Search Documents

By D. J. Wesolowski, D. A. Palmer, P. Bénézeth, S. Hilic

The equilibrium solubilities of gibbsite, Al(OH)3, and boehmite, A1OOH, have been extensively studied in our laboratory from 30 to 90°C, and 100 to 300°C, respectively, to ionic strengths of 5 mol.kg-1 (NaC1) over a wide range of pH. The resulting solubility constants have been treated with consistent empirical models that incorporate appropriate experimental data taken from the literature. These studies were initiated in part to understand and quantify scale formation in geothermal fields as a result of fluid re-injection from electric power generating plants. Most of the experimental results were obtained through application of a unique potentiometric method that allows for rapid, precise measurement of the in situ pH and allows the approach to equilibrium to be monitored from under- and super-saturation. The experimental program was extended to deal with more basic solutions (e.g., five molal NaOH), in which the dissolution of boehmite was measured for application to the refining of bauxite by the Bayer process. More recent results in strong caustic solutions at temperatures below 90°C were obtained to investigate the dissolution of aluminum-containing sludge from holding tanks at the Savannah River waste reprocessing site. In this case the solubility enhancing effects (kinetic and equilibrium) of triethanolamine were also established and quantified. Finally, potentiometric solubility experiments were conducted (50°C in 0.l mol-kg-1, NaCl) on aluminum alloy sheets to identify mainly the nature of the aluminum oxide/hydroxide surface layer formed under these conditions.

Jan 1, 2004

By Junhyun Choi, Allan Gomez-Flores, Chonbuk National University, Siyoung Q. Choi, Gahee Kim, Seungkon Kim

In this study, to confirm the effect of depletion attraction on the flotation, we theoretically and experimentally investigate the effect of the depletion attraction force on flotation. While varying the concentration of the depletion agent (polyethylene glycol), three different systems are studied: pure malachite, pure silica, and a 1:1 mass ratio of malachite and silica binary system. We find that recovery increases significantly as the concentration of the depletion agents increases for all three systems, as the depletion agent facilitates the adsorption of the particle on the bubble surface. However, the recovery suddenly decreases in a certain concentration range, which corresponds to the onset of the decreased surface tension when high concentrations of the depletion agent are used. This non-monotonic overall recovery trend implies the surface adsorption of the depletant on a surface. The decreased surface tension of the air/water interface suggests that the recovery rate is lowered due to the adsorption of the depletion agent to the bubble surface, acting as a polymer brush. Based on our observations, we conclude that the depletion force can greatly improve particle adsorption, as predicted in the accompanying theory paper, while simultaneously the adsorption of the depletion agent on the bubble surface plays an important role because it hinders particle adsorption. We also perform experiments in the presence of a small amount of a collector, sodium oleate. An extremely small amount of the collector leads to the increase in the overall recovery, which eventually reaches nearly 100 percent. Nevertheless, the grade worsens as the depletant provides the force to silica particles as well as target malachite particles.

Jan 1, 2016

By J. E. Dutrizac

The dissolution of low-iron sphalerite, (Zn,Fe)S containing 0.08% Fe, in ferric sulphate-sulphuric acid media was investigated using closely sized fractions of crushed sphalerite crystals and sintered disks made from the crushed crystals. Linear kinetics are observed, and the predominant reaction products are ZnSO4, FeSO4 and elemental sulphur. The leaching rate increases systematically with increasing temperature, and the calculated apparent activation energy is 56 kJ/mol for the sized sphalerite and 54 kJ/mol for the sintered disks. The relatively high apparent activation energy suggests that the rate is chemically controlled, a conclusion supported by the insensitivity of the rate to the disk rotation speed. The rate increases as the 0.22 power of the Fe(SO4)1.5 concentration, and as the 0.22 power of the H2SO4 concentration. However, in the absence of ferric ions, the rate increases more significantly with increasing H2SO4 concentrations, and relatively rapid rates are observed in solutions containing >0.5 M H2SO4. In 0.1 M Fe(SO4)1.5-0.3 M H2SO4 media, the measured rate decreases with increasing sulphate concentrations, added as Li2SO4. The rate of dissolution of low-iron sphalerite is promoted by dissolved copper concentrations as high as 800 mg/L. In contrast, dissolved silver, even in the 0-2 mg/L concentration range, significantly retards the dissolution of the low-iron sphalerite.

