Search Documents

By Harrison AT, Smart RM

Backfill systems using unconventional cementitious hinders have been successfully used in relatively deep and hard rock tabular mines for longwall, scattered stoping and shaft pillar removals. Two unconventional cementitious systems are discussed: 1. A ground granulated blast furnace slag (GGBS) with an activator containing lime. This has been used with a total tailings 'stable' slurry at a relatively low dosage of less than seven per cent, by mass, based on dry solids. The room and pillar stopes supported with this fill were up to 20 in high and the tailings were relatively high in pyrite. .\ GGBS binder plus a silicate based activator and gelling agent that virtually eliminated all water drainage (and hence post filling shnnkage). The system used a slurry, but the addition of the ;iutivator created a final placed product that had the behaviour of a paste. The system has been successfully used for almost ten years in the following applications: ò sloping widths (mining heights) above 1.6 in; and ò shaft pillar removals in seismically active areas at the end of the life of the shafts. \This paper discusses the technical merits and costs of the systems and compares them to other fill systems (including true paste systems).

Jan 1, 1998

By D Caffrey

To demonstrate the advantages of using electronic delay detonators over pyrotechnic detonators, a trial using the DNES Dynatronic System was conducted at the KCGM Mount Charlotte operation in 1998. The trial clearly demonstrated that accurate control over the firing delay time between blastholes can lead to fragmentation improvement and ground vibration energy control which are two important issues for the Mt Charlotte underground operation. Excellent fragmentation was achieved by employing a 12 ms delay sequence. Detailed fragmentation analysis has shown a 10 to 20 per cent passing increase for the rock fragment size from 0.1 to 0.4 m compared with the pyrotechnic detonator firing. There was no increase in ground vibration level on the surface with the electronic detonator firing even though the electronic detonator firing had a much shorter blast duration than the pyrotechnic detonator firing. In fact, our energy calculation has clearly shown that much less energy had been propagated to the surface from the blast using electronic detonator firing.

Jan 1, 1999

By Bidwell TJ, Servant S

Paste back-fill technology is gaining rapid acceptance in the Canadian mining industry. The authors were able to work on four different mining sites employing paste technology in their operation. In each site the paste hackfll is prepared with very fine tailings containing significant amounts of sulphur minerals. The research program involved laboratory testing on samples prepared in the laboratory, on control samples obtained at the hackfilll plant during pouring into the stopes and on core samples obtained from drilling in backfilled stopes. The laboratory testing provided detailed knowledge of the mechanical behavior of the paste backfill. The need for a means of measuring the in-situ mechanical properties of the backfill became clear. A review of various trials published in literature and an evaluation of available technology suggested the Cambridge Self-boring Pressuremeter. A first field campaign confirmed the efficiency and dependability of this instrument leading to the conclusion that it offers a very good method for the in-situ measurement of paste backfill properties.

Jan 1, 1998

By C MacRae, N Wilson

CSIRO Minerals has recently developed an electron microprobe (EMP) based imaging (or mapping) method for characterising ilmenite concentrates. The method requires an electron microprobe analyser to collect elemental X-ray maps which are then processed via an in-house developed software module (CHIMAGE). The type of information readily available from EMP mapping includes; primary phase identification, modal analysis of phases, chemical analysis of individual phases, textural information (eg the alteration stages in the formation of leucoxene or pseudorutile from primary ilmenite and the development of macro-porosity), and the identification of coatings or pore-fill material. All of these parameters will impact on the choice of future downstream processing options considered for any particular ilmenite concentrate. The method has been demonstrated to be a sensitive analytical tool for assessing the distribution of aluminosilicate minor impurities in ilmenite feedstocks from the West Coast of Australia and also for characterising the complex chrome-spinel gangue phases common in East Coast ilmenite concentrates from the Murray Basin.

