Search Documents

The use of rubber-tyred equipment in a decline mining system requires that roadways be kept free of running water. At Renison this is achieved by the use of stage pumping or gravitating to a major pump station and pumping from there directly to the surface. The frequent use of pick-up lines and pump boxes in the decline system provides a method of water control and reduces the amount of slimes in pump lines. The Bassett Fault structure, which lies on the hangingwall of the mine is the major source of ground water. This is encountered in diamond drill holes and exploration develop- ment. Dewatering of this structure is possible by controlling the flow from selected holes. Future pumping requirements may be predicted by analysing changes in the level of the water table and by calculating dewatering rates required to maintain ore reserves available for production.

Jan 1, 1977

Faced with low prices and weak demand in an oversupplied market, the Australian coal industry must seek to further reduce its costs. The paper examines minesite competitiveness of the open cut coal industry in Australia with some references to the coal operations of M.I.M. Holdings Limited. The make-up of F.O.R. mine costs is analysed in order to identify where efforts should be directed to maintain competitiveness. The scope for mine site improvements through changes to working practices, the application of new technology and cost management is examined.

Jan 1, 1987

By L Grigorov, G J. Jame, A V. Nguyen

The dewetting kinetics between a small air-liquid interface and a silica (negatively charged in water) planar surface in solutions of dodecylammonium chloride (cationic surfactant) has been investigated using the Scheludko cell and digital high-speed video microscopy. The gas-liquid interface was created at the bottom of a small silica capillary of the cell and then was moved towards the silica planar surface. After the rupture of the liquid films between the interfaces, the expansion of the gas-liquid-solid three-phase contact (TPC) line was observed and recorded using a digital high-speed video microscope system, operating at 1000 frames per second. The surface tension of the surfactant solution was measured using the pendant drop technique. The equilibrium contact angle was measured using the Scheludko-Minings method with a silica micro-sphere. The TPC radius was determined as a function of time and compared against the available hydrodynamic and molecular-kinetic models. The experimental data are described very well by the molecular-kinetic model for the TPC line motion. The hydrodynamic model is in agreement with the experimental data only for a short time after inception of the three-phase contact expansion.

Jan 1, 2005

By S F. Simmons, A McOnie, J L. Mauk

Three cross sections, 200 m apart, display the distribution of indicator hydrothermal minerals across the Empire zone of the Golden Cross epithermal Au-Ag deposit, Waihi, New Zealand. These minerals are used to interpret the temperature and composition of hydrothermal fluids. The distribution of interstratified illite-montmorillonite and illite indicate that temperatures ranged from 140 to >220¦C, with temperatures above 220¦C predominating. The mineral assemblage of quartz-adularia-chlorite-illite-calcite-pyrite envelops the Empire vein system and stockwork, and reflects formation from an alkali chloride water whereas the mineral assemblage of replacement calcite-interstratified illite û montmorillonite-kaolinite forms a carapace and reflects formation from a CO2-rich steam-heated water. Alkali chloride waters appear responsible for the epithermal Au-Ag mineralisation.

Jan 1, 1995

The Burragorang Valley lies approx. 95 km by road south west of Sydney and some 35 km west of Camden. It is over 80 km in length and varies in width from 3 km to over 16 km. Geologically, the history of the Burragorang Valley is of interest. It was referred to by early geographers and N.R.M.A. booklets as the largest sunken valley in Australia. This description is incorrect as it is a water worn valley formed by the dissection of an uplift in the south western portion of the large Sydney Sedimentary Basin. Ages2 ago there extended right across the Blue Mountains, a continuous tableland into which the Nattai, Wollondilly and Cox's Rivers have carved out the formation of the Burragorang. This dissection together with other valleys such as the Megalong, Jamieson and Grose, formed part of the eastward drainage pattern of the uplifting tableland into the Pacific ocean. The lapse of time since the streams in the Burragorang began their work of erosion can

Jan 1, 1976

A review is presented of techniques cur- rently in use, or being developed, to enable the determination of virgin rock stress at consid- erable depth (> 1000 m) from small diameter sur- face drill holes (

Jan 1, 1975

By Millen M. J, Rainey S, Sowerby B. D

The control of size reduction in grinding machines and circuits may be enhanced by a continuous and accurate measurement of the particle size of solids in appropriate process streams. This paper presents a brief review of commercial particle s

Jan 1, 1997

By Mullens P

Recent advances in technology have allowed many of the problems of directional control of long diamond drill holes to be overcome. Three case histories are presented, from Cobar, Hilton North and Mount Isa Mine, in which careful hole design and the use of wedges and down-the-hole motors have allowed tight directional control of drilling. Substantial savings in time and cost were achieved in all three cases.

