Search Documents

By S Prakash, P S. R Reddy, S K. Biswal, V N

The beneficiation potentials of two Indian iron ore slime samples by flotation technique using both cationic and anionic collectors are investigated. The direct and reverse flotation of slimes using oleic acid and dodecylamine as the collector have been studied using both conventional cell and flotation column to upgrade the iron content. The characterisation studies of iron ore slimes indicated that the samples are extremely fine in nature and contain substantial amounts of martite, magnetite, goethite, limonite, kaolinite and quartz beside hematite as the dominant iron mineral phase. The samples on average contain around 52 - 58 per cent Fe, four to seven per cent SiO2 and five to six per cent Al2O3. Taking into account the physico-chemical properties of the slimes, it is attributed that both the samples need to be deslimed by hydrocyclone before flotation. The results of both cell and column studies on sample I showed that a feed containing 57.5 per cent Fe could be upgraded to 65.5 per cent Fe at 50 per cent overall recovery with simultaneous decrease in SiO2 and Al2O3 content to 2.3 per cent and 1.8 per cent respectively by using oleic acid as the collector. In the case of sample II, it has been established that reverse flotation of silica is the better technique to improve both the grade and recovery of iron. Batch flotation studies in cell indicated that a product with 63.1 per cent Fe could be obtained at 40.0 per cent yield with 63.6 per cent iron recovery by the combination of reagents such as gum acacia, sodium hexa meta phosphate and dodecylamine. The performance of column flotation techniques is far superior to that of the cell with respect to both grade and recovery. The concentrates are found to be quite suitable for commercial exploitation as pellet feed.

Jan 1, 2005

By M Ridd

The Pasminco Century Mine (PCML) is located 250 kilometres north-north-west of Mt Isa in Queensland. As one of the worldÆs largest zinc mines, PCML comprises mining and milling operations at Lawn Hill, concentrate filtering and shipping facilities at Karumba in the Gulf of Carpentaria, and a 304 km slurry pipeline connecting the two operations.Mineralisation at Century occurs in the upper part of the Lawn Hill formation and is comprised of siltstones, shale and sandstone. Pyrite occurs immediately above the mineralised sequence, and throughout the footwall carbonaceous shale forming the lower proportion of the deposit. Zinc predominantly occurs as sphalerite (ZnS) and lead as galena (PbS). These sulfides are very fine-grained and may oxidise rapidly upon exposure. The pyrite, sphalerite and galena are the main potential sources of acid rock drainage (ARD) or heavy metal leachate at the mine site.To minimise the generation of ARD in the waste rock dumps, they are constructed in a specific manner and waste rock is classified into the following three classes based on competence and acid forming/consuming capabilities:Class 1: Competent rock, non-acid forming or acid-consuming material. Class 2: Non-competent, non-acid forming or acid-consuming material. Class 3: Acid-forming material. The generalised Waste Rock Dump Design for current operations comprises an outer zone of Class 1 material and inner zone with Class 2 and 3 material. Limestone is the Class 1 material used for both its structural support and acid neutralising capacity. Reserves of limestone at the mine site are limited. Net acid generation (NAG) tests confirm that a mix of limestone and shales can be net acid consuming.Field based and laboratory based trials have been established at PCML to quantify blending levels of limestone and shale that will produce leachates both neutral in pH and low in metal/salt concentrations. This paper will discuss the first six months results (of a two-year sampling program) from the trials.

Jan 1, 2004

By K Brand, M J. Ind, M Rynhoud

Water management at a tailings storage facility (TSF) presents one of the major risks to the safe performance of the facility. International and domestic dam safety guidelines assess a dam’s hazard category based on the consequences of a dam failure and the subsequent downstream damage to the environment and communities.Often a rigorous risk assessment is undertaken during the design stages to identify and control hazards associated with water management through life-of-mine (LOM) phases. However, as experienced during the recent downturn in commodity prices, early closure of a mine can occur rapidly and unexpectedly. Although guidelines such as the Australian National Committee on Large Dams Incorporated (ANCOLD) recommend that one of the key objectives of integrated TSF planning is to ‘plan all phases of a tailing dam’s life to ensure adequate storage capacity including early closure ’ (Australian National Committee on Large Dams Incorporated (ANCOLD), 2012) this is often overlooked by owners who are focused on fulfilling the mine’s potential and early closure is not on their radar.CITATION:Ind, M J, Rynhoud, M and Brand, K, 2016. Life-of-mine spillway strategy – managing risk associated with surface water at a tailings storage facility, in Proceedings Life-of-Mine 2016 Conference, pp 209–211 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By D Reid