Jan 1, 2001

By J Miedecke

A metalliferous mine has operated at Storys Creek from the 1890s to 1979. Storys Creek drains from a pristine catchment and National Park and remains as the most degraded stream from historic mining in north-eastern Tasmania. It has been the subject of public concern since the closure, particularly at times of high rainfall such as existed in 1985 and 1986. The mine is located on the banks of the creek, which flows into a major river, the South Esk River, which is one of TasmaniaÆs largest rivers and important for recreational fishing and water supplies. For much of the life of the of the operations tailings were directly discharged into the creek, and in latter years stockpiled or very close to it. Little rehabilitation was carried out at mine closure. The result was erosion and subsequent deposition on the banks of the creek downstream. Direct emissions of adit water and the consequential emission of contaminated ground water to the creek continue to affect water quality. Contaminant loads discharging from the mine and tailings comprise 70% of the metal load in the catchment and are by far the largest single source. Acidity data suggested that the introduction of systems to introduce alkalinity could be effective in ameliorating the residual acid drainage impacts in the Storys Creek catchment. After a period of investigations and trials which proved their effectiveness, treatments adopted have included the following: relocation of tailings to a constructed and clay capped disposal area and rehabilitation of tailings area; crushed limestone addition to stream flows; crushed limestone addition to creek banks and exposed tailings; sealing of a drainage Adit; and construction of an anoxic drain to generate alkalinity to surface waters draining to old mine workings. These innovative treatments have resulted in a marked improvement in water quality draining from the area. The anoxic drain is believed to be one of the few, if any, which has been constructed to have generated high levels of alkalinity from clean waters and offers a solution to the clogging problems experienced in such drains in the past. Similarly, the use of crushed limestone in an active stream has proved effective in buffering acid drainage and removing metals from solution.

Jan 1, 2003

By Giles D, Wegmann D

The Mt Todd Gold Project is located 42 km northwest of the township of Katherine within the Northern Territory of Australia. It is situated in the southeastern portion of the Pine Creek Geosyncline. The Batman gold deposit, the largest of several deposits at Mt Todd, hosts an identified mineral resource of 92.9 million tonnes (Mt) grading 1.4 grams/tonne (g/t) as at 31 December 1993. Host rocks at Batman are assigned to the Early Proterozoic Burrell Creek Formation, comprising greywacke and siltstone interbedded with shale. Gold mineralisation is associated with a very broad zone of sheeted and stockwork quartz-sulphide veins that occupy a corridor of intense brittle fracture and faulting. A conceptual model of formation involves the dilation of joints and micro-faults within overlying sediments during sinistral movement along a basement shear zone. Synchronous granite intrusion generated convective circulation of crustal fluids through the sedimentary pile resulting in the formation of auriferous quartz veins within favourable structures. The Batman zone of mineralisation is not directly related to fold structures which typify several other major gold deposits within the Pine Creek Geosyncline.

Jan 1, 1994

By B Morey, J Gordon, P Mackenzie

Mount Tom Price Mine is peerless amongst Rio Tinto iron ore resources around the world. It has provided Hamersley Iron with premium quality, high lump yield haematite ore over the last four decades. The Brockman type bedded ore, containing bands of haematite and shale of varying thicknesses has been traditionally bulk mined to either high-grade or low-grade based on alumina cut-off grades. As open pit mining has progressed deeper into the orebody approaching the keels of the megastructure, increased structural complexity, chemical and physical variations in the ore, unfavourable ore presentation and reduced blending options have become an issue for grade control and may have serious impacts on product stockpiles. The grade blocks and boundaries must be accurately defined according to geological contacts and where identified, selective mining may be applied. Therefore in-pit geological mapping is the definite and ultimate guide to achieve target grades and grade predictions. Under this scenario, it is absolutely vital that the mine geology team ensures this geological knowledge is passed onto the related departments including mining crews as well as to the short- and long-term planners.

