Search Documents

By A. P. LeBis

This article attempts to relate the concept of utility to the risk involved when only a small number of projects (compared to their probability of occurrence) are accessible to a firm and to quantify utility when other financial and physical parameters are known.

Jan 1, 1978

By G. V. Sirianni, G. E. Viens, R. A. Campbell, G. N. Banks, R. L. Sachdeva

"A combined shaft-electric furnace for the smelting of ores and the melting of metallized iron pellets is being developed. The materials are preheated, and in some cases pre-reduced, in the shaft before being transferred to the electric furnace, where melting or smelting is completed. It has been demonstrated that this combination of equipment will enable much of the relatively expensive electrical energy to be replaced by cheaper energy in the form of oil or natural gas, and preliminary experiments indicate that the total energy requirements for a melting or smelting operation are significantly reduced. Projections based on results obtained from the preliminary experiments indicate that further improvements will be possible when certain modifications to the equipment are completed."

Jan 1, 1968

By R. A. Halet

"The Malartic Gold Fields mine is a good example of the association of ore deposits with a major fault zone. It also exemplifies the control exerted by the physical and chemical character of the host rocks on the localization of orebodies.The mine is in Fourniere and Dubuisson townships, Abitibi county. It is 6 miles east of the town of Malartic, 9n the main highway and railway from Noranda to Val d'Or.The discovery of the mine is due largely to the enterprise of the late J. P. Norrie, who organized the present Company in 1935. The ground is entirely covered by overburden, but Mr. Norrie believed that the extension of the Cadillac-Malartic 'break', the principal ore-bearing structure of the district, would be found on this group of claims. This belief was supported by the discovery of gold-bearing float in the area, and was confirmed by a dip-needle survey and a few pilot diamond drill holes that showed that the favourable Malartic greenstone band passes through the centre of the property.In this way the most favourable area for prospecting was narrowed to a zone 2 ½ miles long by ½ mile wide underlain' by greenstone. The remainder of the property is underlain by sedimentary rocks, which, from experience elsewhere in the camp, were not considered as promising. However, as the entire surface is covered by deep overburden, the location of orebodies even within this more or less restricted area could be accomplished only by a long campaign of diamond drilling. Systematic diamond drilling began in 1936.The contacts of the greenstone band were considered to be the most promising places to begin the work, and the early drilling was concentrated on the south contact, because the orebody of the East Malartic mine, 4 miles to the west, had been discovered on this structure and it was reasonable to hope for a repetition of these conditions. Although the south contact was very thoroughly explored, with a certain amount of encouragement, the work did not prove the existence of deposits of ore grade, and attention was shifted to the north contact zone of the greenstone band. In this locality much more promising results were obtained, and a number of good orebodies were outlined."

Jan 1, 1954

By W. A. Jones

"The Ross mine, a subsidiary operation of Hollinger Consolidated Gold Mines, Limited, is near the north end of lot 1, con. II, Hislop tp., Ontario. The property comprises the north half of lot 1, con. II, and the south onethird of lot 1, con. III. It is readily reached by a good motor road from the village of Ramore, 7 1/2 miles to the southeast on the Ontario Northland railway. The mine is being developed to a depth of 1,500 feet, and the current daily production rate is approximately 300 tons. From the inception of operations in March 1935 until December 31, 1945, 692,000 tons of ore, with a total value of $5,762,685, was milled . The silver to gold ratio of 1.48 to 1 is unusually high for Ontario gold mines.TYPE OF 0REBODIES AND MINERALIZATIONThe orebodies consist of lens-shaped and pipe-like stringer lodes and tabular vein zones composed of parallel quartz stringers. The host rocks are steeply inclined eruptive breccias and tuffs, striking N.70°W., intruded by very small stocks of red syenite. The orebodies appear to be spatially related to an intricate system of fault planes. Hydrothermal alteration is widespread and is not zonally related to individual quartz stringers. The wall-rocks contain abundant fine-grained pyrite, but gold is confined to the quartz stringers.RELATIONSHIP TO REGIONAL STRUCTURELack of outcrops has prevented the detailed mapping of the Keewatin complex in the vicinity of the Ross mine with the degree of success that has been achieved in the Porcupine area.A northwesterly trending belt of slates and greywackes, bounded by faults, forms the central part of a broad anticlinal arch about 3 1/2 miles north of the Ross shaft. Lava flows forming the south flank of the structure face south toward the mine. If the sediments are to be tentatively correlated with the large areas of Keewatin slates and greywackes of the Porcupine area, it must be assumed that they are younger than the lava flows and that they have been down-faulted."

