Search Documents

By Greg Brown

The underwriting of professional negligence has proved to be an evolving science. As with most insurance products coverage offered in the past was very broad but as legal precedent demonstrated to Insurers areas of unforeseen exposure policy documents per se have become more restrictive until today the insurance market through attrition have produced a basic policy structure with various purchasable extensions which together provide insuring professionals with coverage that has proved to be adequate for their needs. The basic policy provides indemnity and protection for fortuitous negligence. In a practical sense, however, professional indemnity policies are really a defence document in so far as policy holders are relying upon the expertise of Insurers to protect them in the event that a claim is made upon them. Whether damages are awarded is in many respects a secondary consideration, the most important factor is to ensure that policy holders are protected in terms of the legal defence mechanism. By way of illustration we are currently in the process of defending a large professional firm which purchased from us a policy with a limit of indemnity of $10M. The case has been running in a Supreme Court now for 14 months and the defence costs which we have incurred on their behalf are rising close to $8M as I put pen to paper. Defence costs of that magnitude would in effect terminally cripple all but the very largest professional operations in Australia. In more recent times coverage has been provided in Australia for breaches of the Trade Practices Act and similar legislation enacted in various States. No-one really appreciated the comprehensive impact which the Trade Practices Act would have on commerce in Australia. Most professionals thought that indeed they would be exempt from prosecution under this Act. The passage of time has clearly indicated that this is not the case and we have found that it is much more difficult to defend a claim involving breaches of the Trade Practices Act than it would be to defend a claim for breach of tortuous liability.

Jan 1, 1995

The following is based on two examples of emission control with coal fired power stations as practised in Germany at Heilbronn Block 7 power station and the Rheinbraun coal combined power station with integrated high-temperature Winkler system (HTW). Heilbronn Block 7 demonstrates the successful emission control of sulphur and nitrogen oxides and the (HTW) system the reduction of the specific carbon dioxide emission. Both were sparked off by legislation which demanded certain emission control standards. Since the early eighties environment protection has been a matter of heated public debate in the European Community. A recent survey in Germany showed unemployment as being the only subject matter more frequently in the minds of people than environment protection. A new kind of forest devastation in areas away from industry has caused investigations by several government departments and private enterprise. Because of lack of conclusive evidence so far, the principle of PRECAUTION has replaced the CONCLUSIVE evidence as a base for new legislation concerning the environment. The new legislative standards for nitrogen oxide emissions in Germany for example have reduced NOx emissions of power stations from 1000 mg NOx per cubic metre of flue gas in the beginning of 1983 to 200 mg NOx per cubic metre of flue gas in April 1984. These new standards were enshrined in legislation when research provided some evidence linking nitrogen oxide emissions through photo-chemical reactions with forest devastation. Thirty European countries signed a treaty in 1983 expressing their concern about air pollution and their willingness to co-operate with each other in controlling large scale emissions.

Jan 1, 1991

Roof bolting with resin bonded bolts has been developed extensively in French coal mines. There are three aspects of this development: 1. The reason for and the care used in the development of roof bolting from use as a reinforcement in a classical arched roadway to use as the only support in roadways in ad- vance of the working face (the roadway being reinforced behind the face); 2. The problems encountered and studied, such as choice of boltable roadways and determination of the technical data in designing a roof bolting pattern; 3. Only because roof bolting has been controlled by safety rules, and especially by accurate measurement of strata behaviour, has this system of support been expanded aapidly in France since 1967.

Jan 1, 1971

By R Rodriguez, S Gumo

The Lihir Gold Mine, in Papua New Guinea, is a large open pit operation within an active geothermal system inside a collapsed volcanic crater. This unique setting has a big impact on the mine operation because of the occurrence of geothermal hazards. The system for managing geothermal hazards that has been developed by Lihir Gold Mine is a pioneering effort that can be applied to future mine discoveries in a similar environment. The controls are integral to the mining operations and allow mining to proceed whereas without them mining could not be considered. Truck and shovel productivities in conventional open pit operations are constrained by diggability, equipment availabilities and utilisation. At Lihir, additional constraints are in the form of 100 m exclusion zones around working shovels and 50 m exclusion zones around working drills. Given that the mine has seven large digging units and six drills, this amounts to a lot of area that excludes the presence of people on the ground. So how are the necessary work like grade control, survey, blasthole loading, and in-pit maintenance performed safely to achieve production targets? The answer is in the highly specialised procedures that have been developed that utilise geological, geothermal and geotechnical knowledge to predict problem areas and also deal with the organisation of movement in the pit for people and mining equipment. This paper will detail how scheduled material movement can be maintained despite the challenging conditions faced at Lihir Gold Mine.

