Search Documents

By Alex McEachern

MINING LEADS WAY TO PROSPERITY THE year 1937 will stand out in the history of mining and metal products in Canada as one of which we shall always be proud. The combined contribution of these industries played a large part in leading Canada back to prosperous conditions after years of stress and strain that left their mark upon business the world over. A review of general industry shows a marked improvement over recent years. The upward trend continued un-abated most of the year and not a few of the industries had all they could do to supply the demands. A fact that should be appreciated in a year of wheat failure over an extensive area of the Prairie Provinces is the shifting of the basis of Canadian prosperity from agriculture to that of mining and the use of metals. To the great demand for minerals of all kinds, our mines have well responded and many new high levels were reached. This reflects great credit upon the men who direct the activities of the Canadian Mining Industry. Possessed by a spirit which refused to accept defeat in 1931-1932, they began to increase the efficiency of their departments, explored all channels hitherto untried, and won through to a crowning success. Who among them dreamed that their country's extremity would be their Alex. McEachern opportunity, and that through their united efforts our young nation would be enabled to hold that high position she has attained in world affairs?

Jan 1, 1938

By Nessetech Consulting, L. A. Cisternas, E. D. Galvez, S. H. Kuan, L. H. Saw

"In Malaysia, there were two rare earths processing plants namely Asian Rare Earth (ARE) and the Malaysian Rare Earth Corporation Plant (MAREC) in Perak, which were operated until 1992 and were subsequently closed due to problems pertaining to disposal of large amount of radioactive waste. Recently, Lynas Advanced Materials Plant (LAMP) has become one of the largest rare earths processing plant in the world producing rare earth elements (REE) in Gebeng, Pahang. The primary raw material is lanthanide concentrate (LC) which is imported from Mount Weld mine in Australia and shipped to Malaysia. LC is produced from lanthanide ore after mining and mineral processing. The ore has a lower impact than Bayan Obo, Mountain Pass and adsorbed clay deposits, given the small footprint of the mine itself and the remoteness of the location. The type of ore being mined (rare earth phosphates: carbonatite, monazite) may have higher thorium content than bastnasite ore from the Chinese or American mines but still far below radiation concerns. This paper was written to review the processing flowsheet at the Lynas Advanced Materials Plant (LAMP), the environmental impact associated with the processing of the said ores and the sustainability of the operation.INTRODUCTIONRare earth minerals are one of a set of 17 minerals or chemical elements which consists of yttrium and scandium, as well as the 15 lanthanide elements (lanthanum, cerium, praseodymium, neodymium, promethium, europium, gadolinium, terbium, dysprosium, holmium, erbium, thulium, ytterbium, and lutetium). Despite their importance, rare earth minerals rarely exist in economically viable concentrations and they are usually difficult to extract. Rare-earth minerals create strong magnets when added to magnetic elements such as iron, and are useful for the production of electronics systems as well as electric cars. They are also used extensively in automotive catalytic converters, fluid cracking catalysts in petroleum refining, wind turbines, phosphors in colour televisions and flat panel screens, displays for mobile phones and laptops, rechargeable batteries, and various medical devices. The elements are typically split into two subgroups: the cerium sub-group of ‘‘Light’’ rare earth elements (LREEs) which includes La to Eu and the yttrium sub-group of ‘‘Heavy’’ rare earth elements (HREEs) which include the remaining lanthanide elements, Gd to Lu, including yttrium (Gupta and Krishnamurthy, 1992; Jordens et al., 2013; Trifonov, 1963). Scandium, however, when it is classified as a rare earth element, is not included in either the LREE or HREE classifications (Gupta and Krishnamurthy, 1992; Jordens et al, 2013). Half of the world’s 110 million tons of reserves exist in China while other sizable deposits are found in Russia, United States, Brazil, India, Australia, Canada, and Greenland. The countries known to be actively mining REE are China, Russia, India, Brazil and Malaysia (Hao et al., 2015). Among these countries, China has the largest REE production, accounting for more than 93% of global supply (Yap, 2015). The critical metal report (Moss et al. 2011) listed 14 economically vital raw materials that are prone to supply disruption and concluded that supply disruption would threaten the goal for cleaner transport and sustainable energy since rare earth metals are used in products using green technology, such as hybrid/electric vehicles, carbon capture systems, wind power generation, low-energy lighting, and energy efficient flat-screen displays."

