Search Documents

By Ryan A, Dennis R, Dekker D, Ellis W, Sowerby B

An automated facility for non-destructive elemental analysis of mine samples has been developed and tested at Mount Isa in association with the CSIRO. The analysis is based on the prompt and delayed measurement of gamma radiation emitted by the sample during and after separate fast and thermal neutron irradiation. No sub-sampling or sample preparation is required and the analyser is operated by one person that would otherwise be splitting drill core in preparation for conventional analysis. The analyser has been calibrated to measure the following (precision in parenthesis): Ag (14 ppm), Pb (0.5 wt%), Zn (0.5 wt%), Cu (0.04 wt%), Fe (0.7 wt%), S (1.1 wt%), SiO2 (0.8 wt%), A1203 (0.07 wt%), Mn (0.05 wt%), specific gravity (0.02 g cmt). Crushed or whole drill core samples that range in size between 0.5 m and 1.8 m of equivalent BQ size drill core can be analysed at a rate of six samples per hour. If required, drill core samples can be re-packed in their original configuration for storage following analysis. Standard samples are measured every day to ensure operational stability. The analyser is controlled by a personal computer which prints the results and stores them along with the raw data on the computer hard disk. This paper reports the performance of the analyser during 1992 for routine analysis of drill core from the lead ore bodies of both Mount Isa and Hilton mines.

Jan 1, 1993

By R Herbert, M E. Malmstr÷, S U. Salmon

The study focuses on sulfide oxidation processes in unweathered pyrite-rich mine tailings from a soil-covered impoundment in northern Sweden. To simulate the oxygen-limited conditions in water saturated tailings two long-term column experiments were performed. Results are presented for the first 11 months of the experiments at room temperature. The tailings used in the experiments were of two different grain sizes (one coarse grained, in the range 0.02 - 0.6 mm with a grain surface area of 1.86 m2 g-1, and one fine-grained, in the range 0.0015 - 0.06 mm with a grain surface area of 10.00 m2 g-1) and with slightly different mineralogical composition. The S:Fe molar ratio in the leachates (1.0 - 1.5) indicates either that pyrrhotite is the main iron sulfide undergoing oxidation in our experiments, or, alternatively that the S:Fe molar ratio in the leachate is determined by pyrite weathering in conjunction with other processes releasing iron or immobilising sulfate. However, speciation modelling of the leachates indicates that ferrihydrite was close to saturation, suggesting that a ferric oxyhydroxide may have dissolved/ precipitated during the experimental period, thereby affecting the S:Fe molar ratio. Pyrite oxidation rates obtained from the two column experiments during æsteady-stateÆ were 2.25 + 10-13 and 8.45 + 10-14 mol m-2 s-1 in the coarse and fine tailings, respectively. Pyrrhotite oxidation rates, as an alternative, were 2.31 + 10-12 and 1.24 + 10-11 mol m-2 s-1 in the coarse and fine tailings, respectively. Natural microbial activity was confirmed in both the tailings and the leachates; therefore, the obtained oxidation rates are not strictly abiotic. It is thus concluded, based on the experimental results, that tailing heterogeneity will result in zones with different oxidation rates, related to their physical and chemical properties.

Jan 1, 2003

By P G. Fuller

The Woodlawn Mine near Canberra faced the challenge of poor ground conditions from the commencement of underground operations 1987. Talcose shears bounded the dense massive sulphides on both the hangingwall and footwall side of the orebody. In another area the talc existed not only on the edges of the orebody but through out it as well. The country rock was relatively weak shales compounded by a low stress environment that allowed the wall rocks to fall apart quite easily. The challenge for the operators was to overcome the poor ground conditions. This was done by attacking the problem from three directions:technology, how technology is applied, human relations and leadership by all levels of the Management team, and by ensuring that these processes meshed together well.Woodlawn in it early days as an underground mine enlisted the assistance of BFP (Formerly Barrett Fuller and Partners) as a second set of eyes to assist with the assessment of the ground control procedures. The results are discussed in this paper. The progression to this end result included:non-contract payment systems; ground control training for the full range of mining personnel; the development and enhancement of cable bolting and shotcreting equipment; the development of Practical Standard Work Procedures by mine operators; and innovative use of shotcrete and cables bolts to control extremely poor ground conditions.

