Search Documents

By M. A. Hararah, T. Neesse, M. G. Farghaly, G. Proellss, P. Kaniut, W. Rubarth

ABSTRACT: This paper presents two new options for hydrocyclone control. Volume split control using a control valve in the overflow is applied for the stabilization of separation results at changing feed conditions. Controlled water injection to the conical part of the cyclone leads to the reduction of fine particles in the underflow. Hydrocyclone monitoring in both cases is performed by optical sensors that indicate the spray angle of the underflow. Applications in mineral processing for desliming, classification in closed-circuit grinding, and dewatering are demonstrated.

Jan 1, 2011

By C. Kim

The integration of three-dimensional (3D) data with infrared thermography has received much attention for its potential use as input data for building energy simulations. Therefore, researchers have proposed methods to integrate 3D data with infrared thermography obtained by different sensors. These studies show the potential of the integration of 3D data and infrared thermography using various systems. However, these studies have ignored property aspects of infrared thermography, such as the low resolution of infrared thermography and external environmental influences. Thus, their proposed methods to integrate 3D data and infrared thermography are inadequate because these problems can affect the resulting building energy simulation. This research proposes a framework that integrates infrared thermography and 3D data while accounting for the resolution and shadow effect of infrared thermography. The proposed framework consists of three steps. In the resolution enhancement step, bi-cubic interpolation is proposed. In thermal data correction from the shadow effect, the shadow area is detected from the visible image, and then the shadow effect is removed from the registered infrared thermography. Finally, enhanced infrared thermography is mapped to the 3D data obtained by a laser scanner. The performance of the proposed framework was evaluated using test images obtained from a building in operation. The experimental results show that the proposed framework provides a 3D thermal model that is useful and accurate in simulating building energy. It is expected that the 3D thermal model can be used for accurate energy simulation of existing buildings. In addition, the proposed framework can be applied in defect detection for buildings. Furthermore, this novel approach enhances infrared thermography using visible images.

Aug 1, 2013

By Antoine Fournier, Karen St. Seymour

"Responding to market developments, interest in locating deposits of wollastonite has grown significantly. The many occurrences in the Grenville marbles of Quebec can be grouped into disseminated type and discordant vein-type deposits. Disseminated-type wollastonite occurrences have the disadvantages of lower grade, the need for more elaborate mineral separation, and failure to meet ""long grain"" technical specifications. Vein-type deposits have better grades and technical characteristics; exploration should be focussed on these and in the contact-metamorphic aureoles of fluid-rich intrusions. SOMMAIREEn réactions aux nouveaux de bouches, l'interet pour les gîtes de wollastonite a crû de façon marquée. Les nombreux indices sis dans la province de Grenville au Québec peuvent être regroupes en deux catégories soit: les indices dissémines et les indices en veines discordantes. Les indices dissémines ont le désavantage d'être moins enrichis, de requérir une séparation minéralogique plus complexe, et leur wollastonite ne possède pas le degré d'acicularité voulu. Les indices en veines sont plus enrichis en plus de rencontrer les critêres techniques; les efforts d'exploration devraient se porter vers ce type de gites et aussi, sur les auréoles métamorphiques de contact d’intrusions riches en fluides."

Jan 1, 1992

By J. R. Fisher

"Uranium may be leached to some extent in situ from the Blind River conglomerate uranium ores by using the products of bacterial activity from the bacterium Thio-bacillus ferrooxidans his paper describes some of the laboratory techniques used to investigate the characteristics of the bacteria, and to utilize their properties in uranium leaching. The application of some of the laboratory results underground at the Milliken mine of Rio Algom Mines Limited are de-scribed, along with the method of uranium recovery from the mine waters."