Jan 1, 2016

By Lloyd H. Yeomans

"This paper will cover recent developments in conveyor applications with specific reference to capacities, bell speeds and distances. It will also discuss certain unique arrangements of horizontal, curved and loop belt systems. In addition, the recent changes in safety factors resulting from new conveyor construction methods will be reviewed.IntroductionConveyor belt systems are currently undergoing dramatic changes. Their use is being extended to providing a viable means for the transportation of bulk material over longer and longer distances.In this paper, a brief account of the historical development' of the belt is outlined, demonstrating how conveyor technology has adapted to changing market demands.Today, energy and environmental requirements are providing what may even be greater challenges. The ability of the belt conveyor to transport material and meet those requirements, places it in the position of replacing many conventional means of bulk material transportation.The paper also outlines some of the progress which has been recently made in this regard and includes a broad approach to the subject of belt design and application.Recent design developments have greatly extended the potential of conveyor belt systems to include applications thought impossible just a few years ago.Graphically illustrating the potential of this new technology IS a belting system currently operating in New Caledonia. Built in 1970, the system has an incredible centre distance of 43,000 ft, or about eight miles.Not to be outdone, the British Coal Board is currently constructing a belt system with a centre distance of 49,000 ft and a speed of 1,650 feet-per-minute. This system is expected to be completed in 1986.These innovative advances contrast dramatically to the conveyor belt's beginnings in the early industrial revolution. Oliver Evans, writing in the 1795 edition of 'Miller's Guide' defined the conveyor belt as a ""broad endless strap of thin pliant leather or canvas, revolving on two pulleys in a case or trough.""Obviously, the conveyor belt has come a long way since those early days."

Jan 1, 1983

By Wm. L. Giachino

"Over the last 10 years, C-1-L has played a significant role in the major advances that have taken place in blasting technology, among them the following: development and introduction of capsensitive slurries; development of bulk slurry systems both for underground and open-pit operations; development of the TOE-DET and ANODET systems of delay blasting;introduction of the NONEL system of initiation;development of the Vertical Crater Retreat (VCR) system of mining.This paper identifies areasin which we foresee further developments in blasting technology over the next 10 years and outlines how and to what extent C-1-L will become involved."

Jan 1, 1980

By William W. Shilts

"In carrying out a geotechnical survey of a proposed gas pipeline route from the Arctic Islands south to Longlac, Ontario, the Polar Gas Consortium contracted the drilling of several hundred 2- to 2D-m-deep boreholes in drift and bedrock. Samples from these holes were made available to the Geological Survey of Canada, where they were subjected to stratigraphic and trace-element geochemical analyses. The geochemical characteristics of the clay and sand-sized heavy mineral fractions of till samples from these boreholes have been summarized in a series of geochemical profiles.From the proposed pipeline terminus at Longlac northward to the vicinity of God's River in Manitoba, tills contain significant amounts of Paleozoic carbonate rocks and Proterozoic sedimentary rocks derived from the Hudson Bay basin and lowlands. Within this section, two sites were enriched in base metals, indicating the possibility of local mineralization of possible economic interest.From God's River northward to Seal River, Manitoba, no evidence of local mineralization was noted. The heavy mineral fractions of the tills are universally enriched in Mn-rich siderite thought to originate on or in the Paleozoic section of the Hudson Bay lowlands.From Seal River northward to Thelon River, near Baker Lake, tills contain only components originating west of the Hudson Bay sedimentary basin. Near the Keewatin-Manitoba border, all till is enriched in uranium, which probably originates in the ""young"" porphyritic granites underlying much of the region, and produces a distinctive airborne radiometric anomaly.At the Thelon River, multiple till sections are variously enriched in Cr, Ni, U, Cu and Mo in the vicinity of a distinctive aeromagnetic anomaly.From Thelon River northward, several coincident zones of chromium and uranium enrichment are found where the line of boreholes crosses east-west-striking belts of volcanic, ultramafic and sedimentary rocks of the Prince Albert Group.The results of this study indicate that till tends to have characteristic element associations or concentrations over each of several broad regions along the pipeline route. These are related both to large-scale bedrock associations and to largescale effects of glacial dispersal. In addition, the samples, collected more or less at random with respect to local bedrock geology, have intersected several small-scale geochemical anomalies that appear to be related to zones of mineralization of possible economic interest."