Jan 1, 1998

By J Chan, T Baumgartl, A Plante, C Peltre, P D. Erskine

Mine soils are often organic matter and carbon poor due to disturbance, topsoil stockpiling and mixing with spoil. They present an opportunity to observe the accumulation of soil carbon arising from rehabilitation or ‘green carbon’ through organic matter inputs and may be considered for carbon credits. Soil carbon is known to improve multiple soil characteristics and is viewed as an indicator of soil health.When attempting to estimate soil carbon levels in the Australian coal mining regions, both coal and black carbon (BC) need to be quantified. Coalmine soils contain coal particles that are difficult to distinguish from organic matter using standard carbon analyses. BC, a material arising from the incomplete combustion of organic matter and fossil fuels, displays some similar characteristics to coal and is ubiquitous in Australian soils due to bushfires. The presence of coal and BC complicate the determination of green carbon levels in mine soils.A method to quantify coal and BC in mine soils from the Bowen Basin using thermal analysis and multivariate curve resolution is presented. By determining BC and coal contributions it is then possible to calculate green carbon levels in rehabilitated mine soils. Calculated green carbon levels are compared with bulk density as soil quality indicators.CITATION:Chan, J, Baumgartl, T, Erskine, P D, Peltre, C and Plante, A, 2014. Distinguishing carbon fractions in coalmine rehabilitated soils, in Proceedings Life-of-Mine 2014 , pp 491–498 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By García B., Wolff E.

The pellet qualities primarily depend upon the thermal profile and gaseous environment during induration. During the induration of the pellet, it undergoes physical as well as chemical changes. Physical changes are mostly due to sintering and chemical changes are due to carbon burning inside the pellet. The effect of carbon on sintering is investigated on a single pellet scale using an optical dilatometer. Sintering is a complex process that involves transportation through various mechanisms. Sintering is quantified in terms of sintering ratio and the kinetic parameter, exponent ‘n’, under isothermal conditions is deduced using the power law equation. The value of n can be used to estimate the sintering mechanism at different isothermal temperatures. Also, the activation energy is calculated using the empirical Arrhenius equation. The activation energy of 0 per cent coke and 1 per cent coke-containing pellets are 531.0 kJ/mole and 552.6 kJ/mole respectively. The order of magnitude of activation energy suggests the same mechanism in both cases. Although the mechanism of sintering is the same, 1 per cent coke-containing pellet sinters more at any isothermal temperature.

Jun 17, 2024

By M I. Pownceby, S Hapugoda, H Han, E Donskoi, L Lu

Iron ore sinter mineralogy and its associated macro-/micro – structure has a strong impact on sinter quality. At a macroscopic scale, sinter ideally consists of a strong, porous matrix which bonds relict ore nuclei together. Microscopically, the sinter matrix (solidified from the melt part of the initial sinter mix) generally consists of complex calcium ferrites known as SFCA, secondary magnetite and hematite grains (precipitated from the primary sinter melt), glass and silicates. Depending on the conditions under which the sinter structure is formed, two major forms of SFCA with different morphologies are generally recognised, ie fine micro-platy SFCA (usually termed SFCA-I) and coarse columnar/prismatic SFCA. Detailed optical microscope observations of several pot grate and compact sinter samples revealed the presence of a variety of fine, coarse and dense forms of both types of SFCA. The controlled cooling tests revealed that cooling rate has an impact on the form and size of SFCA crystals. In this work, EPMA analysis of SFCA compositions from a variety of pot grate and compact sinter samples are presented. Results show that the SFCA types exhibit a broad range of complex compositions within the system Fe2O3/CaO/SiO2/Al2O3/MgO/TiO2/MnO2. Although SFCA-I and SFCA are known to be crystallographically distinct and with different, well-defined ranges in composition, there was considerable overlap in compositions of the experimental sinter samples. The development of SFCA textures depend on several parameters including the local chemistry and conditions including the maximum temperature attained and the cooling rate, within the sinter bed, thereby suggesting that SFCA identification based on morphology alone may be erroneous.

