Search Documents

By F. Khomamizadeh

In this study, deep cryogenic treatment was applied to A319 cast aluminum samples. Although the cryogenic treatment didn't have any significant effect on mechanical properties of the well degassed and fluxed samples, but the tensile strength of the samples containing a considerable amount of gas and shrinkage defects was improved surprisingly, This improvement was attributed to the strengthening of the a-aluminum matrix which slows down the propagation of the existing defects. There was no significant increase in the hardness after cryogenic treatment, The abrasion resistance of the alloy was improved after cryogenic treatment, by developing a homogeneous protector shield, composed of abrasive grains penetrated into the soft aluminum matrix and kept tight.

Jan 1, 2005

By L. W. Vollmer

Introduction During the past three years at least fifty strings of 9% nickel steel tubing have exhibited excellent resistance .to the variably severe corrosive conditions typical of many of the sweet condensate wells in Mississippi, Louisiana, and Texas. This experience, and the characteristically outstanding performance of other ?nickel alloy steels under hydrogen sulphide corrosive conditions, dictated the selection of 9% nickel steel tubing for the second well drilled in the sour condensate Pincher Creek field of southwestern Alberta. The damaging effects of the Pincher Creek reservoir fluids on well equipment had been manifested in the discovery well by the rapid and not yet fully understood failure of API Grade N-80 tubing, stainless steel wire lines, and alloy steel fishing tools. Two very unexpected failures in the 9% nickel steel tubing, after only six days of service in production tests, instigated an extensive and continuing investigation to ascertain the probable cause of failure. This discussion presents some of the results obtained thus far which cast a little light on the perplexing behaviour of steels in hydrogen sulphide environments in general, and in sour condensate wells in particular. History of Tubing Failures Walter Marr well No. 1, in which the 9% nickel steel tubing failures occurred, produces from the Madison lime at the depth interval approximately 12,200 to 12,750 feet. The gas-oil ratio is about 26,000 and the gas contains 10.2 per cent hydrogen sulphide and 6.3 per cent carbon dioxide by volume.

Jan 1, 1952

By Jason Rrno

The emergence of Impact and Benefit Agreements (IBAs) in the Canadian mining sector has been read by many as a positive governance innovation. Negotiated directly between mineral resource developers and Aboriginal communities with limited government interference, IBAs serve to manage impacts associated with a mining project and deliver tangible benefits to local communities. Notwithstanding their increasing use and significance, limited systematic analysis has been undertaken to determine whether they are, in fact, working. This paper reports on the effectiveness of a number of IBAs negotiated in support of three northern Canadian diamond mines, drawing on evidence from time-series data, key informant interviews, and focus group meetings in Yellowknife and Dettah, NWT, and Kugluktuk, NU. While some deficiencies were apparent and perceptions of effectiveness varied somewhat by Aboriginal community, the IBAs were generally found to be meeting their objectives, especially with respect to the delivery of benefits. For Aboriginal communities affected by mineral development in the Canadian North, this represents a significant change to typical outcomes of the past. Moving forward, research on IBA effectiveness needs to adopt a longer timeframe and begin to gauge the degree to which IBAs are able to address long-standing concerns associated with hinterland resource extraction beyond their agreement-specific objectives.

May 1, 2010

By B. Stettner, J. Asante, S. Abraham

The levels of nitrogen in steel produced in various metallurgical vessels vary significantly. For example, the tap nitrogen levels in steel produced in the BOF are around 4Oppm, as compared to 70-100ppm in both DC and AC electric arc furnaces. Given the pressing need to reduce nitrogen levels in steel to satisfy customer demand, IPSCO Inc. has gained considerable experience in controlling nitrogen levels in steel over the course of the last three years. Hence, a cost effective process has been developed through an intensive nitrogen control program from steel melting in the EAF through to the continuous slab casting stage. This paper describes the practices employed at each stage of the steelmaking process that have enabled IPSCO Inc. to reduce and control nitrogen levels in steel.