Jan 1, 1980

By L. Avramovic, B. Han, R. Jonovic, Z. Stevanovic, K. Haga, S. Dimitrijevic, A. Shibayama, L. Godirilwe, Y. Takasaki

Pyrite (FeS2) and chalcopyrite (CuFeS2) which could not be recovered, are present in mine tailings discharged from Bor copper mine. About 0.3% of copper (Cu) is contained in these tailings, therefore it can be considered as a useful copper resource. At the same time, pyrite is known to promote acid mine drainage, therefore it is necessary to detoxify the tailings. An efficient method has been proposed to recover copper and reduce the environmental impacts of tailings by a combined hydrometallurgical process of high pressure leaching (HPL), solvent extraction (SX) and electrowinning (EW) process. HPL process yielded high copper leaching rate (>95%) when water (H2O) was used as a leaching media. On the other hand, pyrite contained in the tailings was converted to iron oxide by high pressure leaching. Stability evaluation of the residue obtained from high pressure leaching, confirmed almost no elution of metal ions. The percentage of copper extracted and stripped from the Cu-loaded organic phase reached 97.4%. Moreover, it was confirmed that a low iron concentration in the electrolyte of copper electrowinning, resulted in the improvement of current efficiency of copper electrodeposition. INTRODUCTION Mine tailings are a by-product obtained from the flotation process and there are billions of tons of already existing tailings all over the world. Moreover, several billion tons of additional copper tailings will inevitably be produced in the coming years (Onuaguluchi & Eren, 2012). With the declining average copper ore grade, alternative sources of copper are highly sought, mine tailings have a comparable copper grade to that of low-grade ores (0.2–0.3%) therefore, it can be said that copper mine tailings present a very important source of secondary raw material for copper production (Antonijevi´c et. al., 2008). Consequently, it is necessary to confirm the possibility of the valuable metals (such as copper) recovery from mine tailing in which copper content is about 0.2–0.3%. Our group investigates the flotation and high pressure leaching processes for recovering of copper from mine tailings. Previous work on related samples include copper and nickel flotation tailings from Botswana, and a low–grade copper ore sample from Chile. Impurities, which are associated metals in mine tailing such as iron (Fe) and aluminum (Al) co-dissolve into the solution during the HPL treatment process. Therefore, separation of copper from impurities is necessary for selective extraction of copper from mine tailings and upgrading the copper concentration in the leachate to enable further purifying of Cu by electrowinning. Thus, it is important to investigate the possibility of applying solvent extraction for concentration of copper from leachate solutions of mine tailings (Onuaguluchi & Eren, 2012; Antonijevi´c et. al., 2008). In this study, LIX-84I was used as an extractant of copper from the leachate of high pressure leaching of mine tailing. As a fundamental solvent extraction investigation, the extraction behavior of copper was studied using a simulated solution of the leachate from the high-pressure oxidative leaching of mine tailing. The effects of; solution pH, extraction time, extractant concentration and phase ratio on copper extraction and sulfuric acid (H2SO4) concentration on stripping were investigated.

Jan 1, 2019

By Frederick J. Browne

Water, water everywhere, but not a drop (fit) to drink! Trite, but how often only too true? What is there met with in mining which, under various circumstances, may be said to be the most sought-for and highly-prized and also the most objectionable and most feared? Water! What visions that combination of five letters brings to all thoughtful minds? Up to near the end of the eighteenth century water was thought lo be an element but was then discovered to be the result of the combustion of two volumes of hydrogen with one volume of oxygen, and water so produced is chemically pure. Pure water is a clear and colourless liquid when seen under ordinary conditions, but appears bluish when seen through a long tube, and this same bluish tint may be observed in many lakes, especially those of glacial origin. A story often told describes a prospector in the desert who, failing to find water to replenish his canteen, suffers torture and death under fearful circumstances. Then again we may recall the flooding of mines, where water poured in so quickly that there was no opportunity of saving the unfortunate workmen. Instances might be multiplied without number showing that either the lack or excess of this essential fluid has taken heavy toll of human life. In all branches of mining and associated industries water must be dealt with to a larger extent, from an economic point of view, than any other substance, and very often the purity of the water is a matter of considerable importance.