Nov 8, 2021

By A Woodley, A N. Danoucaras

In 2012 the Bureau of Meteorology, under the banner of the Water Accounting Standards Board, released the Australian Water Accounting Standard 1 (AWAS 1). This standard has been in development since 2007 with key milestones being the release of the Preliminary Australian Water Accounting Standard in 2009 and the exposure draft of the Australian Water Accounting Standard in 2010. Throughout this period, the Minerals Council of AustraliaÆs Water Accounting Framework has developed concurrently with the Australian standards and the standards have informed elements of the framework. However, the framework is not identical to the standard as the objectives between the two are different. The objective of the Water Accounting Framework is to create consistency in water reporting of the minerals industry and to assist companies reporting to corporate sustainability initiatives. The objective of AWAS 1 is to provide information to water management bodies to facilitate decisions about the allocation of water resources. Companies are to report on an annual basis - not only physical flows of water but contractual requirements to supply and obtain water - regardless of whether the transaction has been fulfilled in the reporting period. In contrast, the Water Accounting Framework only reports on flows that have physically happened. The paper will provide summary information on aspects of AWAS 1 that are most relevant to the minerals industry, show the alignment and differences between AWAS 1 and the Water Accounting Framework and explain how to obtain the information for the AWAS 1 reporting statements.CITATION:Danoucaras, A N and Woodley, A, 2013. Alignment and differences between the Australian Water Accounting Standard and the Water Accounting Framework for the minerals industry, in Proceedings Water in Mining 2013 , pp 85-90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

Australia is a highly significant hub in the global minerals business. This paper will present the results of global and national studies looking at the potential 20 to 30 year future evolution of the mining and metals industry.   Globally, the World Economic Forum launched a Mining and Metals Scenarios project in January 2009 to explore the question: 'How will the environment for the global mining and metals industry look in 2030?'. As part of a structured strategic foresight process, eight workshops were held across the world over the course of a year which brought together over 200 leaders from the private sector, government, academia and non-governmental organisations. The workshops were supplemented by personal interviews and guided by an international advisory board.   Critical uncertainties for the future of the industry were identified and compare extremely well with the outcomes of a national survey of AusIMM members identifying the key issues and drivers shaping the future of their operations. Global context was one of the most significant issues identified by The AusIMM membership, which is expanded in the World Economic Forum study in terms of: geopolitics; global governance; action on climate change; and economic outlook. More specifically, this global study developed three divergent yet plausible scenarios describing potential environments for the global metals and mining industry in 2030. These scenarios are compared with ground-breaking global foresight work coordinated by the Stockholm Environment Institute in the 1990s. The scenarios will help decision makers rehearse alternative futures, anticipate potential hazards and identify business opportunities - new solutions, new markets and new connections. The presentation will present these scenarios as a way of challenging thinking, testing established wisdom, and stimulating imagination about the business case for the mine of the future. As Marcel Proust put it, 'The real voyage of discovery consists not in seeking new landscapes but in having new eyes'. This is an ABSTRACT ONLY no paper was prepared for this presentation.

