Search Documents

The Mt Whaleback open cut mine South Wall is, in part, developed as an unbenched dip slope. The remainder of the rock slope consists of asymetrical overturned folds which have been locally truncated by major low angle faults. The Mt Whaleback orebody is structurally controlled and therefore extensive structural geology input has gone into the final rock slope design. The design is based on normalised 40 m geological cross sections, but the inherent complexity of the geological structure of the orebody yields a high degree of uncertainty within that interval. There- fore, the final slope bench face and the penultimate bench faces are mapped in detail to accurately establish the geological contacts and struc- ture. The knowledge of accurate geology of final and penultimate faces plays a very important role in the design of controlled perimeter blast- ing. Accurate geology is established mainly by face mapping, and by hole geological evaluation of blastholes to locally refine the current Geologi- cal model.

Jan 1, 1989

Excavator output rates given in Makers' catalogues are sometimes based on favourable operating conditions. Mine operators and planners are more interested in the Effective Hourly Output in normal operation (Qe) a plant system can give hour by hour and year after year in a particular application. The number of hours mining plant will be available for normal operation will be less than the annual total of 8760 h. The number of the available hours which can be utilised at Qe will depend largely on the number and types of units in the plant system, the manners in which they are applied and the nature of the deposit in which they work. The emphasis herein is on continuous systems for deep stripping with BWE's as the primary excavator. Examples and suggestions are given for the annual hours at Qe for some BWE systems.

Jan 1, 1981

At the beginning of the seventies pre- drainage of methane was introduced in West German coal mining in order to reduce the gas emission from the worked seam. After three pilot tests on the "Rheinland" Colliery (86 boreholes in seam "Prasident"), "Bergmannsgluck/ Westerholt" Colliery (23 boreholes in seam "Gustav") and "General Blumenthal" Colliery (27 boreholes in seam "Hugo" and 170 boreholes in seam "Karl") systematic large scale tests with extended investigations were carried out un the "Rheinland" Colliery (127 boreholes in the seams "Anna", "Blucher", Prasident"). During this time an analogous test was carried out on the "Consolidation" Colliery (21 bore- holes in seam "B"). In these studies and tests the technical feasibility, efficiency and economy could be proved, so that pre-drainage of methane starts spreading. On the "Rheinland" Colliery pre-drainage has become common practice in gassy seams. Mainly two points impede a faster spreading of method: 1. in many cases the necessary requirement, that one or both of the gate roads should ire driven 6 to 12 months before the face is worked, is missing. This is mainly due to the difficulty of retreat mining in passe seams.

Jan 1, 1982

By M P. Murphy, C M. D Barton

When developing a new underground mine, the geological interpretation that guides the mineral resource is crucial to the preparation of a reliable ore reserve. In preparing a robust geological model to underpin a resource estimate, practitioners must weigh the comparative risk of accepting a relatively wide-spaced drill hole pattern, versus a more close-spaced pattern that ensures a high local geological confidence for mine planning but may have an exponentially increased time and monetary cost. This paper details the authors’ investigations into the geological uncertainty of IGO’s Odysseus Deposit, which is approximately 645 km north-east of Perth, Western Australia. At Odysseus, the komatiitic nickel sulfide mineralisation is irregularly cross-cut by nickel-barren pegmatites that have intruded and offset its thick ultramafic orebodies. These pegmatites generate significant uncertainty in the precision of Odysseus’ resource volume and tonnage estimates, as well as the subsequent quantification of pegmatite mining dilution in its ore reserve. To quantify the geological uncertainty in the pegmatite interpretations, IGO’s mineral resource practitioners prepared several geological risk studies over the Odysseus North lode, which is the lode most affected by the pegmatites. These studies included categorical conditional simulation of the pegmatites, preparing implicit geological models with alternative algorithms, trialling a machine learning application to prepare a maximum likelihood geological model, and finally assessing the early results of the pre-production close-spaced drilling to these different models. To assess the precision of the different single-outcome models, the authors’ compared the estimated pegmatite content of each model to the range of possibilities modelled by categorical conditional simulation within the planned stopes at Odysseus North. An estimation confidence score for each modelling method was then prepared for each alternative single-outcome modelling method. From these studies IGO concluded that a close-spaced drill pattern is essential at Odysseus, supporting the view of the Competent Person in 2017 who proposed a 25 m drill spacing in areas affected by pegmatite which had been partially classified as Inferred.