Jan 1, 1925

By F. Bélanger, P. A. Fournier

"Modelling and optimization techniques used in the operation of the Detour Lake Mine leach circuit are contrasted to a 1973 review of contemporary techniques used by a major gold producer. The leach circuit at the Detour Lake Mine was modelled using a full factorial Design of Experiment of stirred tank reactor leach tests using circuit feed. Contour plots of extraction were applied in the plant to optimize addition rates of cyanide and the newly-commissioned lead nitrate system. Contour plot sections were used to understand the impact of sulphur in circuit feed at different operating dissolved oxygen concentrations. The 1973 review paper offers insight into industrially-applied modelling and optimization techniques. In particular, a mathematical model of plant data was developed using multilinear stepwise regression analysis. The model was presented using graphical representations available at the time and applied to optimize the rates of cyanide addition. Off-the-shelf software solutions of today allow mineral processors to quickly and easily visualize data, allowing them to re-allocate time and resources spent processing data to generating raw data and extracting actionable information.IntroductionModelling and optimization in mineral processing is the art of reducing reality through judicious use of assumptions to understand a process and leverage this knowledge to engineer practical solutions to metallurgical problems. Data analysis is at the core of this enterprise.While this paper showcases the modelling work done at the Detour Lake Mine (DLM), the primary objective is to pause and reflect on how far the field has progressed since the 1970’s. A snapshot of state-of-the-art gold cyanidation modelling at that time is a review paper of the Anglo American Group’s capabilities (Brittan & van Vuuren, 1973). The objective of this paper is not a play-by-play of the evolution of modelling and optimization since that time. Rather, it is a comparison of the field at two points in time.In 2016, DLM undertook an extensive bench-scale leach circuit modelling program to better understand the impact of cyanide, dissolved oxygen, lead nitrate, grind size, density, and pH on gold cyanidation (Fournier, 2016). Two major capital expenditure projects were anticipated for 2017: improvements to oxygen control and a lead nitrate distribution system. While the lead nitrate system was planned for construction, the design parameters had not yet been selected. Following the development of the model, plant trials were executed to validate aspects of the model and the methodology was expanded to address other plant issues, in particular the effect of talc chlorite and pyrrhotite in leach feed.The variables of the bench-scale study are summarized in Table 1. Dependent variables were varied using a full factorial design of experiment with two repetitions for each test condition, yielding a total of 300 tests. Test order was randomized to eliminate bias from independent variables."

Jan 1, 2018

By D. C. McDonald

"IntroductionTHE GIANT YELLOWKNIFE property is on the west side of Yellowknife bay, Great Slave lake, N.W.T., some 600 air miles north of Edmonton. This paper deals with the underground development and mining of the complex system of orebodies which have produced, in the first fifty-six months of operation (May, 1948, to December, 1952), 652,464 tons of ore with an average grade of 0.80 ounces of •gold per ton (1).The mine has been developed from three vertical shafts designated A, B, and C. Figure l shows the positions of these openings with respect to the known ore-bearing zones and the surface plant.A shaft was sunk to a depth of 522 feet in 1945-46, primarily as a prospect shaft for investigation and development of the East Zone orebody. Drifting was carried out on the 200-and 325-foot levels. Before this development had been completed it was clear that the funds immediately available made it imperative to get revenue from production as soon as possible. By the beginning of 1946, the remarkably high-grade character of the ore in the present B Shaft area had been established by surface drilling, and the decision was made to obtain initial production from this source. Since known orebodies at shallow horizons were to be developed quickly, the choice of a suitable rock outcrop for the shaft was something of a problem."