Jun 1, 2010

By G M. Mudd

Mine tailings represent one of the two largest sources of mine waste from the minerals industries (the other being waste rock). Given the problems of declining ore grades and growing production, tailings generation is increasing exponentially across the global mining industry. Common practice is for mines to build large containment dams to store tailings during operations, which are then rehabilitated following mine closure. At some sites, however, the controversial practices of riverine or marine dumping of tailings is still practiced. As recent tailings dam failures have shown, there are legitimate questions being raised about the long-term viability of leaving tailings above ground due to the risks of collapse and failure. At present, it is rare for mines to emplace tailings back into former mine voids following mine closure, most commonly into a former open pit mine void (although a fraction of the tailings may be used for underground mine backfill, this is minor in scale). The approach of in-pit tailings has numerous advantages, such as inherent physical stability, low to negligible acid and metalliferous drainage (AMD) risks, as well as allowing more productive use of formerly mined land. In tropical areas where surface repositories are prone to leakage with potential for AMD and widespread dispersal of radionuclides (in the case of uranium mining), in-pit management provides particularly strong advantages – thorough hydrogeological studies are required, however, to address residual groundwater contamination risks and to establish sound, long-term environmental monitoring regimes for groundwater quality and subsidence issues. This paper presents a study of in-pit tailings management and compares it with surface repositories established in a tropical climate. The comparisons lead to the conclusion that, at least under tropical conditions, in-pit tailings management should be considered as world’s best practice – especially for radioactive uranium tailings.

Aug 8, 2011

Synthetic and commercial activated carbons are characterised for several chemical and physical properties. A range of techniques is used to establish correlations between physicochemical parameters and gold- adsorption activities. The most important parameter in the carbon activation process for a product with a high gold-adsorption activity is the activation temperature. High activation temperatures yield products with large micropore volumes which provides sites that are ideal in size for adsorption. The surface area of an activated carbon is not necessarily a good measure of its adsorption activity. Surface oxygen-containing functional groups are identified by Fourier transform infrared spectrophotometry to be comprised mainly of ethers and hydroxyls. These functional groups line the edges of the micropores imparting a polar character to the pore and aid in the solvation of the adsorbate. Oxidants such as nitric acid result in a proliferation of surface carboxyl groups. resulting in a negatively- charged surface that is not conducive to the adsorption of gold.

Jan 1, 1993

By Manca PP, Lassandro R, Caranassios A, Massacci G, Ciccu R

The paper discusses the state of the progress reached in the development of the diamond wire tool for cutting hard rocks. To the advances of this relatively new technology a substantial contribution has been provided by the research being carried out at the University of Cagliari on samples of granite rocks from different Sardinian stone quarries. On the basis of field experiments and laboratory test data, the mechanism of diamond wire cutting has been assessed. In particular the influence of the rock features and operational variables on tool performance (cutting rate and bead wear) has been Elucidated.

Jan 1, 1992

By R N. Lamb, A N. Buckley

Experiments have been carried out to establish whether time-of-flight secondary ion mass spectrometry (ToF-SIMS) is able to differentiate monolayer and multilayer coverage of thiol collectors on sulfide minerals. The systems investigated were those for which x-ray photoelectron spectroscopy is able to provide an independent determination of the extent of coverage, and included diethyldithiophosphate (DTP) and 2-mercaptobenzothiazole (MBT) on chalcocite, DTP on Ag2+MS prepared by sulfidising metallic silver, and isobutyl xanthate (BX) and MBT on galena. For monolayer adsorption of MBT on chalcocite, peaks from MBTû but not Cu(MBT)û ions were evident. For multilayer coverage, Cu(MBT)2û ions were clearly present, notwithstanding the fact that other data had identified the principal multilayer species as Cu(MBT). For adsorbed DTP on copper and silver sulfides, DTPû and metal(DTP)Hû peaks were observed for monolayer and multilayer coverage. Although the multilayer species was expected to be predominantly metal(DTP), metal(DTP)2û ions were evident for multilayer (but not monolayer) coverage. For the PbS/BX system, intact Pb(BX)2 or Pb(OH)BX ions were not detected for multilayer coverage, although Pb-containing ions heavier than PbBX were. Indeed, for all the systems studied, ToF-SIMS was able to differentiate monolayer from multilayer coverage. In general, however, the SIMS evidence alone might not be sufficiently definitive to effect the differentiation. In the case of collector adsorption on copper and silver sulfides, if the multilayer species detected had been the metal monothiolate only, and had not involved the formation of some metal dithiolate, then ToF-SIMS might not have been able to provide an unequivocal differentiation of the two coverage conditions.