Jan 1, 1954

By M. M. C Jiménez, J. A. S Ténorio

For the recovery of valuable materials and for the protection of environment, recycling process of printed circuit board is an important subject of study. Moreover, the popularization of the computers and its technological evolution has generated a large number of waste electrical and electronic equipment. This paper presents a study of synergistic solvent extraction of copper, nickel and zinc from a sulfuric leaching liquor of printed circuit boards (PCB’s). The percent extraction of copper, nickel and zinc from dilute aqueous sulfate media besides synergistic effect of mixture of the .extractants Cyanex 272 and D2EHPA have been studied. Furthermore, different conditions such as temperature, pH of the feed solution have been examined. The results suggest that the synergistic effect of the .extractants mixture enhance the extraction efficiency of nickel.

Jan 1, 2014

By F. Mackay, S. A. B. da Fontoura

"The theoretical solution for a viscoelastic well was presented by Gnirk and Johnson in 1964. From this an exercise was executed to validate the numerical simulation of a cemented salt well. The exercise comprised the geomechanical behavior through time of a cemented salt well, this was achieved using a finite element commercial software. This simulation showed the accuracy of the theoretical solution for viscoelastic materials such as salt rock. The theoretical solution presented elastic and viscoelastic analytic equations for the tangential and radial stresses. The equations for the elastic material (casing and cement) and for the viscoelastic material (salt rock) are presented here: Where equations 1a & 1b are the radial and tangential stresses of the elastic material; equations 2a & 2b are the radial and tangential stresses of the viscoelastic material; and a, r and b are the geometrical parameters explained in Figure 1. These equations are function of Pb, a stress time dependent factor that comes from the Burgers model of viscoelasticity. This is well explained in Gnirk and Johnson (1964) and for the sake of simplicity is not disclosed here. Po is the stress at section A-A’ dependent of the depth h."

Jan 1, 2015

By J. Bakos

Solar Hydrogen Energy Corporation (SHEC Labs) recently constructed a pilot-plant to demonstrate a Dry Fuel Hydrogen Generation System that is powered primarily by sunlight focusing-mirrors. The pilot-plant consists of: A Solar Mirror Array and Advanced Solar Concentrator and Shutter System; and two thermo-catalytic reactors to convert Methane, Carbon Dioxide, and Water into Hydrogen. Results from the pilot study show that Solar Hydrogen generation is feasible and cost-competitive with traditional Hydrogen production. More than 95% of Hydrogen commercially produced today is by the Steam Methane Reformation (SMR) of natural gas, a process that liberates Carbon Dioxide to the atmosphere. The SMR process provides a net energy loss of 30 to 35% when converting from Methane to Hydrogen. Solar Hydrogen production provides a 14% net energy gain when converting Methane into Hydrogen since the energy used to drive the process is from the sun. The environmental benefits of generating Hydrogen using renewable energy include significant greenhouse gas and criteria air contaminant reductions.

