Search Documents

By G R Ryan

Recent events have raised the issue of whether, and if so when and how, an explorer may gather data from a mining tenement or permit which is held under the relevant mining Act by another party. Two situations arise: that of the small operator who wishes to prospect, and if successful mark off, ground held by others by virtue of the local form of exploration permit; and that of a regional explorer who may wish to enter on to some one else's existing mining tenement within the region of interest. The legal situation varies from state to state. At present the broad consensus seems to be that, provided consent is given, small-scale prospecting on another's exploration permit is at least tolerated if not actually provided for by the relevant Act. Entry onto a granted tenement to carry out any form of exploration is, however, prohibited in all jurisdictions unless consent is given. Furthermore it would appear that the proposal and conclusion of a joint venture agreement places certain obligations upon the party proposing to carry out exploration. These conclusions apply where ground surveys are proposed. Where data acquisition is by aerial survey the situation is much less clear, principally it would appear, because up to now little thought has been given to it. If trespass applies at ground level, at what height does it cease to apply? Can aerial magnetometry or photography be classified as prospecting? Is there an obligation upon public authorities who carry out remote sensing to make data available to the holders of mining tenements within the surveyed areas? Moves are now afoot to address these and other considerations, and it would be in the interests of everyone if a national approach to the problem could be adopted from the beginning. Certain suggestions in this respect are put forward.

Jan 1, 1994

By M Gao

Six new IsaMills were installed for the George Fisher flowsheet in the Lead/Zinc Concentrator of Mount Isa Mines to produce a product P80 as fine as seven microns. The objective was better liberation of galena and sphalerite. The IsaMill commissioning was completed by the end of 1999. The six new IsaMills were running to the metallurgical specifications almost immediately after start-up. This paper reports the performance of the George Fisher IsaMills in the zinc circuits and some of the latest development in the IsaMill designs and maintenance during George Fisher commissioning.

Jan 1, 2000

By Enever JR

In-situ rock stress measurements conducted in the Phillipines and on Bougainville have revealed stress fields significantly different from expectations based on intraplate experience. The results have potential significance in regard to both engineering practice in the Pacific Rim region as well as in helping to understand the geological processes occuring near subduction Zones.

Jan 1, 1987

By B Johansson

The mining industry needs to recruit young talented people. An important task therefore, is to create future attractive mining workplaces that engage and motivate young people to work within the industry. Our intention with this article is to illustrate a possible way forward for the mining industry to form such workplaces. We discuss different aspects of an attractive workplace and summarise our findings in a specification of basic demands dealing with safety, physical and psycho-social work environments and social responsibilities.

Nov 22, 2011

By Yinxiang W, Chunlai Y

In older to improve efficiency of surface pre--grouting in sealing off water in heavily water-bearing strata, such as sandstone,siltstone and limestone, several methods have been used in China, they are ; intermittent pre-grouting, adjusting pre-grouting parameters and stepwise repeated pre-grouting methods. The paper describes effect of deviation on water sealing in pre-grouting. Deviation correction measures, like mechanical, technological and changing hole position methods have been introduced with satisfactory results in practical engineering projects without increasing the volume of engineering project and without causing delay.

Jan 1, 1988

By A Bonani, R Molina, H Constanzo

With conventional undercutting sequence the infrastructure on the production level often has a short serviceable life before major rehabilitation is necessary and is characterised by high maintenance costs. The abutment stress zone is the main cause of this situation. The application of the pre-undercut caving method variant can increase the availability and utilisation of the production level When a pre-undercut is used development and construction are carried out underneath a previously undercut area, far away from the abutment stress zone, under more favourable stress conditions. This paper describes the design principles and the relevant results from the application of the pre-undercut variant over three years to the Esmeralda sector of El Teniente mine. The aspects described are the undercut-extraction, the undercut-development and construction distances, the geometry and drawbells opening, cave extraction rates, and the rate and height of undercutting.

Jan 1, 2000

Recent analysis of backfilling material has shown that a finer size distribution is preferable for stope filling. In order to increase crusher throughput and pit productivity, a reassessment of the quarrying operation was conducted. Part of that reassessment was a review of blasting practice. Six means of reducing the average muckpile fragment size were examined. Different blast initiation and charging options were compared, and patterns using smaller hole sizes were designed, analysed with the JKMRC 3x3o software, then drilled and fired. The ground vibration and face movement was recorded and compared. To determine whether the Kuz-Ram model could be used in an economic analysis of the quarry operation, the fragmentation distribution of the small diameter hole blasts was determined. Photographs of the muckpiles were taken and digitised. However subsequent analysis indicated that a satisfactorily large photo sample was only obtained from the smallest diameter hole blast. The Kuz-Ram fragmentation model prediction was found to be within the confidence limits of those results. An engineering and cost comparison between the blasts was made.

