Search Documents

By M. Maldonado

This work details the application of a decentralized control strategy to a pilot flotation column working with a two-phase system (water-air). The process is represented by a multivariable system composed of three inputs and three outputs. The selected control variables are the froth depth, the air hold-up and the bias rate, whereas the corresponding manipulated variables are the set-points of the local flow controllers of tailings, air and wash water. All controlled variables are estimated using electrical conductivity based techniques. In particular, the results of a new method for estimating the bias rate, based on the measurement of the volumetric fraction of wash water under the interface, is presented. This method reduces the coupling problem associated to the bias estimation as a difference between feed and tailing water rates. Moreover, the nominal system transfer matrix can be represented by an upper triangular matrix, in such a way that the closed-loop system stability reduces to the stability of the independent control loops. The experimental results show that the closed-loop system performance, particularly that of the bias rate loop, is strongly dependent on the air flow rate, reaching in some cases the saturation point of the controller.

Jan 1, 2007

The mechanism of thiosulfate decomposition and the products formed were investigated in the presence of pyrite or pyrrhotite in copper-ammonia solutions used for leaching gold. The presence of the sulfides significantly increased the decomposition of thiosulfate. The sulfide-surface-catalyzed oxidation of thiosulfate to tetrathionate by dissolved oxygen or the cupric tetra-ammine complex was proposed to be the dominant thiosulfate decomposition mechanism. The catalysis of the sulfides in this reaction could originate from their strong affinity for aqueous sulfur species and their semiconducting properties. Oxygen was found to be the initial driving force for thiosulfate decomposition in the absence of cupric ions and the driving force for the continuous decomposition of thiosulfate in the presence of cupric ions. Under an oxygen free atmosphere, the decomposition of thiosulfate was limited to reduce the cupric ions and the catalytic effect of the sulfides was also marginal. The dominant oxidative product of thiosulfate was trithionate in alkaline solutions especially in an oxygen rich or cupric ion rich environment. Tetrathionate was found in relatively smaller amounts in an oxygen and cupric ion deficient environment. Tetrathionate was not stable and would further decompose after extended periods. Trithionate concentrations increased almost linearly with time.

Jan 1, 2005

By C. Carrasco

Caletones Smelter, Division El Teniente of Codelco Chile, has used Teniente Converter (TC) as the only smelting unit since November 2000. The modernization project considered the shutdown of the last reverberatory furnace, the installation of the fourth Teniente Slag Cleaning Furnace, the installation of a new fluidized bed dryer and the modification of the concentrate injection system into TC. The modernization project and related investments allowed for the increase of the smelting capacity up to 1.25 million t of concentrate annually.Next stage of the smelter expansion in the year 2004 considered the increase of the smelting capacity up to 1.44 million t/year. The expansion required technology modernization and the installation of the new equipment, such as concentrate injection system, oxygen plant, fluidized bed dryer and storage bin. Currently the annual smelting capacity is about 1.35 million t of copper concentrate, being limited by sulphuric acid plant treatment capacity. This paper presents the technology and production evolution in the Caletones Smelter in the years 2000 - 2006, demonstrating the potential of development and competitiveness of Teniente Converter as world-wide recognized smelting/converting reactor.

Jan 1, 2007

By Solar D. Andrés

Several large open pit mines are facing the challenge to design and plan an underground transition to sustain the long term future of their operations. The desired underground method is Block Cave since its natural high productivity and low operating cost that could compete against the open pit cost to mine the final open pit pushbacks. It has been found at several operations where this transition is taking place that the pit limit at which transition is performed is rather deep. This aims to think that perhaps several transition projects have started late in the life of an operation producing an over stress in the transition project and reducing the flexibility in the design of the overall infrastructure and a substantial lost in the complete project NPV. Traditionally the approach to plan open pit underground transition consists of sequentially deciding the final pit using a Lerchs and Grossman type of optimization to find the overall maximum pit shell and then running block cave simulations to find the best footprint for the underground option. The research summarized in this paper is related to the development of an integer linear programming model that aims to compute simultaneously the maximum NPV of the combined option final limit open pit and block cave underground footprint. The model has been tested using two large block models representing two of the current operations in the process of transiting from open pit to underground operations. Finally, the integrated open pit underground transition model is going to be compared to the traditional sequential approach in order to define which method achieves the best NPV. The paper illustrates both case studies in depth.