Jan 1, 2005

By Fernando Canales

In the last decade a great dealt of attention has been paid to the chemistry of polynuclear gold derivatives with a central heteroatom, not only from the experimental and structural but also from the theoretical standpoint (1). Interesting hypercoordinated species of the type [C(AuPR3)5]+, [C(AuPR3)6]2+, [N(AuPR3)5]2+, [P(AuPR3)5]2+ and [P(AuPR3)6]3+ have been described (2), apart from other complexes with more conventional stoichiometry, and all have in common the presence of gold-gold interactions of ca. 3 Å. Usually, the chemistry of the first row elements of the p-block is known to follow classical rules of bonding, and only in cases of extreme electron-deficiency has the traditional electron count to be reconsidered to account for special types of molecular or solid state structures. Many of these heteroatomcentered complexes are electron-deficient and the gold-gold interactions provide a significant contribution to their stability. The attraction between these closed-shell systems has recently captured the attention in inorganic and organometallic chemistry (1). P. Pyykkö has summarized the available theoretical and experimental evidence of intra- and inter-molecular interactions between heavy metal atoms, such as Au(I) (3). In general, when heavy metals are involved in such interaction, the closed-shell attractions are of metallophilic or van der Waals type, as has been found for d8, d10 coinage-metals, and d10s2 centers. Experimental evidence for the aurophilic Au(I)???Au(I) attraction is available from crystallography, NMR and Raman spectroscopies, and optical spectroscopic measurements of the interaction strength (4). It is manifested in molecular conformations with relatively close Au???Au interactions of ca. 3 Å, whose strength has been estimated at ca. 25-50 kJ/mol (5). These attractions are weaker than most covalent or ionic bonds, but stronger than other van der Waals bonds and comparable in strength to typical hydrogen bonds. The phenomenon cannot be satisfactorily explained by classical theories such as hybridization (3). From a theoretical point of view, the attractions close to equilibrium distances are caused by dispersive interactions together with relativistic effects (6). The attractive contributions are dominated by pair-excitations from the heavy metal, such as gold, strengthened by relativistic effects. In all the cases where there are inter- or intramolecular metal-metal attractions, the correlation effects are essential; if they are omitted, at the Hartree-Fock (HF) level, repulsive interactions are obtained (6). Hence, it is necessary to use at least second-order Møller-Plesset level (MP2) methods for the dispersive forces, which are included in the electronic correlation effects (7).

Oct 1, 2003

Current AG and SAG mill circuits have continued the trend to larger, fewer mills. These large mills place a significant additional load on the discharge systems and it has become imperative that the designs of these mill discharge systems are evaluated carefully to ensure maximum efficiency and have the capacity to be able to handle the increased mill discharge volumes. The current generation of multiphysics modeling tools allow a detailed analysis of AG and SAG mill discharge performance. The combination of Discrete Element Method modeling and Computational Fluid Dynamics allows the designer to model in detail all aspects of a mill discharge performance. This includes a detailed description of the build-up of solids and slurry in a mill discharge, the recycle of material back into the mill through the grates, the relative wear rates and the occurrence of overloading at the pinch points. These tools allow intelligent decisions to be made regarding the type of discharge arrangement, pan lifter geometry, and discharge cone design, so as to ensure that the discharge is capable of handling the duties required for a specific installation. This paper details the current state of the art in these modeling tools, and provides an overview of some recent applications.

Jan 1, 2012

By Dogan Paktunc, Larry J. Hulbert, Robert C. Carne, D. Conrad Gregoire

A thin layer of stratiform Ni-Zn-PGE sulfide mineralization of sedimentary-diagenetic origin was deposited during the Middle to Upper Devonian in the euxinic "Nick basin". The mineralized unit (=3 cm thick), which seems to have been developed over the entire sedimentary basin of > 80 km2, consists of pyrite, vaesite (NiSz), and sphalerite. The average grade of the mineralization is about 5.30/0 Ni, 0.73% Zn, =770 ppb (pGE+Au), and up to 61 ppm Re. Anomalous Se, As, Mo, P, Ba and U are present. A minimum of 0.90 x 106 tonnes of Ni were deposited in the basin (based on a bed thickness of 3 cm) during the Devonian. The unique metal association, extensive lateral distribution, persistent metal grade, mineralogical makeup, and stratigraphic control demonstrate that this is a new deposit type and a new geological environment for Ni and PGE + Au. The sulfide layer occurs at the base of a Phosphatic Chert Member which is underlain by a distinctive marker unit consisting of concretionary limestone structures. The limestone spheroids may represent a vent-specific carbonate facies developed adjacent to faults that emanated nutrientrich hydrothermal discharges just prior to the main mineralizing event. The suite of elements associated with the Nick mineralization suggests that the ore-forming metals were originally bound to organic matter derived from decaying marine organisms. Discharge of hot brines bearing organic matter-bound metals took place along numerous conduits within basin faults that are now manifest as bitumen veins. Our syndiagenetic model proposes that these fluids were discharged laterally from the conduits into the unconsolidated bottom sediment (ooze). The introduction of this metalliferous fluid, rich in organic matter, stimulated biological activity and bacterial reduction of its contained 804 to sulfide. Hot, dense, laterally migrating hydrothermal fluid precipitated thin sulfide-rich larninae within bottom sediment. Published thermodynamic studies suggest that the diagnostic vaesitepyrite assemblage crystallized at approximately 138°C. The 034S values range from -14.7 0/00 to -10.00/00 and are up to 340/00 lighter than locally surrounding sulfides and age-equivalent mineralized strata elsewhere in the Selwyn Basin. The Ol3C values of calcite in the footwall of the mineralized unit (- 12 0/00 to -6 0/00) are isotopically much lighter than regional values. The lighter isotopic character is attributed to the hydrothermal discharge of fluids enriched in organic compounds. Although geochemical profiles of the lower Earn Group sediments that host the Nick mineralization reveal that these black shales are not distinctive, the unusual Ni, Zn, PGE, U, Ba, and P elemental associations and their anomalous concentrations in stream sediments can be used to explore for this deposit type.

