Search Documents

By A. F. Brock

Introduction During the past ten years, shaft sinking has been going on continuously at Inco and new shafts and shaft extensions have been sunk under a broad diversity of conditions. The Murray mine and the Stobie section of the Frood-Stobie mine have?been opened and a main hoisting and supply shaft has been sunk at each of these mines; No. 2 shaft at Murray was sunk initially from surface to 1,960 feet and is now being extended; No. 7 shaft at Stobie was sunk from surface to 3,105 feet. No. 2 shaft at Garson has been extended from 2,200 feet to 3,200 feet in depth. At Levack, No. 2 shaft is being extended from 1,860 feet to 2,850 feet for ore hoisting from the 2,650 lev el. At Creighton, No. 6 shaft, collared on 52 level, was sunk 1,740 feet to a total depth of 5,563 feet below surface. It is the deepest Inco working. At Creighton, also, No. 7 shaft is being sunk from surface to the 30 level to handle the ore from caving operations. Ail Inco main hoisting and supply shafts sunk during the past twenty years have been vertical rectangular shafts equipped with two cages and two ore skips. The cages are standard and interchangeable for all shafts except Garson No. 2; they are single-deck, 13 ft. 4 in. by 5 ft. 2 in. inside and are designed to carry a maximum material load of 16,000 lb. The man load is 48 men. Skip capacities at the several shafts vary from 8 to 15 tons. Forty-two hundred feet bas been established as the standard vertical lift, and the permanent hoisting equipment at each shaft is designed for eventual hoisting from that depth.

Jan 1, 1950

By Gérald Riverin, Bernard Salmon, Marlo Gagnon, Réemi Asselin, Alain Cazavant, Michel LaBrie

"The Ansil deposit is located in the Noranda mining camp in the southern part of the Abitibi greenstone belt. /twas discovered in 1981 and production began in 1989 with proven reserves of 1.58 Mt grading 7.2% copper, 0.9% zinc, 26.5 glt of silver and 1.6 glt of gold. It is centered at a depth of 1.3 kilometre and represents one of the deepest ore discoveries ever made from surface.The deposit consists of a single massive sulphide lens located at the contact between the Northwest Rhyolite and the Rusty Ridge Andesite. The lens strikes north-south and dips 50° east. The thickness of the lens may reach up to 35 m and can change very abruptly both along strike and along dip. The maximum thicknesses of the sulphide lens are reached in its upper (western) and at its lower (eastern) edges, thus giving the deposit its present shape of two sulphide domes connected by a thinner central portion. The lower dome is underlain by a thick accumulation of massive magnetite which may reach 10 to 15m in thickness. The upper and lower domes are underlain by two distinct pipe-shaped zones of stringer and disseminated sulphides which merge with a larger stringer zone at depth.The Ansi/ deposit displays strong relationships between its morphology and the distribution of metals. Hydrothermal alteration consists of chloritization and sericitization. Chlorite alteration is closely associated with stringer sulphide mineralization while sericite is developed in diffuse zones bordering the chloritic zones. Unlike other similar deposits, the Ansil deposit is characterized by very extensive alteration and sulphide mineralization in the hangingwall of the massive sulphides. Several features of the deposit are consistent with an origin from a submarine hydrothermal system which was particularly long-lived, and which thus promoted the build-up of very high fluid temperatures with extensive replacement (and enrichment) of pre-existing sulphides after their original deposition onto the seafloor."

Jan 1, 1990

By Ian Holl, Adam Hempstock, Rickardo Welyhorsky, Niel Morrison

"The Victor Diamond Mine is located in the James Bay lowlands, 90 km west of the First Nations village of Attawapiskat. The project was the first of its kind in northern Ontario and was completed approximately 9 months ahead of schedule.The Victor Mine process plant flowsheet was designed to produce a 95 - 98% by weight diamond concentrate. Main processing steps include 3 stages of comminution, dense medium separation and proprietary x-ray technology for final recovery. Reagent consumption for this process is limited to flocculant, for thickening of fine processed kimberlite, and FeSi for the dense medium separation.The commissioning phase of the Victor Project was executed over a period of 6 months and commenced prior to substantial completion of construction. The approach used was to focus on and complete commissioning of the higher risk dense medium separation and recovery systems prior to construction completion of up stream systems.INTRODUCTIONThe development of the Victor Diamond Mine took place over a period of approximately 5 years and had a capital cost of CAD997 million. It was a greenfields project in an undeveloped region of northern Ontario, only accessible by winter road. Figure 1, below, displays the location of the project within Ontario.The main stages of the project included feasibility, environmental permitting, engineering, construction, and commissioning. At the onset of the engineering phase, the mine was scheduled to enter production in October 2008. Through a team effort between AMEC and DeBeers Canada, the schedule was advanced by 6 months towards the goal of project completion in April 2008. Production status was attained in January 2008, approximately 9 months ahead of the original schedule. This paper focuses on the commissioning aspects of the project and includes a less detailed discussion of the engineering stage."