Oct 1, 2009

By Qing-hua Tian, Li-then Cheng, Xue-yi Guo

In order to recycle valuable metals from silver separated residue, a novel method using alkaline smelting at low temperature was proposed. The main factors affecting the main metal recovery such as the smelting temperature, smelting time, liquid-to-solid ratio and alkali addition were investigated comprehensively. The behavior of the main metal elements, such as Pb, Sn, Sb and Bi in silver separated residue was also discussed. The results indicated that amphoteric metals such as Pb and Sn can be smelted into the melt, while other metal elements, such as Sb and Bi were left in the residue.

Jan 1, 2011

By P. Sauriol

This work addresses the design challenges and demonstrates the capabilities of a novel water transfer factor measurement apparatus. Several measurement concepts were screened on the basis of their water transfer factor accuracy using Monte-Carlo generated virtual experiments. The most promising measurement concept was assembled and tested to assess its actual measurement accuracy. For these concept validation experiments, the polymer electrolyte membrane fuel cell was simulated by adjusting the water injection rate to corresponding levels. Combining the anode and cathode measurements, the water transfer factor accuracy was typically better than 0.01. Real-time measurements of the water transfer factor on both anode and cathode sides of a polymer electrolyte membrane fuel cell were achieved. The anode and cathode side measurements were in good agreement with each other; however the anode side measurements were generally more reproducible. A parametric study showed that stream humidification plays an important part in the water transfer across the membrane electrode assembly. Finally the water transfer factor along the channel of a 300cm2 co-current fuel cell was obtained by using a series of six 50cm2 sub cells. The results were in good agreement with predictions from a recently proposed model.

Jan 1, 2005

By C. Anderson, H. Huang, P. Miranda, E. Dahlgren, I. Chandra, M. Jeffrey

The latter part of the 20th century saw great advances in the treatment of refractory gold ores coupled with increased reliance on the use of cyanide for gold processing. Now, in many parts of the world, there is social pressure to limit or eliminate the use of cyanide. As well, treatment of some refractory ores or concentrates which have excessive cyanide consumption, gold cyanide pregrobbing or significant sulfide content remain difficult. This paper will outline the history of the development of alkaline sulfide leaching as an ancillary process to nitrogen species catalyzed (NSC) pressure leaching. Electrochemical fundamentals and the applicable thermodynamics of the alkaline sulfide hydrometallurgical system will be outlined. As well, examples of refractory gold recovery with alkaline sulfide hydrometallurgy such as an arsenopyrite gold concentrate application, a chalcopyrite gold concentrate application, a pregrobbing gold ore application, and a cyanide consuming gold ore application will be delineated in this paper.