Jan 1, 2004

By P. Rosario

"Current industry practice for HPGR assessment and sizing relies on conducting a series of tests using pilot-scale machines with roll diameters of 700 mm to 1000 mm. Substantial amounts of sample are required for such pilot test programs, typically 1 to 10 tonnes of the sample is needed depending on the level of study and complexity of the resource. Collection of large quantities of representative samples during the early stage development is challenging and expensive, thus significantly hinders the HPGR technology from being incorporated into early-stage designs. A robust and reliable laboratory test is therefore needed to allow a fair consideration of HPGR for early stage projects. With support from the Canadian Mineral Industry Research Organization (CAMIRO), the NBK Institute of Mining Engineering at the University of British Columbia (UBC) developed a suite of Piston Press bench-scale tests that correlated to pilot and full scale HPGR operating information (Davaanyam, 2015; Davaanyam et al, 2015; McClintock, 2018). The Piston Press Tests (PPTs) are capable of assessing the HPGR technology at the scoping, pre-economic analysis (PEA), and pre-feasibility (PFS) stages of project development. This paper will briefly describe the theory on which the PPTs are based, and then presents a case study conducted for a copper deposit to show how the PPTs are being used for scoping and pre-feasibility level studies. Specifically, the PPTs are being used to provide information for preliminary sizing and selection of an HPGR and to assess the effect of ore variability on HPGR performance. The results are also applied to developing HPGR circuit designs and can be incorporated in simulation so that optimum design parameters can be selected.INTRODUCTION It is widely accepted that high pressure grinding rolls (HPGRs) offer a viable energy-efficient solution for the modern comminution flowsheet design. Table 1 summarizes selected examples of HPGR applications in the hard rock mining industry. The main benefits of HPGRs are energy savings which leads to lower operating costs, and its stable operating characteristics that can better cope with variations in ore hardness when compared to the conventional SAG mill-based comminution circuits."

Jan 1, 2019

By T. Yeomans

NVI Mining’s Myra Falls operation is a forty-year-old underground mining operation feeding a 4,000 metric tonnes per day concentrator. The current mill, built in 1985, was designed to process a massive sulphide ore-body. This orebody, known as the HW, contains about 50% pyrite. Minerals of value are chalcopyrite and sphalerite, with precious metals occurring in all mineral types. By 1997, mining of a new ore-body, known as Battle-Gap, commenced. Mineralogically complex, the new orebody contains about 15% pyrite copper minerals, including primary chalcopyrite and secondary bornite, chalcocite and tennantite, combined with increased galena and sphalerite. Flotation performance generally decreased with increasing amounts of Battle-Gap ore types, with both copper concentrate quality (increased lead and zinc content) and copper recoveries being affected. Following significant metallurgical test-work, a new, fully sequential copper-lead-zinc flotation flow sheet and reagent scheme was developed. This sequential flow sheet was progressively installed and commissioned during 2006. Copper concentrate lead and zinc smelter penalty contents have been reduced by some 40%, while increasing copper recovery by 10%.

Jan 1, 2009

By G. Knight

"Results of a program of dust research carried out at the Mines Branch Laboratory, Elliot Lake, indicate that dust-concentration estimates vary greatly, depending on the sampling instrument, the assessment technique and the properties of the dust cloud. The wide range of the ratio between the estimates by any pair of instruments shows that the correlation between the health hazard and dust-concentration estimates by most existing sampling instruments must be questionable. Important studies are being carried out to permit the definition of mine environments in more precise technical terms. The influence of size selection, the physical property measured, composition and sampling period on the assessment of the health hazard are discussed."

Jan 1, 1969

By Ted J. Williams

Underhand cut and fill mining methods are used at the Lucky Friday, Stillwater, and Galena mines in the western US in an effort to safely mine in difficult ground conditions and as a primary mining method where access below the ore is limited. The method has evolved at each mine to meet the unique situations associated with their milling procedure and mine layout. Details of the operational aspects of the backfilling and mining cycles at each mine are presented in this paper, accompanied by a summary of the mechanical properties of the backfill and its in-situ geomechanical behavior.