Jan 1, 1992

By J. Paquin, P. Doiron, G. Proulx, P. Champoux

After nine years on a 36 hour schedule and two programs of creeping, the Alcoa Deschambault Potroom of faced the necessity of changing its organization for many reasons: the anodes butts were too small, the anode schedule was unbalanced, the iron content in the metal trends had increased, the metal tapping volume did not convene with crucible capacity and the liquid measurement task was delayed by tapping activities. A kaizen activity inspired the Potroom department to improve the organization. A team of 15 people including the process engineer, the process technician, team supervisors and Potroom operators developed a scenario, which would permit flexibility to creep pots if energy is available and an increase of added value production.This paper will describe the systematic approach, the communication method, the trials, the changes, and our success, along with the problems experienced by the team during the adaptation of Alcoa Deschambault Potroom organization over a 20 month period. Aluminium 2006 45th Annual Conference of Metallurgists ofCIM Montreal, Quebec, Canada Edited by

Jan 1, 2006

By Liang Zhen, Jian-Tang Jiang, Guo-Ai Li, Xiao-Ya Wang

"Deformation behavior of 2A97 aluminum alloy containing coarse secondary phases was studied using uniaxial hot compression (HC, 340–490°C, 0.4001–1 s-1). The flow stress could be described by a Zener-Hollomon parameter in hyperbolic sine function with the hot deformation activation energy of 237 kJ/mol. Based on the experimental data and dynamic materials model, processing maps were generated to demonstrate the hot workability of the alloy. The coarse secondary phases experienced dissolution by varying degree under different deformation temperature, which producing different effects on the microstructure evolution. When deformed at relatively low temperatures, a mass of fine grains shaped up in the original grains and grain boundaries, and the dominating deformation mechanism was believed to be dynamic recrystallization. As the deformation temperature rising to 490°C, most secondary phases disappeared and few recrystallized grains were observed, indicating that the secondary phases dissolved sufficiently along with dynamic recovery occurred during the hot deformation. Particle stimulated nucleation related to the coarse secondary phases was believed to promote the recrystallization and the recrystallization behavior was sensitive to deformation temperature.INTRODUCTION Al-Li alloys has received much attention as new promising structural materials in the aircraft and aerospace industries, due to their lower density, higher elastic modulus and improved fatigue crack growth resistance in comparison with the conventional commercial aluminum alloys (Ou Ling, 2015). 2A97 alloy is one of the 3rd generation Al-Li alloys targeting at comprehensive improvement of aviation aluminum alloy and applications for wing spars and ribs to other internal structures for transport aircraft. Al-Li alloys are usually formed by hot deformation, either by rolling or extruding. The deformation behavior and resulted microstructure evolution during the forming process mainly dominates the formability of the alloy and the serving performances as well. Therefore, the deformation behavior and microstructure evolution at elevated temperature need be made clear for optimizing the hot processing parameters and controlling microstructure evolution."

