Search Documents

By Peng S. S

Measurement of pressure distribution under the base plate of the Hemscheidt 2-leg 800-ton shield was performed underground for two shifts using 12 pressure cells installed in two rows, one each under each split base plate. Pressure distribution was uneven depending on contact condition. In general the highest base pressure occurred at 1/3 of the base plate contact length from the rear edge. The resultant was near vertical, and the pressure under the tail side split base plate was always higher than the head side. For comparison, pressure distribution on the canopy and under the base plate was also measured under controlled conditions at the USBM's Mine Simulator Testing Facilities in Pittsburgh, PA. A total of 45 tests were conducted under several simulated contact conditions. The results showed that the actual contact area is highly dependent on the compliance of the immediate roof and floor due to the sloped canopy tip and a base lifting device under the base tip. The loading distribution tends to change in magnitude and profile as the leg pressure increases. The base lifting device exaggerates the high toe loading on the base plate characteristics of this type of shield support.

Jan 1, 1992

By De Jong HJ

During the forthcoming reline of No.3 Blast Furnace at the Newcastle Steelworks of the Broken Hill Proprietary Co. Ltd., facilities for the screening and weighing o' coke will be installed. The equipment is needed to optimise the sizing and the quantity of coke immediately prior to it being charged to the furnace. Up till the time the furnace was blown out in November, 1982, coke was charged to the furnace by volume, ie by skip fulls only. This resulted in variation to the ore/coke ratio charged due to bulk density changes and erratic skip filling levels. This in turn affects the heat balance of the furnace and causes fluctuations in hot metal chemistry and temperature. A coke rate penalty has to be paid also. Coke layer thickness in the furnace burden cannot be controlled closely, resulting in loss of control over gas distribution in the furnace. A grizzly type screen was incorporated in the skip loading chute but this ineffective method left a great amount of fines with the coke being charged to the furnace. Furnace permeability was therefore reduced, particularly in the hearth.

Jan 1, 1984

By Brady B. H

Increasingly, consideration is being given to the nominal `outcomes' of degree courses in engineering, including mining engineering. These are concerned not only with knowledge and technical understanding but also with capabilities in the professional application of engineering principles to problem solving, multi-disciplinary teamwork, communication and life-long learning. This paper discusses concepts of education, professional formation and training and the associated development of competencies in applying knowledge, understanding and technical insights and skills to new situations. In developing guidelines on preferred attributes and competencies in graduate mining engineers, a survey was conducted of a range of industry personnel involved in selecting graduate mining engineers. The results not only clarified the spectrum of competencies sought but also provided valuable detailed views to assist in defining a mining engineering curriculum. Considering a greater concern with the development of more `well-rounded' graduates, the implications are discussed with regard to teaching and assessment activities and the time demands on academic staff when a `coaching' role is emphasised. In line with international and Australian moves in engineering education, notions on education of mining engineering graduates in Australia are under review. The results will provide continuing challenges to all involved.

Jan 1, 1997

By Bahsford A

The presence of coal in the Sydney area was confirmed in 1891 when Cremorne Bore No. I intersected cindered coal at 1 854 m. The decision to develop Sydney Harbour Colliery was based on the results of Cremorne Bore No. 2 (drilled in 1892) in which a 3.12 m. seam of unaltered coal was encountered at 889 m. Geologists from the New South Wales Department of Mineral Resources consider that this seam is probably equivalent to an upper split of the Bulli seam. Long Cove at Balmain was selected by Sydney Harbour Collieries Ltd. as the site for mine development in 1896. This was due to opposition to the proposed establishment of a colliery on the north shore of Port Jackson near Cremorne. Construction of the main access and ventilation shafts (termed Birth- day and Jubilee), other mine infrastructure and the quay wall occurred between 1897 and 1902. A fatal accident in which five men were killed occurred during the construction of the Birthday Shaft in 1900. This acci- dent resulted in amendments to the Mining Act providing for guide rails in shafts.