Jan 1, 2008

By Raj K. Rajamani, Nikhil Dhawan

"Agglomeration has become common pre-treatment step to improve heap leach percolation thereby recovery, the fundamental understanding of the agglomeration process for crushed ores is still lacking. Agglomeration is required for ores which either contain excessive amounts of clay or an excessive quantity of fines generated during mining and crushing. Numerous experiments have been carried out in laboratory scale batch drums using different ores. It has been found out that experimental agglomerate size distributions exhibit self-preserving spectra. The self-preserving/ similarity distribution of the agglomerates is found to be independent of operating conditions and is uniquely determined by the size enlargement mechanism. An empirical model based on the absolute difference between moisture applied and optimum moisture was developed. This model uses self-preserving spectra in the form of a Rosin-Rammler distribution function to predict size distribution at different operating conditions. The empirical model was considerably easier to work with plant scale agglomeration drums. Also, a test known as dip test is developed which improves fundamental understanding of the agglomerate formation and growth mechanisms. This test also provides the progeny size distribution of each agglomerate size. The progeny size distribution was analyzed with a model that partitions the particles into a host and guest category. The ensuing partition coefficient identifies the behaviour of a particle as a host for other particles or a guest layering on other particles. This concept helps in identifying the type of agglomerate that would result for a specific feed size distribution. INTRODUCTIONHeap leaching is one of the hydrometallurgical processes that have served as a green and economically viable process for the treatment of low grade complex ores of copper, uranium, nickel, silver and gold (Dhawan et al., 2013). Heap leaching appears to be a favorable candidate for the least energy consuming process for low grade ores. In heap leach operations nowadays a pretreatment step known as crushed ore agglomeration has been implemented (Dhawan et al., 2013). A bed of agglomerates improves the uniform percolation of solution through the heaps of ore. Therefore, it was possible to treat wastes and mill tailings via agglomeration and heap leaching. Agglomeration pretreatment is required for ores which either contain excessive amounts of clay or an excessive quantity of fines generated during mining and crushing (Bouffard, 2005; Dhawan et al., 2013).While agglomeration has become common practice pretreatment step in heap leach operations, the fundamental understanding of the crushed ore agglomeration process is still lacking. The author reviewed publications up to 2012 on the crushed ore agglomeration process and did not come up with modeling studies on the topic (Dhawan et al., 2013). Some of the possible reasons can be the stochastic nature of the process, experimental difficulties, and lack of instrumentation for fundamental studies."

Jan 1, 2016

By S. J. Cook

Copper, a world commodity, and the first metal used by man, played a great part in the beginnings of modern civilization, which rests so dependently on the utilization of metals. Then, long after the close of the so-called 'bronze age,' when iron and steel had attained great prominence as the world's most important metals, the practical application of electricity to industry and commerce, for the improvement of every phase of man's multitudinous activities, gave a new impetus to the production of copper. Improved metallurgical practice made it possible to work low-grade properties at a profit. Research disclosed many new uses for copper. The metal, now produced from the mines of the world in the proportion of about one pound to every 50 tons of pig iron, has attained an importance which rivals that of iron and steel in the commerce and daily life of every nation. New fields of copper-bearing ore have been discovered in Canada in recent years. Established mines in the United States and Chile are producing on a great scale. Africa looms up as one of the great question marks in the future of copper. Whereas, a few years ago, the end of the world?s resources was predicted as being in sight, the evidence now available seems to show that the copper production of the world is likely not only to continue, but to increase for a long time yet to come. Canada's future in copper is a great subject; in the present paper only a few of the most outstanding factors affecting Canada's destiny in this large field may be noted, but if consideration of the points raised herein serves to focus attention on the magnificent possibilities of Canada as a producer of copper, the preparation of the paper will be more than justified.

