Search Documents

By P. C. Parsons, G. C. Milligan

"IN FIELD WORK in the Cape Breton Highlands, which are heavily covered with vegetation, it is necessary to run traverses along the valleys of small brooks. We encountered difficulty in closing such traverses, and the following technique was developed to solve this problem. It has been tested in the field for four seasons by several people, and found to be simple, efficient and more accurate than any other compass-and-pace system of which we are aware. So far as we can find, the technique has not been described previously. It may be of use to others.The Cape Breton Highlands of Nova Scotia consist of hills of old intrusive and metamorphosed sedimentary rocks protruding up to 1,000 feet above the general level of the younger sediments which underlie the valleys. The flat hill-tops are the remnants of a plateau; drainage off the edge of this plateau has produced many small steep brooks. They occupy valleys which are up to 800 feet deep, and V-shaped in cross section, with steep sides covered by mixed conifers and hardwoods. The stream at the bottom is rarely more than a few feet wide, with a negligible meander belt, but with many bends, rapids and falls. Visibility along the stream, in consequence, is rarely more than a few hundred feet, and in many places much less.It was found impractical to map the streams by the method of meander lines, as described in many standard surveying texts and hand-books. The limited visibility, and the numerous bends of the brooks, necessitated many corners. Every corner introduces errors. To 'close' a survey with 40 or 50 such corners proved either very time-consuming or impossible. In most cases, however, the general direction of a valley may be obtained from an aerial photograph, or by direct observation, and this became the basis of the method adopted."

Jan 1, 1971

By A. H. Lang

THE recent production of important quantities of high-grade muscovite at the Purdy mine, near Eau Claire, Ontario, bas brought that district into prominence and bas added another strategic mineral to the list of Canadian products. The discoveries are thirteen miles west of Mattawa and about two miles north of the Trans-Canada highway and the Canadian Pacific railway. HISTORY Clear mica of low power factor is in considerable demand in Canada and in the United States for war purposes such as radio and telephone condensers, aircraft spark-plugs, radio tubes, and transformers. Some muscovite (white mica) bas been produced in North Carolina and New Hampshire, but the United States trade bas depended largely on importations of muscovite from India and of phlogopite (amber mica) from Madagascar. For many years Canada bas been a substantial producer of phlogopite, but was unable to compete extensively in the United States with importations from abroad. Canadian production of muscovite bas been negligible as no important deposits were known. Ever since the construction of the Canadian Pacific railway, attempts have been made from time to time to mine the pegmatite dykes in and near the Eau Claire area, but, although some feldspar has been mined, no appreciable muscovite was produced. Lace in 1941, J. Purdy and H. MacDonald discovered a dyke containing large crystals of high-grade muscovite from which they are reported to have sold $700 worth of mica. They recorded claims 35974 and 35975 in December, 1941, and claim 36095 in May, 1942.

Jan 1, 1943

By T. Patching

"A GLANCE BACK AT what has happened in the past is often a useful guide to the future, although it should be used mainly to provide a sense of direction rather than a map that must be followed. As a preamble to discussing some of the questions posed by the organizing committee it may be appropriate to briefly review the distribution and careers of the graduates of our Department since the first degree in mining engineering was awarded in 1916. An attempt has been made to keep a record of the locations and careers of the Department's 540 graduates in mining and metallurgical engineering. Almost all of those who graduated before 1930 have now retired, but a very large proportion held positions as senior executives prior to retirement. A major proportion of those who graduated before 1950 are now in what might be considered senior management positions. Those who have 10 to 20 years of experience are generally in work of senior engineering responsibility or in supervisory or junior management ranks, while those who graduated in the last ten years appear to be generally in staff engineering or junior supervisory positions. This classification is admittedly imprecise because it is difficult to determine from a job description whether duties should be considered of an engineering or management nature - a distinction between the two terms is often over-emphasized. Nevertheless, the trend from technical engineering to management responsibilities with seniority and years of experience is clear in the careers that we have been able to follow."

Jan 1, 1972

By C. Bernier

This paper deals with three major problems associated with mining operations during the winter. These are the maintenance of the cooling systems of diesel engines, the high incidence of hydraulic dump failures on packaging machines, and the build-up of frozen fines on wet-ore conveyor belts.