Jan 1, 1988

By Wright J. K

A description is presented of the results of reduction experiments using a laboratory reduction apparatus in which simulation of the gas and temperature profiles which occur in direct reduction shaft furnaces is achieved using microcomputer control. The apparatus allows continously changing reduction conditions to be impressed on lump or pellet samples to simulate the environment that is experienced by iron ore burdens during their transit down the shaft of a direct reduction furnace. Three pellet samples and three lump ore samples were reduced in the apparatus. Comparative reduction curves and strengths after reduction for the materials were obtained over a range of reduction temp- eratures using Midrex-type gas compositions. The resulting reduction and strength curves show considerable variation in behaviour and reflect the physical and chemical variations in the individual ore and pellet types. A comparison is made of the reduction rates and modes of reduction of the samples reduced under "conventional" test conditions using a single unchanging gas composition and the simulated shaft furnace reduction conditions. It was observed that the course of reduction is very different in the two procedures and the major influence of temperature on the strength of the reduced product is noted.

Jan 1, 1987

By Szymanski J

The problems associated with underground mining continue to grow in size and complexity. As a result mine management is becoming aware of the benefits that can be achieved through the use of computer-oriented tools for system analysis. When such tools are employed in conjunction with benchmarking practices, the drivers of the system that lead to superior performance can more easily be determined. This paper discusses the use of the Simulation Language for Alternative Modelling (SLAM II) in the determination of the drivers of an underground room-and-pillar mining system. The mining operations included in the model consist of extracting, loading and hauling of the coal using continuous mining equipment in a room and pillar system. Equipment specifications and mining techniques used in the model are based upon current methods employed at the existing underground coal mines worldwide. The model developed is capable of adequately predicting the operational performance of the real world system from a statistical point of view. The results from the study show that computer simulation is an excellent tool for evaluating various mine configurations and for gaining a better understanding of the mining systems.

Jan 1, 1995

By Kane, M O&apos

The mineralised members of the Brockman Iron Formation mined at Mt Whaleback are overlain and underlain by shale horizons. To maximise resource recovery, waste movement within the life of mine plan will total approximately 3.3 billion tonnes. Approximately 15 per cent of waste materials contain zones with varying amounts of sulfides and carbon and are referred to as æreactive shaleÆ. Reactive shale has the potential to self-heat and can react with some explosives, resulting in spontaneous explosion. Sulfide rich zones also have the potential to generate acid rock drainage (ARD). Successful mining of reactive shale requires constant co-ordination between the geology, mine planning, mining and environment departments. Safe storage of reactive shale is the focus of ongoing research. Since the mid-1990s, a number of trials have been undertaken at Mt Whaleback in order to further the understanding of the physical and chemical properties of reactive shale. This paper summarises some of these trials, and discusses key learnings arising from interpretation of results. Ultimately, the learnings from this research will provide the guidelines for successful storage of reactive shale.

Jan 1, 2003

By Spark R. F

The copper deposits at Pernatty Lagoon are predominately djurleite-digenite bodies beneath the permanent water table, and chrysocolla-atacamite-malachite above the permanent water table. The minerals havebeen deposited as sheets, lobes, and pods in zones suggestive of permeability channels or permeability basius with respect to groundwater circulation.Pyrite is deposited in the form of framboids, which reflects its biogenic origin. Copper-iron sulphides deposit by replacement of pre-existent pyrite, and rarely by direct deposition. The latter mode of formation results in complex crustification bandings of chalcopyrite, bornite, sulphur rich bornites, digenite, and blue remaining covellites. The copper-iron sulphides appear to reequilibrate under constrained oxidation, resulting in an iron depletion and associated copper enrichment, the final product of which is a djurleite-digenite assemblage and associated with goethite. Where copper mineralization/ host rock relationships have rendered the rocks entirely impermeable to post ore groundwater movement, then the copper-iron sulphides are preserved as the ore assemblages.Minor and trace minerals observed include sphalerite, carrollite, galena, wittichenite, and possibly tetrahedrite in the primary ores. In the oxidized ores cllprite, tenorite, and trace brochantite have been found.