Many of the relevant engineering behaviours of tailings are controlled to a large degree by the density of the material. For example, loose tailings are prone to brittle strength loss, while dense tailings are dilative (i.e. gain strength) at large shear strains. The critical state framework has been successfully developed over the past few decades to assess whether in situ conditions are contractive or dilative, and estimate relevant engineering parameters on that basis. Tailings comprising primarily silt-sized particles, when subaqueously deposited, often form a particularly loose state compared to subaerially deposited material of similar index properties. Such subaqueous deposition occurs in the decant pond area, where the tailings typically pluviate in quiescent conditions within a pond of standing water. Silt tailings deposited in such a manner have been observed to be extremely loose in a number of TSF investigations. Of particular concern, the deposited material in such cases appear to be significantly looser than can be reproduced in the laboratory - even using moist tamping, the sample preparation method which can usually produce the loosest samples possible in laboratory conditions. While the loose density of subaqueously deposited silt tailings is clear, in a well-managed upstream-raised TSF the decant pond is usually small and far from the perimeter embankments, however there are a number of examples where the engineering performance of such materials becomes relevant – for example, when historical deposition practices were poor, resulting in subaqueous deposition near the perimeter embankment. This paper outlines the geotechnical characterisation of a number of such subaqueously-deposited zones, compares the in situ state to that achievable in the laboratory, and discusses options for assessing the expected engineering performance of such materials when comparable laboratory tests are unavailable.

Jul 1, 2021

A variety of algorithms and methods are being used by the mining industry today to map mineral resource for reserve estimation. The traditional methods including Polygonal, Sectional and Inverse Distance methods are relatively easy to understand and implement. They have served industry well for several decades and should continue to do so for the large bulk mineable deposits with very regular geometries with relatively small variation in grade.

Jan 1, 1992

By Hoskings R

Conceptual studies of the run of mine stockpiling and reclaiming requirements com- menced in 1975. Final selection of equipment was made in 1978 and the equipment was commissioned in June, 1979. Equipment selection was made after extensive investigation and visits to existing facilities throughout the world. The equipment selected is described and com- pared with the alternatives. Foundations were designed to minimise clean up effort and to ensure stability of equipment under design wind loading without storm bays. Program- mable logic control enables the stacking and reclaiming facility to provide a blended feed to the coal preparation plant.

Jan 1, 1980

By D Wei

Large tonnages of low-grade haematite ores need to be treated every day in China. One of the mineralogical characteristics of these haematite ores is that the grain size of haematite is smaller than that of quartz and is not uniform in the ores. Therefore, a flow sheet consisting of gravity concentration, low-intensity magnetic separation, high-intensity magnetic separation and reverse flotation is mainly used to separate haematite ores in China, to obtain acceptable beneficiation performance and reduce the operating costs. Nowadays, whether based on mineral processing practice or theoretical analysis, the results show that the application of the above-mentioned flow sheet is able to take full advantage of these mineral processing methods and achieves satisfactory benefi ciation of haematite ores. For example, when the iron grade of the haematite ore is about 29 per cent Fe, a concentrate assaying 68 per cent Fe can be obtained and the recovery of iron is over 80 per cent. In the future, research work on the beneficiation of haematite ores should focus on investigating the most feasible particle size for gravity concentration circuit feed so that the operating costs can be reduced and ultimately the separation performance can be improved.

Jul 11, 2011

By Vestre J, Kure K, Bergqvist I

Existing practical laboratory tests for comparative strength determination of commercial explosives consist of the lead block test, the ballistic mortar test, the bubble test etc. These tests are carried out in material with quite different properties compared to rock. The theoretical performance potentials of commercial explosives are traditionally described by weight-strength (WS). Some explosive producers use the Langefors formula for weight-strength calculation, where also the gas volume is considered. Neither the theoretical nor the practical methods for determination of explosive performance such as the above, give good enough prediction of fragmentation and heave in rock blasting. For these reasons a project was started for the purpose of finding a small scale test method which predicts how different explosive parameters affect fragmentation and heave. Small scale tests were carried out by using 50 cm cubical blocks, mainly of concrete, but a few also of rock. All blocks were blasted in a steel cylinder with a diameter of 1.2 meters. The velocity of detonation was monitored, and the velocity of fragments was derived from their time of arrival at the steel wall, which was registered by accelerometers. After blasting all fragments were screened. The charge diameter was 22 mm and the amount of explosive 78 grammes, resulting in a specific charge of 0.62 kg/m3. Explosive properties such as energy, gas, VOD and density were systematically changed.The results presented in this paper show how fragmentation and heave systematically change when the explosive properties like energy, gas, VOD and density are systematically changed. The results from the small scale tests are compared to full scale tests carried out in tunnel blasting, and during summer 1990 also in bench blasting.