Jan 1, 2007

By Cooke D, Large R

The Cambrian structure in the Mt Read Volcanics was produced by four deformational events: obduction of forearc-derived mafic/ultramalic complexes in the early Middle Cambrian, a middle Middle Cambrian extensional phase related to the post-collisional Mt Read volcanism and VHMS mineralisation, Middle Cambrian E-W folding, and Late Cambrian N-S folding and basin inversion. The major phase of VHMS mineralisation in western Tasmania is restricted to the very brief period of extensional tectonics within the middle Middle Cambrian. Within this period a N-S graben was produced with a complex series of transfer zones, largely striking E-W. Most VHMS mineralisation is restricted to the top of massive volcanic successions, with several mines close to Cambrian transfer structures. Many of the transfer structures continued to be active until the Devonian. The later compressional Cambrian events are not significant in localising orc formation. Within the Rosebery mine a complex pattern of minor Cambrian normal faults has a second order control on the distribution of the mineralisation.

Jan 1, 1997

For the past five years the University of Queenslandhas, through its various workshops, been preaching to Australia that there was a potentially hazardous situation from earthquakes for urban Australia. A few people outside The University accepted this, but largely the warnings fell on deaf ears.The 1989 Newcastle earthquake changed that per-ception. The most important lessons to emerge from Newcastle were (i)the realization that in continental areas small earthquakes cause widespread damage:(ii)the local geology of an area is of great importance in the damage done by an earthquake.These two factors clearly indicate that, in the future, we must take far greater account of the "Urban Geology" of an area. This paper discusses the need for urban geology and its impact on seismic risk and compares that with the traditional methods of assessing seismic risk.

Jan 1, 1990

The Highlands Region of Papua New Guinea has 3 major national highways. The locations of these national highways are shown in Figure 1. The Highlands Highway begins at Lae City on the coast and passes through the Highlands towns of Goroka, Kundiawa and Mt Hagen. It terminates at Togoba approximately 10km out of Mt Hagen town. The Enga Highway begins at Togoba and passes through the towns of Wapenamanda, Wabag and Laiagam. It terminates at the giant Porgera Gold Mine. The Southern Highlands Highway also begins at Togoba and passes through the major towns of Mendi, and Tari. It terminates at Koroba station, near the Hides Gas Field. Two separate Feeder roads intersecting the main highway service both the Kutubu Oil Project and the Hides Gas Field. These national Highways play a very important role in the development of Papua New Guinea. Goods and services are delivered to the bulk of the population of the Highlands Region using these highways. Heavy machinery and equipment for the mining and petroleum projects of Porgera, Hides and Kutubu are transported using these roads.

Jan 1, 1997

From the ventilation aspect, there is a basic difference between advancing and ezreating longwall layouts. Particular rroblems with retreating, using differing mining methods and layouts include high gas emissions, spontaneous combustion and -radients. There is an acceptable method of crntrolling the environment at the return end a retreating longwall face without the use a multiple heading system. Incorporated in the design is the facility to practice xtensive methane drainage, thus ensuring a ntrol of the rate of methane emission into the main roadways. Case studies highlight varying mining editions under which the proposed system of Ctised.

Jan 1, 1982

The overall systems approach to blast furnace aerodynamics is explored including the time and spatial inter-relationships that exist between the furnace lines, tuyeres, burden characteristics, distributor capabilities and furnace operating practice. Attention is called to the time dependent, three dimensional aspects of blast furnace aerodynamics and to the existence of several zones within a furnace where the flow characteristics are different. Changes in furnace operating practice to take further advantage of fully beneficiated burdens including formed coke are discussed from a practical viewpoint. Lessons learned in a variety of shaft furnaces used for other purposes are discussed insofar as they have a bearing on aerodynamics in an iron blast furnace. Questions are raised about the penetration of hot blast in large furnaces. Operating practices and.proposed solutions are evaluated where tuyeres over iron and slag notches are restricted or plugged. Opportunities are presented for using on-line hierarchical computer systems with adaptive tuning algorithms to provide non-linear control of changing process conditions in real time. This will make it possible for the blast furnace operator to optimise a variety of interrelated paramaters, each with different response times. Potential increases in productivity, fuel savings and improved quality control are believed to be within reach.

Jan 1, 1975

Three key areas of C.I.P. plant design, viz. leach- ing time, adsorption and the gold loading on the carbon, are discussed and illustrated with examples. The need for accurate pilot plant data for use in assessing and optimising design is emphasized. This approach should minimize capital and maximise return on capital. It is demonstrated that, as regards adsorption, economics favours short retention time, high gold loadings and mechanically agitated, draft tube reactors. INTRODUCTION Little attempt appears to have been made in Australia to design the present generation of C.I.P. plants to achieve an economic optimum. Most would, seem to have been based on pre- liminary leaching data, gold extraction and value and rule of thumb which, in general, has led to over design and over capitalisation. An essential step to effective economic design is a comprehensive pilot plant study to establish definitive operating parameters, yields and reagent costs. In most cases the cost of developing this data will be more than offset against capital savings in plant; the operating profit should be increased substantially, and profit is maximised for known