May 1, 2007

By Eugene Barsky

"At present, theoretical concepts of gravitational separation processes are mainly limited by the study of the interaction between a flow and a solitary particle. Then the main conclusions of this analysis are applied to a mass process. However, this analysis is absolutely insufficient, because some elementary phenomena such as the ingress of coarse particles into the fine product output and vice versa cannot be interpreted from its standpoint. It is also impossible to predict the results of the classification of a material with a specific granulometric composition on a specific apparatus on its basis.In the present paper, an extended model of the process is suggested. The model is based on the behavior of all the particles of a specific narrow size class, and not on that of an individual particle. Similarity criteria of the process, which were empirically derived previously, are obtained from the analysis of this model.INTRODUCTIONIn case of gravitational separation, a part of solid phase moves, as a rule, vertically upwards with the flow, while another part settles against the flow. This flow is extremely complicated and chaotic due to various random factors. Among these factors are mass interactions of particles with each other and with the apparatus walls, non-uniform character of concentration and velocity fields, turbulent vortices and local fluctuations, real particles shape difference from spherical one, etc.Particles rotation results in a transverse force (Magnus' effect). At the motion of a non-rotating particle in a non-uniform velocity field, a transverse force also arises (Saffman's effect).A great number of publications have been devoted to the account for all these factors in two-phase flows in recent decades. Very complicated models have been developed, but the problem has not been completely solved as yet [1, 3].At the same time, simplified models of the behavior of a solitary particle in a flow are being developed. Despite their schematic nature, such models often prove to be useful for establishing general laws of the process and its similarity criteria [1]."

Jan 1, 2016

By Ron Board

"Probably the only thing that can he said about conveyor belt scales without fear of contradiction is that they have been responsible for as much or more puzzlement, argument and frustration than almost any other piece of equipment commonly found in ore processing facilities. To be sure, there are certainly a good number of satisfactory installations, some of these having been achieved through forethought and careful consideration in the early stages of plant design, while others seem to owl their success to what seems to be little more than good luck or white witchcraft; and it might also appear that black witchcraft or other gremlins are solely responsible for the poor performance of many belt scales that enjoy well-designed installations with apparently good operating conditions.This paper is intended to acquaint users with the major operational reasons why belt scales seem so fickle (and downright ornery too), and establish some reasonably simple test standards against which the performance of scale hardware can be measured. Then it shall be shown how the design flexibility of electronic scale systems can offer particular advantages in overcoming some of these everyday problems in a practical way, and without undue inconvenience to plant operations."

Jan 1, 1975

By T. R. Raponi

"The Williams Mine, Canada's largest gold mine, processes over 6,000 t/d of ore utilizing SAG/ball milling, leaching and CIP, carbon stripping, electrowinning and refining to produce gold dare bullion.Grinding accounts for over 50% of milling costs with grinding media, power and mill liners making up over 75% of grinding costs. Since 1991, several changes in these areas have been made which have significantly reduced costs, while fineness of grind and mill recovery have both been increased.This paper discusses the changes made in the grinding circuit over the past few years and assesses their impact on operating costs and mill operations.IntroductionThe Williams Mine is located in the Hemlo area of northwestern Ontario, about 40 km east of Marathon. It is operated by the Williams Operation Corporation, which is equally owned by Teck Corp. and Homestake Canada Inc. Canada's largest gold mine, the Williams Mine commenced operation in October 1985 at a rate of 3, 000 t/d. Mill throughputs have typically exceeded design, averaging 3, 397 t/d in 1986, and 3,380 t/d in 1987. In August 1988, production was increased to 6,000 t/d. Throughput averaged 4,212 t/d in 1988. Production increased over the next few years averaging 5,477 t/d in 1989, 6,248 t/d in 1990, 5,987 t/d in 1991, and 6,283 t/d in 1992. With a recovery of over 95.5%, production for the first three quarters in 1993 is averaging 6,408 t/d.GeologyThe main ore body is a steeply dipping conformable zone of microcline-quartz-muscovite rock. It occupies the contact zone between hanging wall metasedimentary rocks and foot wall felsic quartz feldspar porpyritic rocks of possible volcanic or subvolcanic intrusive origin. The ore body is enveloped by muscovite schists which are thickest on the footwall side. The schist is enriched with tourmaline, pyrite, and green mica containing vanadium and barium. The ore body contains pyrite and barite which occurs mostly in laminae and bands to veinlets and breccia fillings. The gold occurs as free (native) grains, 20 to 30 µm in size at grain junctions of the microcline and quartz. Visible gold is rare in the main zone. There are commonly two or more discernable layers of economic value which are separated by weakly gold mineralized material which usually consists of muscovite schist, barite rich zones or sulphide poor-microcline-quartz rock and in the upper and western fringes by biotite rich schist with feldspathic fragmental characteristics. Molybdenite is a common constituent as very fine disseminated grains in the microcline-quartz rock and is most prominent with gold enrichment. Stibnite and realgar are two of the more common accessory sulphides."