Jan 1, 2010

By William Ferguson, Claude Deveau, Wade Hazel, Stephen R. Young, Allen Lussier, Robert Copeland

"LocationSometimes known as the Bernie Lake mine, the mine is located about 180 km east-northeast of Winnipeg on the northwestern shore of Bernie Lake, close to the Nopiming Provincial Park and the Manitoba-Ontario boundary. The mine is accessed from Lac du Bonnet which is linked to the provincial road system.Brief Description of OperationTantalum Mining Corporation of Canada Ltd. operates an underground mine employing ramp access, room and pillar mining, and shaft hoisting for the production of tantalum, lithium and cesium minerals. Daily campaigned crushing of the tantalum and lithium ores supply separate concentration circuits. Tantalum recovery employs conventional gravity equipment together with recently developed centrifugal concentration methods. All tantalum concentrates go to Cabot Performance Materials for the production of tantalum chemicals and metal. Lithium minerals are recovered using heavy medium separation and silicate flotation to produce spodumene and montebrasite/amblygonite concentrates. The lithium concentrates are shipped worldwide for use in ceramics, specialty glass and mold powders. Cesium processing involves the dry grinding of pollucite as feed stock for the recently built on-site chemical plant dedicated to tl1e production of cesium formate, a high-density drilling fluid for use in the oil industry."

Jan 1, 2000

By Theophile S. Yameogo

Les ressources naturelles ont en général été le moteur du développement économique et social des nations. Les pays aujourd?hui développés sont pour la plupart d?anciens eldorado, charbonniers ou pétroliers. D?autres le sont toujours. L?Afrique fait cependant figure d?exception : même en étant comblé de ressources naturelles exceptionnelles, les pays de ce continent croulent sous le poids de la pauvreté et de ses acabits que sont les maladies, la famine, la guerre et l?insurrection sociale. On reconnaît néanmoins qu?il y a des cas particuliers comme le Botswana, la Namibie, l?Afrique du Sud. Face à cette situation, beaucoup de scénarii ont été proposés sans pour autant porté les fruits espérés. Le rapport Brundtland suggère que le développement durable est la clé du succès car elle veille à la prospérité économique, à l?équité dans la société et à la pérennité dans l?environnement. Pour l?Afrique, beaucoup de facteurs doivent être considérés et les solutions se doivent d?être pratiques et éthiques. Le futur ingénieur des mines qui a écrit ce rapport, apporte sa vision de la situation non sans avoir auparavant analysé les faits. Cette démarche, qui se veut avant tout éthique, inclut les aspects sociaux, économiques et politiques. Introduction In the 40s, 50s and the 60s, many economists, among which Harold Hotelling from South Carolina University, thought that developing countries could reach socio-economical success by extracting their natural resources such as oil and minerals. The current economical disaster seems to have contradicted that belief and critics like Davis Graham (Colorado School of Mines) and Michael Ross (University of California at Los Angeles) even suggested that extractive activities stop in Africa. But the experts of the World Bank (Mining Department) and some mining and oil companies are committed to reverse the tendency by implementing a new approach. Considering the principles of sustainable development defined in the Brundtland report (1987), we decided to analyze the possibility of giving the extractive industry a catalytic role in creating a socially, economically and environmentally development in Africa. In other words, can we continue to mine and extract oil in Africa for its blossoming future under the ruling of the sustainable development? In the following, we start by explaining the African socio-economic and political context. After a brief definition of the sustainable development, we explain why, for Africa, some believe in the extractive industry and some don?t. In the end, we draw out conciliatory arguments.