Jan 1, 1982

A simple production technique has been initiated and implemented at Oaky Creek open cut coal mine to optimise recovery of coal from the relatively thin geological seams. The production technique is based upon minimising coal dilution through careful dragline operation and the selective use of mine mobile equipment to clean the top of coal. In addition, recovery of coal from the pits has been increased by refining blasting and dragline methods.The implementation of the recovery optimisation programme at Oaky Creek has provided significant economic benefits from increased yield through the preparation plant by the reduction in dilution, and from increased raw coal tonnage through improved pit recovery methods.

Jan 1, 1990

By D Macfarlane, T McMorran

  This paper describes the design and construction of the upper section of the Pike River Mine Access Road. The road extends 11 km from Logburn Road alongside Big River on the West Coast of the South Island of New Zealand up Pike Stream to the new mine portal on White Knight Stream (Figure 1). This new road starts on alluvial terraces, then partially follows an old logging road before entering virgin bush and traversing the true left bank of a steep sided gorge on Pike Stream some 50 - 100 m above the stream before dropping down to the mine entrance. Its development has been an extended process from route selection, consenting through to design and construction.   The paper focuses on the 1 km section of road between the Amenities Area (Figure 1) and the portal. This section of road is a steep section through the gorge, principally on Conservation estate, and has presented the most challenges and required the greatest effort to obtain the regulatory approvals, prepare the design and to construct. This paper outlines the history of the challenges faced and how the road was successfully developed.

Jan 1, 2007

The objective in design of an excavation in a jointed rock mass is to achieve a prescribed degree of control of rock mass displacement around the excavation. Any excavation in jointed rock usually involves slip and separation along discontinuities as well as translation and ro- tation of constituent rock blocks. Thus, any acceptable model of behavior around an excava- tion must be capable of simulating the force displacement paths followed by the constituent elements, including rigid body translation and rotation. The distinct element method models such behavior by simulating the rock mass as an assemblage of rock blocks which interact through corner and edge contacts. Discontinuities are regarded as boundary interactions between blocks with joint behavior prescribed for these inter- actions. Introduction of structural element logic allows a variety of installed support sys- tems to be modeled. The response of the support to axial, transverse, and flexural loads is based on explicit algorithms similar to those used in the distinct element formulation. This allows large displacements and rotations and general non-linear constitutive behavior for both the support elements and the interface with the rock. This paper describes both the distinct element and structural element formulations and demonstrates several applications involving sup- port interaction with jointed rock.

Jan 1, 1987

Grey River Gold Mining Ltd commenced dredging alluvial flats in the Grey River Valley in 1989.Previous drilling indicated over 100 million cubic metres of gravels with some 90% of the gold in the bottom 7 metres.The dredge built by Rahco, Spokane, was innovative in a number of aspects but particularly in the fact that a separate ladder with a cutter and pump was used to strip the overburden and a bucketline to mine the gold bearing wash below.Metallurgical studies and exploration were initiated when the project commenced; Leasing and environmental considerations were investigated and action taken.While progress is being made, the operation at this stage is not meeting required production and performance. Main problems have been with the stripping system and wear.

Jan 1, 1990

There are a number of factors affecting the discovery and develop- ment of uranium in Australia which makes this mineral almost unique and quite different from other minerals. I. The role of the Australian Government, which initially encouraged the discovery by offering rewards to prospectors who discovered deposits that could become economic. 2. At a later stage, the Commonwealth and South Australian Govern- ments prevented the development and production of "new mines" by refusing to grant mining title and refusing to allow sales of uranium by not issuing export permits. 3. The unique property that uranium and its daughter products possessed, i.e. radioactivity, meant that any person who purchased a geiger coun- ter could go prospecting, even though they had no previous experience in prospecting and they had an equal opportunity of discovering a new deposit as a company or independent geologist. 4. Because the exploration/demand for uranium didn't occur until the 1940s very little background geological information or models were available and so the early discoveries tended to become the locus for exploration rather than moving into areas which might on geological concepts lead to exploration programmes based on geological models. Because of the lack of knowledge there was the exchange of geologists from the U.S. Geological Survey and the South Australia Geologist Survey.

Jan 1, 1988

Production implications of the introduct- ion of electric L.H.D. units in sublevel open stoping and pillar recovery at Rosebery are covered by Faulkner (1982) and Carlton (1982). The following engineering aspects associated with the decision to introduce electric L.H.D.'s are considered here: - Initial requirements for commissioning, including power reticulation at an adequate level to all operating areas. - Conversion of a manual system to radio remote control. - Maintenance backup requirement to ensure that the production potential is realised.