May 24, 2023

By M Wen, J Gerit, C A. Pelletier, D Muggli

On-land waste rock dumps at BHP Billiton Base MetalsÆ Island Copper Mine (ICM) near the northern end of Vancouver Island, B.C. continue to discharge ARD. These waters, which amount to approximately five million cubic metres each year, are injected into a three-layer, meromictic pit lake for treatment. The top layer is brackish water, replenished by each yearÆs rainfall (amounting to nearly 2 m/year). This top layer of water must meet effluent permit limits for heavy metals. This water eventually exfiltrates through a æbeachÆ waste rock dump, which is 93 per cent submerged along the north shore of Rupert Inlet. The middle and bottom layers of the Pit Lake are saline and currently oxic (2 mg/L dissolved oxygen) and anoxic (0.03 mg/L dissolved oxygen), respectively. Spreading of a liquid fertilizer every ten days throughout the top layer results in plankton and bacterial blooms that scavenge zinc, copper and cadmium out of this layer eventually to become mineral sediment in the bottom of the pit lake. Adsorption on planktonic skeletons and mineral precipitates also scavenges these dissolved metals from the middle and bottom layers to form bottom sediment. Sulfate reduction has recently begun in the bottom sediments. Diagenetic processes in the bottom sediments will eventually transform most of the dissolved heavy metals into insoluble sulfides. Cycling of ferric iron between the sediment and the water column and back seems to contribute dramatically to the biogeochemical metal removal processes. This biogeochemical system serves to maintain the top-layer water well within permit limits for discharge to the environment.

Jan 1, 2003

By Thompson M

The humble gabion basket is to mine development what the light bulb and safety pin are to eir-ryday life. Gabions provide a flexible, easy to assemble and cost efficient solution for "101" mine and civil engineering development applications.In some instances gabion baskets are still efficiently in use after many years of faithful, maintenance-free service. In other situations, the baskets have been demolished or made redundant within days, either having served their temporary usefulness or negligently destroyed by the operator of heavy equipment. Either way, the gabion basket must surely rate among the top 10 cost efficient engineering construction materials.

Jan 1, 1994

By J F. Colinet, G, J A. Zimmer, R J. Timko

It has long been known that ventilation is a cost-effective method to lower respirable dust concentrations in all types of mining applications. The National Institute for Occupational Safety and Health has been working on a number of different research techniques that use ventilation as a critical component to lower respirable dust levels at surface and metal/non-metal operations in the United States. This article presents five such research efforts. The first research area discusses how improving the ventilation flow patterns in an iron ore mill facility lowered respirable dust concentrations by 31 per cent throughout the primary grinding area. The second research area examines how respirable dust levels were lowered at a dimensional stone shop by using air cleaning units suspended from the ceiling. A third area discusses how improvements in ventilation at underground limestone mines lowered respirable dust concentrations. The fourth area examines how improvements in dust filtration and pressurisation systems significantly impacted the air quality in enclosed cabs of surface mining equipment. The last area presents a newly developed clothes cleaning technique. This technique uses an air spray manifold to blow dust from a workerÆs clothing in an enclosed booth, which confines the dust for capture and removal by a baghouse dust collector. These research areas represent an array of different control technologies to lower respirable dust concentrations. Ventilation is an integral part of these control technologies.

Jan 1, 2005

By Kristiansen J

A series of laboratory blasting and ball mill grinding tests have been done on four different types of hard and competent rocks. The results show that exposing these rock types to a higher level of explosive energy will enhance their grindability. True blasting optimisation should therefore look at the whole comminution process from solid rock to a marketable product.