Jan 1, 1966

By Richard E. Barrett

SOME YEARS AGO I was associated with a mining operation which, because of its isolated location, burned wood for heating purposes. Year after year the tractors and tucks hauled the cordwood in from the edge of the ever-growing clearing. Each year the cartage costs became greater. The degree to which transportation distances affect the economics of fuels obviously varies with many factors, but the main criterion is the amount of heat a unit weight of the fuel will produce. For in-stance, wood is limited in most cases to a haulage distance of a few miles. Coal can be shipped hundreds of miles, whereas petroleum and gas ?can be transported thousands of miles. The world is now on the brink of having a new fuel -uranium. It has the virtue of being so concentrated that transportation costs can, for all practical purposes, be disregarded.

Jan 1, 1958

By E. Thune, F. Stålesen, E. O. Stensholt, O. M. Dotterud, E. E. Henriksen, P. O. Ramsdal

"The development and commercial operation of the Falconbridge chlorine leach process have been described in papers in 1985 and 1987. Since this time, various process improvements have been implemented and the capacity of the Kristiansand refinery has been increased to 85 000 t/y Ni, 40 0000 t/y Cu and 4500 t/y Co. The focus has been on continuous improvements in productivity, the use of energy and other costs. Several environmental issues have also been eliminated or reduced since 1987. IntroductionThe first nickel refining operation in Kristiansand, Norway, started in 1910 based upon raw materials from Norwegian mines. In 1929, Falconbridge Nickel mines purchased the refinery to acquire information and the patent rights to the Hybinette refining process that was practised at the small Kristiansand refinery. Falconbridge ownership has now, for more than 70 years, provided a strong base regarding raw material supply, financial resources and technical support for further expansions and major technical improvements at the refinery.The main concepts of the new chlorine leach process were developed in the laboratories from 1966 to 1969 and the process was piloted from 1970 to 1972. The main stages in the commercial plant were started in the 1975 to 1981 period. After 1981, there have been a number of process modifications, plant expansions and improvements to operating practices. The developments up to 1988 have been described in previous publications (Stensholt et al., 1986, 1988).This paper presents an overview of the process and how it is practised at Falconbridge Nikkelverk AS (FNA) today and describes some of the main changes that have been implemented since 1988. During this time, the nickel capacity has been expanded from 54 000 t/y to 85 000 t/y and the cobalt capacity from 2000 t/y to 4500 t/y. The paper describes how these expansions were achieved together with continuous improvements in operating efficiency and also gives an overview of the main environmental concerns at the refinery."

Jan 1, 2001

By F. M. Waldie

THE 2,538-foot belt conveyor recently installed underground at the Sullivan mine hoists ore from the 3,350-foot level to the 3,900-foot or main haulage level, a vertical distance of 680 feet. The design and planning of development work, under the direction of Mr. R. H. Stewart, Consulting Engineer, was begun in the spring of 1941. Development work was started in July of that year from the 3,350-foot level, and headings were started on the 3,650-foot and 3,900-foot levels later in the same year. It was the intention at that time to keep three headings going on development work necessary for the installation of the system: two on the conveyor incline, and one on the 3,900-foot level. This programme was modified in 1942 when there was some doubt whether the material for construction could be obtained. This problem of supply was eventually solved and the development work was pushed to completion in December, 1943. Construction was started in December, 1943, "'under the supervision of Mr. G. H. McKay, Superintendent of Construction and? Maintenance, and was completed in November, 1944.

Jan 1, 1945

DOME MINES, Limited, is a gold producer situated in the Porcupine area of Ontario, 500 miles north of Toronto. During the year 1960, '71 4,600 tons of ore were milled, yielding gold bullion valued at $6,025,370. Prior to conversion to natural gas, an average of 3,200 tons of coal was consumed annually, one third of which was obtained from Canadian sources with the remainder coming from the United States. Due to the distances involved, the freight charges increased the pithead cost by as much as ISO per cent. Steam is generated at a central boiler plant and used for timber treatment, plant heating and process steam. Until August, 1960, steam was supplied during the winter months by two water tube coal-fired boilers, each rated at 200 boiler horsepower at 100 per cent output. Steam requirement was as high as 150 per cent of boiler rating in the colder periods. The summer load was