Jan 1, 1928

By R. W. Lawrence, J. B. Austin, P. B. Marchant, J. T. Chapman

"Biohydrometallurgy is the use of microbiological reactions to assist in the extraction of metals. Bioleaching offers an innovative alternative for the treatment of refractory gold-bearing sulphides (1). One particular cost advantage of bioleaching is the potential to enhance gold extraction after only partial sulphide oxidation. The apparent selective sulphide oxidation is more prevalent where the refractory gold is associated with arsenic and antimony (2). Oxidation of the pyrite minerals and arsenopyrite at different oxidation rates can result in high gold extractions at relatively low levels of sulphide oxidation due to preferential, or selective, oxidation of the arsenic mineral. Arsenic extraction rates in a bioleach process typically exceed the iron extraction rate. Therefore, in concentrates in which the precious metals are principally associated with arsenic minerals, liberation of the precious metals may be possible with high recoveries and less than complete sulphide oxidation. The capital and operating cost advantages of partial sulphide oxidation are inherently obvious and are briefly illustrated herein.Ultra fine milling (UFM) is another alternative for enhancing gold extraction from refractory sulphides. Some refractory gold is simply particle size sensitive and UFM can improve gold extraction without the need for costly sulphide oxidation (3). Fine grinding technology for enhanced gold recovery developed by Metprotech, South Africa, is currently producing 2 - 4 micron ground product using a single pass, stirred ball mill. Proper application engineering has ensured that plug flow occurs through the mill. Plug flow from the feed inlet at the bottom of the reactor ensures that short circuiting of feed does not occur and as a result, the mill product does not require classification.A combination of UFM as a pretreatment for bioleaching could provide a mechanism for enhanced selective sulphide biooxidation and/or increased overall gold extraction following biooxidation due to improved particle liberation ( 4). The effect of UFM on biooxidation costs will be discussed. Only sulphide concentrates are considered herein for application of UFM in combination with biooxidation."

Jan 1, 1990

By Yum Xiaoquan, Turgut Yalcin

"A laboratory study was carried out to determine the potential role and effect of ultrasonic irradiation in the flotation of a Sudbury copper-nickel sulphide ore. The use of ultrasound was tested separately at the pulp preconditioning, collector conditioning and flotation stages. While no significant benefits were evident in the latter two cases, ultrasonic preconditioning of pulp improved the grade-recovery performance and had the prospect of reducing reagent consumption rates. Tests were conducted on both the normal and oxidized ore samples, and several variables were investigated, including ultrasound frequency (25 kHz and 45 kHz), ultrasonic power (up to 1.6 W/cm2), duration of ultrasonic treatment (up to 60 minutes), and the intensity of pulp agitation employed during the application of ultrasound. Ultrasound frequency of 25 kHz and duration of 15 minutes yielded satisfactory results. Changes were found to occur in the temperature, pH and Eh of the pulp during ultrasonic processing. The favorable effects of ultrasound observed in this study were attributed primarily to its surface cleaning capability.INTRODUCTIONThe use of ultrasound for the surface cleaning of objects is well known. Ore flotation is based essentially on the surface properties of minerals, and hence stands to benefit from ultrasonic treatment which may help restore mineral surface characteristics that might have been lost or modified through oxidation, etc. Expected outcomes of this method of treatment include improved flotation kinetics, higher recovery, better selectivity, and savings in reagent consumption, as has been demonstrated by various researchers (Aldrich and Feng 1999, Celik 1989, Ozkan 2002, Letmathe et al. 2002, Nicol et al. 1986)."

