Search Documents

By K R. Vining, T E. Norgate

A study was carried out to compare the environmental impacts of the two major iron ore agglomeration processes, sintering and pelletising, using life cycle assessment (LCA) methodology. The following agglomeration processing routes, with the fuel options shown, were investigated:sintering with combined natural gas/coke breeze or charcoal as fuel, grate-kiln pelletising with combined natural gas/coke breeze as fuel, and straight-grate pelletising with combined natural gas/coke breeze as fuel. Inventory data for each process derived from the literature, and in some instances supplemented by additional simulations and calculations, were used in the study and the environmental impact categories considered were gross energy requirement (GER), global warming potential (GWP) and acidification potential (AP). The results of the study showed that the GER, GWP and AP for a sinter plant are higher than those for a pellet plant for the same amount of metallic iron in the agglomerated products. These results are partly due to higher consumption of solid fuel and flux in the sintering process. However, it should be pointed out that the study only compared substantially fluxed sinters with acid pellets that may require additional flux (and hence potentially more greenhouse gases emissions) to be a balanced blast furnace feedstock. Extending the LCA to the blast furnace process stage was beyond the scope of the current study. Within the sinter plant, the sintering stage itself is the largest contributor to the GER, GWP and AP. In the case of pellet plant, the pellet induration stage is the largest contributor to the various environmental impacts. The GER and GWP of a straight-grate pellet plant are marginally higher than those of a grate-kiln pellet plant due to the higher electrical power required by the straight grate system. The substitution of coke breeze with charcoal in the sintering process results in an increase in GER but a decrease in GWP. However, a substantial proportion of the GER is derived from renewable sources (wood), resulting in a decrease in the non-renewable components of this environmental impact. Given the source of the inventory data and the assumptions and approximations made in carrying out the LCAs, it is emphasised that the results presented in this paper should be considered as indicative rather than as definitive results for the two iron ore agglomeration processing routes considered.

Jan 1, 2006

By M Edgar, G Pattemore, M Auad, K Job, A Job, S Gale

In recent decades, significant advances have improved the modelling techniques for predicting slope failure. Predicting failures is vital in open pit mining due to the significant risk posed to personnel and equipment from unstable pit walls. Failures not only cause harm and damage to people and equipment but also cause delays to production and subsequently increase operational costs. Coupled with improvements in modelling techniques, utilisation of advanced scanning systems, such as high-definition imagery from UAVs has enabled faster and more precise mapping and modelling. However, one key element required for accurate slope stability modelling and monitoring is the ability for mine geotechnical engineers to have an accurate understanding of the mineralogy and moisture content of slopes, in real-time. To address this challenge, research has been undertaken to utilise hyperspectral imaging across a broad spectrum, combined with high-definition imagery, and LiDAR to scan slopes for minerals and moisture content. In addition to accurately mapping mineralogy and moisture, the data must be collected autonomously and remotely to ensure ongoing safety. The results show that there are many direct and indirect benefits from this new technology, including the ability to monitor slopes at a safe distance and in real-time, improved accuracy of modelling, detection of risks, and improving the automation workflow for geotechnical engineers. The paper presents recommendations for the implementation of the technology in open cut mining environments.

Jun 22, 2022

By U König

The use of high speed detectors made X-ray diffraction (XRD) an important tool for quality and process control in the mining industries. Besides knowledge about the mineralogy of a sample it provides useful information in terms of quantification of the crystalline phases and the amorphous content. Cluster analysis of XRD data can facilitate multi-dimensional mapping of ore deposits and drill cores, identifying regions of favourable mineral compositions. The studies of this paper demonstrate how XRD and data clustering can be used for grade control, process optimisation and quality control of iron ores and iron ore sinters. These new developments have an enormous potential as an inexpensive, reliable tool, useful in the characterisation of iron and sinter materials implemented in an industrial environment.

Jul 11, 2011

By D Smith

The Broken Hill deposit is located in Australia in the far western region of New South Wales. The deposit was found in 1883 and has been mined continuously since its discovery. It is considered the largest lead, zinc, silver deposit that has been discovered in the world and originally contained around 340 Mt of ore at a grade of around 12 per cent lead, ten per cent zinc and 150 g/t silver. The material remaining in the deposit represents only a fraction (perhaps ten per cent) of the original resource. Several of the world’s largest mining companies can trace their origins to the Broken Hill Field. The remaining resources on the CML7 consist of two large lower grade resource lodes that have not been subject to mining, some scattered areas of zinc lode material and the pillars and remnants of the main lead lodes.The deposit occurs in metamorphic rocks of the Broken Hill Group a division of the Willyama Super Group contained within the Curnamona Craton. The Broken Hill Group rocks have undergone multiple phases of deformation. Metamorphism is granulite grade with major shears cutting through the deposit having been retrogressed to mica schists. The deposit lies in an antiform associated with the second phase of deformation.The resultant proposed mine is situated on Consolidated Mining Lease 7 (CML 7) which occupies a strike length of 3.6 km in the central part of the 7.8 km long footprint of the orebody. Underground mining on CML7 ceased in 1975 with surface mining of silver chlorides in the weathered zone continuing until 1991. CBH Resources has been continually working to define and evaluate the remaining resource since 2002. This work has included four surface drilling programs, two underground drilling programs, an exploration decline, enormous amounts of compilation of historical data and detailed three- dimensional (3D) modelling of historical mining and the resource lodes. It is currently planned to commence production at the Rasp Mine in late 2011. The operations will produce from previously unmined lodes and from remnants and pillars.This paper primarily aims to encapsulate the processes involved from information acquisition through to resource estimation and also to highlight some of the challenges encountered and the specific techniques and practices used to overcome them. Many of the experiences at Broken Hill are applicable to all brown field sites.