Jan 1, 2002

By Y K. Leong

Occasionally additives are used in the wet processing of iron ore tailings and slurries, for examples, in the thickening of tailings with flocculant to recover process water, and in the smooth pumping of concentrated slurries. They can mitigate slurry behavioural issues that could significantly affect the plant operation and production. The nature of iron ore business requiring the plant to have a high throughput to be economical, large amounts of slurries are therefore processed every day. The quantity of additives needed will correspondingly be large and so are the associated costs. This could have a significant impact on the plant profitability. If additives are used they must be very costeffective. NaOH is among the lowest cost chemicals available, at ~US$400 per ton. In this paper we will look at use of composite additives involving phosphate compounds with NaOH added to reduce the cost, for the control of iron ore slurries rheology. The NaOH worked synergistically with the phosphate compounds. The effectiveness of these composite additives in viscosity reduction can be neutralised by another cheap additive such as lime or a Ca(II)-based salt turning the slurries back to being a paste. Tailings paste is an ideal material for safe storage in the dam. These composite additives can also be used to facilitate the recovery of iron ore at commercial grade from tailings (Leong, 2020a, 2021a).

Sep 18, 2023

By CorrOa de Araujo A, Salum MJG

The treatment of mining and metallurgical liquid effluents is becoming, everyday, a necessity felt by these industries. Physical-chemical and chemical methods for treating such effluents are generally necessary whenever heavy-metals and other toxic compounds such as cyanide are present. The present paper discusses the use of precipitate flotation as an alternative physical- chemical method that can be applied for the treatment of effluents containing heavy-metals (mainly zinc and cadmium) and cyanide. Examples of laboratorial scale applications on real effluents are given. In both cases precipitate flotation was able to reduce the concentration of toxic components of the effluents at a very high removal rate, generating a solid waste that can either be disposed, re-used or recycled. A cationic collector - dodecylamine hydrochloride - demonstrated to be the best choice of surfactant for the two systems investigated. Sodium sulphide and dithizone were selected for the precipitation of the zinc bearing effluent whereas a copper salt was preferentially used for precipitating cyanide in a form adequate for its recycling envisaging the use of an AVR (acidification - volatilisation - regeneration) technique.

Jan 1, 1993

By K Saito, M Hasegawa

Removing sulfur and phosphorus from molten iron can be expressed by the following reactions, respectively. [S]Fe + (O2-)slag = (S2-)slag + [O]Fe [P]Fe + (3/2) (O2-)slag + (5/2) (FeO)slag = (PO43-)slag + (5/2) Fe(liquid) These equations indicate that desulfurisation and dephosphorisation have opposite oxygen potential conditions. If a small amount of desulfurisation slag not removed is carried over to dephosphorisation process, the reaction of sulfur mentioned above proceeds toward left hand resulting in increasing sulfur content in molten iron. For better understanding of such re-sulfurisation reaction in hot metal pre-treatments, the present study aimed at evaluating the effect of iron oxide on the sulfur distribution ratio between slag and hot metal. To measure sulfide capacities and FeO activities simultaneously at temperatures below the melting point of pure iron, CaO-SiO2-FeO and CaO-Al2O3-FeO ternary molten slags were brought into equilibria with copper-iron-sulfur liquid alloys, and the equilibrium oxygen partial pressures were determined with an electrochemical technique involving the stabilised zirconia solid electrolyte. The experimental results showed that the sulfide capacity increased with an increase in FeO content, and this trend was consistent with the fact that FeO was basic. Although the addition of FeO raised the FeO activity and oxygen potential, the calculated value for sulfur distribution ratio between slag and hot metal increased with increasing FeO content.