Jan 1, 2005

By D. W. Heard

Electrospark Deposition (ESD) is a low heat-input, high energy density, micro-welding process. The short pulse duration and high-pulse frequency, in combination with the small amount of material transferred during each pulse, results in the evolution of extremely rapid cooling rates, believed to approach 105-106 °C/s [1]. This rapid solidification event results in the refinement of the microstructure to the nanostructured or amorphous level [2, 3]. Figure 1 displays the resultant microstructure of an Al-17%Si alloy deposited by the ESD process. Furthermore, it was determined that the microstructure of the deposit remained unchanged after subsequent layers were welded onto the presented layer. Freeforming of materials is a rapid prototyping process in which the deposited feedstock is built-up to the desired geometry in a near-net shape manner. Figure 2 displays the automated set-up employed produce three dimensional freeformed objects via multiple deposition trials of the ESD process. The automated XYZ table is equipped with CNC software to transform CAD renderings into three dimensional tool paths. Figure 3 displays an Al-12Si freeformed gear (2" diameter, 12 teeth) produced by the ESD process, prior to removal from the substrate. An SEM analysis of the freeformed component showed that the microstructure did not coarsen during the deposition of subsequent layers during the freeforming process, as depicted in Figure 4, resulting in the production of a bulk nanostructured component. This paper represents a summary of the capabilities of ESD to fabricate advanced materials possessing refined microstructure. In particular, results on the microstructural evolution obtainable for various wear-related systems will be presented. In addition, the feasibility of using the ESD process to freeform three-dimensional objects via multiple deposition passes will be presented and accompanied by a characterization of the properties of the freeformed component. [1] R. N. Johnson, "ElectroSpark Deposition: Principles and Applications," in Society of Vacuum Coaters, 2002, pp. 87-92. [2] J. Milligan, D. W. Heard, and M. Brochu, "Formation of nanostructured weldments in the Al-Si system using electrospark welding," Applied Surface Science, vol. 256, pp. 4009-4016. [3] S. Cadney and M. Brochu, "Formation of amorphous Zr41.2Ti13.8NilOCul2.5Be22.5 coatings via the ElectroSpark Deposition process," Intermetallics, vol. 16, pp. 518-523, 2008.

Jan 1, 2010

By F. Rashchi, N. Naseri Joda

Recycling of electronic wastes is an important subject both from an environmental point of view and also the recovery of valuable materials. In this research, PC board scraps were leached to recover Cu, Ag, Au and Pd. Due to the high cost of the shredding process and to avoid secondary pollution from odors and dusts, board scraps were cut into 5X5 cm2 pieces. To determine the most effective leachant, aqua regia, nitric acid, hydrochloric acid, ammonium persulfate and potassium persulfate were tested. The effect of the leaching parameters, the leachant concentration, temperature, leaching time and liquid to solid ratio were studied and optimized using response surface methodology.

Jan 1, 2011

By R. A. L. Drew, G. Mendoza-Suarez, J. Filipi, R. Vintila, J. A. Kozinski

Economics and environmental considerations along with the increasing demand of hydrogen encourage development of novel technologies such as plasma processing of hydrocarbons and thermal cracking of natural gas. Plasma discharges, either in thermal or non-thermal regimes are expected to allow low temperature and fuel flexible on-site hydrogen generation. The main drawback of thermal plasma reformers is the high-energy consumption resulting from high-temperature operation. On the other hand, non-thermal plasma, generated by dielectric barrier discharge (DBD), is able to simulate the chemical reactions employing much lower energies than those required by thermal treatment processes. The non-thermal plasma process allows for instance, a direct conversion of methane into hydrogen and carbon black with no CO2 release. The focus of this research was on the GHG-free method of H2 generation in compact non-thermal plasma reactors using low, medium and high permittivity dielectric ceramics. A stable, non-thermal plasma was generated by placing a dielectric ceramic between two electrodes with a 25 thou gap and applying an alternating current of 1-5kHz and voltages of 4-8kV. In order to ensure energetic efficient plasmas, experiments were conducted to analyze the behaviour of different permittivity ceramics. It was found that the dielectric properties of a ceramic, when used in a DBD reactor, have a strong influence on the discharge characteristics, which in turn influence the power consumption. Higher dielectric constant resulted in higher conversion rates of methane (higher yield of hydrogen and carbon). At the same time, the mechanical properties of the dielectric material, which are closely associated with its processability, influenced its resistance to electron bombardment, as well as thermal and mechanical damage. Therefore a reliable ceramic should have good dielectric properties, in addition to good thermo-mechanical stability.

Jan 1, 2004

By N. Tounsi

The use of analytical modeling of continuous chip formation in conjunction with orthogonal cutting experiments was presented in the open literature to identify the coefficients of material constitutive equation within the practical range of stress, strain, strain rate, and temperature encountered in metal cutting. Identification of reliable constitutive data was hampered by a lack of a reliable model for the prediction of the primary shear zone thickness that affects directly the effective strain rate field. An original analytical model to determine the primary shear zone thickness is proposed in this paper. It is based on the mechanics governing the material flow in the primary shear zone. Based on the distribution of the hydrostatic pressure and the forces measured from orthogonal cutting tests, the model that describes the thickness of the primary shear zone is derived. To validate the model, FE simulations of chip formation using DEFORM3D were carried out for different materials and cutting conditions. The results of the analytical model are in reasonable agreement with FEM results.