Jan 1, 1966

By Adam J. Szladow

"INTRODUCTIONThe low calorific value and the high moisture and ash contents of run-of-mine (r.o.rn.) lignite limits the utilization of Saskatchewan lignites to thermal power plants in Saskatchewan, Manitoba and western Ontario. On the other hand, the low sulphur content and the low mining cost make lignites potentially attractive for new coal markets, if suitable processes can be found for upgrading. Economic upgrading to a higher quality fuel would make lignites more acceptable for industrial and utility boilers.This paper presents a summary of the process engineering evaluation of coal upgrading technologies conducted in support of a study of selected lignite upgrading processes. The summary presents the relative advantages and offers specific comments on the application of coal upgrading technologies for lignites. ResourcesLignite comprises the largest fossil fuel energy deposits in Saskatchewan. The total resources of immediate and future interest exceed 27 billion tonnes. The measured and indicated lignite resources of immediate interest are large enough to last for over 200 years at the current production rate of about 10 million tonnes per year (Table 1).Saskatchewan lignitedeposits are present in three different geologic formations: (I) the Ravenscrag Formation of Paleocene Age in southern Saskatchewan; (2) the Swan River Formation of Lower Cretaceous Age in central north Saskatchewan; and (3) the Judith River Formation of Upper Cretaceous Age in central west Saskatchewan. The deposits in the Swan River and Judith River Formation are not currently of economic interest.The Ravenscrag deposits are confmed to four lignite basins, namely: the Estevan, the Willow Bunch, the Wood Mountain and the Cypress basin (Fig. 1). The estimated resources of immediate interest in the four basins are over 7 billion tonnes (Table I). These resources include lignite seams at least 1.5 m thick, at depths of less than 45 m.The average quality of lignite varies relatively little between the four basins considering the distance between deposits (Table 2). There is, however, a progressive increase in moisture and ash content, and a decrease in calorific value and carbon content as one moves westward from the Estevan to Wood Mountain and Cypress basins. The Estevan area deposits are of higher rank despite the fact that they are stratigraphically younger than the Willow Bunch deposits (Cameron and Marconi, 1979).In upgrading lignite to a higher quality fuel, it is important to know not only the average proximate and ultimate analysis (Table 2) but also other lignite characteristics influencing the product quality . For example, Figure 2 shows the effect of lignite HIC ratio on the product equilibrium moisture for hydrothermal treatment of lignite. It is apparent that lignites with a higher HIC ratio, or high liptinite content yield much better quality product for the same hydrotreatment conditions. Other examples of lignite characteristics which are important in upgrading include distribution of sulphur forms and mineral matter, maceral composition and degree of surface oxidation."

Jan 1, 1989

By R. L. Bruening, L. Navarro, Izatt. S. R., R. Adiga, R. M. Izatt, N. E. Izatt, A. Sharma, N. R. Patel, B. V. Rao

Bismuth is a notorious contaminant in the electrolytic refining of Cu that can cause cathodes to fail to meet ASTM International standards and not be suitable for use in Cu rod and other downstream products. Bismuth can significantly decrease electrical conductivity, decrease the mechanical strength of the annealed wire, retard recrystallization, and sometimes induce hot shortness during the hot rolling process in the production of rod. As a result, the control of Bi in the refinery tankhouse must be carefully managed. This paper describes how SuperLig® Molecular Recognition Technology (MRT) is being used for Bi removal at the Birla Copper Dahej Copper refinery. The operation of the SuperLig® MRT Bi removal plant is described and data on Bi removal efficiency are presented. INTRODUCTION Hindalco’s Cu division, Birla Copper, operates one of the largest Cu refineries in the world at Dahej, Gujarat; India. The main feed for this refinery is produced at the company’s smelter. Due to its massive production capacity, this operation mainly relies on imported Cu concentrates resulting in a variety of metals being carried out as impurities in the Cu anodes because pyrometallurgical technologies alone are not enough to remove them to the extent required. Metal impurities found in Cu ores include Fe, Zn, As, Pb, Bi, and Sb. During electrorefining, less noble metals dissolve in the electrolyte gradually increasing their concentrations creating the need for electrolyte control mechanisms that remove these impurities with varying degrees of success (Wang, 2004; Navarro et al., 2013.) Bismuth is one of the most significant impurities in a Cu refinery because it has the lowest ASTM product specification. This situation is critical because the Bi potential is very close to that of Cu making it possible to plate in the Cu cathode directly. Also, Bi can precipitate at high concentrations causing floating slimes and reduction of current efficiency (Ballinas, San Miguel, Munoz, & Gyves, 2003). Production of high purity cathodes from feed stock containing a diverse range of metal impurities becomes a major challenge in the refining of Cu (Izatt et al., 2015). In this work, the purification strategy followed by Birla Copper for the removal of Bi using a separation process based on MRT is presented, outlining the loading and stripping performance of SuperLig®83 and the benefits of using MRT over other lower selectivity methods where hazardous materials are produced instead of high purity products.