Jan 1, 2018

By Sergio Romo, Gerardo Fuentes, Adriana Garcés

Refractory ores with gold entrapped in a sulfide matrix, must be processed in a first stage with chemical or physical treatment in order to liberate the gold for a subsequent step with cyanide. The goal of this research was to compare the refractory behavior of a gold concentrate treated using two pretreatment methods: pressure oxidation and fine grinding. Gold concentrate from Viacha Mining in Bolivia, assaying 50.11 gpt, with a P80 of 131 ?m was used. The concentrate contains arsenopyrite and pyrite as main sulphides in the matrix. A preliminary test with cyanide resulted only 13.5% of gold extraction with 4 hours of stirred leaching. Using an autoclave oxidation with sulphuric acid and 12 bar oxygen pressure at 220°C pretreatment, the cyanide gold extraction increased to 69.0% in 4 hours. When material was ground in a pulverizer, producing a P80 of 20 ?m and the product directly cyanided, stirred leaching gave a gold extraction of 65% in 4 hours. For both techniques, the effect of temperature, sulfur produced in autoclave oxidation, optimization of the cyanide and the nature of residues were also studied.

Jan 1, 2014

By W. G. Worcester

IN the presentation of this paper to the Institute, three objects are in the mind of the writer: first, to set forth the close relation which, of necessity, exists between ceramics and the industrial minerals; second, to clarify the apparently hazy understanding which many have of ceramics in general; and lastly, of equal or even more importance, to stimulate a greater interest in the industrial minerals, especially in those used and required by the ceramic industries. While Canada is now producing in large quantities a fairly wide variety of the ceramic industrial minerals, there are some which are not known to occur in the Dominion. Hence it is to be desired that our geologists, prospectors, and others, while on field work, should be on the look out for commercial deposits of such minerals as diaspore, bauxite, ucts of a value in excess of $600,000,000, a figure which places ceramics as kyanite, massive topaz, and sillimanite. A find of any of these in quantity would prove of very great importance and value to the country as a whole. At this point it seems desirable to introduce formally the word ceramic or the plural of it, ceramics. In doing so it may be stated that the origin of the word dates far back in history in that it was derived in part from the Greek word Keramos, 'a potter' or 'pottery', which in turn has been traced back to an older Sanskrit root meaning 'to burn' or 'burned stuff', having reference, no doubt, to burned pottery or other clay wares; and the word was so used until near the close of the last century, when the world's first schools of ceramic engineering were established in the United States. The use of the term ceramics was then expanded to cover a much larger field the entire field of the silicate industries and products. At one time it was suggested by a limited number of ceramists that the term 'ceramic engineering' be changed to 'silicate engineering'. This proposal, however, gained little support and was soon abandoned.

Jan 1, 1945

By Kevin J. Melong

"Redpath Canada Limited and joint venture partner Thyssen Mining and Construction Canada have recently completed the sinking of the Scissors Creek service in Saskatchewan through its joint owned company, Associated Mining Construction (AMC). The Scissors Creek service shaft was sunk at Nutrien’s Rocanville mine. The following paper outlines the shaft sinking plant and the methodology related to sinking and shaft lining. KEYWORDS Hydraulic shaft jumbo, Hydraulic shaft mucker, Potash shaft sinking, Shaft lining, Sinking galloway INTRODUCTION The sinking and lining of shafts at mines to access mineral deposits has always been one of the great mining challenges for owners, engineers and contractors. Over the course of history in Canadian mining, the sinking of potash shafts through the notorious Blairmore formation of Saskatchewan has proved to be some of the most challenging shaft sinking projects on record. There is no doubt that today’s shaft sinking business demands the utmost in safety performance while delivering projects within schedule and budget. Given these requisites, Redpath and TMCC (executed under the joint venture company, Associated Mining Construction or AMC), were taxed with developing the shaft sinking system to deliver this program in the safest and cost effective manner, with due regard to schedule and quality. Traditionally the potash shafts sunk in Saskatchewan involved a significant level of manual labour, owing to the methodology of excavation by means of chipping the frozen shaft sections with hand held pneumatic machines, and manually placing tubbing segments or steel liners of the shaft lining system. Most certainly, the AMC team wanted to make a step change from those earlier sinking programs and develop systems for sinking this potash shaft that removed the high level of manual work, thus making this project inherently safer, while endeavoring to sink more efficiently. With that in mind, the team embarked on a design program to improve its overall shaft sinking systems without the requirement for excessive capital and methodology flexibility to adapt to potential changing conditions expected to be encountered during shaft sinking. This was especially important should the new approach be met with less than expected success, and retrofitting of the system was required. The concepts were developed to provide for a much improved work environment, while easing the manual labour burden on the workers with innovative equipment and approach to the work."