Jan 1, 2005

By E. Essadiqi, P. Poruks, D. Boyd, D. Emadi, I. Yakubtsov, T. Turi

This paper reviews the results of an extensive study of microstructures and mechanical properties in bainitic linepipe steels. The research was carried out as a collaborative project between Queen's, Stelco and CANMET. Basic studies of phase transformations and mechanical properties in these steels established important relationships between processing schedule and microstructure evolution, and between final microstructure and mechanical properties. The best combination of strength and toughness properties is obtained with a microstructure comprising a matrix of intragranularly-nucleated bainite (`acicular ferrite - AF') and small (~ 0.5 µm) dispersed particles of martensite (`M/A'). We describe this as a dual-phase AF+M/A microstructure. An experimental study on 15-mm thick plate determined the window of steel composition and processing parameters which gives the dual phase AF+M/A microstructure. The minimum strength and toughness properties for Grade 621 (X90) linepipe steel can be achieved by either a lean steel composition (0.04C-1.77Mn-0.04Cr¬0.32Mo-0.31Ni-0.29Cu-0.08Nb) with extreme processing parameters, or by a higher alloy composition (0.04C-2.07Mn-0.50Cr-0.51Mo-0.04Nb) with a more industrially realistic processing schedule. It is proposed how this approach could be extended to obtain higher strength linepipe grades.

Jan 1, 2005

By C. S. Maggs, L. Shwydiuk, H. W. Newcomen

The southwest wall of the Lornex Pit at the Highland Valley Copper mine has been experiencing slope displacements since 1978. Measures to manage the displacements on previous pushbacks have included stepping out, scheduling pushbacks to unload the crest of unstable areas, slope dewatering and mining with intensive slope monitoring. The final pushback on this wall is currently being mined and substantial modifications to the slope geometry could prove to be uneconomical. As a result, a campaign of surface water collection and diversion, horizontal drainhole drilling and deep well drilling is currently underway to maintain an acceptable degree of stability to the end of mine life. The various factors contributing to instability, including engineering geologic controls, rock mass strength, and surface and groundwater hydrology are presented. Movement trends, displacement magnitudes and stability analyses results are also discussed.

Jan 1, 2003

By Jan E. Nesset, Phillip J. Mackey, Joo Y. Kim, Giovanni Di Prisco, André R. Laplante

Understanding the appropriate gold recovery to associate with copper recovery when assessing laboratory testing on porphyry deposits is often complicated by several factors including variable and/or complex mineralogy, and the variability contributed by the low Au content of the various flotation products. As a result, gold recovery is often underestimated and the value contributed by the gold to project economics is less than it should be, a problem that could influence overall project viability. Typically, for these types of deposits, the gold recovery is found to be lower than the copper recovery. In this unique project, having the objective of seeking a better understanding of gold recovery relative to copper recovery, mill feed samples from a selection of six operating world-class Cu-Au low-grade deposits were collected along with the mill metallurgical results for the corresponding sample periods. The samples were subjected to laboratory flotation tests, as well as the Laplante gravity recoverable gold (GRG) test, mineralogical assessment and cyanidation leaching. The aim was to better understand the copper and gold recovery relationship, the links between laboratory and plant flotation performance, the influence of mineralogical differences, and the potential for enhancing gold recovery by gravity recovery techniques. A new correlation of copper and gold recoveries based on the results is presented in the paper. The results showed that the link between copper and gold recoveries established in the best laboratory tests were maintained in the plant results, and further, that the potential for improving Au recovery by gravity or flash flotation methods is directly proportional to the amount of gold greater than 75 microns.