Apr 1, 2005

By A. S. Moghaddam

The transportation of cemented and non-cemented mine tailings in the form of paste through pipelines is one of the main stages of paste backfill operations. For the purpose of pipeline design, the rheological properties of the materials, such as yield stress and viscosity must be determined. In this study, the yield stress of two Canadian mine tailings, for gold and copper mineralization, were studied using the vane method and slump tests. The comparison between the vane method and the slump tests indicates that the slump tests generally overestimate the yield stress values for both cemented and non-cemented paste backfills. In addition, the effects of 5% Portland cement (type 10) and mixing time on the yield stress of paste backfills were investigated. The percentage of cement as a binder agent has a direct effect on the increase of the yield stress of paste backfills. Yield stress measurements show that mixing times of 4 minutes and 12 minutes have the same effect on the yield stress values.

May 1, 2007

By J. P. Sancho, L. F. Verdeja, J. I. Verdeja

"This paper analyzes the present state of the different processes competing to keep their market shares within the future iron and steel business sector.The continuous transformations in the steel making process are also studied here. These transformations have happened especially during the two last decades obviously favouring steel price, properties, quality and environmental compatibility in the new millennium. IntroductionIn the early 1980s, world steel production reached a historic figure; specifically in 1982, the amount was 645 Mt (Verdeja et al., 1993). This might have been one of the reasons why the United States, Japan and the European Community drew up a declaration of principles after which the leading industries and sectors in the following century’s development would be: advanced materials, also known by the very diffuse term of new materials; information technologies; and biotechnology (Eager, 1998).On the threshold of the 21st century, it can be inferred that information technologies (computers and telecommunications) have progressed spectacularly. Nevertheless, there have been downsides too; technology develops so quickly that after a few months the products are obsolete. Environmental problems may also appear in a few years due to storing so many useless devices. At the same time, the achievements of biotechnology did not meet the optimistic forecasts made in the early 1980s.On the other hand, it is also curious that some solutions for the environmental problems generated by star technologies of the new millennium, such as computers and biotechnology, are closely linked to the iron and steel industry. For example, blast furnaces in Germany and Japan are prepared for burning residua by introducing polymer materials from computers and other electronic prepared devices through their tuyeres, while cement tube furnaces can destroy any organic residua from different origins."

Jan 1, 2002

By H. J. McQueen

Large-scale industrial production of pipe began with longitudinal hot pressure welding of wrought iron by passage of skelp (narrow strip with beveled edges) through a die or bell that curled it about a longitudinal axis until the edges were forced together. Such small to medium tubes could be reduced by rolling or drawing; with threaded connections, they were excellent for distribution of clean water and of illuminating gas for street, home and industrial lighting. Although steel lacks the fluxing slag for pressure welding it has hot strength similar to iron; hot-pressure bell welding was advantageously transferred to steel in long coiled strip with 50% higher cold strength. For pipe without weld-line defects, hot cupping followed by Pilger mill rolling produced tubing that revolutionized bicycle quality and high-pressure service for boilers and chemical processing. Mannesman hot rotary piercing produced long thick walled tube that permitted reduction or expansion by rolling to provide pipe sections up to 60 cm diameter and 12 m long. During 1910 - 1940, oil and gas pipeline technologies, notably welding evolved markedly as they proliferated in the United States, in response to far-flung petroleum fields, expanding industry consumption and the automobile revolution. In the Second World War combat pipelines were laid rapidly, such as: the Canol line through the Yukon to Alaska, and fuel supply lines across the channel and through liberated France. Perfection of welding techniques for both longitudinal and spiral weld large diameter pipe in combination with controlled-rolling of micro-alloyed steels made possible reliable Arctic pipelines. The development of pipe production and utilization in Canada is recounted. The fabrication techniques and metallurgical controls are explained.

Jan 1, 2005

By Rayleen Riske

Why do we look for better reconciliation when times get tough? Why wait? Mine reconciliation should be a priority throughout the good times too. In fact, with good reconciliation, those good times are going to be even better and will help pave the way to success through those preventable bad times. Reconciliation throughout the entire mining value chain requires the capture, validation, and analysis of copious amounts of data. This task can be daunting for a team in a small mine, let alone reconciling across a suite of large mines. This paper will outline the different ways we can reconcile across the value chain, why we should reconcile over differing periods of time and how Snowden?s solution to proving reconciliation can be a simpler, reliable and transparent process. Snowden?s Reconcilor is proving to be a valuable tool on any mining scale, by capturing, validating, sorting and reporting data for timely decision making by the site geologist through to corporate management. By instigating vigorous reconciliation, you are setting your mine up for the future. Not only will you have the means to analyse your current processes and measures, but you will have the opportunity to identify and improve your mine?s performance from the resource model through to the final product.