Jun 19, 2024

By C Li, K McDonald an, T Nicholson, C Brown

The relative reactivities of chars prepared from different coal samples at temperatures in the range 500 to 1150¦C were determined by measuring the rates of metallisation of a standard ilmenite concentrate. The results have been interpreted in relation to different measured physical and chemical properties of the chars. Char reactivities were found to correlate with the maximum specific surface area (SSA) of the chars, obtained from plots of SSA versus temperature. Weathering of coal samples gave higher reactivities which correlated with higher SSAs. Experiments using recycled chars showed that the high internal SSAs developed during earlier reduction reactions provide no benefit in terms of increased metallisations. The important role of char hydrogen contents in controlling low temperature metallisation rates was demonstrated. Chars prepared from different rank coals had the same hydrogen content when prepared at the same temperature. Ilmenite metallisation rates had a linear dependence on the hydrogen content of the chars. Large differences in the slopes of the metallisation versus H2 content curves for different chars were interpreted in terms of SSA variations and catalysis of the gas reactions by dispersed metallic iron particles in the chars. A simple test based on magnetic separation of the char was shown to give an indication of enhanced reactivity due to contained metallic iron.

Jan 1, 2001

By R Shrimali, P Rajmeny, L Shekhawat, A Joshi

Rampura Agucha open pit mine has successfully been excavated to a depth of 320 m, incorporating multistage working. The key to success is the implementation of presplitting as control blast measures at every stage of mining, including intermediate cut backs, in addition to the final wall. The major challenges encountered in establishing presplitting in the hang wall as compared to the footwall of the mine are:reversely dipping foliation, ie dipping into the hang wall itselfstriking obliquely at an angle of 20–30° with regards to the general strike of the pit wallthe presence of numerous geological planes of weaknesses like major faults, slips, etc.Control blast parameters like hole inclination, spacing and stand-off with buffer row were chosen initially from the literature survey and were subsequently fine-tuned by field trials to the mine geo-mining conditions of the hang wall. Electronic initiation used for trim blasts along with double presplitting in fault-affected zones helped in getting better presplit performance and resultant stability of the hang wall.CITATION:Rajmeny, P, Shrimali, R, Shekhawat, L and Joshi, A, 2015. Establishing the design parameters of a control blast for long-term stability of the hang wall at Rampura Agucha Mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 437–446 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By P Corbett, P Sheffield

Springvale Mine is an underground coal mine in the western coalfield of New South Wales which utilises retreat longwall mining technique. The mine encountered significant gateroad floor heave issues during retreat of LW415. Floor heave has subsequently impeded longwall advance as well as longwall bolt up and recovery to some extent during the extraction of the next five longwalls. Floor heave at Springvale Mine develops throughout the lifecycle of the mine roadways, and is most prevalent in longwall gateroads. Floor heave has been measured as early as 2 weeks after roadway development and continues to develop through the post-development phase, with a rapid increase in close proximity to the longwall face. This paper presents a case study of the evolution of understanding of floor heave behaviour at Springvale Mine based on geotechnical characterisation, an intensive convergence monitoring program (roof and floor movement) and spatial correlation of monitored locations with longwall face position. The analysis considers previously known factors contributing to floor heave including mining depth, geological and physical properties of the rock mass and mine design geometry. Investigation results indicate a strong correlation between floor heave magnitude and roof dilation magnitude, geophysically inferred faulting in underlying strata, areas of localised stress concentration and mine roadway dimensions. This paper also discusses the predictive model which was developed as a result of the study, which is now the basis of the floor heave removal program used to manage roadway convergence at the mine. Floor heave monitoring, prediction and management strategies (including floor reinforcement and removal) are also discussed. CITATION:Sheffield, P and Corbett, P, 2018. Managing floor heave in an underground longwall coal mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 78–94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By C R. Stanley, D Lawie

The measurement of error in assays collected as part of a mineral exploration program or mining operation, including errors introduced during sampling, sample preparation, or geochemical analysis, historically has been undertaken in a variety of ways. Different parameters have been used to describe the magnitude of relative error and each of these parameters is related to the standard measure of relative error, the coefficient of variation. Calculation of the coefficient of variation can be undertaken in a variety of ways; however, only one produces unbiased estimates of measurement error: the root mean square coefficient of variation calculated from the individual coefficients of variation. CITATION:Lawie, D and Stanley, C R, 2012. Average relative error in geochemical determinations - Clarification, calculation and a plea for consistency, in Proceedings Sampling 2012 , pp 181-184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

