general formulation and applications of one of these. The SUVIC model relies on a unified approach with internal state variables producing mixed hardening to represent the inelastic behavior, which lead to specific solutions for plasticity and creep. The model equations have been implemented into a finite element code to perform numerical analyses. Simulations results are presented to show that this model captures essential aspects of rocksalt behavior under simple and complex laboratory testing conditions. Simulations are also conducted to analyze the response of underground openings. INTRODUCTIONPredicting the response of man-made excavations in rocksalt can be quite a challenge as it requires a reliable constitutive model to represent the material behavior. This softest of all low porosity rocks shows a highly non-linear inelastic behavior, very sensitive to history and rate effects (e.g. Senseny et al., 1993; Cristescu & Hunsche, 1997; Julien, 1999; Wittdke, 2014). The many deformation (micro) mechanisms acting locally in rocksalt make the construction of appropriate constitutive equations quite complex. Nonetheless, there have been significant progresses made over the last two decades or so; many of these developments have been included in a series of specialized Conferences Proceedings (Ghoreychi et al., 1996; Aubertin & Hardy, 1998; Cristescu et al., 2002; Wallner et al., 2007; Bérest et al., 2012)."

Jan 1, 2015

By P. Plante

Contaminated neutral drainage (CND) is characterized by the presence of metal concentrations above regulatory requirements at circumneutral pH in mine drainage. The generation of CND by tailings and waste rocks is a growing concern for the mining industry due to increasingly restrictive regulatory requirements. Difficulties in CND prediction arise from the low oxidation rates of sulfide minerals and from the metal retention potential within the wastes. In fact, sorption phenomena may induce an important delay in the development of CND. For now, it is not possible to adequately consider this delay using the prediction tools developed for acid-mine drainage, such as humidity cells, columns and lysimeters. This work aims to present the new approaches currently under study for CND prediction, particularly the use of a chelating agent in kinetic tests. The main challenge of CND prediction is to quantify the metal retention potential of mine wastes, especially when sorption phenomena are involved in metal retention. Three approaches are currently used to overcome this difficulty. Firstly, the sorption potential is estimated using batch sorption studies. The second approach consists of artificially saturating the sorption potential of the mine waste by contact with a contaminated leachate in sorption-enabling conditions until saturation of the retention potential. These approaches both require that the possible metals involved in CND are known (as well as their chemical speciation) prior to the tests, which require an exhaustive material characterization. Although the two methods enable a qualitative estimation of the retention potential of mine wastes, their results are difficult to scale up from the laboratory to the field since some important parameters are not taken into account. A third proposed approach consists of inhibiting metal sorption at the source using chelating agents. The hypothesis is that chelating the metals immediately upon their release from the oxidation of sulfide minerals will inhibit all geochemical interactions (sorption, complexation, secondary mineral precipitation, ion exchange, etc.) between the metal and its environment. The ideal chelating agent will inhibit geochemical interactions after metal release in the drainage waters without having any impact on the sulfide oxidation and acid neutralisation rates. These approaches were tested over a waste rock sample that is known to naturally generate CND after a few decades of weathering. Results show that kinetic testing (weathering cell, ± 70 g samples) using a chelating agent (EDTA) in the leaching water renders higher metal concentrations in the leachates than a control sample without EDTA, suggesting that sorption (and possibly other geochemical interactions) is inhibited. These results suggest that the combination of these approaches can be efficiently used for more precise CND prediction from mine wastes. Future work will be done using the chelating agent approach over larger scale tests such as columns (± 80 kg samples) and field cells (± 100 tons) in order to propose an integrated approach for CND prediction.