Jan 1, 1953

By N. A. Beier, N. Slingerland

"Oil sands tailings impoundments rank among the largest (spatially) in the world, covering a total of approximately 220 km2 of northern Alberta, Canada. A preliminary geomorphic design for an oil sands tailings storage facility (TSF) landform was completed with the goal of eventual closure and delicensing in mind. This paper outlines methods identified during the design process that streamline closure when implemented early in the mine planning and TSF design stages. With most oil sands TSFs currently in active operation (and some still in the planning stages), geotechnical engineers and mine planners have the opportunity to make operational and design decisions, such as those outlined herein, that are likely to improve the geotechnical and environmental performance of the landform post closure. ¦ KEYWORDS Alberta, Athabasca oil sands (AOS), Landform design, Reclamation, Sand dam, Tailings storage facility (TSF) RÉSUMÉ Les bassins d’accumulation des résidus issus des sables bitumineux font partie des plus grands (en termes d’espace) au monde, et couvrent au total environ 220 km2 dans le nord de l’Alberta, au Canada. Une conception géomorphologique préliminaire a été réalisée pour le modelé d’une installa¬tion de stockage des résidus (ISR) issus des sables bitumineux en gardant à l’esprit la fermeture et le retrait de permis à terme. Cet article présente les méthodes identifiées pendant le processus de conception qui simplifient la fermeture lorsqu’elles sont mises en oeuvre dès les premières étapes de planification de la mine et de conception de l’ISR. La plupart des ISR issus des sables bitumineux se trouvent dans des exploitations actives (dont certaines en sont encore aux étapes de planification), aussi les ingénieurs géo¬techniques et les planificateurs miniers ont la possibilité de prendre des décisions en termes d’exploita¬tion et de conception, telles que celles présentées ici, qui pourraient améliorer la performance géotechnique et environnementale de la phase suivant la fermeture du modelé. ¦ MOTS CLÉS Alberta, assainissement, barrage de sable, conception du modelé, installation de stockage des résidus (ISR), sables bitumineux de l’Athabasca (SBA)INTRODUCTION The Athabasca oil sands (AOS) underlie 140,200 km2 of land in northeastern Alberta, Canada. Oil sands located within 100 m of the original surface account for 4,800 km2 of the total area and are considered to be economically mineable (Figure 1; ERCB, 2009). Bitumen, the thick, tar-like substance contained in the AOS, is extracted through open-pit mining and in-situ methods. During mining, the overburden is first removed as waste and the sandy, bitumi¬nous ore (“oil sand”) is transported to processing facilities via conveyor belts and 400 t trucks. Warm and hot water, as well as process aides such as caustic soda, are mixed with the oil sand, creating a slurry from which bitumen is mobilized and extracted. The resulting slurry waste product is called “tailings” and contains mineral solids, process water, and small proportions of unrecovered bitumen (Masliyah, Zhou, Xu, Czarnecki, & Hamza, 2004; Sobkowicz & Morgenstern, 2009)."

Jan 1, 2019

By J. A. Hansuld

"THIS SESSION marks something of a milestone in that it is, as far as I know, the first session at a CIM Annual Meeting devoted entirely to exploration geochemistry. This is an indication of the general acceptance and widespread recognition by industry of geochemistry in mineral exploration. As a first, I hope it proves sufficiently successful and interesting that geochemical exploration sessions will become a routine part of future CIM annual meetings. The greater use and acceptance of geochemistry has resulted in many investigations and advances, especially in areas such as the Canadian Shield. For a first session on geochemistry, the meeting in Quebec suggested an ideal opportunity to assess these advances and report on the current application of geochemistry in the Shield. The theme of the session is ""Geochemical Exploration in the Canadian Shield - The State of the Art."" A series of six papers will be presented dealing with the various dispersion media - rocks, heavy minerals, ""soils"", lake sediments, waters and vegetation. As a background to the individual presentations, I would like to take a few minutes to briefly trace the history of the use of geochemistry in the Canadian Shield."

Jan 1, 1971

By T. A. Wedge

This paper suggests a crude correction for the impact of raw material quality on factor productivity in the Canadian mining industry. Such a correction would give a figure more dependent on the changing efficiency of the use of labour and capital, and less dependent on the effects of unquantified changes in inputs.