The past decade hap seen revolutionary advances in com-munications and information-handling techniques which have been stiriulated by "cold war" military requirements and by, current programmes for probing into outer space: The tools used in exploration for petroleum and minerals have been improved significantly as a result of this new space age technology and even greater improvements are on the way.Two areas of technical activity have been particularly fruitful in enhancing the effectiveness of exploration, methods. These are (1) The development of new approaches, based on information theory, for extracting signal from noise more efficiently than before, and (2) The use of high-speed digital computers for storing and processing all kinds of exploration information, not only geophysical but geological as well.In seismic prospecting, use of information theory has led to new techniques such as time-domain filtering, wave-number filtering and correlation methods which have made it possible to obtain usable reflection data from areas which were previously considered NR. Complex playback and other data processing facilities have been developed to apply these approaches.

Jan 1, 1963

By A Mortazavi, M Akhmedya

Mining is recognised as being one of the most dangerous industries in the world due to the difficult working conditions. Working in such hazardous circumstances in an underground mine often results in a variety of accidents. The working conditions at Kazakhstan’s underground mines have deteriorated owing to a lack of a risk-reduction plan and methodology. This paper evaluates different underground mines in Kazakhstan and demonstrates the employed mining method and the observed failure modes. Risk assessment has long been recognised as a valuable technique for preventing accidents. In the underground mining sector, risk assessment tools play an important role in avoiding work-related accidents. However, geotechnical uncertainty is a significant source of severe incidents like stress-induced roof collapse, wedge failure, seismicity etc, which result in human and financial losses. A geotechnical risk assessment performed early in the mine design process might assist justify a different mine design component, such as different support systems for a dangerous location within the mine openings during mining. The goal of this research is to create a damage/failure database aiming at the development of a geomechanical risk assessment methodology. This work identifies a thematic structure linked to risk assessment and management for the examined Kazakhstan mining sector. As part of the developed database, the dominant modes of failure within the Kazakhstan underground mining conditions were investigated. The study will provide opportunities to establish future research objectives for Kazakhstan’s mining industry where there are significant gaps between state-of-the-art research and mining operations in practice.

Nov 29, 2022

By S Azam

Coal is a vital energy source and source of carbon for metallurgical applications, contributing significantly to the world economy. Coal mining and processing involve multiple processes that generate Respirable Coal Mine Dust (RCMD), one of the primary sources of health hazards for coal workers. Since 2000, the rate of Coal Workers’ Pneumoconiosis (CWP) has continually increased in the U.S, with severity of the cases also worsening. Increasing evidence shows that exposure to RCMD in coal workers is a high-risk factor for lung cancer, which causes more deaths than the following three major cancers combined in the US Recent observations show an increased incidenceof CWP or other lung diseases, particularly among young miners in the Appalachian basin. The CWP prevalence in Appalachia is four times higher than the national average. Although various regulations are in place, the resurgence of such disease among coalminers demands additional efforts to better understand all the possible facets of coal dust toxicity, taking insights from current interdisciplinaryresearch efforts. One such important field is the interaction of coal dust with moisture in underground mines. Although moisture is prevalent and dynamic in an underground mining environment, it has never been evaluated for its impact on modifying the toxicity of coal dust and transport or flow behaviour. However, research conducted in atmospheric sciences in the past decade makes it clear that moisture in the atmosphere can significantly alter the behaviour of mineral dust. This paper is a part of research aimed at understanding how moisture interacts and alters the characteristics of coal dust. Such insight is crucial in understanding the potential toxicity of coal dust and developing mitigation technologies.