Jan 1, 2005

By H. Huang, H. M. Chen, W. B. Xie

Cu-0.8Cr-0.1Zr alloy were prepared by atmospheric melting. the microstructure and properties of the CuCrZr alloy after first cold rolled, solid solution, second cold rolled and aging treatment were analyzed by using optical microscope, electrical conductivity analysis and Vickers hardness tester. The results show that with the increase of the first cold rolled deformation, the grain breakage becomes more serious, and the cold hardening becomes more obvious and the hardness increases. The conductivity and peak hardness of the first cold rolled (reduction of 30% and 60%) alloys after solution, secondary cold rolled and aging treatment reaches 81 %IACS and 187 HV, respectively. However, the conductivity in the CuCrZr alloy with a higher rolling degree (reduction of 90%) after solution, secondary cold rolling and aging treatment is significantly higher, and the conductivity and peak hardness is 85.8 %IACS and 178 HV, respectively. INTRODUCTION CuCrZr alloy has been widely used in domestic industry for its excellent comprehensive properties such as high strength and high conductivity, especially in the contact wire and lead frame of high-speed railway (Sun, Tao, & Lu, 2015; Mishnev, Shakhova, Belyakov, & Kaibyshev, 2015; Zhang et al., 2016; Fu et al., 2017). In recent years, a lot of research has been done on how to improve the strength and conductivity of CuCrZr alloy. However, the high strength and high conductivity of copper alloys are contradictory characteristics. On the one hand, the addition of alloying elements is conducive to solution strengthening and aging strengthening; on the other hand, too much alloying elements in copper alloys cause defects in the lattice of copper matrix, resulting in a serious decline in the conductivity of copper alloys (Martienssen & Walirmont, 2005). How to obtain high strength and high conductivity at the same time is the main problem. At present, the main research methods are adding microalloying elements, thermomechanical treatment and severe plastic deformation to study the electrical conductivity and mechanical properties of CuCrZr alloys. For example, Xie et al. (2011) added trace Ag to the Cu-0.26 wt%Cr-0.08 wt%Zr alloy, and the size of precipitated phase Cr and Cu4Zr became smaller and the mechanical properties of the alloy were improved. Su, Dong, Liu, Li, & Kang (2004) found that the addition of trace Mg in CuCrZr alloy inhibits the growth of precipitated phase and reduces the internal stress around the precipitated phase. At the same time, the size of precipitated phase becomes smaller and the peak aging strength of the alloy is improved. Pang et al. (2013) found that adding trace Ni and Si to the CuCrZr alloy could improve the peak hardness, softening resistance and precipitation morphology of the alloy. Experiments shows that the grain size was significantly refined by equal channel angular extrusion combined with aging treatment, while the strength of the alloy was increased, and the electrical conductivity of the alloy did not decrease (Vinogradov, Patlan, Suzuki, Kitagawa, & Kopylov, 2002; Saray, 2016); Kermajani, Raygan, Hanayi, & Ghaffari (2013) showed that the strength of CuCrZr alloy can be improved by rolling at 500 °C. After 150 minutes of aging treatment, the strength and conductivity of the material increased to 431 MPa and 81 %IACS, respectively. Takata, Ohtake, Kita, Kitagawa, and Tsuji (2009) noted that the strain hardening, uniform elongation and tensile strength of the nano-precipitates produced by the mechanical heat treatment process can be notable enhanced. The mechanical and electrical properties of CuCrZr alloy can be improved by combining large plastic deformation with aging treatment in the test process (Gao, Huttunen-Saarivirta, Tiainen, & Hemmila, 2003; Huang et al., 2003; Xia et al., 2012; Zel’dovich et al., 2014).

Jan 1, 2019

By T. Lamb

There are many honor stories about aluminum in the marine environment and many are not based on facts, so they are myths. Myths must be addressed before progress can be made. This paper attempts to dispel the myths and state the facts. A common perception is that aluminum ships cost significantly more than steel ships. This paper illustrates that even though the cost of the aluminum structure is over 50% more than the steel structure, an "equivalent" aluminum naval ship can be built within 7% of the acquisition price of a steel ship. This is possible because of the cascading benefits of the aluminum ship's significantly lighter weight. Aluminum ships also have a life-cycle cost advantage over steel ships because of reduced maintenance and fuel cost savings.

Jan 1, 2011

By Nicolae Dobritoiu

The literature in this field and the practical activity record that a method, respectively the technology used for an underground mining work have many components which, in order to be applied, demand that for each of the parameters that describe the environment of the mining work and that influence the chosing of that method and that technology of execution, must have values in an interval well determined. There are situations when one or many parameters of the set of parameters that describe the environment of the mining work, can modify its values, and, as a result, one or more components of the methods or technology cannot be applied anymore, making necessary a replacement of their values. The information offered by this graphical-analytical model allow the determination of optimum solutions for the process of digging of the underground mining work and thus it will result the incresing of the technical-economical efficiency of the digging process and, also the increasing of the quality of the underground mining work.