Jan 1, 1990

By C I. Edwards

Phosphorous is typically present in iron ore either in the mineral apatite, Ca5(PO4)3OH, or associated with the goethitic fraction of the ore. In this paper, we present results that show that phosphorous associated with the goethitic fraction can be removed with a heating pretreatment around 300 176;C for 1 h, followed by a caustic leach with 1 - 5 M NaOH, or a leach with sulfuric acid at pH 0.5. The heating pretreatment is considered to dehydroxylate the goethite to form a haematite intermediate phase, ‘protohaematite’, that reacts during the leach making the phosphorous accessible to the leachant. In the acid leach, ten to 15 per cent of the sample was dissolved to obtain a leach product with 0.08 per cent P. In the caustic leach, as no weight loss occurs, it is proposed that iron species associated with the protohaematite have either not dissolved or have reprecipitated at the high pH values of the leach.For an ore containing apatite as the source of phosphorous, a leach with sulfuric acid dissolved the apatite, lowering the phosphorous levels in the sample. The sample treated contained carbonate minerals (including siderite) that also reacted with the acid, and in practice a balance between the dissolution of the apatite and the carbonate minerals may be needed to minimise acid consumption.

Jul 11, 2011

By T Roberts, D Faulkner, G Watt

Traditional mechanised resin rock bolting in hard rock underground mines requires the installation of resin capsules into a pre-drilled hole prior to the rock bolt being spun into a hole to mix the resin and set the bolt in place. In poor rockmass conditions, especially at depth or in highly altered faults and shears, the condition of the holes often deteriorates as the poor ground around it unravels and falls into the hole. This results in partially or fully blocked holes that either damages the resin capsule when they are being inserted into the holes or prevent it entirely until the hole is continuously cleaned of debris. This deterioration of the hole condition, and continuous need to clean and re-drill holes, also increases the diameter of the hole which in turn affects the continuously mechanically coupled anchorage mechanism of the rock bolt to the rockmass as there is simply not enough resin in the hole to fill the annulus between the bolt and the rock. This results in a large increase to critical heading cycle time and, more importantly, results in the rock reinforcement not performing as per design specification and increases the risk of instability. To overcome the quality control issues with resin bolt installation in poor ground, a single pass drill, install, inject and tension self-drilling resin bolt application was designed and implemented for use in such conditions. This system allows the operator to inject a two part polyester resin through a self-drilled hollow bolt to mix and fully encapsulate the rock reinforcement. The self-drilling bolt allows for post injection of the hole after the bolt has been installed into the rock and gives the operator manual or automated control on the amount of resin used in the hole to ensure complete encapsulation and continuously mechanically coupled anchorage to the rock. This allows the reinforcement to work as designed and provide the Geotechnical Engineer extra quality control confidence in these conditions. The implementation of this single pass resin bolting system resulted in significant decreases to the resin bolting cycle time and rock bolt quality control failures. In this paper the design, implementation and embedment into the development cycle will be discussed and the in situ quality control checks used to validate the increase in rock bolt installation quality will be shared. CITATION:Watt, G, Roberts, T and Faulkner, D, 2018. Single pass drill, install and inject self-drilling resin bolt application in poor ground, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 323–343 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By E Villaescusa, C Drover

The stability of access tunnels is one of the main engineering challenges in deep underground mine construction. Many underground hard rock mining operations are now reaching depths where the induced stresses are such that sudden and violent failure of the excavations can occur very soon after construction. The loading conditions on the installed ground support schemes are often underestimated by conventional engineering design methods. Therefore, the actual loading conditions often exceed the installed ground support capacity. This can result in failure of the excavations and, in extreme cases, potentially closure of mining operations amounting to hundreds of millions of dollars in lost production. More frequently, violent excavation instability at great depth causes operational delays, costly and unplanned rehabilitation, as well as risks to worker safety. In order to address this challenge, this paper briefly summarises a modern, innovative approach to the design and construction of mine development at great depth. The process follows seven main steps. The first step is to characterise the rock mass strength, structure and stress. The second step is a stability assessment, which identifies the plausible modes of excavation failure, based on the rock mass characterisation. The third step is the definition of an excavation geometry which is harmonic to the high stress conditions. The fourth step is to prepare a site-specific face destressing drill and blast design which will reduce the potential for rock mass instability during the development construction cycle. The fifth step is to accurately quantify the expected loading conditions on the installed ground support. The method of doing so is uniquely analytical and probabilistic. It is based on the natural mechanical relationships between rock strength, structure, induced stress and the physical characteristics of the instability, including its mass and ejection velocity. The sixth step of the design process is to specify a ground support scheme arrangement with sufficient strength and displacement capacity to exceed the rock mass demand by a safe margin. The final stage is to install the complete ground support scheme using mechanised technologies which minimise the exposure of the equipment operators to unsupported ground at the tunnel face.