Oct 12, 2022

By C A. Foss, K Blay, K Leslie, D Hillan

Magnetic field studies provide remote sensing of magnetisation distributions and a means to investigate moderately- to strongly-magnetised ore deposits that may be partially or totally buried. However, above-surface magnetic field surveys have limited capability to resolve the detail of magnetisation distributions because of the large separation between the magnetisation and the magnetic sensor. While some of this detail is available from magnetic susceptibility logging within boreholes or from magnetisation studies on recovered core, these measurements are limited to the exact trace of the boreholes. The large disconnect between ground or aeromagnetic surveys and highly-localised borehole sampling can cause problems in developing robust source models from magnetic survey data. The measurement of magnetic field in boreholes has the capacity to at least partially bridge that gap by measuring the magnetic field due to magnetisations proximal to, but not intersected by, the boreholes.CSIRO has developed the world’s first downhole magnetic tensor gradiometer. This instrument measures magnetic field gradients in all directions within a borehole. A prototype instrument has been built and tested as part of phase 1 of the Deep Exploration Technologies Cooperative Research Centre (DET CRC). The prototype performed well with magnetic pyrrhotite at the DET CRC test site in the Adelaide Hills and at Carpentaria’s Hawsons magnetite deposit south of Broken Hill. Further work is required to reduce the diameter of the probe so that it can operate in NQ holes (it is currently limited to HQ or wider) and to transform it to a continuous logging tool. The borehole tensor gradiometer can be used to investigate the continuity of magnetisation over a distance of several metres to tens of metres away from a borehole intersection and the structural dip of the magnetic body. It can be used to either replace or augment downhole magnetic susceptibility logging. This instrument is one component of an integrated CSIRO suite of new magnetic field utilities and methodologies for iron ore exploration and development.CITATION:Leslie, K, Foss, C A, Hillan, D and Blay, K, 2015. A downhole magnetic tensor gradiometer for developing robust magnetisation models from magnetic anomalies, in Proceedings Iron Ore 2015, pp 299–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

The Elgas Underground Storage Facility at Port Botany, Sydney, is the first purpose-built cavern of its kind in Australia and allows large capacity, safe and environmentally benign storage of Liquefied Petroleum Gas (LPG). The facility provides Elgas with the flexibility to source product at competitive prices and will ensure long-term security of supply. Construction has provided Orica Australia, formerly ICI Explosives, with a unique opportunity to provide a bulk explosive delivery system specifically designed to meet the exacting demands of the site (see Figure 1) and of the project.

Jan 1, 1999

By P Revell, G Wilkie, P Walters, L Keeney, F Faramarzi

Grade Engineering® is a value-driven strategy aiming to maximise benefits by exploiting intrinsic grade variability of ore deposits. It utilises a multitude of separation techniques to remove low grade material before being introduced to post-blast size reduction processes, i.e. crushing and grinding. At an operational scale, Grade Engineering® techniques can be implemented at the drill-and-blast stage, to control the degree of fragmentation in accordance with the spatial distribution of valuable minerals across an ore domain through differential blasting. It can also exploit intrinsic textural and breakage characteristics of a given ore type to reject uneconomical barren material at coarse sizes, which is known as Natural Deportment. Grade Engineering® can also be employed in the deliver stage of the mining value chain through sensor-based bulk and particle sorting. Each strategy is therefore highly dependent on the responsiveness of an orebody to available techniques. That is, the extent to which Grade Engineering® drivers would be capable of unlocking potential values of currently un-amenable orebodies depends on how detailed the heterogeneous nature of ore domains can be described. This paper considers exploring possible linkages between deportment characteristics of an ore and its competence when broken in a range of energy inputs at a particlebased level. Accordingly, potential opportunity may lie in exploring whether the intensity of input energy (or degree of fineness) can be used as a lever to improve or ‘unlock’ ore amenability to Grade Engineering® techniques. Implications from such a detailed approach offers new opportunities to enhance Grade Engineering® gains through engineering ore competence variability.

Nov 10, 2020