Jan 1, 1995

Between, 1980 and 1984, the demand for non- ferrous metals in the free world grew annually by 1.5 per cent for copper, 0.4 per cent for lead, 1.4 per cent for zinc, and 2.5 per cent for nickel. The growth rate decreased substantially compared to the rate experienced before 1980, and was far lower than the GNP growth during the corresponding period. The main reasons for this are considered to be 1. resource-saving efforts by industrialized countries resulting from the first and the second oil crises, 2. saturated demand for durable consumer goods, and 3. substitution of non-ferrous metals by new materials such as optical fibers.

Jan 1, 1986

Early in 1950 a new laboratory was set up to deal with problems in mineragraphy, petrology and metallography. This paper describes the equipment, the organisation and association of the laboratory with the various departments of the company, the work that has been done and future plans.At Mount Isa it was soon realised that the microscope would play a most important role in mineral dressing problems and aiding geological research.As early as 1928, R. J. Colony submitted a petrographic report on Black Star ore for Consolidated Limited; much later, in 1934-5 Dr. Grondijs published for Mount Isa Mines Limited a preliminary study of the Mount Isa orebody, followed by a mineragraphicinvestigation of mill products, and in 1937 a Study of Mount Isa Ores by H. GrondIjs and C. Schouten appeared in Economic Geology, for June-July. Other papers dealing with the petrology and mineragraphy of Mount Isa ores are appended at the end of the paper.The mill research metallurgical staff has endeavoured to incorporate mineragraphy in solving milling problems and determining the effectiveness of laboratory as well as examining minerals sent in by the geological department.For many years the amount of equipment available was limited and much of it was locally made or improvised. An improvised briquetting machine, and grinding and polishing lap gave moderate results in conjunction with an old, but serviceable, Leitz microscope. However, for more detailed and accurate work not possible with improvised equipment, many mineragraphic problems were sent to specialist in.

Jan 1, 1953

Ore sorting is a high capacity, low cost method of preconcentrating ores and in some cases of producing a marketable concentrate. In most cases it is applied to run of mine material, immediately after primary crushing and screening in sizes ranging from 10 mm to 150 mm. Recent developments in bulk sorting of friable uranium deposits have resulted in machines capable of handling fine materials with sensing and separation being achieved on a zone by zone basis. Modern ore sorting machines rely on the synchronous operation of four internal sub systems, feed presentation, sensing, data processing and separation. A variety of different sub systems is available which can be combined in various forms to produce sorters capable of handling a wide variety of mineral types. The benefits in using ore sorting cover a wide range of situations and are applicable to both established mines as well as new mining ventures. Reduced operating costs, increased productivity, capital savings, energy and resource conservation and environmental issues are all part of the reason why ore sorting is finding rapid acceptance in today's mining industry.

Jan 1, 1980

By Weller KR, Restarick CJ, Stewart PSB

Following a detailed assessment of concen trator performance at Broken Hill South Limited which was reported in a previous paper, the fine grinding section was changed from a parallel arrangement of the two grinding circuits to a series arrangement, and the concentrator per- formance re-assessed. The change to series grinding had virtually no effect on the actual or potential capacity of the circuit to make a final product with 80% passing 100 mesh. However, the fresh flotation feed contained significantly less +150 mesh lead and +65 mesh zinc (material which was shown to float poorly), without an increase in the quantity of poor-floating ultra-fine lead and zinc. From the size-by-size flotation recovery data, it was shown that overall recoveries of both lead and zinc were approximately 1% higher than they would have been without this change in size distribution and it was concluded that this was a direct result of the change in grind- ing procedure.

Jan 1, 1972

By J Arif, J Proffett

Copper and gold mineralisation at Batu Hijau is directly related to quartz veining and wall rock alteration that developed in close spatial and temporal association with multiple tonalite porphyry intrusions. To its advantage with respect to the study and better understanding of the evolution of the porphyry system, Batu Hijau has comparatively minor late alteration and mineralisation overprints. This paper summarises results of detailed geological logging, petrographic studies and geochemical analyses of diamond drill cores from the deeper sections of the Batu Hijau porphyry system (ie its roots). An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

Renison Limited produces high and low grade tin concentrates at an annual rate of 5000 tonnes of contained tin metal. In spite of the fine average cassiterite grain size, emphasis is placed on gravity concentration methods to produce a high grade final product. Cassiterite flotation is considered and operated as a gravity circuit scavenger responsible for approximately 15 percent of recovered tin metal as a fine grained low grade concentrate. Metallurgical problems mainly result from ore-type variations which may be aggravated by a number of circulating loads. The rationalisation of circuitry is being studied to provide more effective control by operators and to allow exploitation of current control and modelling techniques.

Jan 1, 1977

By Nickelsen J, Theisen KG, Hansen PH

The use of stationary calciners in the processing of aluminium hydroxide has emphas- ized the importance of Bayer hydrate properties with respect to particle breakdown during calcination and subsequent treatment. Test results from calcination of several Bayer hydrates to sandy alumina in the FLS Gas Suspension Calciner (GSC) were obtained in a 250 kg/h pilot plant unit. Particle breakdown during calcination was influenced by content of solid sodium oxalate, trapped in the hydrate particles and operating gas velocities. Owing to the design and operational principles of the GSC it is possible to reduce particle breakdown to at least the same as what is found in long rotary kilns. Other major advantages reviewed are obtained through simplifications in plant design and operation, pointing to low specific power and heat consumption, and generally low production costs, thereby providing an attractive alternative to fluid-bed calciners.