Jan 1, 1994

The importance of understanding the behaviour of cemented paste backfill (CPB) within the framework of the effective stress concept is highlighted in this paper. Only through an understanding built on this concept can problems such as barricade loads, the rate of consolidation and arching, be fully understood. The critical importance of the development of stiffness during the hydration process, and its impact on factors such as barricade loads, is used to illustrate why conventional approaches that implicitly ignore the effective stress principle are incapable of capturing the essential components of CPB behaviour.

May 1, 2007

By Al Goodier

"This paper discusses the experience of Noranda Mines Limited, Matagami Division, with the vertical crater retreat (VCR) method in the mining of narrow-vein stopes. Although limited to only one stope, the viability of this method at the Radiore No.2 Mine has proven that further use of VCR in narrow-vein mining will be made.IntroductionThe Radiore No.2 property is located east of the Bell River in the southeast quadrant of Isle-Dieu Township, approximately 4.5 km east of the town of Matagami. The new James Bay Highway is 2.5 km north of the property and access to the mine is by a 2.5-km logging road.The property was staked by Radiore Uranium Mines in March 1961 and the sulphide body was first indicated by an E.M. survey. Diamond drilling commenced in the fall of 1961 and was completed by the end of 1962. As per an agreement in 1970, the claims were sold and assigned to Orchan Mines Limited. Subsequently, the property was transferred to Bell Allard Mines Limited, a wholly owned subsidiary of Orchan Mines. Early in 1979, Noranda Mines Limited acquired the property and it is now part of Noranda's Matagami Division.Geology and MineralizationThe deposit is in a band of volcanic rocks north of the Bell River complex. The lens of massive sulphides dips almost vertically and strikes almost east-west. The north contact is essentially sharp against andesite material; the south contact is less well defined, as the massive sulphides tend to grade into more disseminated material.The orebody varies from 5 to 20 feet in width, by 350 feet long and 200 feet in height. The overburden is composed of sand, gravel and clay, varying from 0 to 26 feet in depth. The ore reserves were 153,340 tons grading 1.97% copper and 1.01% zinc including 10% of dilution at zero grade."

Jan 1, 1982

By Hossein Aminian, Daniel Hodouin, Claude Bazin, Claude Jacob

"Solvent extraction followed by electrowinning (SXEW) is an economical option for the processing of low grade and oxidized copper ore. Phenomenological models were developed to simulate the copper solvent extraction and the electrowinning processes. The two models were linked together to make a SX/EW simulator. The simulator is used to predict the operation of the mines Gaspe pilot plant put in operation in 1996. Results confirm the potential of the simulation that would subsequently be used for student training, process optimization and to assess the performances of control strategies.INTRODUCTIONSolvent extraction followed by electrowinning (SXEW) has become in the last two decades a key process for the recovery of copper from solution obtained by leaching low grade copper ore. Several operations have been commissioned in North and South Americas in the last decade (Arbiter, 1994). In Canada, Gibraltar Mine (Scott, 1991) operates a SX plant followed by electrowinning (EW) to produce copper cathode from leached low-grade ore dumps. From 1996 to 1997 Mines Gaspe operated a pilot plant to test the economical feasibility of leaching an oxidized copper ore, followed by solvent extraction and electrowinning of copper. Despite copper SX/EW processes have the reputation of being low cost operations, plant engineers should always look at way to make the plant more efficient. Process models provide an economic platform to learn, control and ultimately optimize the operation of a plant.Several models have been independently proposed to simulate the SX process (Cadman and Hsu, 1970; Medina Gomez, 1980; Wilkinson and Ingham, 1983; Garcia et al., 1988; Aminian et al., 1997) and the EW process (Bryson, 1981; Barton and Scott, 1992; Barton and Scott, 1993). However few papers, if any, deal with the integration of the two process models into a single simulator of a SX-EW plant. This paper describes the development of an integrated simulator for the SX-EW process and shows some steady-state simulation runs of an actual SX-EW pilot plant. The paper consists of four sections. The first section shows the general layout and principles of operation of a SX-EW plant.The second section describes the SX model while the third section deals with the process model used for the copper electrowinning process. The last section shows how the two process models are linked to simulate the operation of the Gaspe pilot plant."