Jan 1, 1990

By Clarke B. N

The Olympic mine is currently and development to 1988. The mine practice is, and number of factors. Dam copper-uranium-gold undergoing construction start production in May ventilation design and will be determined by a These include: 1. Mining method and degree of mechanization. 2. Presence of radon emanating material. 3. High virgin rock temperatures at relatively shallow depths. 4. High ambient air temperatures in Summer.

Jan 1, 1988

By Ren T. X, Jozefowicz R

In many branches of engineering, there has to be an understanding of the motion of fluids in order to solve problems. Many safety and health problems in the mining industry are typical examples that involve the understanding and analysis of fluid flow, such as explosions, the spread of fires, dispersion of gas and dust, and ventilation patterns. Computational Fluid Dynamics (CFD) is concerned with the use of computers to produce information about the ways in which fluids flow in given situations. Until recently CFD has been widely applied to a variety of industrial sectors and increasingly to problems in the health and safety areas. With the arrival of more powerful computers and CFD packages, CFD techniques are no longer practised solely in a research environment, but can be used by engineers in many industrial fields. This paper introduces the basic concepts and general procedures involved in the use of CFD technology. A comparison is given as a guide to the major features of a number of widely used commercial CFD codes. Areas of potential CFD applications are identified in a range of safety and health problems in mining industry. An example is presented to illustrate the use of this technology. It is believed that the exploitation of these areas using CFD approach will contribute significantly to the solution of today's many mine health and safety problems.

Jan 1, 1995

By Lindner E, Bosio M

South Australian coals are all low in rank and generally poor in quality, with difficult combustion characteristics. This circumstance makes the selection of a fuel source for future power generation difficult, requiring careful study and detailed analysis of the various alternatives. Combustion characteristics can have a significant effect on plant design and costs, and need early attention in any exploration and evaluation programme. The physical location of the deposits, often remote from established infrastructure and centres of population, is also a major factor in the ultimate cost of power at the poirl use.

Jan 1, 1977

By OÆGrady P

Finite element analysis is becoming a routine component of design of longwall extractions, now superseding more traditional somewhat intuitive approaches. Finite element modelling is relatively inexpensive and provides an adequate degree of similitude to give satisfactory analysis. The physical modelling of two decades ago is now largely replaced by numerical methods of which finite element is the best known. Important data for finite element work are physical properties, including creep aspects, introducing the non-linearity of stress response.Various computer packages are available and some were used to model two specific UK examples, using both linear and non-linear approaches. It appears that non-linear approaches will yield most benefit. The use of materially non-linear analysis is merited by the greater similitude it provides between model output and real mine situations.

Jan 1, 1991

Copper heap leaching involves both the simultaneous and sequential leaching of very large tonnages of ore over long periods of time. It is not unusual to be leaching three or four million tonnes over periods of 12 to 18 months. As a consequenc

Jan 1, 1998

This paper addresses the area of utilising automatic data capture systems in the metalliferous mining environment for the purpose of tracking personnel and vehicles, for both safety and productivity purposes.As automatic data capture systems in the form of barcodes have revolutionised the stock control procedures in retail establishments in recent years, so too will similar systems in the form of radio frequency identification products (an electronic version of the barcode) transform the way in which many aspects of mining operations will be managed.

Jan 1, 1992

By Kaleta S, McTavish LP, Turner RD

Primary production blasting at Hamers- ley Iron began with seven inch holes at Tom Price in 1966 and has developed since then to large multiple row shots of 381 mm holes at Tom Price and 311 mm at Paraburdoo. Up to 1.3 million tonnes are initiated in a single blast with the average around 300,000 tonnes. Development can be traced through Anfo, AlAnfo, slurries, various boosters, initiation and delay techniques, hole loading and daily operating practices. A standard practice could be developed for the two mines for normal pro- duction blasts; this would not apply to such common variations as low "paddy" shots, pre- splitting, tight corners necessitating single row drilling etc. Because of ground variation three or even four sizes of drill holes may well be economic- al for blasting, even though this would be off set by complications in operation, supervision, store stocking and maintenance, particularly in Drilling.