Nov 29, 2022

By R Minnitt

Two methods of calibrating the parameters K and Alpha for use in Gy’s formula for the fundamental sampling error were investigated. Approximately 480 kg of broken ore from Harmony’s Target gold mine in South Africa was used to compile the replicate samples for two experiments. The duplicate series analysis (DSA) and segregation free analysis (SFA) methods differ in terms of their approach to recovering the sized materials required for the calibration procedure. In this experiment the DSA method split off six more-or-less equal masses of material from a 75 kg lot that was successively crushed to finer and finer fragment sizes. The sublots so formed were split into 32 samples and fire assayed for gold. The SFA method used approximately 250 kg of broken ore crushed to 95 per cent passing 2.50 cm, which was then passed through successively finer screens until a sublot of less than 0.0075 cm was obtained. Each of the 15 sublots obtained in this way were split using a riffle splitter into 32 samples that were fire assayed. A total of 672 fire assays were used in these experiments. The sampling parameters K and Alpha were used for the compilation of a nomogram and to calculate the gold liberation size of the ores. While there are no definitive results in terms of the actual gold grain sizes against which the calculated sizes can be compared, it appears that the DSA method produces more acceptable results.CITATION:Minnitt, R, 2014. A comparison of two methods for calculating the constants K and alpha in a broken ore, in Proceedings Sampling 2014 , pp 165–178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

At Renison Limited, on the West Coast of Tasmania, modern trackless decline mining is practised to exploit the various tin bearing sulphide deposits. With footwall accesses, one of three adaptations of horizontal mechanised cut and fill, 1. unsupported, 2. pillar supported,and 3. unsupported - resuing is used to stope each defined ore block. The stoping method is basically determined by the dip and true thickness of the ore with emphasis on high ore recovery. Extreme flexibility is possible by the selective mining of stope lifts, the consumption of development waste as fill and the utilisation of the same mobile equipment in all phases of production. This has resulted in high productivity and low cost per tonne of ore.

Jan 1, 1977

By Gregg PEH, Horne D, Bolan N, Stewart RB

The Tui mine site is situated on the NW flank of Mt. Te Aroha, at approximately 400 m altitude. During underground mining operations two lead-copper-zinc ore bodies were exploited and processed on site. The legacy of the mining operation is a barren dam containing over 100,000 m3 of sulphide-rich tailings. The Tui mine site is arguably the worst case of environmental degradation resulting from past mining activity in New Zealand. Although the impacted area (approximately 4 ha) is extremely small by international standards, acid mine drainage (AMD) emanating from the abandoned tailings dam and mine adits has severely contaminated local streams and prevented natural plant recolonisation of the site for more than 20 years.

Jan 1, 1995

By S M. Stewart

Industry, especially extractive industry, must now give serious attention to the impact its operations have on the natural environment and on the economic, social, and cultural context within which it operates.   While this obligation is statutorily managed, there has been a recent shift towards a culture of self responsibility. Industry is now talking about earning its ôsocial licence to operateö and the importance of maintaining the ôtriple bottom lineö, thus adding environmental and social performance to the usual financial criteria used to measure organisational performance. The social context within which companies operate has also become more sensitive with industry responding to a growing public expectation that it conduct itself in a way that strives for sustainability by operating and developing in a way that meets the needs of the present without compromising the ability of future generations to meet their own needs.   There are glowing accounts of industries engaging and collaborating with the communities within which they are based. In amongst these are also some disasters which result from cultural assumptions, industry created dependencies and the failure to attain community buy-in despite significant investment by the industry involved.   There are also remarkable stories of communities, and action groups within communities, being a significant catalyst for positive change of their natural, cultural and social environment. In amongst these stories there are also accounts of long and drawn out battles; adversarial situations where no one wins; a litany of mistrust, tricks and tactics, with the better resourced party ultimately achieving its primary objectives at the cost of the other (and at the cost of any potential fruitful, mutual relationships).   So what makes the difference in achieving the positive rather than negative outcomes? The answer lies in the way the outcomes are achieved. Building relationships based on good communication, respect for divergent views, mutual understanding, and the development of trust and empathy, makes it possible to identify shared goals and objectives that best meet the needs of all parties.   Research indicates the mining industry is making good progress in developing policy and commitment to community development and engagement but that, ætranslating commitments into improved practices at the site level remains one of the industryÆs toughest challengesÆ. (Australian Government - Community Engagement and Development Handbook October 2006 @ page 49.)   This paper considers the merits of a process of community collaboration and what it has to offer in terms of meeting that challenge.