Jan 1, 2019

By Parviz N. Farsangi, Ferri P. Hassani, Allen G. Hayward

"Kidd Creek Mines places approximately 10 000 tonnes of consolidated rockfill (CRF) daily. Consolidated rockfill comprises sized aggregate mixed with different ratios and amounts of binders. Consolidated rockfill is employed to simplify subsequent pillar recovery and provide improved passive/active ground support.The consolidated rockfill is designed to sustain not only the gravitational loading of the overlaying fill material, but also to some extent the dynamic loading applied during blasting of the adjacent stopes and/or pillars. This paper describes the steps taken to optimize the pre-sent fill system at Kidd Creek Mines.The emphasis is on four areas which have high saving potential: lower cost alternative binders, structural design, quality control measures, in-situ testing techniques for back analysis. A consolidated rockfill design optimization chart was developed from these investigations."

Jan 1, 1996

"Some of the tools developed for the processing of nickel laterite ore by resin-in-pulp (RIP) may be applicable to the remediation of metalliferous mine drainage (MMD). In both cases, recovery of metal value and production of a stable waste stream appropriate for long term storage is desired. MMD typically has the additional challenge of management of toxic low-value metals. Seen in this light, innovations in RIP reactor configuration, selective elution strategies and novel synthetic ion exchange resins become useful tools for taking on the MMD challenge in a way that maximizes both environmental and economic benefit. INTRODUCTIONAcid mine drainage (AMD) is a common problem in any country with significant past mining activity. When sulphide containing minerals, tailings or slag are exposed to water, oxygen and sulphur oxidizing bacteria, AMD will result. Abundant and reactive iron sulphide minerals leach first, providing acidity and the ferrous/ferric couple that can enhance the oxidation kinetics of other minerals. If this runoff contacts encounters acid consuming carbonates or silicates, the acidity may be neutralized, but certain heavy metals remain in solution and can continue to be an environmental hazard (Gray, 1997). For this reason, the remainder of this paper will refer to the broader term metalliferous mine drainage (MMD) rather than acid mine drainage. In either case, such drainage, containing high heavy metal concentrations and often significant acidity, is toxic to aquatic life and can lead to significant damage to ecosystems and to public watercourses. MMD is a problem most commonly associated with now defunct sulphide mineral mines, but similarly toxic streams can result from many types of waste, such as poorly stabilized leach tailings, slag heaps, and coal flotation tailings (Johnson and Hallberg, 2005; Lee et al., 2002; Sainz et al., 2002; Schüring et al., 1997). In any case, the management and remediation of MMD is an important ongoing problem for the resource industry, particularly for the many mines in Canada closed before the advent of more stringent environmental standards. MMD remediation represents a significant long term expense for the resource industry. Multi-disciplinary efforts to understand and mitigate this problem range from creation of artificial wetlands (Poulin and Lawrence, 1996; Sheoran and Sheoran, 2006) to sophisticated biochemical reactors and precipitation processes (Hatami, 2010). Certain remediation technologies such as ion exchange offer methods to make a saleable product by recovering valuable dissolved metals. This paper will show how these technologies can help defray the cost of remediation, and offer potential to turn a dangerous waste stream into a useful product."