Jan 1, 2019

By Jared Onyirimba, Jim Viellenave, Hal Demuth, Dale Verran, Chad Sorba, Errol Lawrence, David Bronkhorst

As outlined within the Denison Mines Corp’s (“Denison”) Pre-Feasibility Study ("PFS") completed in late 2018, additional work is required to increase confidence and reduce risk associated with the application of the In-Situ Recovery (“ISR”) mining method at the Phoenix deposit, located on the Wheeler River Uranium Project (“Wheeler River” or the “Project”) in northern Saskatchewan. The successful application of ISR in any geological environment largely hinges on three fundamental requirements, 1) permeability (of the deposit), 2) containment (of the mining solution) and 3) leachability (of the mineralization). Denison has designed several staged technical programs to progressively reduce risk associated with these requirements as the Company advances the Project toward a Feasibility Study (“FS”) and Environmental Impact Assessment (“EIA”). This paper will discuss the scope and results of certain technical programs being undertaken as the Company aims to develop the first ISR mining operation in the Athabasca Basin.

Jan 1, 2020

By W. J. Wright

Summary Statement The following notes on the geology of the Grand Lake coalfield are intended to be introductory to a second paper being read at this meeting, which paper will describe the earlier and the more modern mining methods. The coal industry of the Grand Lake coalfield is centred chiefly within a three-mile radius of Minto, but minor operations are dotted over an area of approximately 50 square miles extending easterly to the vicinity of Chipman and Coal Creek (see Figure 1). The coal comes from one seam of Pennsylvanian age. The seam varies in thickness from 16 to 30 inches and lies almost horizontal at depths of 0 to 125 feet. It has been mined and prospected over an area of approximately 150 square miles, but in a portion of this area the commercial possibilities have been destroyed by erosion. The industry is the oldest of its kind in North America, but it did not at tract particular publicity until about 1914. Since that date, mining methods have improved and the output has rapidly increased until, in 1934, it amounted to 271,335 long tons, and furnished employment for about 1,000 men (1). Approximately 73 percent of this amount was produced by the Minto Coal Company, the Miramichi Lumber Company, the Avon Coal Company, and Welton and Henderson, and 25 per cent by the Rothwell Coal Company, Harvey Welton Limited, G. H. King, the Reade Construction Company, and the Newcastle Coal Company. The remainder was produced by J. W. Carter, G. D. Crossman, T. H. Swift, C. S. Yeamans, and several other small operators. The coal is won by underground mining, except in the case of the Reade Construction Company, and a minor operation by Ashfield and Pieton, who have employed open stripping. It is mined only as required to fill definite orders, and is loaded directly into cars for shipment. In 1934, the larger mines did not operate full time, and the production could easily have been increased if markets had been available. The coal is sold in four grades: screened or lump, run of mine, slack, and stripping. The chief market is with the railways and commercial plants, with a fair amount for domestic purposes.

Jan 1, 1935

By S. Hosseinpour

Chromate conversion coatings (CCCs) are usually applied to these alloys to enhance their resistance to localized corrosion and to improve paint adhesion. The special properties of these coatings such as their low electrical contact resistance (ECR) make them suitable for satellites. This study is aimed to develop advanced CCCs with the proper appearance, morphologies and surface roughness and to evaluate their role on the ECR and thermo physical properties on hardened aluminium alloy of Alclad-7075-T6. Coating characterization was performed by means of scanning electron microscope (SEM) and atomic force microscope (AFM). ECR of coatings were measured by special laboratory designed instrument and a and c were measured by Emissometer and Reflectometer respectively. In addition, corrosion performance of the CCC-coated alloys was determined by 168 hr exposing to salt-spray testing in accordance with ASTM-B117. The results of accomplished experiments on the developed CCCs in this study have been agreeable concerning available acceptability criteria for satellite surfaces.