Jan 1, 1973

By M. Zamalloa, P. J. Mackey, P. Coursol, Y. Prévost

"Over the last decade or so, the availability of commercial thermodynamic modelling packages, such as FactSageTM, have been utilized to help the plant optimize slag chemistry and to minimize slag handling issues that can arise, such as those due to a process upset, for example, by undue feed variability. This paper illustrates an extension of the application of this software in examining a large range of NCV operating parameters, such as the %Fe/SiO2 ratio in the slag and the level of minor gangue components in the slag including CaO, Al2O3, ZnO, MgO, and PbO. The conditions influencing the slag liquidus range of NCV slag are discussed with respect to the overall process chemistry.Given that a sufficiently low %Fe/SiO2 ratio is used in NCV slag, most components such as CaO-ZnOPbO- Al2O3-MgO, in small concentration, all contribute to lowering the NCV slag liquidus. Considering the present level of these minor components, the NCV can operate consistently at 1200°C if the %Fe/SiO2 is between 0.6 and 0.8 in the slag. Using the type of phase diagrams presented in this paper, it is possible to develop different Noranda reactor/Noranda converter operating strategies adapted to the feedstocks available at Xstrata mines/plants or from other sources. The NCV is unique in that a fayalite-based slag is employed for high-efficiency continuous converting with excellent operating results."

Jan 1, 2007

By M. Nakai, G. Itoh, R. Yamada, A. Kurumada

In order elucidate the mechanism for poorer fatigue properties of 7000 series aluminum alloys than those of 2000 series alloys, the effect of the test environment on the fatigue crack growth of the two series alloys was investigated, considering the relationship to hydrogen embrittlement. Two 7075-type and four 2024-type alloys were T6-tempered and T4-tempered respectively, and subjected to fatigue crack growth tests in moist and dry environments. When tested in moist air, fraction of intergranular crack path was higher in the 7075-type alloy with coarse equi-axed grains than in the 2024-type alloy with similar microstructure. This was in accord with the larger crack growth rate in the 7075-type alloy. Both the intergranular crack path fraction and the crack growth rate were decreased by changing the environment to the flow of nitrogen gas. Thus, the large fatigue crack growth rate of the 7075-type alloy is attributable to hydrogen embrittlement.

Jan 1, 2015

By B. I. Boyko

As part of the Ministry of the Environment's Resource Recovery Program, the Province of Ontario has constructed a $13 million "Experimental Plant for Resource Recovery" in Metropolitan Toronto. The technology and unit operations involved in the processing of municipal solid wastes at a rate of 40 tons per hour at this facility are reviewed. Shredding, air separation and classification, screening, magnetic separation and composting are some of the operations featured at this plant. Recoverable commodities expected include paper, ferrous metals, an air-classified light fraction (shredded paper and film plastic), glass and compost. Existing and potential markets for these materials are discussed.

Jan 1, 1978

By L. K. Daneshmend

The mine of the year 2020 will need to be based on a new way of mining. It will employ technology in a paradigm that assumes responsibility for sustainable development: taking account not only economic but also ecological and social issues. This will require a holistic approach to mine design and planning, considering all controlling factors and impacts (technical, economic, environmental and social). A national collaborative strategy is required to address the several options that exist for the development and application of 2020 mining technology. Key issues in implementing 2020 mining technology will also relate to human resources, in terms of employment, skills and education. A need exists to proactively prepare for 2020 through development of a comprehensive education and training strategy.

Jan 1, 1998

AT the Annual General Meeting held in Winnipeg last March, the whole of one of the technical sessions was devoted to a special Symposium on Geological Investigations in Canada, introduced by a paper entitled The Geological Survey (lî which had been specially prepared by Dr. G. A. Young, Chief Geologist of the Survey, and had been published in the February BULLETIN, prior to the meeting. Geologists from each of the provinces contributed to the Symposium, including directing officials of the geological divisions of provincial Departments of Mines, representative geologists from the Universities, and company and consulting geologists. Space, unfortunately, does not permit publication of a complete record of the proceedings,_ or even inclusion of all contributions to the discussion. The following summary, however, gives what is believed to be a fair cross-section of the opinions expressed by representatives from each Province. The Symposium resolved itself largely into a discussion as to how the Geological Survey and the several provincial bureaus or divisions of geology could co-operate most effectively in the important task of carrying out geo-logical investigations, with avoidance of duplication of work and waste of effort, and, so far as broad principles are concerned, there was remarkably close agreement among those participating in the Symposium as to how the various types of investigation should be allocated as between the Federal and Provincial organizations. Briefly, the concensus was that the Geological Survey can render the most effective assistance by conducting reconnaissance investigations, with mapping at 4 miles to one inch, leaving to the provincial organizations the more detailed, and hence more local, studies and mapping at larger scales. There was general agreement that the preparation of base maps, essential to systematic geological investigation, is a service devolving upon the Federal Government.