Jan 1, 1976

The three papers reviewed here consider different problems of mine management. Comparison of two of the papers demonstrates a marked contrast between the old and the new, in terms of mine management and impacts. The third paper discusses post-mining rehabilitation. The paper "The impact of a derelict base metal mine on the aquatic environment", by Brooks and Mclveen contrasts strongly with the paper "Narbarlek Uranium Mine design, construction, operation monitoring and decommissioning of the water management system" by McLoughlin, Grounds and Weatherhead. Brooks and Mclveen detail the contamination emanating today from the Conrad Mine in New South Wales which was mainly operated for 15 years at the turn of the century and later for 7 years in the 1950's. The mine was apparently developed over the years on an intermittent, ad hoc basis with no regard to contamination management, resulting Ti significant contamination persisting through time. This type of mining development is the antithesis to the type of planned mining and management operation which was carried out in Arnhem Land at Narbalek, and which apparently resulted in no uncontrolled contaminant release and successful decommissioning of the mine.

Jan 1, 1988

By Johnson G. D

Confidence in Yakabindie becoming a truly cost competitive nickel project has risen recently because of: ò the emergence of an economically effective contract mining climate; ò the delivery of cheaper energy via the Goldfields Gas Pipeline; and ò the development of the Yakabindie Process for production of nickel cathode and cobalt by-product directly from sulphide concentrates at site, dramatically cutting capital and operating costs compared to the conventional route. Development of the Yakabindie Process was a result of 'necessity being the mother of invention'. Yakabindie can now break out of the trap of relying on existing downstream processors to treat an intermediate, and instead the project can gain direct market access. The very attractive cost advantages demonstrate that hydrometallurgical processing of sulphide concentrates is a worthy prize. Improved cobalt recoveries, and tolerance of higher levels of magnesium and arsenic than allowable by smelters, are further advantages of this approach. Leach residues are combined with much larger quantities of naturally alkaline flotation tailings and remain at site. As a result the process is more environmentally sensitive than the conventional smelt/refine route, with no sulphur dioxide gas emissions and 'metal only out the gate'.

Jan 1, 1996

By G L. Simmons, K M. LeVier, R Kappes

The low potential hydrophobic state of pyrite in amyl xanthate (PAX) flotation with nitrogen is of particular interest with regard to the N2TEC flotation technology currently being used for the recovery of auriferous pyrite at NewmontÆs Lone Tree Plant in Nevada. Initially, the N2TEC system had been found to operate satisfactorily, but cyanide in the flotation mill water appeared to be responsible for a loss in pyrite recovery. This supposition was confirmed with laboratory experiments, and a program was initiated to study flotation chemistry variables by electrochemically controlled contact angle measurements. Experimental results show that activation of pyrite in such cyanide solutions can be achieved more effectively with lead than with copper. Subsequently, based on these fundamental studies, significant improvement at the Lone Tree Plant was achieved by lead activation, in which case the recovery increased to expected levels. The effect of activator is particularly significant not only with respect to pyrite depression by residual cyanide, but also with respect to collector (PAX) consumption and the initial state of the pyrite surface. Experimental results show the importance of the pyrite surface state and the rather interesting features of the activation process.