May 1, 2010

By H. C. Gunning

SOME small vanadium-bearing deposits on the west coast of British Columbia about 100 miles north of Vancouver are of interest for several reasons. They are of a type that is, so far as we know, unique. They are difficult to identify as being vanadiferous so that, unless they are described, other similar deposits could easily pass unrecognized. Furthermore, although none of them has as yet been proven to be of commercial proportions, no good reason is apparent why larger, and therefore valuable, deposits should not occur under similar geological conditions. The original discovery on Quadra island was made in 1932 and has been recorded by H. V. Ellsworth and H. C. Gunning (l). Since 1932, prospecting in the area has revealed other similar deposits, one about a mile south of the original and another some ten miles to the east, near Menzies bay on Vancouver island. The Quadra Island showings are a mile and a half north of the head of Gowland harbour, a small inlet that is easily reached by gas boat from Campbell river, about four miles to the southeast on Vancouver island. The deposits were examined by the writers in the spring of 1943 in connection with field work sponsored by the Department of Geology, University of British Columbia. We are indebted to Mr. G. A. Dirom and Mr. Lothrop, of Vancouver, for helpful data on the Menzies Bay deposits, and to Dr. V. Dolmage for making a brief trip to Gowland harbour and discussing the deposits.

Jan 1, 1944

By C. Pelley, S. Kelebek, T. Katsabanis, B. Nanthakumar

"As part of a larger investigation on generation of fines from mining activities and their effect on downstream operations, ore samples from Onaping area stockpiles of Falconbridge Ltd were studied. Batch flotation tests were conducted on the stockpile samples and fresh ore samples to explore the effect of stockpiling on grade-recovery performance. Head grade and particle size distribution of the samples from stockpiles were adjusted so that the samples compared are similar to each other. In additional tests, fresh ore samples were blended with stockpile samples at various percentages, representing 27.4, 50.2 and 81.5% of stockpile samples.The samples from stockpiles produced inferior nickel grade-recovery curves compared to fresh ore. The poorer grade-recovery performance was attributable to two factors. First, a significant dilution effect was observed due to the nearly complete flotation of pyrrhotite. Secondly, while pyrrhotite from stockpiled ore became highly floatable, the same stockpiling conditions caused nickel losses that were attributable to non-floatability of some pentlandite.In the case of blending, there was generally insignificant difference in the nickel grade-recovery between fresh and blended samples when the blending cases involved 27.4 and 50.2% stockpile samples. However, an increase in pyrrhotite recovery was observed for both blending cases. At 81.5% blending case, degraded grade-recovery was significant primarily due to the nearly complete flotation of pyrrhotite. There was a small, but noticeable amount of nickel loss for this case. However, for lower ratios of blending this loss was negligible.The increase in pyrrhotite recovery was partly attributed to its activation by Cu and Ni ions. Formation of a significant amount of elemental sulphur was also apparent from analysis of stockpiled samples. It can be concluded that pyrrhotite is mildly oxidized under stockpiling conditions while part of the pentlandite undergoes a more severe oxidation."

Jan 1, 2006

By W. J. Weymark

"The Gregg River project is located 40 kilometres southwest of Hinton, Alberta, adjacent to and east of Jasper National Park. This metallurgical coal mine has been developed as a joint venture between Gregg River Coal Ltd. (a subsidiary company of Mana/ta Coal Ltd.) and seven Japanese companies. This 200-million dollar project consists of a conventional truckshovel open-pit operation and a coal preparation plant rated at 2.14 million tonnes of clean coal per year. Mining operations started in October 1982 with plant start-up following in April 1983. Introduction This paper is an overview and update of the Gregg River project, a metallurgical coal mine being developed as a joint venture between Gregg River Coal Ltd. (a subsidiary of Manalta Coal Ltd.) and seven Japanese companies. The Gregg River Coal leases cover 3440 hectares and are located 40 kilometres south of Hinton, Alberta, adjacent to and north of Cardinal River Coal Mine (Fig. 1). This 200-million dollar project consists of a conventional truck-shovel operation and a coal preparation plant rated at 2.14 million tonnes of clean coal per year. A total of 31.5 million tonnes of clean metallurgical coal will be sold to the Japanese over a fifteen-year term. At present, mining operations are ahead of schedule and the plant started up on schedule in April 1983. Access and Climate An all-weather road, Highway 40, connects the minesite with Hinton (the nearest commercial centre) and a Canadian National Railway (C.N.R.) spur line connects the minesite with the C.N.R. main line in Edson. Hinton is accessible by road chartered airline and rail. ' ~h~ rug~ed and varied topography in the area creates large vanations m temperature and precipitation over short distances. The region is characterized by precipitation throughout the year long cold winters and short cool summers. The mean temperatur~ of the area range from a low of -14°C in January, the coldest month, to a high of 12°C in July, the warmest month. Long-term precipitation data indicates a mean yearly precipitation of 870 mm of which 620Jo occurs during the summer months."