Oct 1, 2009

By Ben Bradshaw

Context ? Community engagement has become an increasingly significant and challenging part of mineral exploration and mine development; indeed, opposition from communities proximate to a proposed mine site has been known to derail technologically- and financially-sound projects. ? These cases suggest that mining firms need to better understand how to engage constructively with local communities in the pursuit of their claims. ? While a range of publications exist promoting various community engagement strategies, these recommendations, when viewed as a whole, are disjointed and largely untested in real development contexts. Aims of Presentation 1. Synthesize industry, NGO, government and academic publications focused on community engagement best practice in order to highlight those practices that are most commonly recommended. 2. Review the (Canadian) mining industry?s experience with some of these strategies based on existing case material in order to identify the extent to which commonly prescribed strategies are used and validated in practice.

May 1, 2010

By E. Wolmarans

The selection of the main mineralised zone (MMZ) concentrator milling circuit has followed a comprehensive route over the preceding 10 years. Many knowledgeable parties have contributed and assisted in developing the milling circuit according to the best available information. The final selection of the flow sheet was completed after DRA conducted a techno-economic study on four possible comminution circuits ranging from conventional crushing and ball milling to fully autogenous (AG) milling. The results from all the above mentioned work indicated that it is possible to treat the MMZ ore at the desired throughputs to the desired grind sizes in a fully autogenous grinding circuit. The flow sheet was designed to treat the main mineralised zone (MMZ) arising?s from both underground and open cast operations and incorporates a fully autogenous grinding (AG) circuit. Commissioning of the 375ktpm concentrator at Nkomati Nickel began in August 2009 with the first ore reporting to the mill on the 15th of September 2009.

Jan 1, 2012

By C. H. Dionne, J. A. Holmes, B. J. Huls

"Falconbridge Limited is presently developing flowsheet alternatives for implementation at the Strathcona Mill. The main thrust for change arises from the need to reject more pyrrhotite from the concentrate. To maintain appropriate levels of sulphur in the smelter concentrate, however, enhanced removal of non-sulphide gangue minerals must be realized. This could best be done in the Non-magnetics flotation circuit.Laboratory investigations were followed by an on-stream pilot test at Strathcona. The application of a column cleaner on the Non-magnetics concentrate resulted in significantly lower levels of fine gangue at equivalent sulphides recovery.This paper discusses the laboratory and pilot testing and results, with a focus on piloting. Also included is a discussion of the Strathcona Mill Flowsheet and the role of the Nonmagnetics flotation circuit.INTRODUCTIONFalconbridge Ltd. is currently developing means to reduce atmospheric sulphur dioxide emissions. One alternative is a reduction in the amount of pyrrhotite in Strathcona Mill concentrate, which reports to the smelter. Pyrrhotite in the Falconbridge ores contains an average of 39 percent sulphur and 0.64 percent nickel. By comparison, pentlandite contains an average of 33 percent sulphur and 34 percent nickel.A consequence of the rejection of pyrrhotite is a decrease in the sulphur assay in the remaining concentrate. This decrease causes downstream difficulties in the roasting process. Therefore, the content of non-sulphide gangue in the mill concentrate must also be reduced in order to maintain sulphur grades adequate for roasting. The resulting concentrate will have lower sulphur dioxide emissions while maintaining nickel production."

Jan 1, 1991

The Cadia mine is shifting from the open pit operation to the Cadia East underground block cave. The resulting increase in milled tonnes and the decrease in fines production through shifting to block caving require an increase of over 25% in installed power. This expansion is being accomplished via the installation of up-front crushing and HPGR milling of the ore, with the SAG mill receiving a secondary crushed feed. This design, criteria and rationale for selection is presented. Over the coming years, the mine will further expand capacity. The target is to accomplish this with minimal addition of installed power or use of fresh water. This presents a challenge that epitomizes the future constraints on our resource dependent and intensive industry. The approach and proposed options to this longer-term expansion are also presented.