Jan 1, 1981

By D Craw

A glasshouse experiment was set up to investigate arsenic uptake in rye corn grown in different arsenic rich substrates. Sods of material were taken from various locations and planted with rye corn seeds. The plants grew for 13 weeks after which time the above ground biomass was harvested. Analysis of the rye corn plants showed a narrow range of arsenic concentrations, which did not reflect the arsenic contents of the soil. Comparison of the results from this study with previous work showed the glasshouse rye corn to have lower arsenic concentrations in above ground biomass than rye corn grown in field conditions. The environmental conditions present on the tailings and water-rock interactions were considered the main factors involved with the difference in arsenic uptake between field studies and the glasshouse study. This suggests that bioavailability processes are influenced by a variety of factors and cannot necessarily be predicted by the use of soil factors or glasshouse trials alone as is often done when planning phytoremediation work and mine shut down.

Jan 1, 2007

By Morland R

In the course of an exploration program aimed at increasing Pasminco Mining's ore reserves, an electromagnetic survey down one of the underground drillholes at the North Mine, Broken Hill, recorded a broad and persistent response. This paper demonstrates that the anomaly was not due to any geological feature, but rather was caused by 'self-response' of the sensing probe. The observed results are due to the surveyed hole lying within a resistive environment and having distinct, but not unusual, changes in dip.This phenomenon has not been widely reported and we believe that there are likely to be similar cases in company records where very genuine looking responses are due to self-response rather than sulphides. These false anomalies can be recognised by correlating the observed data with the calculated down-hole component of the transmitting loop's primary field.

Jan 1, 1994

The Ramu chromite deposit occurs in the Marum Ophiolite complex and is the most economically attractive chrom-ite deposit in Papua New Guinea. Its lateritic nickel, chromite and cobalt potential has attracted several compan-ies to prospect the deposit.In the present work, the compositions of chromite in the Ramu lateritic deposit and coexisting olivine-chromite pairs in Marum Ophiolite dunite were analysed with the electron microprobe for Fe, Mg, Cr and Al. The results were used to determine the relationship between the cations in the tetrahedral and octahedral structures of the chromite. In addition, the Fe, Mg, Cr and Al cations of the coexisting olivine-chromite pairs were used to calculate the equilibrated temperatures of crystallisation of the chromite. The variation of Fe", Mg and Cr cation values of the chromite in relation to the calculated temperatures was studied by regression analysis.

Jan 1, 1994

Mining education in Ballarat has a long and proud history dating back to the 1870s. Today the School of Engineering continues this tradition at the University of Ballarat. The recent review of Tertiary Minerals Education by the Minerals Council of Australia has questioned the current situation regarding Minerals tertiary education in Australia and recommendations have been made regarding the future of minerals tertiary education. This paper initially examines the original recommendations made by the Minerals Council of Australia and assesses subsequent changes made to these recommendations. Secondly the paper outlines the future shape of mining education in the light of these recommendations given that they are implemented. Finally the future delivery of mining education is discussed, particularly with respect to the impact of modern technologies.

Jan 1, 2004

As mining and extraction processes improve and lower grade ores become economic, mining for most ores have extended to depths beneath the zone of weathering oxidation created over geological history. These deeper openings expose sulphidic formations and reduced mineral species as either primary ore or simply as accessory or gangue minerals in the country rock. This is not new, underground mining for primary base metal and gold have long been familiar with these problems, as have coal and uranium miners. The change is simply that the number of mines exposing sulphidic waste rocks, tailings to the atmosphere and/or leaving behind dewatered sulphidic rock surrounding the mine void has increased the number of sites from where acid mine drainage (AMD) may emanate with consequential problems for the hydrological environment including downstream catchments (Miller et al, 1996). The principles of ecologically sustainable development (Brundtland, 1987) have been more or less ratified by all the developed nations of the world and this has led, amongst other things, to an expansion unprecedented in the research and documentation of means for achieving long-term environmentally acceptable stabilisation of solid wastes of all sorts. These have revealed that AMD problems can be minimised and even reversed in many cases by the integration or co-disposal of biodegradable organic wastes with oxidising sulphidic wastes (Elliott et al, 1996). This paper considers how this might be achieved at mine sites in Australia and the results encountered at some relevant sites.

Jan 1, 1997

By K H. Esbensen

Sampling of grain, animal feeds (solid and liquid) including important mineral mixtures in the Danish agricultural sector is subject to an ongoing investigation with the objective of improving existing (suboptimal) sampling procedures. Results from the first six months are presented here; the project will continue for two more years and will include international collaborators (Australia and Canada). The Danish authorities have instituted a system of control analysis, which contains a set of mandated sampling and analysis methods. From a preliminary survey it was concluded that in fact all of the existing sampling procedures are not optimised in the light of Pierre GyÆs Theory of Sampling (TOS).

Jan 1, 2005