Jan 1, 1995

By D J. Brake

The importance of mine ventilation to health and safety in both coal and metalliferous mines has been long recognised. The primary and secondary ventilation systems in most metalliferous mines incur 50 per cent or more of the total mine electrical power consumption and frequently about 10 per cent of total underground mine operating costs. The requirements for ventilation-related horizontal and vertical development, fans and cooling have a significant impact on mine capital costs and also on mine schedules and start-up times and hence cash flows. There are increasing pressures on regulators and miners to reduce airborne contaminants such as diesel particulatematter, nitrogen dioxide and heat (wet bulb temperatures), and significant pressures to reducegreenhouse gases such as fugitive methane emissions from coalmines and the carbon dioxide footprint of both coal and metalliferous mines. Many previously Australian miners are now globaloperators and have extensive overseas mining operations where local ventilation standards and expertise may not be consistent with Australian practices. The role of the site ventilation officer is also changing with strict new requirements for the statutory position being introduced into Queensland metalliferous mines and the potential for this to become more widespread. Recent regulator and parliamentary review committees have identified systematic shortcomings in mine ventilation compliance, and statutory certificates in both Queensland and NSW now require continuing professional development to maintain currency. Public and investor support for mining are also increasingly contingent on safe, healthy and environmentally responsible practices and the standards for these are frequently tightening. Good ventilation design and operating practices that are consistently well executed therefore contribute significantly not only to a safe and healthy mine but also to a productive and cost-effective operation and the ongoing social licence to operate. There are a variety of ways of providing technical design and oversight into a mine’s ventilation systems; this paper explores some current trends in ventilation standards and statutory requirements, as well as ways to support and develop mine ventilation staff for both domestic and international operations and also the emerging senior technical roles of Group/Principal/Corporate mine ventilation engineer.

Oct 12, 2022

By Bennet A. G

An overall review of the selection of rock strength and deformation characteris- tics for the design of the Melbourne Under- qround Rail Loop (MIJRL) rock tunnels is presented. Particular emphasis is placed on aspects of in-situ testing, including large diameter plate bearing tests. Material on the interpretation of test results for use in the design of the tunnel linings and openings is included, with a brief discus- sion of desiqn methods.

Jan 1, 1981

By Z Gao, D Liao, W Sun, S G. Pooley, J Wang, Z Shi, G Jing, S Ren, Q Chen

Yuanjing processing plant is a scheelite and wolframite plant in southern China. Water shortages and recent environmental regulations mean that the plant must reuse the wastewater that comes from the mining operation. This paper describes the efforts to reuse the mining and ore washing wastewater (MOW) in the processing plant. Initial attempts to reuse the MOW in the strong magnetic separation were unsuccessful because the magnetic media pack was seriously fouled by the micro-fine precipitate generated. The focus changed to reuse the MOW in the scheelite flotation circuit, which includes one roughing, one cleaning and three scavenging steps. Laboratory batch tests showed this would likely be successful because using MOW reliably improved the flotation performance in the laboratory tests. Then a 20 day industrial trial was run in the plant. The trial was very successful with the enrichment ratio of WO3 increasing from 17.4 to 23.6, while the recovery remained around 79.2 per cent. The industrial trial was so successful the company immediately adopted the new scheme, which has remained in use ever since. This technical solution not only alleviated serious water shortages, and satisfied environmental regulations but also improved the plant performance.

Aug 24, 2022

Automatic sampling and weighing of copper sulphide concentrate produced on Bougainville Island (PNG) is described. Contained metal weights gave satisfactory agreement with buyer's results after the introduction of polyethylene lined sealed aluminium foil bags for transport and storage of assay samples. Paper bags used previously for this purpose permitted oxidation of the sulphide concentrate and thus caused lower assay values.

Jan 1, 1976

Data logged on mineral beneficiation processes during normal operation are analysed using time series (correlation and spectral) methods to identify the dynamics of the processes for on-line computer control. Recursive least squares estimation techniques are used to identify parametric models for a cassiterite flotation circuit and a coal washery. Identification problems such as the determination of model order, process time delays and the 'contamination' of the data by process recycle streams (feedback) are discussed. Typical results are presented in which optimised models are identified from data logged during normal operation.