Jan 1, 1999

By Les Johnston

_ BACKGROUND - About EPCOR - Genesee Generating Station - Phase 3 Expansion _ TECHNOLOGY SELECTION - Selection Criteria - Combustion Options - Flue Gas Emission Control Options _ STAKEHOLDER VIEWS _ PROJECT STATUS _ EPCOR is an integrated utility company for water, gas, electricity and technology services. _ EPCOR has about 1.6 million customers in Alberta, Ontario, Manitoba, BC, and the U.S. Pacific Northwest. _ EPCOR Generation Inc. operates three power stations in Alberta which were in operation before deregulation, including the coal-fired Genesee Generating Station. _ EPCOR Power Development Corporation owns generating stations in Alberta, BC and Washington State and will be building the Genesee Phase 3 expansion.

May 1, 2002

By E. V. Neelands

THE Canadian Malartic mine is in Western Quebec, about fifty miles east of Noranda and forty miles south of Amos on the Canadian National railway. The recently constructed branch of the railway from Rouyn to Senneterre passes half a mile north of the mine. HISTORY he property was discovered in 1923 'by St. Barbe Sladen, H. S. Kennedy, and J. C. Carroll, who were prospecting for an Ottawa syndicate and found gold in a small quartz vein near the present workings. Five claims were staked and were optioned to an exploration company, who allowed the option to lapse after surface sampling and diamond drilling eighteen holes. Some months later, the property was sold to Malartic Gold Mines, Limited, who carried on development until 1929. A vertical shaft was sunk and exploration work done on three levels, supplemented by diamond drilling 16 surface holes and 62 underground holes. The work indicated that the important ore occurred in two silicified.zones in schisted greywacke which intersected west of the shaft and were believed to be controlled by a drag-fold. The ore grade was not considered sufficiently favourable to war-rant an operation, and work was terminated. With the advance in the price of gold to $35 per ounce, interest was revived and a new Company, Canadian Malartic Gold Mines, Limited, was incorporated for further development. The shareholders of the old Company accepted a new position under which their interests were protected, and sufficient treasury shares were optioned to Ventures, Limited, and Sudbury Basin Mines, Limited, to provide funds for further exploration of the prop-erty to determine whether, under the new economic conditions, profitable operation would be possible, and, if advisable, to provide the equipment for production. Additional claims were acquired, bringing the total area up to 1,029 acres.

Jan 1, 1939

By Walter I. Nelson

THE geology of the Copper Mountain mine has been ably described by Dr. Victor Dolmage in Memoir 171 of the Geological Survey. Reference is invited to that paper for a more extended description of the geology of the ore deposits than will be given here. The important orebodies of the mine occur in fragmencal volcanic rocks, parallel with and adjacent to the gabbro of the Copper Mountain stock. In the mine area, the contact strikes N.45°W. and dips either vertical or steeply co the southwest. For a distance of 500 feet or more from the contact, the fragmental rocks have been intensely metamorphosed both dynamically and hydrothermally. The dynamic effects are reflected in the foliation and fracturing parallel with the contact, which occurs throughout the mine, and the volcanic rocks within this foliated zone are, in places, highly schistose. Superimposed upon thi.s structure is a system of fine, straight, parallel frac-tures that strike nearly normal to the foliation (and contact) and dip between 65° and 75° to the north; it is with this last-described fracture system that the ore minerals are structurally associated. The fractures are mineralized with bornite and, to a considerably less extent, with chalcopyrite and some pyrite. A notable characteristic is the extreme fineness of the fractures; even in high-grade ore they are rarely larger than pencil lines. The tenor of the ore, therefore, varies directly with the fracture spacing. Replacemcnr of the host-rock between two or more fractures, varying in degree from finely disseminated sulphides to masses of nearly solid bornite up to 18 inches wide and 2 to 3 feet long, is not uncommon in the higher-grade portions of the orebodies. Two structural types of orebody are recognized in local nomenclature: the 'contact' orebodies, so-called because they occur along the contact; and 'outlying' orebodics, which are enclosed in the volcanics. The former arc tabular or lenticular bodies elongated along the strike and dip of the contact. The 'outlying' orebodies are coniform, chimney-like masses roughly elliptical in plan; with depth, their roots plunge at steep angles toward the contact. All of the orebodies are cut by a number of light-coloured granophyre and felsite porphyry dykes. These dykes-the so-called 'mine' dykes -enter the mine area from the north, curve gently southeasterly across the orebodies, and then cross the contact into the gabbro at the south end of the mine. All the dykes dip vertical to steeply east.