Jan 1, 1985

By A. Flemming

"As the next century draws near, new mine properties must be brought into production to replace existing operations that are approaching their economic life. This paper presents some of the critical technical issues being addressed by Manalta Coal Ltd. as they strive to bring the Telkwa Coal Project near Smithers, BC into production during the year 2000. The mine is planned to produce between 1.0 to 1.5 million tonnes per year of medium volatile coal for export to overseas thermal and PCI markets. IntroductionManalta Coal Ltd. (Manalta) is proposing the development and operation of a surface coal mine and associated infrastructure approximately six kilometres southwest of the village of Telkwa, British Columbia (Fig. 1). The infrastructure consists of a coal washing facility, tailings disposal area, clean coal haul road, access road and rail loadout facility. Over a 25-year period, the mine is expected to produce between 25 and 37 million clean tonnes of coal primarily for the export market.To achieve public and governmental approval for the development, the project will be reviewed under British Columbia’s Environmental Assessment Act. Manalta entered the formal Assessment process in February 1, 1997 with the submission of an Application for a Project Approval Certificate for the Telkwa Coal Project."

Jan 1, 1997

By J. R. Gill

Introduction The property and plant of the Falconbridge Nickel Mines, Limited, is situated about 13 miles northeast from Sudbury, in Falconbridge township, near the eastern extremity of the southern Nickel Range. As early as 1899 or 1900 some work was clone on this property by the late Thos. A. Edison, when a shaft was sunk through 80 feet of overburden to within a few feet of the ore-body. At this point quicksand was encountered, which made it impossible to continue with the equipment at hand. As a result, the activities of the Edison party ceased in this section. There was no further progress until 1915 and 1916, when an extensive diamond-drilling campaign, carried out by the E. J. Longyear Company, located the ore-body that is now being worked. The property was acquired by the present operators in 1928, and in September of that year active mining development was commenced. Features Influencing Design Of Plant Early in 1929 plans were prepared for a smelter and the necessary crushing and sorting plant. In spite of the general trend towards the reverberatory furnace as a smelting unit, it was decided to erect a blast-furnace plant. The limited tonnage to be treated, of course, influenced this decision to a great extent. However, it was known that, with the proper procedure, extremely favourable results, both economic and metallurgical, could be obtained in blast furnace smelting. The possibility of very low slag losses, the simplicity of operation by the elimination of roasting plant, fuel plant, etc., the ability to handle coarse feed, and the lower initial cost, were considered factors in favour of the blast furnace. Notwithstanding the fact that we might be called on to treat a certain amount of concentrate, it appeared that the blast furnace was the proper unit for the contemplated operation.

Jan 1, 1932

By J. A. Relf

The construction of refineries and gas conservation plants in the general Edmonton area in the early 1950's made available large quantities of by-product liquified petroleum gases (LPG). These gases, together with discovery of increasing reserves of natural gas in the Edmonton area, provided Canadian Chemical Company with two of the necessities for petrochemical production, namely, available and reasonably priced raw materials and fuel. This paper outlines the development of the $83 million Edmonton plant from its origin, together with a brief description of the processes and some of the interesting features involved. Several economic aspects of the petrochemical industry are high-lighted including its importance to the local community and the province. The paper reviews the relationship between the oil and gas industry and petrochemical manufacturing and indicates some of the factors that may affect the future growth of the petro-chemical industry in Wes tern Canada.