Jan 1, 2005

By Wakamatsu DT, Nakahiro Y

This present paper deals with the fundamental study of the separation of fine cassiterite and quartz by liquid-liquid extraction using iso-octane as an oil phase, dodecylamine acetate (DAA) as a collector, and sodium chloride as a depressant. With regard to the distribution of fine cassiterite and quartz between oil and aqueous phases, the effect of DAA has been investigated in terms of pH, DAA and NaCl concentrations, zeta potential, and adsorption density. From the results of the experimental work, a maximum recovery of cassiterite in the oil phase was obtained with pH around 6.0, DAA concentration of 1.0 x 10-5 mole/litre, and NaCl addition of 0.1 mole/litre. In these conditions of liquid-liquid extraction, most of the fine quartz remained in the aqueous phase. Thus it was found that NaCI was an effective depressant for fine quartz under optimum conditions. A series of separation tests by liquid-liquid extraction was then conducted for the mixed samples (6.0 per cent Sn) of cassiterite and quartz. By a single separating process, the per cent of recovery of cassiterite in the oil phase was about 92 per cent with a grade of 27 per cent Sn. The same results could also be obtained by using kerosene in place of iso-octane as the oil phase.

Jan 1, 1993

Design and construction techniques used to develop two highway tunnels in inaccessible mountainous terrain are described. Measures used to adapt the design to the unusual geology and topography are discussed, as well as measures to adapt the construction methods to available equipment, materials, and skills. Sharp local variations in geoloqic conditions resulted in field modifications to both design and construction techniques. The geology is a volcanic ash and breccia-agglomerate at one site, a jointed andesite at the other, which is also the site of a major landslide. Both rock reinforcement in the form of pretensioned and grouted rock bolts with a shotcrete lining,and rock support by struc- tural steel sets with a reinforced concrete lining were used. A canyonside location and high lateral in-situ stresses required modification of design procedures. Pilot tunnels at both sites resulted in adapting the designs to site conditions with large savings in lining costs, disclosing problem areas in advance of the main excavation, and cushioning of blasting pressure to minimize stability problems.

Jan 1, 1976

By Gill L. F, Gleeson HB

This paper describes the development of a Computer Aided Design and Drafting based mine planning system in the State Electricity Com- mission of Victoria. The system combines a commercially available CADD system with a commercially available mining/geological package. The methodology used in the establishment of the combined system, the fea- tures of the system and the current status of development are discussed.

Jan 1, 1989

By S N CARRAS

Ore reserve estimation is a procedure involving data collection, data storage and judgement and assumptions about geology mining and metallurgy. Calculations are based on these assumptions and an economic analysis on projected cash flows is carried out. Ore reserve estimation must therefore be subjective and will always depend on the extent to which the assumptions used in arriving at the estimate are correct. This paper is an attempt to summarise the many aspects that can contribute to ore reserve problems and to offer some suggestions on how to minimise these problems. For further details on specific concepts readers are referred to the detailed descriptions in the referenced papers.