Jan 1, 1962

By Serge Perreault

Le cuivre est un métal fascinant qui joue un rôle essentiel dans le développement des différentes civilisations depuis 7000 ans. Le cuivre est aussi un métal polyvalent et essentiel qui est très présent dans notre vie quotidienne. L’un des premiers métaux utilisés par les humains, il est un élément chimique qui se trouve à l’état natif, ce qui est rare pour les métaux. Il apparaît principalement dans des minéraux, notamment sous forme de sulfures, en raison de son caractère chalcophile (c’est-à-dire son attraction pour l’élément soufre). Le cuivre se trouve dans la croûte terrestre sous forme de minéraux de cuivre, tels que dans les sulfures dont la chalcopyrite, la bornite, la covellite et la chalcocite. Il est également présent sous sa forme native ou dans des minéraux oxydés comme la cuprite et dans des carbonates hydratés, comme la malachite et l’azurite. La formation de gisements de minerai de cuivre implique des processus géologiques complexes, notamment l’activité hydrothermale, les intrusions magmatiques et l’altération des roches. Les gisements de minerai de cuivre se trouvent dans divers types d’environnements géologiques, dont les gisements porphyriques, les gisements de cuivre encaissés dans des roches sédimentaires, les gisements de type skarn, les gisements de sulfures massifs volcanogènes, les gisements magmatiques de type nickel-cuivre, les gisements de cuivre oxydé, et d’autres [1].

May 2, 2024

By MAX VOS

Lithium is the lightest and electrochemically most reactive of all metals. Renewed interest in lithium coincides with research in lithium batteries and power generation by atomic fusion. Ontario lithium resources are contained in spodumene pegmatites that can form where medium- to high-grade metamorphic volcanic-sedimentary formations are intruded by pegmatite and porphyritic granitic rocks. Spodumene pegmatites occur in at least twelve locales throughout northern Ontario, all of which are in the Superior Province of the Precambrian Shield. Tantalum, cesium, rubidium, beryllium, niobium and tin also were noted with lithium in spodumene pegmatites. Considerable potential remains for discovery of additional lithium and rare-element pegmatites in northern Ontario.

Jan 1, 1984

By Grant S. Diamond

THE BIBLIOGRAPHY on the use of static electricity in mineral beneficiation consists largely of patents. Some references are found in mineral textbooks, but very little data on flow-sheets of commercial installations are known to the writer. As a matter of fact there have been relatively few successful commercial applications of importance. Johnson prepared and published a Table showing the polarity and static field intensity requirements of many minerals. There have been reports of successful beneficiation of rutile, zir-con, coal, potassium chloride, and phosphate rock. Otherwise, the field of success has been very limited. This may be due to three reasons: first, the mining industry has been averse to dry processes, be-cause of dust nuisances in dry crushing; second, the electrostatic processes used in the past apparently developed no substantial economic advantages; and third, because flotation or other . methods have proven successful on many minerals, the industry has not felt the need for a radically different process. In the feldspar industry there was ?an attempt at electrostatic beneficiation about twenty years ago which was based on the use of fluoride fuming of the pegmatite head feed, in order to make the mineral reactive in a static field. This process was originally said to be successful, but was discontinued because of corrosion damage to machinery. Another effort by use of a chemical additive such as an or-ganic hydroxyl compound has also been attempted. Neither of these processes is known to be in use today.

Jan 1, 1957

By Rafic Moubarac

FRP (Fiberglass Reinforced Polyester) equipment has been used in different and several applications during metals processing and extraction, and the hydrometallurgical process. Case histories of such equipment will be shown of major projects worldwide.

Jan 1, 2015

By Jean-Marc Simard, Richard Genest

"La mine Agnico-Eagle, localisée près de Joutel, a été découverte en 1962 par le forage d'anomalies électromagnétiques. Exploitée à partir de 1974, elle a déjà produit près de 30 tonnes d’or à partir de 2 puits, le puits Eagle et le puits Telbel, distants de 1,3 km.Le gisement est situé entre le sommet du complexe volcanique de Joutel, à dominante felsique, et la base de l'ensemble sédimentaire de la rivière Harricana. Ces deux unités ont une extension régionale; elles sont orientées NW-SE avec une polarité NE et des pendages subverticaux. Une faille majeure, la faille Harricana, passe de façon subconcordante au contact de ces deux ensembles.La minéralisation aurifère, de 2 à 5 m d’épaisseur moyenne, est liée a une zone carbonatée, comprise entre des tufs felsiques, argilites et sédiments chimiques (éponte inferieure) et des argilites carbonatées (éponte supérieure). Le minerai est constitué habituellement de 20% de fine pyrite disséminée. L’or est en fines particules associées directement à ces grains de pyrite de texture cataclastique.Deux modelés ont été for mules jusqu' a présent pour expliquer la genèse du gisement: une thèse syngenetique (Barnett et a/.1982) et une thèse épigénétique (Wyman et al. 1986). Cette dernière apparalt comme la plus probable du fait de la présence de la minéralisation dans les zones cisaillées a carbonates secondaires et pyrite cataclastique."