Jan 1, 2012

By Dave Bulled

"This paper describes the design of a molybdenite flotation circuit using FLEET technology applied to kinetics data produced from laboratory flotation testing and distributed across the blocks of a mine plan using a geostatistical approach. The geostatistics assigned the statistical error that arises from having a limited amount of sample testing data to the kinetics estimates of each block of ore in the mine plan. The final design then included a quantification of risk based on the accuracy of the block flotation kinetics and model fitting. The design made reference to the extensive technical reports describing earlier metallurgical test work including some pilot plant work over thirty years ago.The testing involved conducting MinnovEX Flotation Tests (MFT) to determine the rougher flotation kinetics at the specified reagent conditions and rougher-cleaner tests to determine the change in kinetics resulting from regrind. These flotation kinetics were used within FLEET simulations to create a full-scale flowsheet and plant design including recommended equipment sizes and the forecast of operating results. Measurement of detailed flotation kinetics for a wide range of samples allowed the effect of size of grind and efficiency of classification (i.e. width of size distribution) to be predicted for the whole ore body.INTRODUCTIONAdanac Moly Corp. proposed to develop a 20,000 ton per day mill to produce high quality molybdenite concentrate from its Ruby Creek resource in north-western British Columbia. It is a relatively clean low grade porphyry-monzonite occurrence containing minimal quantities of other sulphides such as chalcopyrite, pyrite, sphalerite and galena. Molybdenite occurs mainly as coarse flakes with lesser amounts of finer sized values. An optimum plant design was required to can achieve the predicted operating results, at a known level of risk, while treating the variability inherent in the ore body."

Jan 1, 2007

By Chr. Krause

Within the scope the collaborative research centre 599 (Medical University of Hanover, University of Veterinary Medicine Hanover, University of Hanover) the behaviour of the degradation of magnesium materials as implants are investigated by using animal experiments (rabbits). Thus extruded cylindrical pins from the magnesium alloys MgCa0.8%, WE43 and LAE 442 were implanted intramedullary in the tibiadiaphyses. The implantation duration was 3 and 6 month. After the explantation 3 point bending tests were carried out to investigate the possible changes of the mechanical properties. Clearly changes in dependence of the implantation duration could be determined. The three magnesium alloys show a decrease of the mechanical resistance with an increasing implantation time. To evaluate the degradation process, wich is the reason for the changes, micrographs and element analyses (EDX) have been accomplished after the 3 point bending tests. The micrographs show for all used magnesium alloys corroded surfaces but no preferred corrosion on the grain boundarys. The element analyses show beside a layer which is rich in calcium and phosphorus an agglomeration of rare earth elements in this layer. With these results a using of magnesium alloys as a material for implants can be announced.

Jan 1, 2006

By Henri-Loui Jacob, Suzie Nantel

"Depuis la fin des annees 1800, la province de Grenville represente pour Ie Quebec une source importante et diversifiée de minéraux industriels. Le Ministère de l'Énergie et des Ressources du Québec, dans Ie cadre de I'entente auxiliaire Canada-Québec, et les compagnies minieres y ant multiplié, surtout depuis 1983, leurs travaux d 'exploration, de cartographie, et d'évaluation pour les minéraux industriels. Ces travaux ant conduit ala découverte et ala mise en valeur de gisements de granite architectural, de graphite, de dolomite et ant aussi permis de repertorier des gîtes et des indices prometteurs de wollastonite, de silice, de calcite. de dolomite, de silicates d'alumine et de terres rares. Les gisements récemment découverts sont actuellement exploités au sur Ie point de l'être et les gîtes et les indices les plus prometteurs ant été jalonnés.ABSTRACTSince the late 18oos, the Grenville Province in Québec has been an important and diversified source of industrial minerals. The Ministere de l'Énergie et des Ressources du Québec, under the Canada-Quebec Mineral Development Agreement, and the private sector have put an emphasis on exploration, mapping and evaluation programs in the Grenville Province for minerals, particularly since 1983. These programs have led to the discovery and the development of deposits such as architectural granite, graphite and dolomite, and have also led to inventories of occurrences and prospects of wollastonite, silica, calcite, dolomite, alumina silicates and rare earths. The deposits discovered lately are presently being quarried or will be in the near future. The most promising occurrences and prospects have been claimed."

Jan 1, 1990