Jan 1, 2007

By R L. Cheesman

An extensive Precambrian iron-formation lies about 2,000 ft. beneath post-Precambrian rocks in the Fort a Ia Corne Forest Reserve, south of Choiceland, Saskatchewan. The geology, deduced from limited drill results and from some geophysical observations, indicates that the deposit is a characteristic magnetite iron-formation, not uncommon in the exposed Precambrian of Saskatchewan, but also shows certain interesting features of faulting and pre-Paleozoic weathering which have given rise to a pre-served detrital deposit of hematite. The body is of ore grade and of sizeable proportions. T HIS paper is presented in order to set forth the interesting geological features of a Precambrian iron deposit located beneath the cover rocks of the Great Plains region and to comment upon the methods of discovery and interpretation of the nature of the body. The Choiceland iron deposit is located in the Fort a Ia Corne Provincial Forest Reserve, some 15 miles south of the town of Choiceland, Saskatchewan. Choiceland is

Jan 1, 1964

By D. J. Lloyd

"Bending is involved in the forming of many sheet parts and it is important to understand the phenomena involved. In this paper the basic equations describing bending on a global scale are compared with strain measurements of bent sheet. The development of strain on a local, microstructural scale is also investigated, as is the general aspects of plasticity and the failure process. It is shown that the global equations can be used to estimate the strains involved and the local strains can be attributed to various aspects of the plasticity. The bendability can be related to the fracture strain of the sheet and the ability of a sheet alloy to accommodate the necessary bending to form the part can be assessed.INTRODUCTION The ability of a sheet alloy to undergo bending without failure is an important capability in the forming of many parts and it is useful to be able to assess the bendability of an alloy during its development. The basic mechanics of bending were developed in the 1950s (Lubhan & Sachs, 1950; Hoffman & Sachs, 1953). When a sheet is bent the upper bend surface is in tension, the lower surface in compression and at some point within the sheet there is a plane of zero strain which is referred to as the neutral axis. For sheet exhibiting limited plasticity the neutral axis is static and occurs at the mid-point of the sheet thickness but for sheet exhibiting extensive plasticity the neutral axis progresses deeper in to the sheet as bending progresses. This results in two expressions for the maximum strain at the upper bend surface depending on the motion of the neutral axis. For Al alloys such as AA6111, AA6016 and the like extensive plasticity occurs and the neutral axis is expected to move during bending. However, very few studies have examined how the neutral axis motion and the strains develop, compared with the mechanics analysis. Geist and Parker (1984) used hardness measurements to investigate neutral axis motion but these experiments did not have the resolution necessary to compare the results with experiment but did indicate neutral axis motion. To understand the nature of plasticity and failure during bending it is important to know the extent of neutral axis motion, the scale of strain gradients developed through the sheet and the maximum strains occurring at the bend surface, finally comparing experimental results with the theoretical predictions. The influence of microstructure on the evolution of strain and failure can then be considered in the context of these parameters. Recently, bending in some automotive Al alloys has been reported mainly from the microstructural perspective (Lloyd, 2000, Lloyd et al., 2002, Mattei et al., 2013) and FEM studies have also investigated the development of plasticity under bending, demonstrating the tendency for strain localization (Becker, 1992, Shi et al., 2014)."

Jan 1, 2018

By Binbin Luo, Northeastern University, Chuanyao Sun, Jie Liu, Yimin Zhu, Yanjun Li

"A series of new type collectors a-bromo-saturated fatty acids, CH3(CH2)5CHBrCOOH (a-BHA), CH3(CH2)7CHBrCOOH (a-BDA), CH3(CH2)9CHBrCOOH (a-BLA), CH3(CH2)11CHBrCOOH (a-BMA) were synthesized from saturated fatty acids and bromine by solvent-free method (Hell-Volhard-Zelinski reaction) in laboratory. The micro-flotation tests of quartz mineral were conducted at a relatively low temperature of 15 °C. The adsorption mechanism of such collectors on quartz mineral surface were established by zeta potential measurements, in conjunction with the results of quartz micro-flotation tests. The flotation results showed that the collecting ability is in the order of a-BMA > a-BLA > a-BDA > a-BHA for the flotation of quartz mineral, which also demonstrating that the a-bromo-saturated fatty acids (a-BFAs) are new selective collectors for reverse flotation to remove quartz mineral from iron ores at a relatively low temperature.INTRODUCTIONThe requirement of higher pulp temperature to maintain the activity of fatty acid anionic collectors which have been widely applied in technological process of iron ores reverse flotation lead to a great deal of energy consumption.The purpose of this paper is to synthesize a new modified collector with carbon chains from eight to fourteen atoms, with strong electronegativity bromine atom introduced into a-carbon position to improve the activity and solubility of the reagent so that it can be adopted at a comparatively low pulp temperature. The collecting performances of these new collectors on quartz surface were studied, and the structure - properties were discussed in light of zeta potential measurements and quantum chemistry calculations."