Jan 1, 1990

By H. G. Harper, R. C. Hart

"The Mississagi quartzite is the basal formation of the Quirke Lake trough. As it is traced around the rim, a gradual change in dip is observed, as follows:Northwest corner 50 degrees south.Algom Quirke mine 34 degrees south.Quirke Lake 25 degrees south.Whiskey Lake 22 degrees west.Pecors Lake 25 degrees north.Algom Nordic mine 18 degrees north.Elliot Lake 11 degrees north.Pistol Lake 5-7 degrees west.Thus the apparent synclinal axis is a curving east-west line lying closer to the north limb than to the south. The axis appears to plunge west at about 5 degrees.The Huronian sediments lie on a basement of granites, gabbros, and volcanics. Diamond drill evidence indicates that this basement has a surface of peneplanation, and that the areas of soft basic rock have a smoother topography than the granite. For the most part the orebodies at the Quirke and Nordic mines overlie a basement of soft basic rock.The Mississagi formation is the host rock of the deposits, and its primary structures are suggestive of the conditions under which the conglomerate beds were deposited. Cross-bedding is common, although normal bedding varies from thick to thin to essentially lacking. Grain gradation is not common. Where coarse and fine grains occur together, the coarse tend to be more rounded than the fine. These features are characteristic of shallow-water deposits, laid down above the lower limit of wave action. Therefore, the quartz-pebble conglomerates probably represent ancient water courses, bays, beaches, and bars.The causes governing the creation of the trough can only be conjectured, but there is evidence that both subsidence and compressive stresses played active roles. Drag-folds in argillite beds near Whiskey Lake indicate compressive stress. On the other hand, gentle crumpling in thin-bedded limestones on Quirke Lake is probably due to pre-induration slumping and folding. If strong compression had been widespread within the trough, one would expect drag-folding and shearing of the incompetent beds to be more general. Two large-scale, fold-like structures were mapped by Collins, but their axes do not parallel the trough axis, and they are therefore not related to the major structure."

Jan 1, 1949

By Henry Lepp

Introduction A shaft sinking operation carried out at the Viking Yellowknife mine in the spring of 1947 presents certain features, especially as regards speed of sinking and low cost, that may be of interest to Institute members, and especially to those who are not familiar with conditions and costs in the Northwest Territories. After collaring, the inclined, two-compartment shaft was sunk 130 feet by four miners in twenty-eight days at a direct cost of only $53.19 per foot. All things considered, this is a remarkable performance, even if it does not actually establish a record. The property is at Morris lake, some forty-five miles north of Yellowknife. Formerly owned by Athona Mines (1937), Limited, it was acquired by the then newly incorporated Viking Yellowknife Gold Mines, Limited, in 1947. Surface work and diamond drilling in 1946 disclosed a number of veins and masses of quartz in a sill of diorite which lies conformably within sedimentary rocks. The sill strikes N.30°E. and dips at 70° to 85° southeast, and has a mean width of 40 feet over its explored length of 3,000 feet . Both the quartz and the diorite carry gold and are mineralized with pyrrhotite and lesser amounts of galena, sphalerite, chalcopyrite, and arsenopyrite. Of thirty-five holes drilled in the mineralized zone, the core from twenty showed visible gold. Sampling of drill cores indicated several ore shoots in the north and central parts of the sill. Assays, however, were somewhat erratic, possibly due to the fairly widespread presence of visible gold, and it was decided that the deposit could best be explored by underground sampling. Accordingly, late in 1946, plans were laid for the sinking of a shaft.