Jan 1, 2005

By G L. Simmons, K M. LeVier, R Kappes

The low potential hydrophobic state of pyrite in amyl xanthate (PAX) flotation with nitrogen is of particular interest with regard to the N2TEC flotation technology currently being used for the recovery of auriferous pyrite at NewmontÆs Lone Tree Plant in Nevada. Initially, the N2TEC system had been found to operate satisfactorily, but cyanide in the flotation mill water appeared to be responsible for a loss in pyrite recovery. This supposition was confirmed with laboratory experiments, and a program was initiated to study flotation chemistry variables by electrochemically controlled contact angle measurements. Experimental results show that activation of pyrite in such cyanide solutions can be achieved more effectively with lead than with copper. Subsequently, based on these fundamental studies, significant improvement at the Lone Tree Plant was achieved by lead activation, in which case the recovery increased to expected levels. The effect of activator is particularly significant not only with respect to pyrite depression by residual cyanide, but also with respect to collector (PAX) consumption and the initial state of the pyrite surface. Experimental results show the importance of the pyrite surface state and the rather interesting features of the activation process.

Jan 1, 2005

By R Ashworth, S J. Hall

During trials which began in May 2005, traditional steel dump bodies for transporting iron ore on 220-tonne haul trucks at a Labrador iron ore mine were compared to a novel rubber suspended dump body. Loads were measured and compared over some 93 700 loads, representing more than 20 Mt transported. Maintenance costs and downtime were also measured over the course of the trial, which lasted nearly one year. This paper outlines the parameters and results of the trials. Parameters measured included payload and production improvements, carry-back reduction, downtime due to body maintenance, and wear on the floor of the suspended dump body. These parameters were then compared to those for conventional steel dump bodies in use at the mine, and conclusions were drawn. The resulting comparisons were significantly positive in favour of the new suspended dump bodies, confirming that each truck could haul an additional 41 000 tonnes per year, that downtime hours could be considerably reduced, and that body availability and service life can be extended through use of the suspended dump body. There was also a high level of operator acceptance of the suspended dump bodies due to less loading shock and a smoother ride.

Jan 1, 2007

By Buizen M, Eagleton A. C

The results of calibration trials conducted on parachute stoppings both overseas and in Australia under a recently completed NERD&DC grant, are presented. Applications of parachute stoppings, for rapid regulation and control of ventilation networks are described including use in blasting areas and rescue work. Several parachute-type stoppings are described and their applications Investigated

Jan 1, 1988

Thank you for that introduction and especially thank you to the organisers for inviting me. I've had a considerable interest in this area and I've had the advantage of an education from Neil on the subject of offering documents as a result of our collaboration together on the Securities Information Review Committee.

Jan 1, 1989

The prevention of silicosis by metallic aluminium has been reported by Denny, Robson, and Irwin in two papers. The first was published in 1937; the second, in 1939. The results definitely established that silicosis was prevented in animals by the inhalation of small quantities of aluminium. The present communication records subsequent progress in this field of research.

Jan 1, 1944

This paper reviews hydrometallurgical processing technology for refractory gold ores, which form an increasing resource stock for gold. The reasons fQr ore refractoriness and pressure, chemical and biooxidation process options are briefly listed. Electrochemical technology, suitable for processing refractory ore is reviewed and some preliminary results for the electrochemical oxidation of slurried arsenopyrite are given.

Jan 1, 1992

By Crellin D, Reed SM

The paper presents details of borehole instrumentation schemes for the purposes of monitoring rock and fill deformations associated with groundwater in underground and surface coal mines. The instruments are described which measure rock mass displacements, permeability changes and alterations to hydrology. Methods of installation are detailed and the applicability of instruments discussed. Reduction and interpretation of results are detailed.

Jan 1, 1988

By Partridge AC

The measurement of particle size is very important in many industries. Comments in this paper refer principally to the Mineral Industry and in particular to Coal Mining and Coal Preparation. The objective is to indicate the importance of particle size in process design and process assessment and to describe techniques for particle size measurement and the presentation of results.

Jan 1, 1984

Differences in the assay results of replicate samples engender doubts on the reliability of ore sampling and of assaying procedures. An analysis of variance is a technique to estimate the variability at each level of the procedures. In an example, the variability of one-metre core samples was far greater than that of the assaying technique.

Jan 1, 1976