Jan 1, 2006

By Li Xibing

The In order to mine safely with reasonable cost, it is necessary to research the fracture characters of backfill and its matches with rock mass. Four kinds backfill with cement-tailing ratio of 0.250, 0.125, 0.100 and 0.083 respectively were tested, and basing on stress-strain curves tested, the deformation characters and fracture laws as well as the damage constitutive equations investigated with damage mechanics whose calculating results are coincided with experiment results well were proposed. The results of damage analysis show that there have different damage characters in different backfill, e. g. the lower the ratio of cement to tailings the lower the damage values when stresses reach to peak value; the lower the content of cement the more rapid in damage and the more abrupt in breakage process. In addition, using catastrophe theory, an energy model was proposed for backfill and rock mass acted each other in mechanics, and the unstable condition of the system was obtained. Research results show that the higher is the stiffness of rock mass the more stable the system, and the lower is the ratio of cement to tailings, the more unstable the system will be. Further more, according to the catastrophe model proposed, the reasonable matches between backfill and rock mass were researched, and a calculation formula that designs reasonable strength of backfill during mining was put forward. It has been proved by practice that the model and theory researched in this paper can guide filling design in mining. Keywords: Cemented tailings backfill, constitutive equation, catastrophe theory, match of backfill and rock mass

May 1, 2007

By F. Habashi

Magnesium is the eighth most abundant element in the earth's crust, It occurs in nature in sea water, brines, and a number of minerals, Metallic magnesium was first isolated by Humphry Davy (1778-1829) in England in 1808 via electrolysis of anhydrous magnesium chloride with a mercury cathode, Antoine Bussy (1794-1882) in France extracted the metal in 1828 by reducing fused magnesium chloride with metallic po¬tassium vapour, The first industrial production of magnesium by electrolysis of molten carnallite began in 1886 in Hemelingen in Germany, In 1940 Lloyd M, Pidgeon (1903¬1999) in Canada pioneered the first industrial metallothermic magnesium extraction plant based on the reduction of dolomite with ferrosilicon under vacuum, Since then the magnesium industry developed further and a variety of processes are presently used.

Jan 1, 2006

By S Sokhanvaran

Electrodeposition of silicon from a cryolite based electrolyte at a relatively low temperature (1000°C) is a promising approach to generate high purity silicon. In order to obtain fundamental data pertaining to electrowinning of silicon from Cryolite?SiO2 melts, density and electrical conductivity measurements were made. A range of temperatures and SiO2 contents was studied for each property. It was found that while density has an inverse relationship with temperature, the dependence for electrical conductivity is direct. Increasing silica content up to the saturation limit (~ 5 wt%) increases the density whereas further increase in SiO2, lowers the melt density. On the other hand, the conductivity is lower for the melts with greater SiO2 content, at any temperature.

Jan 1, 2011

By Hassan El-Shall, Ayman El-Midany, Patrick Zhang

Bench and pilot scale testing results suggest that significant improvement in dewatering characteristics of fine particles could be obtained by the addition of fibrous materials. Case studies involving flocculation and dewatering of wastes from phosphate, bauxite, and kaolin processing plants are presented in this paper. Several dewatering techniques were investigated, including sedimentation thickening, filtration, centrifugation, dewatering on screens, and seepage-induced dewatering and consolidation. Advantages and limitations of commercial application of some of the developed techniques arc discussed.