Jan 1, 1941

By V. Baboudjian, R. J. Geren, J. Thiriar

"The electrolytic tankhouse at CCR was recognized by management as lagging behind modem refineries in terms of productivity, energy efficiency and controls. The operation was also burdened by high maintenance costs of cells, floors and electrolyte recirculation systems.A bench marking program was started in 1986 to evaluate processes and other technology by visiting major copper refineries in North America, Europe and Japan. The basic principles necessary to optimize the operation were defined, and a program calledCCR 2000 was prepared for approval of the necessary capital investments.This paper describes the results obtained to date and outlines the remaining work to complete the modernization program, in particular, the control of electrolytes, the elimination of the Baltimore groove and studies to modernize the stripping operation or adopt permanent cathode technology.IntroductionThe CCR Refinery of Noranda Copper Smelting and Refining (Noranda Minerals Inc.) , in Montreal East, is one of the world 's largest custom copper and precious metal refineries with a capacity to refine 350000 tonnes of copper per year. The silver refinery, which treats the copper tankhouse anode slime, foreign slime and precious metal ingots, produces 800 000 kg of silver, 26 000 kg of gold and 3800 kg of platinum-palladium concentrate annually. Copper anodes are received from the Horne Smelter at Rouyn-Noranda, Quebec, and Mines Gaspe Division in Murdochville, Quebec. CCR also refines anodes from Hudson Bay Mining and Smelting Co. Ltd. in FIin Flon, Manitoba, and remelts anode scrap along with blister and purchased copper scrap ."

Jan 1, 1993

By Fabian Mohr

The methyl substituted binuclear cyclometallated gold(I) complexes [Au2(?-n-MeC6H3PPh2)2] [n = 4, 5 and 6] all undergo oxidative addition reactions with halogens and, in the case of the 4- and 5-methyl substituted analogues, with dibenzoyl peroxide to give metal-metal bonded digold(II) complexes [Au2X2(?-C6H3-n-MePPh2)2]. The 4- and 5-methyl substituted digold(II) compounds on warming or exposure to light undergo carbon-carbon coupling reactions to give gold(I) complexes containing the corresponding 2,2'-n,n'-biphenylyldiphenylphosphines. The 6- methyl substituted digold(II) complexes rapidly isomerise above ca. -20° C to binuclear heterovalent gold(I)/gold(III) compounds [XAu(?-2-Ph2PC6H3-6-Me)AuX{?2-(6-MeC6H3-2-PPh2)}], containing a fourmembered cyclometallated ring on a gold(III) centre. Surprisingly, no carbon-carbon coupling could be induced for any of the 6-methyl substituted compounds, even under forcing conditions. This difference in reactivity of the 6- methyl derivative, compared to that of the 5-methyl and unsubstituted analogues was studied by ab initio calculations using a series of model compounds. The results are in excellent agreement with the experimental findings and suggest that the key-step in the C-C coupling reaction is the partial opening of the Au(III)-P bond in one of the transition states. In the 6-methyl system this transition state is energetically inaccessible and hence no C-C coupling occurs.

Oct 1, 2003

By D. J. Thorkelson

New data indicate Wernecke Breccia-associated iron oxide copper-gold (IOCG) deposits likely formed from moderate-temperature, high-salinity, non-magmatic brines. The breccias formed in an area underlain by a sedimentary sequence that locally contained evaporites (potential source of chloride and possibly sulfur) and was thick enough to produce elevated fluid temperatures. Metals (Fe, Cu, Co, U) were probably derived from host strata, transported as chloride complexes, and precipitated due to changes in fluid temperature and pressure during brecciation. These new data suggest that the spectrum of genetic models for IOCG deposits that typically invoke formation from magmatic or hybrid magmatic-non-magmatic fluids should be expanded to include those systems that formed in a non-magmatic environment. Modifications to the definition of IOCG systems are proposed that reflect the degree of involvement of magmatic and/or non-magmatic fluids and the nature of the mineralizing environment. A division into magmatic, non-magmatic, and hybrid magmatic-non-magmatic IOCG types is suggested. Typical magmatic end-member IOCG deposits include Lightning Creek and Eloise, Australia. Hybrid magmatic-nonmagmatic IOCG examples include Ernest Henry and Olympic Dam, Australia. The Wernecke Breccia and Redbank deposits are suggested as possible representatives of non-magmatic IOCG end members. Endmember magmatic IOCG deposits have similarities to some porphyry deposits, whereas non-magmatic IOCG end members share characteristic with some sediment-hosted Cu deposits, suggesting that the range of IOCG deposits may form a link between intrusive- and sediment-related deposits

Jan 1, 2007