Jan 1, 1992

Since the earliest recorded prospecting of the 1860's mineral exploration and mining in Fiordland has been discouraged by the formidable physical difficulties presented by its isolation, extremely rugged relief, treacherous coastal waters and generally unfavourable weather conditions. Government assistance was often sought by the miners and prospectors but little, if any, support or encouragement was received after the initial period. During the 1840's decorative marble was quarried at Caswell and Dusky Sounds. A prospector discovered and attempted to mine copper sulphides to the north of Dusky Sound (Parks Mineral Beds) and near Mt Solitary. A small Pb, Zn, Cu, Ag, Au bearing quartz reef was discovered and driven on in the granite coast line of Preservation Inlet (Bradshaws Reef) and the ore roasted on site. Alluvial and quartz lode gold was discovered at Preservation Inlet in the 1890's and led to the recorded recovery of 11 000 oz of mainly lode gold. Falloff in grades with depth, thinning and splitting of the reefs and the high mining costs at this location led to a virtual abandonment of the field by 1906. In the late 1950's and early 1960's the geology of Fiordland was mapped by the Geological Survey at 1:250 000 scale, but field work was largely confined to the shore lines of the coast and fiords. In view of the physical difficulties it is not surprising that mineral exploration and mining up to 1970 was limited to the scant attention outlined above.

Jan 1, 1977

By Z W. Orndorff

Excavation through sulfidic geologic materials during construction activities has resulted in acid rock drainage (ARD) related problems at numerous (>40) locations across all five geologic regions of Virginia, USA. Potential acidities ranging from >100 to develop a statewide sulfidic materials risk map; document ARD impacts to soil and water quality and engineered structures; and develop methods to assess site-specific risk potentials within a given highway corridor. A statewide sulfidic materials GIS risk map was developed based upon the state digital geology map which assigned four levels of relative risk to all mapped strata based upon predicted lime requirements and probabilities of encountering highly reactive materials. Non-highway construction activities have also routinely disturbed sulfidic materials, and a recent airport project in northern Virginia resulted in over 150 ha of extremely acidic (pH 45 mg/L) run-off from this site heavily damaged a receiving stream, partially due to the fact that it dissolved the galvanised steel water control structures in stormwater detention basins, leading to direct discharge of run-off and sulfidic sediments. The airport area was treated and revegetated in 2002 with a combination of lime-stabilised biosolids, straw mulch, and acid-tolerant grasses. Water quality in a receiving second-order stream quickly responded to the treatment, but some release of N was also noted as a secondary effect. Collectively, these results point out the importance of accurately assessing the potential for excavation of sulfidic materials in construction environments, and the necessity of developing toxic materials handling strategies similar to those employed in mining environments.

Jan 1, 2003

During the past three years Lurgi's Circulating Fluid Bed (CFB) technology has been successfully applied to roasting of refractory gold ores and con- centrates. In comparison with the so-called Stationary Fluid Bed roasting systems, a considerable improvement of gold recovery, to around 95 per cent, has been demonstrated and achieved on many occasions in pilot CFB units and in commercial CFB roasting plants as well. The major reason for such improved gold recoveries is the excellent controllability of the roasting process in the CFB reactor system. Here, temperature, gas atmosphere and solids residence time are more precisely controllable at optimal values during roasting operation in order to achieve the highest possible gold recovery in the subsequent leaching process step. Further dominant benefits of CFB roasting systems are their flexibility with regard to feed material, throughput capacity, dry or slurry feed, almost unlimited oxygen enrichment, direct fuel addition and in situ capture of SO2 in the presence of limestone and dolomite. The system will accept 50 per cent turndown ratio, large variations in feed composition and particle size, as well as a variety of different fuel types. The commercial applications of CFB roasting systems for gold con- centrates have been realized so far at Fimiston, Kalgoorlie/Westem Australia and for whole ores at Cortez, Nevada/USA.

Jan 1, 1991

By Huleatt M, Perkin D, McLeod I, Mock C, Pratt R, Gourlay A, Timoney E, Knight N, Ward J

Generally speaking, Australia's reserves of its more important minerals (in terms of export earnings) are adequate to sustain forecast rates of production to the year 2000. The rate of forecast production increases of these commodities (aluminium - whether as bauxite, alumina or metal, black coal, iron ore and ferro-alloy minerals, base metals, tin, uranium, and mineral sands) reflects a well- ordered and sustained growth phase of Australia's mineral industry.

Jan 1, 1981