Jan 1, 2016

By R. Burnette

Gold has been mined from a variety of deposit types that range in age from Archaean to Recent. The large variability in the geological settings of the gold deposits implies transport and concentration of gold by magnetic, hydrothermal and sedimentary processes. The factors that control the concentration of gold at certain sites and the grade estimation thereof remain major topics of debate. Due to the complex nature of the Witwatersrand Basin a mineralogical study, including mineralogical, petrographic and geochemical investigation was launched on TauTona Mine in order to characterize the various reef facies. The aim of the investigation was to determine if a correlation could be found between macroscopic characteristics of the reef, hanging wall and footwall, and the microscopic nature of the ore (especially gold grade). Petrograpgic and mineralogical results indicate that a correlation exist between gold, detrital and hydrothermal sulphides, uraninite, carbon, detrital heavyminerals and phyllosilicates. No correlation exist between gold and Mg, Fe or S. It appears that clast supported reef is of higher wade than matrix supported, but more work is suggested. No correlation exists between reef thickness and grade. The reef samples had the lowest phyllosilicate content compared to the hanging wall and footwall samples with pyrophyllite the most dominant. All of the correlations diagrams showed significant scatter and suggests a multi- factorial mineralization model. Gold distribution is also controlled by sedimentary features and thus it is not possible to select a single model for the formation and distribution of gold. It is evident that both sedimentary and hydrothermal factors influenced the mineralization and gold distribution on TauTona mine. It is thus essential that all related theories be incorporated in the development of a grade prediction model.

Jan 1, 2011

By Robert B. Parsons

"On February 15, 1984 Finance Minister Lalonde presented to Parliament a budget heavily flavoured with the current consultative mood of the Government. Notably absent from the budget was the typically long list of tax changes of immediate effect. Instead, the bulk of the budget papers consisted of a wide variety of white papers on significant topics that would have a far reaching impact on the future of all Canadians.This month. Tax Notes examines the highlights of Mr. Lalonde's budget.IntroductionThe mining industry need not feel slighted in Finance Minister Lalonde's budget of February 15, 1984: the budget offered very little that would have an immediate impact of significance on any sector of the economy. Apart from some welcome announcements for the oil and gas industry to postpone the implementation of certain negative tax changes, the budget was surprisingly scant in terms of definitive tax proposals.While massive revisions in the rules relating to pensions, small businesses, commodity taxation and profit-sharing were brought forward, many of these proposals are set out in White Papers or other documents to be implemented into legislation only after further consultation. Canadians will accordingly have to wait for such promised benefits as increased RRSP and other pension contribution limits."

Jan 1, 1984

By J. G. Conaway, P. G. Killeen

"Gamma-ray spectral logging, a useful technique for uranium exploration and evaluation, has generally been underutilized by the Canadian mining industry. Provided that the technique is properly applied, it is capable of yielding reliable quantitative information regarding the distribution of uranium and other radioelements along the borehole under most conditions.In practice. there are numerous factors which potentially can degrade the quality of the log and thus any quantitative interpretation based on it. Fortunately, the appropriate choice of logging equipment and technique can avoid many such problems, and corrections can be applied to the data to compensate for most of the others."

Jan 1, 1980

By N. D. Wineinger, J. Jodouin

"An Independent Electricity System Operator Industrial Accelerator Program (IESO IAP) case study was completed for a mine in Ontario, Canada by SRK Consulting, Inc. The purpose of the study was to analyze the ventilation system to determine whether and which system improvements could reduce the overall electrical power demand of the mine. Financial incentives are offered by the IESO IAP grant program to help cover the capital costs of these improvements. This study included the completion of a full mine ventilation survey as well as measurement of a full suite of electrical parameters of the surface and underground ventilation fans. After these measurements, a base ventilation model was created and established as the system baseline. Changes to the ventilation system were modeled, and their effects on the power demand were projected. The results of the study showed that several improvements were possible which may significantly improve the efficiency of the ventilation system and reduce mine electricity demand.INTRODUCTIONIn 2017, a ventilation study was conducted in accordance with the Independent Electricity System Operator Industrial Accelerator Program (IESO IAP) at a mine in Ontario, Canada. The IESO IAP is designed to assist eligible transmission-connected Canadian companies operating in Ontario to fast track capital investment in major energy conservation projects. The program will provide financial incentives to encourage investment in innovative process changes and equipment retrofits to reduce electricity consumption on the provincial system and to help companies become more competitive by positively impacting their bottom line. There are now four initiatives under the Industrial Accelerator Program:1. Retrofit2. Process & Systems, including Small Capital Projects3. High Performance New Construction4. Energy Managers – a new initiative under the Industrial Accelerator ProgramWithin the program, companies may propose energy saving changes to their current systems where applicable and appropriate. Companies may then be awarded funding to implement the proposed changes. The program allows partial financial compensation to implement certain energy saving changes that would otherwise not be considered due to high capital costs. For larger projects, such as underground mine ventilation systems, a detailed engineering study must be submitted. This study must detail each energy saving change or measure, its savings, and calculate the financial incentives using the IESO IAP Payment Structure. The payment structure for a project is an amount equal to the lowest of the following (Independent Electricity System Operator, 2015):"