Jan 1, 1962

By H. R. Banks

"AbstractThe rod mill introduced into the Sullivan Concentrator flow in September, 1948, replaced two sets of 74 in. by 20 in. rolls and their accompanying screens. In addition to the work formerly done by the rolls, the rod mill is producing a finer product and one which provides more suitable feed for the primary ball mills. The object of the finer discharge from the •primary mills is to make possible a feed directly from the mills to a series of flotation machines where a large portion of the galena can be withdrawn from the circuit while the galena is still coarsely granular. The interposing of classifiers between grinding and flotation means the selective grinding of the galena.The author summarizes the work of •the rod mill through the first 5,000,000 tons and shows that the wear of lifters, liners, and rods is definitely below normal for the type and size of rock being handled. The rod mill, driven through a fluid coupling, has been subject to a range of speeds from 13.5 to 19. A pinion in the speed reducer was changed to allow the extending of the normal speed range of the fluid drive of approximately 4 r.p.m.Since the critical speed inside the liners •is 23.4, the range •in per cent of criticial is 57.7 to 81.2 per cent.The capacity of the mill increases with increasing speed but the character of the product remains approximately the same except when the feed rate is too high.Consumption of steel, power, and other operating data are presented.The author introduces certain fundamental observations on the principles involved •in comminution in order to support the special design and operation of the rod mill."

Jan 1, 1952

By J. Lee, M. Peart, T. Bhambhani, D. R. Nagaraj, P. Riccio

"Over the past decade or so, our efforts have focused on developing the rationale and concepts for new technology in reagent development and optimization in the processing of base and precious metals. A major outcome of these efforts have been the development of a novel family of collectors, principally driven by the MAXGOLD® and Aero XD-5002® chemistries, for precious metals recovery from primary Au ores and Cu-Au ores. These chemistries was developed to be robust to address the complex mineralogy and gold deportment in these ores. Plant trial data for a variety of ores have confirmed that the both Aero® XD-5002 and MAXGOLD® chemistry are indeed versatile in recovering gold values occurring as gold alloys and/or associated with many types of sulfides, and in altering the deportment of certain sulfides (such as those bearing As, Bi etc). An overview will be given in this paper using plant data to highlight the application of these reagents.INTRODUCTIONThe subject matter of this paper is the flotation of Au containing minerals from their ores. The motivation from this manuscript comes from the several challenges faced with the processing of Au ores, as was articulated in detail by Nagaraj (2008). The biggest challenge is the complex mineralogy; most easy-to-treat free-milling ores bodies are largely depleted. The Au values are distributed in multiple host minerals such as pyrite, pyrrhotite, arsenopyrite and Cu minerals such as chalcopyrite. Au values also happen to be finely disseminated within the various minerals and are sometimes invisible in optical microscopy. Additionally, on any given day, some mines treat multiple ore types, and the mineralogy is different for each ore type.Xanthates continue to be the collectors of choice at most Au and PGM operations around the world. Most primary Au operations tend to consume very large amounts of collectors; the dosage ranges anywhere between 40-400 g/t and this has been attributed to both mineralogical and non-mineralogical factors (non-mineralogical factors include the low cost of xanthates and the mindset that “more is always better”, which is not necessarily the case). In addition, several studies now show that xanthates alone are never sufficient where multiple value minerals are present, and that supplementary collectors are required. The large doses present a substantial cost to the minerals industry, and many mining companies have expressed the need for more efficient reagents that can improve metallurgical performance at low dosages."

Jan 1, 2013

By P. P. Sinha, D. N. Bhatia, B. R. Ghosh, R. K. Gupta

Medium carbon, low alloy, high-strength steels containing Ni, Cr, and Mo are used for the fabrication of various types of high-strength fasteners required for launch vehicle structures. Cold heading properties and response to hardening and tempering are the essential requirements of the material for fabrication and application, respectively. Combining these two requirements is essentially warranted in high-strength fastener-grade steels. Cold heading properties require ductility, which can be achieved through spheroidizing treatments. In the absence of a suitable spheroidizing cycle for medium carbon 3.8 Ni, 1.8 Cr, 0.3 Mo steel, experiments were carried out with a theoretical understanding of the alloy system. This paper presents the experiments and results obtained after a spheroidizing treatment, which was carried out to optimize the process. Hardness measurements were carried out and microstructural studies were conducted to assess the spheroidization process and to determine the optimal spheroidization parameters.