Jan 1, 1978

Grade control is an important factor in the on-going success of a mining operation. Grade control criteria will vary depending on the commodity being mined. Financial considerations determine the actual grade control criteria at any one mine site. Mining and metallurgical capital and operating costs are ultimately used in ascertaining cut-off grades employed in grade control. The metallurgical characteristics of the ore, and ultimately the equipment selection and design of the plant, are based on samples provided by the exploration geologist. Ore variability is an important factor in designing the process plant. Ore variations, outside of those catered for in the design, as well as large ore changes on a daily basis, will impact on the metallurgical performance, and hence the economics of a mining operation. Therefore good liaison between the grade control geologist and metallurgist will undoubtedly lead to a more consistent, and more profitable mining operation.

Jan 1, 1993

By Ulvelin K, Antila K

Large scale cut and fill mining in narrow silver-lead-zinc orebodies began at Mount Isa in 1964. Initially each orebody was one stope and access was via raises from the level above. Upholing was the principal mining method, although flatbacking was employed where ground conditions were more difficult. Developments since have included access via footwall inclines and connection of all stopes with major crosscuts. Flatbacking is the principal method. The most recent cut and fill operation is now fully mechanised using drilling jumbos, rockbolting jumbos and load-haul-dump units. Improved ground support and drilling and blasting practices have enhanced safety, recovery and productivity in all cut and fill operations.

Jan 1, 1988

By Leigh J. H

A history is given of the dust control techniques developed and applied by the mining companies at Broken Hill. A history of the regeneration works undertaken since 1936 is out- lined. Particular emphasis is placed on the stabilization of mine residue dumps which are located throughout a belt of mining leases in the middle of the city and which began in 1937. The establishment of vegetation for dust control techniques is discussed in detail and a case study is given of the successful revegetation of the sides of a 650 metre long, 350 metre wide and 35 metre high residue dump.

Jan 1, 1976

By Floyd J. M

The recovery of gold from refractory ores and concentrates can be achieved in a number of ways using roasting and leaching procedures. The Sirosmelt system introduces a new approach to the recovery of gold from these materials using smelting procedures. Laboratory studies were carried out to establish procedures for operating the Sirosmelt system for recovery of gold and associated valuable elements from an ore containing 17.5 g/t gold and a concentrate containing 22 g/t gold as well as substantial copper levels. Copper, iron, lead and matte were evaluated as collecting phases for the gold. The ore smelting procedure recovered 80-90% of the gold whilst smelting concentrate gave 98-99% gold recovery.

Jan 1, 1987

The care necessary to ensure a reliable estimate of average value from the individual values of a series of bore holes sunk in any alluvial deposit containing coarse gold was well exemplified in checking over the mining returns from a previously bored deposit in Central Otago, N.Z. While the working returns are always liable to vary considerably from bore values in any particular sub-section of an area, still, over any considerable area, the two must check within small limits, if profits are to be calculated and capital raised on the average value given by boring.The present figures have probably more value than those from, dredge returns since accurate measurements are difficult to obtain in irregular water-filled dredge paddocks, whereas in the case under review the paddock walls stood almost perpendicular, and, as the measurements were taken and checked in the empty rectangular excavation, the yardage estimate may be taken as substantially exact.NATURE OF DEPOSITThe area consists of a narrow valley deposit of fluvio-glacial origin, the original deposit having been eroded and the gold reconcentrated by post glacial rivers. The wash is between 80 and 90 ft. deep, and is formed in two distinct layers:(i.) The top layer from surface to 70 ft. or 80 ft. consists of about equal quantities of gravel mixed with glacial drift, and a small amount of clay. The gravel is typical discoid glacial stone of a maximum size of about 4 in. diam. by 1 in. thick, and consists of soft micaceous schist and laminated slate. This upper layer of wash contains no coarse gold whatever, and very little fine; indeed, in mining, the top 30 ft. is discarded without being passed over the boxes.(ii.) The lower layer of wash to bedrock is similar to the upper, except iihat it contains about 10% of larger discoid stone up to 12 in. diam. by It in. thick; 90% of the gold is concentrated in this bottom layer.

Jan 1, 1929