Jan 1, 1948

By O. F. Carter

"Coniaurum Mines, Limited, hold nineteen claims in Tisdale township, in the Porcupine district, adjoining the McIntyre mine on the east. They extend for over a mile along the strike of the Hollinger-McIntyre 'break'. The property has been explored extensively along the ore zone both laterally and vertically. Workings have been carried to a depth of 5,500 feet, and nearly 50 miles of lateral workings (drifting and cross-cutting) have been driven to date in development and in gaining access to the orebodies.Production started at the Coniaurum in June 1928 and has continued without interruption. To the end of 1946 the plant has treated 2,695,725 tons of ore, yielding gold having a value of $21,989,918.The Coniaurum is controlled by Ventures Limited of Toronto. Mr. John Redington, who has guided all operations since work began on the property in 1922, is Managing Director.GENERAL GEOLOGYAge and Types of RocksKeweenawan- Quartz diabase dykes.Algoman - Quartz porphyry intrusive; the veins are probably late Algoman.Keewatin - Lava flows.Brief Description of Rock Types.Diabase DykesTwo quartz diabase dykes traverse the property in a north-south direction, cutting all formations, including veins.Porphyry IntrusivePetrographically all porphyries in the Coniaurum are of the usual Porcupine type- quartz-feldspar with alteration advanced in most instances to the stage where the feldspars are completely dissolved, leaving a wellsheared carbonate and sericite matrix with embedded rounded quartz 'eyes'. Alteration is most extensive in the smaller bodies and in the narrow protuberances from the larger masses; the cores of the larger masses are generally much fresher, with more or less well defined feldspar phenocrysts."

Jan 1, 1954

By J P. Bolduc, P. E. Pelletier

Preceded by brief general considerations such as the development of the mining industry in. the Province of Quebec, the choice of plant location, the types of problems studied etc., the paper gives a complete description of this new research and treatment center for metallic, non-metallic and asbestos ores. Facilities for carrying out operations in the three sections of the plant -the sampling section, the ore treatment section and the asbestos section -are fully discussed as well as laboratory facilities for (a) the preliminary testing of ores prior to pilot plant treatment and (b) the grading and testing of asbestos fibre. AT THE beginning of the century, the annual value of the mineral production of the Province of Quebec stood at the $2,500,000 level. Twenty-five years later, it was just under $24,000,000. In 1950, half a century later, it was slightly in excess of $200,000,000. But in 1959, in the span of only nine years, it

Jan 1, 1962

By Gaston Gendreau

CETTE PRÉSENTATION traitera des différentes phases des opérations de la mine du Mont-Wright depuis ses débuts jusqu'à présent. A une brève description de la géologie du gisement, suivra un exposé des méthodes d'exploitation de la mine et du genre d'équipement utilize.

Jan 1, 1977

By Phillip Mackey, Elmira Moosavi-Khoonsari

L'industrie du cuivre traverse une période passionnante, marquée par une forte demande, de bons prix et l'ouverture de nouvelles grandes installations. L'année 2022 a battu des records de production de cuivre, ce qui laisse entrevoir un potentiel de croissance supplémentaire. De grands projets sont en cours, comme la technologie Double Flash à Manyar, en Indonésie, qui peut produire plus de 500 000 tonnes de cuivre par an. À Munda, en Inde, on a construit la plus grande usine de cuivre du monde, qui produit plus de 1 000 000 tonnes de cuivre par an en combinant deux phases. De plus, l’installation de cellules de flottation de dernière génération au Mexique, au Chili et dans d'autres pays témoignent de la volonté de l'entreprise d'utiliser les technologies les plus récentes [1]. L'importance du cuivre dans la transition énergétique est évidente, l'accent étant mis à la fois sur la croissance et sur la protection de l'environnement. Cela se traduit par le développement d'usines de premier ordre dédiées aux pratiques durables.

May 2, 2024

By Garnet T. Page

"ABSTRACTThese societies •can help in such aspects of a vocation.al guidance program in secondary schools as: provide vocational and technical information, and assist with vocational exploration, such .as plant visits, films, etc. -as .an aid to the student in making a self-inventory. Evidence is increasing that employers' needs for engineers and scientists will not be adequately met in the future. Therefore, the E.I.C., C.I.M., .and C.I:C. recently revised and extended the activities of the Canadian Counselling Committee on Engineering and Science. This co-•operative .action is to be integrated with the educational system, nationally .and locally, and with provincial associations •of engineers and other groups interested in the provision of vocational information in engineering and science.DEFINITIONTHE scientific treatment of any subject requires consistent use of carefully defined terms. The National Vocational Guidance Association of the United States studied the problem of the definition of vocational guidance for .about 16 years, and in 1937 finally arrived at:""Vocational guidance is the pro-cess of assisting the individual to choose an occupation, prepare for it, enter upon and progress in it. It is concerned primarily with helping individuals make decisions and choices involved in planning a future and building a career -decisions and choices necessary in effecting satisfactory vocational adjustment.""RANGEAs a school enterprise, vocational guidance begins at that point in the individual's life when he finds it necessary to make choices that have a definite significance for his future vocation."

Jan 1, 1952