Jan 1, 2012

By M. Clotilde Apua, A. F. Mulaba-Bafubiandi

"The efficiency of hydrochloric acid (HCl) leaching of gold from low grade gold-bearing material has been investigated in the presence of sodium hypochlorite (NaOCl) to produce in situ chlorine gas which is an oxidizing agent able to oxidize gold metal to its soluble forms. The effect of concentrations of HCl, NaOCl, and mixtures of HCl + NaOCl was sought. Iron and potassium present in the feed were leached and consumed all the HCl. Gold found as inclusion in pyrite was not exposed to the lixiviant. Therefore, leaching of gold from low grade gold-bearing material in aqueous chlorine solution is not an effective process for now.INTRODUCTIONHydrometallurgy of gold is commonly based on cyanide leaching solution. Due to the environmental concerns related to cyanidation and mercury processes, and inefficiency of cyanide gold leaching to dissolve refractory ores, sustainable alternative lixiviant systems, capable of generating gold (I) and gold (III) complexes must be studied. Amongst non-cyanide gold lixiviants there is the chloride/chlorine system (Hilson and Monhemius, 2006; Senanayake, 2004; Pilsniak and Trochimczuck, 2007; Wang et al., 2007; Reeves et al., 1999; Khodadad et al., 2008).In practice, the most oxidizing agents utilized for the leaching of gold as chloride, are chlorine (Cl2) or hypochlorite (HOCl) which are either generated in situ by suitable reaction or added in solution (Adamson, 1972). The dissolution of gold concentrate using hydrochloric acid, sodium chloride and sodium hypochlorite (Cl-/HOCl system) were studied (Puvada and Murthy, 2006). The effect of NaOCl and NaCl concentrations were also investigated. The leaching was performed under the following conditions; time: 4h, solid–liquid ratio = 1:4, at room temperature. It was found that the increase of the NaOCl concentration from 25 to 75 g/L did not have any meaningful effect on the recovery of gold which was about 30% (experimental conditions; S/L ratio = 1:4, NaCl concentration: 25 g/L, HCl concentration: 0.35 M). It was also found that from 25 g/L to 200 g/L NaCl, the recovery of gold rose from 30% to 40% (experimental conditions; S/L ratio: 1:4, NaOCl concentration: 25 g/L, HCl concentration: 0.35 M)."

Jan 1, 2012

By Douglas C. Fraser

A DIGHEM survey was flown in the Belford-Montcalm Township area of Ontario in November 1975. This 600-linemile survey resulted in the detection of 134 EM anomalies. The Montcalm Township copper-nickel discovery yielded a single-line anomaly having a conductance of 154 mhos. This anomaly was highly visible because (a) it had the highest conductance in the survey area, (b) it correlated with a 175-gamma thumbprint-shaped magnetic anomaly and (c) it was isolated from long conductive bands. The deposit is a copper-nickel pyrrhotite body which occurs in gabbro and strikes north-south, parallel to the flight lines. The DIGHEM survey was flown north-south, because the exploration program was primarily concerned with locating copper-zinc sulphides in the east-west-striking felsic volcanics. The flight line passed close to the deposit and yielded a 9-ppm anomaly on the chart record. The computer analysis showed that a deposit of exceptionally high conductance (154 mhos) caused the relatively weak (9 ppm) anomaly. The ground follow-up program of magnetics and EM led quickly to the discovery drill hole, which penetrated the orebody in September 1976. Subsequent geophysical surveys consisted of horizontal-loop EM, pulse EM, magnetic and induced polarization surveys over an area of about 8 claims. In addition, a detailed DIGHEM" airborne survey was flown at a line spacing of 100 m to evaluate the entire property of 620 claims. This detailed survey yielded EM conductor maps and contour maps of resistivity, magnetics and enhanced magnetics.

Jan 1, 1978

By D. Van Tonder

ABSTRACT The comparative economics of ion exchange and direct precipitation have been analyzed by developing indicative CAPEX/OPEX models for typical alkaline leach uranium circuits. An agitated tank ore leach application is considered, comparing resin-in-pulp and direct precipitation as recovery options. Capital and operating cost estimates are derived from rates and factors used in recent studies and projects. The analysis showed the main economic drivers to be the ore grade and resin loading. The resin loading is impacted by the prevalence of competing ions, especially chloride. At resin-in-pulp solution chloride concentrations below 3 g/L and uranium grade below 640 g/t U3O8, resin-in-pulp is more economical, whereas at chloride concentrations above 3 g/L, direct precipitation is more economical.

Jan 1, 2012