Jan 1, 2007

By D M R Stone

Failings di,posal presents many challenges at metal mines in Peru where the extreme relief yields very little useable land area. These challenges are amplified by other hazards such as the high seismic environment, high rainfall, and frequent debris torrents down the steep hillsides. As a result many mining operations have resorted to in-river disposal of mill tailings. This paper presents a case history of one underground metal mine located in the high Andes mountains of Peru where in-river disposal of tailings has been used for some 30 years. The paper outlines a comprehensive engineering study that was aimed at increasing the utilisation of tailings disposal underground. The scope of this study included modifications to the grinding and flotation circuits to produce a high sulphide and low sulphide tailings for underground and surface disposal respectively: mapping and cataloguing of abandoned stopes for hackfilling: modifications to the existing backfill system to improve icliahility and throughput, and a preliminary evaluation of alternatives Such as silicated and paste fills.

Jan 1, 1998

Geological hazards such as faulting, basement ridges, and zones of "thin" (

Jan 1, 1998

A very wide range of technologies are utilised in the mining and processing of ores and a great deal of effort is expended in the development of ænew technologiesÆ to improve mining performance and economics. Traditionally, technology and people have been treated as separate aspects of an operation, when in fact they are inextricably linked. The successful implementation of new technologies is entirely dependent upon the actions, enthusiasm and skills of people, both as individuals and working in groups. This paper discusses the role of technology in mining and how new technologies are implemented by the industry. The paper argues that existing technologies have not been fully or adequately utilised and that effort should be re-focussed on the implementation of technologies that have been taken for granted for many years. The need for greater emphasis to be placed on the management of the human-technology interface is discussed.

Jan 1, 1998

By P Breuer, X Dai, A Bergamin, D Hewitt

"Copper-ammonia-thiosulfate?leaching of gold has been researched for several decades as a potential alternative to cyanidation. However, this technology has not yet been applied commercially due to many challenges such as complex solution chemistry, reagent degradation and losses, system instability with losses of precious metals and difficulties in gold recovery from the leachate. Progress has been made at CSIRO in tackling some of these challenges including:better understanding and control of the leach conditions to minimise reagent losses whilst maximising gold recovery use of strong base ion exchange resins to recover the gold strategies to deal with polythionates that adsorb competitively with gold on ion exchange resins development and evaluation of process flow sheets.As a result there has been increased interest from the gold industry and renewed activities to develop thiosulfate based processes for gold recovery. One application area, which has been developed to the point of piloting, is the treatment of gravity gold concentrates using a copper-ammonia-thiosulfate leach with ion exchange recovery of the gold thiosulfate. This paper describes some of the advancements in the development of a potential process flow sheet for this application.CITATION:Dai, X, Breuer, P, Hewitt, D and Bergamin, A, 2013. Thiosulfate process for treating gold concentrates, in Proceedings World Gold 2013, pp 61-70 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 26, 2013

By R Williams, M Baxter, D Zink, R Cunningham

The purpose of this paper is to discuss the efficient operation of a tailings dewatering circuit comprising a thickener and filter press through proper control and automation. It is common to see thickeners and filter press circuits each with their own control systems. This can cause multiple issues when trying to increase efficiency and reliability of the tailings management process. By automating the thickener and filter press controls, you are eliminating any delays and inconsistencies caused by human error and process variations. When done properly the system can maintain a consistent product as the feed characteristics change. Previously, operators would have to monitor the process parameters and adjust the system accordingly. This can now be accomplished using state of the art process control equipment that continuously monitors and adjusts critical variables using Programmable Logic Controllers (PLC) and Proportional Integral Derivative (PID) loops. The paper will detail the control theory used to maintain these systems, highlight other benefits of having a fully integrated plant such as predictive maintenance and remote diagnostics as well as present examples of how these have been implemented in field examples.CITATION:Baxter, M, Cunningham, R, Williams, R and Zink, D, 2018. Tailings process optimisation through automation and controls integration, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 416–421 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018