Jan 1, 2007

By C. Velásquez, W. Bergholz, C. Spence, P. Lind

NuevaUnión SpA (NuevaUnión) is a development project located in the Huasco province of the Atacama region of Chile. It is held in a joint venture company owned 50:50 by Teck Resources Limited (Teck) and Newmont Goldcorp. It includes the Cu-Mo Relincho deposit and the Cu-Au La Fortuna deposit, with plans to utilise a single concentrator to be built at the Relincho site. The Relincho site is at an altitude of 2,000 masl and is 40 km from the La Fortuna site which is at an altitude of 4,100 masl. The project is currently completing a Feasibility Study and is reviewing equipment selection and flowsheet options. This paper is based on the current thinking, and design decisions will be finalized at the completion of the Feasibility Study. NuevaUnión is currently planning for phased operation, processing Relincho ore at 104 ktpd followed by processing ore from La Fortuna at 116 ktpd. Plans for the third phase include doubling the main processing lines and returning to Relincho ore at a processing rate of 208 ktpd. The NuevaUnión concentrator will incorporate comminution and flotation circuits that are being designed to maximize the overall economic value of the combined ore deposits. Major ore characteristics differ between the two ore bodies, such as ore competency, grindability, liberation grind size, pulp rheology, tailings properties, minerals and metals of value, as well as gangue mineralogy. Mineral processing choices have been made to optimise value from each deposit and the combined project. INTRODUCTION Between 2010 and 2013, two significant mining projects were being developed in Chile: Goldcorp’s El Morro project had recently finalized a Feasibility Study and, in 2011, had received its environmental approval for construction; and Teck Resources Limited’s (Teck) Relincho project was finalizing a Feasibility Study and preparing its Environmental Impact Study. Both projects were: Geographically close, at only 40 km apart. Considering similar infrastructure. Each was planning to have its own concentrator, tailings management facility, high voltage power line, port, concentrate transport system, seawater desalination plant and pumping system to mine site.

Jan 1, 2019

By H. C. Horwood

INTRODUCTION THE Argosy Gold Mines, Limited, which joined the ranks of active Ontario gold producers during the summer of 1936, holds a group of 21 claims on Casummit lake, in the Patricia portion, district of Kenora, northwestern Ontario. The Company is developing and mining goldbearing quartz veins that occur in a series of greywackes and slates of probable Keewatin age. The writer made a geological examination of the property and the surrounding area for the Ontario Department of Mines during the early part of the field season of 1936. This paper is a report on the general geology, structure, and ore deposits at the mine and is based almost entirely on data compiled during the examination. HISTORY Mineralization was first discovered on the property in May, 1929, by A. F. Hewitt, who, with J. A. Borthwick, decided that the country had prospecting possibilities and commenced work in April. Mr. Hewitt staked, and with his partner, J. Ziyone, still holds the group of claims lying immediately east of the present Argosy holdings. Mr. Borthwick staked six claims, K.R.L. 9,681 to 9,686, inclusive, adjoining Hewitt's on the west and later added claims K.R.L. 9,733 to 9,740, inclusive, to his holdings. F. Fiskness, who was also prospecting in the region, discoveted No. 1 vein on Borthwick's claims, and with his two partners, L. Parth and H. Jones, staked claims K.R.L. 9,758 to 9,763, inclusive, to the northwest of Borthwick's and Hewitt's ground. In July, 1929, the Casey Mountain Operating Syndicate, which held ground to the northwest, secured an option on Borthwick's claims. The Fiskness-Parth-Jones property was added in January, 1930, to protect the west dip of the veins. During the winter of 1930-31, the veins were explored by diamond drilling, No. 2 for a length ?of 900 feet and a vertical depth of from 51 to. 375 feet? and No. 3 .t~ a slope depth of 175 feet. I~ August, 1.931, after the msrallat10n of a miming plant, the Casey Summit Gold Mmes, limited, was incorporated to take over the property from the Syndicate. The Maple leaf Mines optioned a controlling interest in the stock in August, 1933, and on September 17th, 1934, brought a 50-ton amalgamation mill into production. From early in October to December 27th, 1934, when the mill was closed down, 4,094 tons of ore were treated to yield 887.89 ounces of gold and 87 .26 ounces of silver( ! ).

Jan 1, 1937