Aug 1, 2013

By Atulya Verma, Samantha Espley, Nashel Kalaka

Numerical modelling simulations of proposed mining sequences are used to evaluate mining induced stress concentrations and their migration associated with the progress of mining. This analysis is a standard practice for most prospective mining projects at various levels of feasibility study. The studies are usually initiated at the beginning of the mining cycle, on a global scale, and are maintained and updated throughout the life of mine (LoM) to identify or address local issues and the required remedies as and when needed. Developments in numerical modeling techniques along with advancements in computing technology and data storage/management capacity have given rock engineers access to a huge volume of data that needs to be analyzed and assessed. The most common approach to numerically evaluate stress concentrations and migrations in underground mines is to select the points of interest in a given volume such as the back of an excavation or points within pillars around critical infrastructure, and plot the stresses or a derivative of stresses over time to represent life of mine concentrations and migrations of stresses. The problem with this approach is the sharp gradient of stresses close to excavation boundaries. Slight changes in the location of selected points can change the stress concentration and migration patterns substantially and all generalized statements about LoM risk can be challenged in one way or another. For global stresses, the most common current approach of data analysis is by viewing series of pictures representing stress contours. In this approach, it is easy to overlook some critical detail and/or be masked by personal preferences of contour/picture representation. To overcome the problem of representing and analyzing huge volume of stress simulation data, the authors, through their experience at different mining operations, developed a volume-based technique to reliably evaluate mining-induced stress concentrations and migrations. The volume-based approach is for risk-based assessments of adjacent regions in the rockmass, in and around planned stoping excavations. The volume of interest is the entire ore body that is planned to be mined, but it could be just a part of the ore body depending on the specific use case. The risk identifiers are the induced stresses as compared to the strength of the rockmass. Over the LoM, the risk identifiers are tracked versus the corresponding excavation ratio of the zone. This approach is very effective in identifying the stages of mining that are contributing the most to the mining induced stress risk and the results can be used for proactive planning and mitigations measures such as alternative mining sequences, or stope sizes, or extraction methods. The approach has also been very successful in application at mature mines, particularly in assessing the re-initiation of mining in zone that has been dormant for some time. The volume-based approach allows for an assessment of the current state of the rockmass and the identification of future risks when planning resumption of mining activities.

Jan 1, 2023

By J. Álvarez, J. Mesías, C. O. Gómez

"Operations routinely run flotation tests in laboratory mechanical cells to determine adjustments to plant operation based on feed flotation response or the effect of new reagents and dosages. The metallurgical results of these tests are certainly affected by changes in bubble size, which simultaneously impact the recoveries of the collection and froth zones. It is known that bubble size depends on the characteristics and operation of the machine in use, particularly on the gas flow rate delivered to the unit and the selected frother type and dosage. Although flotation rate constants have been related to bubble size, bubble surface area flux seems to be a more fitting variable to correlate flotation kinetics and cell performance, as it integrates bubble size and superficial gas velocity effects. However, although some evidence has been provided, a categorical relationship between cell recovery and bubble surface area flux has not been established. Our interest is to demonstrate this relationship to use it as a basis for developing soft sensors to track on-line collection zone recovery in cells. Flotation tests were designed to produce Cu concentrates for a range of bubble surface area flux values, obtained through changes in frother concentration at a constant gas flow rate, and by increasing gas flow rate at the same frother concentration. The tests were run on samples prepared from an ore batch supplied by a local operation, following strict grinding and flotation procedures, with a shallow froth to approximate cell recovery to that in the collection zone. Bubble sizes were determined using the sampling-for-imaging technique developed at McGill. The results unequivocally showed a consistent positive correlation between cell recovery and bubble surface area flux, and significant variations in performance when frother addition and gas flow rate were changed.INTRODUCTIONMineral flotation is a separation process to produce concentrates of valuable minerals by selective attachment of particles to the surface of bubbles. The process is carried out in machines where air is injected through a mineral pulp to form bubbles, and operated to create two zones: a bottom one (collection zone) where bubbles are continuously generated under conditions adequate to form bubble-particle aggregates by collision of the rising bubbles with suspended particles; and a top one (froth zone) where bubbles and bubble-particle aggregates continue to rise while concentrating and forming a froth layer for water and entrained particles to drain back to the collection zone, before overflowing as a concentrate stream. The phenomena occurring in these zones are complex and, in many cases, interactive, as they simultaneously affect stages of the particle separation sequence occurring in both zones. Although there have been significant advances in instrumentation to characterize particle and bubble populations, these have not resulted in knowledge to explain or models to describe phenomena from fundamental principles. Measurements continue to be limited to the development of empirical models for predicting the effect of operating variables on performance."

Jan 1, 2016