Jan 1, 1985

By A Jewbali, R Perry, R Inglis, L Allen

"The use of conditional simulation to characterise mine plan uncertainty is increasing for the assessment of risk in mining projects. While the development of grade uncertainty profiles is relatively straightforward and can be validated using standard geostatistical techniques, the addition of geological uncertainty to evaluate total risk remains problematic. Some of the problems associated with geological uncertainty methods include the clustering of data in favourable geologic units, difficulty in training image definition and the inability to address change of support issues for categorical variables. Despite these obstacles, the importance of geological uncertainty as a contributor to total uncertainty has prompted Newmont to explore and evaluate the use of various techniques (and combinations of techniques) on different deposit types.Two orogenic deposits of different geological complexity were selected for the study: Subika, a shear zone-hosted deposit, and Merian, a deposit containing gold mineralisation associated with quartz vein zones and stockwork within which are found higher-grade quartz breccia zones. Newmont trialled various categorical simulation approaches to determine the applicability of these methods for each deposit type and the effect of parameter choice on the width of the uncertainty interval. Some of the techniques that were trialled include multiple point statistics methods, sequential indicator simulation using local probabilities as well as variations of these methodologies.The goals of this study included: gaining an understanding of which techniques may work best in which deposit types gaining an understanding of the intricacies of each method gaining an understanding of the effect that each method has on total uncertainty analysis.This paper presents a comparison of the various techniques and makes recommendations for their use in uncertainty analysis.CITATION:Jewbali, A, Perry, R, Allen, L and Inglis, R, 2014. Applicability of categorical simulation methods for assessment of mine plan risk, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 85–98 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014

By A Fyans, B Ghahreman-Nejad

This paper discusses the method and results of an options study into selection of the optimal form for a 130 m high tailings/water retaining dam, located in a region of high seismicity in central Iran. The proposed dam is part of a planned expansion project for Sarcheshmeh Copper Mine (SCM), which after construction will provide 550 million tonnes of additional tailings storage over the next 27 years. Geotechnical investigation at the proposed site indicated that adequate suitable low permeability materials (i.e. clay) were not available in the immediate vicinity of the dam site and would need to be imported from a distance of well over 10 km (direct). Given the magnitude of the estimated quantity of material and construction cost it was considered prudent to compare the cost of alternative dam design options for the proposed storage. A total of five dam design options are considered including a conventional rockfill embankment dam with an upstream sloping earth core (ECRD), a geomembrane face rockfill embankment dam (GFRD), a sloping asphalt core rockfill embankment dam (ACRD), a roller compacted concrete dam (RCCD), and a filter rockfill embankment dam for tailings storage together with a separate smaller earthfill core rockfill dam (ECRD) located downstream for storage of decant water. The risks, costing and design of all options are discussed in detail and the outcome of the study is presented.CITATION:Ghahreman-Nejad, B and Fyans, A, 2018. Optimum embankment design for a tailings dam, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 427–438 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By P Radulovic, V Lawson, M Muller, J Wallace

The Mount Isa Copper Concentrator was commissioned in 1973. Since commissioning some significant upgrades have been undertaken such as: • the replacement of the rod mill/ball mill circuit with AG mills and the subsequent conversion of the AG mills to SAG Mills. • the introduction of columns as retreat cleaners in 1987, then reallocated as prefloat cleaners in 1994 and rougher cleaners in 1996.• the repurposing of some rougher capacity to preflotation roughing to remove carbonaceous pyrite and talc in 1994.• the introduction of a Jameson Cell for preflotation cleaning in 2000. • the expansion of the rougher and cleaner circuits in 2002 with the inclusion of 6 x 100 m3 Wemco cells to replace the capacity lost to preflotation and to increase residence time and improve recovery. In 2013 work commenced to replace the cleaner circuit after 40 years of operation. The new cleaner circuit, consisting of 3 x B5400/18 Jameson Cells, replaced the rougher cleaner columns, cleaners, recleaners and retreat Agitair banks and was commissioned in Sep 2015. The new cleaner circuit was configured as two cells in series producing the final concentrate and a cleaner scavenger cell to supplement the existing Wemco cleaner scavenger cells. The performance of the new circuit is discussed.CITATION:Lawson, V, Muller, M, Radulovic, P and Wallace, J, 2017. Mt Isa copper concentrator cleaner circuit redesign, in Proceedings MetPlant 2017, pp 279–287 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