Jan 1, 1940

By CIM Mineral Resource, Mineral Reserve Committee

Industrial minerals are generally considered to include non-metallic minerals, mineral products, or materials that provide raw material inputs for the construction, chemical, and manufacturing industries. They are often relatively low-value and bulky materials that are generally used close to where they are produced; however, some raw materials may be transported hundreds of kilometres to manufacturers and customers (ENDM, 2021). They do not include the metallic minerals, mineral fuels, or gemstones, and are used in industries based on their physical and/or chemical properties (Wikipedia, 2021). In contrast to most metallic minerals, a general distinguishing characteristic of the industrial minerals sector is their general low degree of market elasticity in relation to the market prices and product specifications. The estimation of either a Mineral Resource or a Mineral Reserve (MRMR) for an industrial minerals deposit can be affected to a significant degree by a number of factors that are not typically applicable to metallic mineral deposits. These factors can include such considerations as the particular physical and chemical characteristics of the final product, product quality issues, market size and market access. In some cases, such information may be confidential and proprietary. One of the key challenges of the industrial minerals sector is to define a commonly accepted listing of which types of minerals, materials, or mineral deposits can be considered as industrial minerals (Mining Standards Task Force, 1999). Although definitions for what constitutes an industrial mineral can vary in detail, general descriptions can be found in American Geosciences Institute (2021), Fastmarkets IM (2021), Snowden (2019), SME (2021) and Wikipedia (2021). A brief listing of some of the materials and minerals that are generally considered to be industrial minerals is provided in Table 1. For the purposes of this document, all references to industrial minerals include not only the minerals, materials, and mineral deposits themselves, but also the various commercial products that are derived from these sources.

Nov 19, 2023

By H. U. Ross

ROASTING is usually thought of as a process in which finely crushed or ground ore is heated with air in a suitable furnace in which the ore is rabbled or agitated in such a way as to insure complete reaction between the oxygen of the air and the oxidisable constituents of the ore. Roasting in this sense is used only to a very limited extent in the iron and steel industry. This is because, in most iron ore deposits mined today, the ore is of a type that does not require roasting. Where this process is used, it is usually because of some special circumstance, such as a peculiar economic condition, that warrants it. If roasting is looked upon in the broader sense as a gas-solid chemical reaction carried out at an elevated temperature in which both gaseous and solid products are formed, then the process is used in the iron and steel industry to a greater extent

Jan 1, 1961

By M. J. King, D. A. Van den berg, R. Fukuzawa

"Mercury bearing ore bodies are often treated for the production of copper, lead, zinc, gold, and silver. The mercury deports either to tailings or is collected during various stages of the extraction process. This paper reviews the relationship between various mercury collection processes and the subsequent management of the mercury by-product or waste. It focuses on mercury removal sequestration including cementation, sulphide precipitation, bulk neutralization, and carbon adsorption. Long term mercury management strategies including third-party stabilization, stabilized mercury co-disposal, secure storage, and mercury recycle are also evaluated. INTRODUCTIONMercury is produced in North America as a by-product of non-ferrous metals processing and from recycling of products such as dental amalgam, fluorescent lamps, and thermometers. Its toxicity is recognized to have significant negative impacts on the environment and human health. As a result, many countries are adopting regulations limiting mercury use and its uncontrolled release.The European Union banned mercury exports in 2011 and the United States will do so in 2013. The export bans aim to prevent mercury use in developing countries for activities such as artisanal small scale gold mining. However, by-product mercury production from the non-ferrous metals industries continues.These factors contribute to an oversupply of mercury and the need to find suitable treatment methods for the long term management and storage of mercury and mercury bearing materials."

Jan 1, 2012