Jan 1, 2019

By E. O. Reinbold, J. H. Johnson, D. E. Keski-Hynnila

A field laboratory for use in monitoring underground mine air quality has been developed and proven in underground service. The laboratory includes two separate monitoring systems and data analysis computer programs. One is the Mine Air Monitoring Laboratory (MAML). This is an enclosed trailer-mounted laboratory capable of monitoring CO2, CO, NO, NO2 particulate matter, S02, NH3, temperature and air velocity in the mine drift. The MAML can be up to 1000 feet away from the area being monitored. The second system is the vehicle data system, mounted on the load-haul-dump (LHD) vehicle, which monitors engine speed, engine fuel rack position, exhaust gas temperature, ambient temperature, vehicle speed, CO2 concentration near the operators' breathing zone and the mode of operation of the vehicle. The two computer data analysis programs and the two field instrument systems comprise a complete Mine Air Quality Laboratory (MAQL) for underground pollutant studies. Data from the systems have been used for studying vehicle duty cycles, ventilation systems, exhaust after-treatment devices, vehicle exhaust system design and portable instrumentation. Descriptions of the laboratory are presented along with a summary of some of the experiments performed. The capabilities of the lab are discussed, along with future potential uses.

Jan 1, 1981

By E. Allen

Quebec Cartier Mining Company operates approximately two hundred and fifty pieces of equipment in a climate with a temperature that has averaged 27.5°F during the last seven years. The use of special-purpose lubricants, fuels, antifreeze, rubber compounds, and alloy steels have reduced the cold-weather hazards. In some areas, high-cost cold-weather protective heating devices are being eliminated with experience.

Jan 1, 1966

By P. Rocque, S. Talebi

Although the measurement of blast vibration close to the blasthole is critical to the understanding of rock fragmentation mechanisms and blast damage in the rock masses, limited experience for such monitoring exists. Because much higher vibration amplitude and frequency ranges are expected in rock masses close to an explosive charge as compared to far field vibrations, different problems from those for the far field monitoring must be considered for near field blast vibration monitoring. Currently, guidelines for design of the near field blast monitoring systems do not exist. This paper describes the development of an integrated technique for vibration monitoring close to a blast hole, including selection and installation of transducers, design of a monitoring system and signal recording. A densified cement was designed for grouting accelerometers in order to match p-wave impedance between the rock and grout. The monitoring technique described has proven suitable for blast vibration monitoring within 2 m to 15 m of a blast hole having loading conditions similar to production blasts.

Jan 1, 1993

By R. W. Zeindler, D. A. Fawcett

"A summary is presented of the report completed by the Coal Mining Research Centre in 1980. This report was of a cross-pit conveyor system applied as an auxiliary mining complement to the major stripping unit, a dragline. The purpose of the CMRC report was to evaluate selective mining and replacement of the upper horizons of the strata as an aid in reclamation. These strata were the topsoil, subsoil and glacial till.Past utilization of cross-pit conveyor systems and related engineering studies were assessed. The parameters of the study were based on the mining and geological conditions of the Alberta prairie coal mines. The principal excavator for stripping was a dragline. Excavation of the upper horizons was done by a bucket-wheel excavator discharging onto the crosspit conveyor. Alternative equipment applications were economically compared. Four cases or geological sections were evaluated in detail. The economics of the alternative mining systems for each of the cases were determined. In all instances, the most economical solution was a tandem system utilizing a dragline with a bucket-wheel excavator/ cross-pit conveyor system."

Jan 1, 1981