Jan 1, 1982

By G Gibson, B Bessen

In coal preparation, large dense medium cyclones (DMC) at low pressure heads (typically 9D where D = cyclone diameter) are the norm. This contrasts with high density mineral applications where, largely for historical reasons, smaller cyclones at high heads are the standard. There are advantages in preferring large diameter cyclones at low heads, assuming that metallurgical performance does not suffer significantly. These include simpler plant layouts, easier maintenance, smaller spares inventories, reduced wear, reduced medium pumping demands, smaller buildings and overall lower capital and operating costs. In 2008, therefore, Xstrata Zinc decided to trial a single DSM-design 800 mm cyclone in one of its four DMC lines at Mt Isa, replacing the four 400 mm cyclones previously installed. Circumstances allowed a low head of 9.5 D to be trialled, compared with the existing 400 mm head of 21.5 D. This paper describes the trial, including tests using painted ore particles as tracers, estimates of yield and metal recovery, and wear monitoring. The larger unit performed well. There was no evidence that metallurgical performance in terms of metal recovery and waste reject rate suffered, and there was some evidence that it may have improved. Cyclone life increased, and preliminary data suggest that the replacement cost of the 800 mm cyclones is less than half that of the 400 mm units, and this is expected to improve. The plant layout and operability have also improved significantly. Xstrata has therefore decided to convert the whole plant to four low head 800 mm units, replacing the original 16 high head 400 mm units. The paper includes an explanation of the effect of static head on DMC separating force. It also reviews earlier research on diamond applications, and applies a general DMC process model to the Xstrata case, both of which confirm that large, low head cyclones are appropriate in mineral applications, contrary to conventional practice. Such units could significantly reduce both the capital and operating costs of DMC plants in mineral applications.

Jan 1, 2009

By P Griffin

Mill relining is a major contributor to overall plant downtime. Reducing the number of mill liner pieces removed from and replaced in the mill has a direct impact on the overall reline time and in turn, mill availability. To improve the mill availability of Ridgeway OperationsÆ 32 foot SAG mill, a number of initiatives were implemented in terms of liner design. These included the conversion of the shell from 40 to 30 rows, reducing the number of pieces from 80 to 60 each shell reline and reducing the number of pieces from 48 to 32 per feed end reline. In addition, modifications were made to the discharge end of the mill to extend the life of the outer pulp lifter and discharge cone, thereby reducing the frequency of change out. The standard radial outer pulp lifter was converted to an angled design. The discharge cone was converted to the BullnoseTM design supplied by Bradken. This paper discusses the design changes made and the expected benefits to the Ridgeway Operations in terms of mill availability improvements.

Jan 1, 2007

The large rotary blast hole drills for hole sizes of 250 to 375 mm in diameter have been utilized by large open pit metal and coal mines for production drilling all over the world. The design of such rotary drills is in most cases about two decades old and it has not been done much in order to apply a modern technology on rotary drilling. The most modern large rotary drill, Tamrock RI 10, consists of an advantageous rotary head with a squirrel cage AC motor controlled by a frequency converter, a beneficial mast structure with a possibility for inclined drilling, hydraulic driven, independent crawlers, and a modern ergonomic cabin to provide a comfortable working condition for the oper- ator. Several automatic features are available as options. The rig has been designed to be operated by one man only. With this modern rig the produc- tion rate can be increased and production cost kept on a low level.

Jan 1, 1989

By Schofield D, Denby B, Stout F, Moli A

This paper documents the development of a user-friendly computational program, which has been constructed to assist the mine ventilation engineer in the optimal design and operation of methane drainage ranges. In the past, many computer tools for ventilation engineers led to the development of `research systems'. These computer systems, although developed with the needs of the industry in mind were due to a combination of inexperienced programming methods and the availability of suitable user interface software not easily accessible to the practising engineer. Recent developments in computer hardware and software (particularly windows based graphical user interfaces) mean that engineers no longer need to dedicate large amounts of valuable time to become familiar with often complex items of software. The authors of this paper intend to demonstrate a practical system which successfully integrates complex mathematical models, an easy to use interface and knowledge based techniques. The graphical interface guides the user to draw on the screen a mimic diagram representation of the methane drainage network. The user is prompted, during the construction of the drawing, to input the information and data required by the calculation and knowledge based procedures. The computer program then calculates all of the flows, purities and pressures throughout the network. Given reliable measured data from an existing range a comparative analysis can be performed between the predicted and measured network flow data. A knowledge-based system may utilise this analysis to either update the operational status of the network or suggest either a reasoned maintenance or remedial strategy to improve the performance of the drainage system. The development of the OMEN project has been carried out at the request of the Midlands Group, British Coal Corporation, Edwinstowe. The system is about to be field tested at a number of mines. It is hoped that when this paper is presented that the system will be used at both Group and mine level.

Jan 1, 1995