Jan 1, 2004

In the flotation of a copper ore, entrainment of fine silicate and iron sulfide gangue minerals resulted in poor copper concentrate grade. In the cleaning stage, rejection of these gangue minerals was particularly difficult due to severe mechanical entrainment when the rougher concentrate was ground to 10 µm. To reduce gangue entrainment, polymeric depressants were tested. The rationale being that with the use of such polymeric depressants that also possess flocculation power, not only minerals-to-be-depressed can be made hydrophilic, but their particle size can also be enlarged. In this manner both the "genuine" flotation and the mechanical entrainment can be reduced. An effective polymer to reduce entrainment of silicate gangue mineral in sulfide flotation was identified from bench flotation tests conducted on single minerals. It was then applied to the flotation of a copper-gold ore confirming the beneficial role of the polymeric depressant in the reduction of fine gangue entrainment.

Jan 1, 2007

By F. Bosché

Previous research has shown that ?Scan-vs-BIM? systems are powerful to provide valuable information for tracking structural works (progress, quality, safety). However, the transferability of this capability to other construction areas such as MEP works has not been assessed so far. Comparatively, the construction of MEP systems, in particular pipes and ducts, tends to be more flexible with respect to the positioning of individual components, so that Scan-vs-BIM systems could be defeated when tracking MEP installation works. This paper presents recent results on the feasibility and performance of using a Scan-vs- BIM system to track MEP works. The approach followed is presented and then tested with two real-life challenging case studies were conducted simultaneously but totally independently in Canada and Italy. The results show that, as expected, pipes and ducts tend to be more loosely positioned than structural elements leading to a poorer performance of the Scan-vs-BIM system. Nonetheless, it appears that the system works well to assess the level of conformance of site installation works, providing valuable information for estimating emerging performance metrics like ?percent built as-designed?. In addition, the proposed system could also be useful to accelerate and thus reduce the cost of delivering as-built BIM models for in the case of new builds.

Aug 1, 2013

By C S. Stevens

This paper describes the problems encountered and the steps taken to solve them in milling an ore containing relatively large amounts of pyrrhotite. A complex and greatly lengthened flotation circuit was required to recover the pyrrhotite. A very low pH had to be maintained in the cyanide circuit in order to get good recovery of the gold and maintain reasonable cyanide recovery. Introduction D ELNITE Mines Ltd., a gold mine situated about 5 miles by road south and east of the town of Timmins, Ontario, is serviced by two shafts. No. 2 shaft extends from surface to the 2875-ft. level, and No. 3 shaft, an internal winze, extends from the 2875-to the 5275-ft. level. No. 2 shaft was stopped at the 2875-ft. level because of a heavy band of chloritic schist which necessitated a drive to the north for 1000 feet, where No. 3 shaft was sunk. The latter bottomed in the schist at the 5275-ft. level. From the 2500 to the 2875-ft. level in No. 2 shaft, the ore was

Jan 1, 1965

By G. Bonnivard

"A complete laboratory process for the treatment of lateritic ores containing a high proportion of iron, as well as chrome and alumina, has been established. The ores treated originate from the tropical zones and result from superficial climatic alteration. According to recent estimates, the known reserves of such ores reach many billions of tons, thus representing huge potential reserves for the elements they contain.The process used is based on the alkaline roasting of pelletized ore in the presence of sodium carbonate. This treatment results in the separate recovery of pellets of upgraded iron ore, pure chrome oxide and hydrated alumina. The research described in the paper aims at determining the best experimental conditions for obtaining the highest extraction of the required oxide from this type of ore."

Jan 1, 1967

By H. R. Shakeri, R. Mayer, M. J. Worswick, A. Rahem

The current focus of research and development in transportation industry is to use lightweight materials such as aluminium alloys for more structural components. In this regard, maintaining safety of the passenger and vehicle is the most important; therefore crashworthiness of components made of lightweight materials must be evaluated prior to sizable application of these materials. The focus of the present study is to understand failure and damage mechanisms during the axial crushing of aluminium tubes made of A1Mg3.5Mn alloy of 2 and 3.5 mm thickness. Due mainly to complexity of the crushed tubes, a microstructural approach is considered. In this study optical, stereo as well as scanning electron microscopy techniques have been used to study damage and failure mechanisms in these types of tubes, which are essential energy absorbing components in passenger vehicles.

Jan 1, 2006