Mt Todd lies towards the south end of the Pine Creek Geosyncline, sandwiched between the Cullen Batholith and the Edith Falls Basin, in an area of regionally metamorphosed sandstones, siltstones and shales. The Batman deposit, some 3 km west of Mt Todd is a sheeted quartz vein system hosted within greywackes of the Palaeoproterozoic Burrell Creek Formation (Finniss River Group). The gold-bearing quartz veins, trending 010¦-020¦ and dipping 60¦-70¦E, are commonly 0.5 to 5 cm wide and occur at intervals which are from 10 cm to 1 m apart. Gold tends to be restricted to the quartz veinlets and immediately adjacent country rock. Grade Control utilises two 4 m 'collar' samples which are collected from each 8 m production blasthole. The irregular distribution of the quartz veins and erratic gold mineralisation has resulted in a disseminated 'salt and pepper' type of gold occurrence, with only a poorly defined footwall. Delineation of ore and waste blocks for mining uses an approach which combines the smoothing effect of kriging with a pragmatic view of the raw data. Large ore blocks with simple geometry help to minimise mining dilution, reduce block variance and give good reconciliations to interpreted ore tonnes and grade. Daily mine face advance is reported against truck counts and provides continual comparison with budgeted production. All data processing uses Gemcom software, together with Lotus spreadsheets.

Jan 1, 1994

By Y M. Wang, W Z. Liu, L F. Li, X L. Zhang

Based on the blasting crater theory, the equation between k under typical cases and burden line, charge height was obtained by open pit bench blasting analysis model. The model was calculated with mine production blasting. The blastability coefficient k and the best range of blasting burden line were specially emphasised on determination of lateral crater tests.CITATION:Wang, Y M, Liu, W Z, Zhang, X L and Li, L F, 2015. Application of lateral crater test in open pit blasting parameters optimisation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 463–468 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Distin P. A

The extraction of platinum and rhodium from scrapped honeycomb autocatalyst into hydrochloric acid/aluminum chloride/nitric acid solutions is described. Results are given for the effects of leachant composition, temperature and catalyst pre-reduction using hydrogen. Data are also presented for the recovery, by hydrogen reduction, of platinum and rhodium dissolved in the leach solution. Parameters studied include solution composition and temperature, hydrogen pressure, and platinum seed addition.

Jan 1, 1992

By G D. Matthews, M E. Haylett, S Khosrowshahi, A Weeks

In narrow orebodies the use of ordinary kriging (OK) may pose certain limitations when used for grade control modelling. The smoothing effect of kriging, by its very nature, cannot retain or accurately characterise the dispersion (variability) that is inherent in gold deposits. This dispersion is a critical component of determining the desired level of ore loss and dilution.Fixed block model positions used in OK, and all estimation approaches, within a grade control process may never align with the ‘true’ ore boundary. This may lead to excessive ore loss and dilution, especially within narrow lodes.Using a risk-based approach to ore block design based on the geostatistical method of conditional simulation (CS) can highlight the differences achieved when an alternative method to OK is used for grade control modelling. By using a mesh of nodes and the application of a ‘transfer function’ to the simulation models, the position for ore contacts can be better assessed than when using fixed blocks in OK. Therefore, the value of various ore block boundaries can be better analysed by objective assessment of ore loss and dilution for a given minimum mining selectivity (selective mining unit or SMU), even in narrow lodes.A case study of a narrow vein gold deposit, comparing the results from an OK model and a CS model shows that whilst both models show similar trends – waste, low-grade, and high-grade regions are the same in both cases – the simulation model can provide greater insight for optimal definition of the mineralisation boundary.CITATION:Haylett, M E, Weeks, A, Matthews, G D and Khosrowshahi, S, 2014. Ore block design in narrow vein gold deposits – estimate or simulate?, in Proceedings Ninth International Mining Geology Conference 2014 , pp 421–424 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014