Aug 22, 2011

By P Marlow

Raiseboring is an attractive method of constructing shafts, being safe, fast and comparatively cheap. But this means back-reaming through weathered ground. However in the gravels and weathered near-surface rocks typical of the Western Australian goldfields, back reaming large diameter shafts through to the surface is risky and conventional sinking from surface has normally been required.An alternative construction approach has recently been used to stabilise the weak surficial materials and allow raiseboring through to the surface. The method is based on first installing rings of non-contiguous reinforced bored piles around the shaft perimeter, for temporary support, then back reaming shafts at full diameter through to the surface. Immediately after the reaming head is removed, the weak exposed materials are supported using remotely sprayed fibrecrete.The method has been successfully applied to four shafts since July 2007; 3 m and 4 m diameter shafts at Trident Mine, a 3 m diameter shaft at Wattle Dam and a 4.5 m diameter shaft at Athena Mine.Bored pile layout designs have varied from eight to 24 piles, of diameters 120 to 270 mm, in one or two rings. In one case, the top 10 m of the proposed shaft was pregrouted. Subsequent surveys have confirmed that fallout occurred in some shafts, out to the ring of piles, implying that the piles inhibited collapse.The practical implementation of the method was not always easy and many valuable lessons have been learnt. This paper documents key aspects of the method and the critical elements for its application.

Mar 21, 2011

By C W. Davis

Every diesel engine emits approximately 100 million nano diesel particles (nDP) per cubic centimetre of raw exhaust. Each nDP has a diameter of between 50 and 70 nano metres or 1/100th the size of red blood cells (diameter of between 6 and 8 microns). When inhaled, some nDP pass through the lungs and penetrate all body tissue [1]. Europe and North America have recognised and are addressing the long term health problems posed by nano diesel particulate matter (nDPM) across their societies [2.3]. Australia has been slow to recognise the issue, at both a societal and mining industry level. There are chronic health effects for every underground miner and serious legal issues for mining companies with increasingly stringent Occupational Health and Safety legislation being implemented at a state level across Australia. This paper will review progress within Australian society and more particularly the underground hard rock mining industry, particularly in Western Australia (WA).

Mar 15, 2021

By G Sparrow

The Murray Basin is being heralded as the next major mineral sands province in Australia. Already exploration programs have delineated extensive commercial deposits and several companies are progressing with plans to produce zircon, rutile and ilmenite in the Basin. As these deposits are developed consideration will need to be given to several key issues of the Murray Darling Basin; the availability of fresh water and management of salinity in the area being two of them. In this paper ideas being developed in CSIRO that link the processing of mineral sands with the salinity problem in the Basin are presented. The proposal presented here is to process saline water to produce industrial minerals with large volume applications and to produce value-added products from the mineral sands in the Basin using reagents produced from the saline waters. Processes to produce titania pigment and zirconia consume chlorine, caustic soda, soda ash and hydrochloric acid, all derivatives of salt (sodium chloride). There may be a good economic incentive if these processing plants were located in the close vicinity of each other.

Jan 1, 2001

By K Nesbitt

Draw control at Premier Mine is considered important to avoid conditions of isolated draw, which results in early waste ingress, compaction of the kimberlite ore and loss of ore reserves. The Premier Mine kimberlite pipe is unique in that the pipe is cut at a depth of 400 metres below surface by a 75 metre thick gabbro sill. All cave mining at Premier is below the sill and failure to exercise good draw control could cause early ingress of gabbro waste. Gabbro causes problems in the diamond recovery plant and the amount of gabbro sent to the plant needs to be closely monitored. Fortunately coarse gabbro fragments are easy to recognise in drawpoints. It was anticipated that only 85 per cent of available ore would be drawn from the blocks immediately overlain by the gabbro sill before excessive gabbro waste forced the closure of drawpoints. Data on tons drawn per drawpoint and loaded per LHD as well as the tons tipped per pass is gathered by the vehicle monitoring and control (VMAC) system and information recorded by the load-haul-dump (LHD) drivers. Draw control staff monitor drawpoints on a shift basis and record the occurrence, type and height of hang-ups. Information pertaining to the status of the drawpoint in terms of support, waste and availability is also recorded. A database has been compiled that has been used to analyse the overall pattern of draw control, the frequency of occurrence of different types of hang-ups, secondary blasting efficiencies and drawpoint and LHD productivity. The gabbro sill has provided a unique marker horizon that has allowed the arrival of rock from a level 100 metres above the production level to be recognised. Data shows that ore migrates extensively towards groups of drawpoints that are heavily drawn with many drawpoints more than 100 per cent drawn before gabbro waste was recognised. This indicates that an accurate mixing algorithm is essential for good draw control. Data on tons drawn, drawpoint availability, productivity and the occurrence of various types of hang-ups has allowed better control of the mining operation and provided data for planning future caves. In the BA5 mining block a drawpoint spacing of 22 metres, horizontally across the major apex, has still allowed drawpoints to be pulled to waste with no loss of ore. In the BB1E mining block the drawpoint spacing has been increased to 23 metres and no problems have been experienced to-date. Future initiatives centre on improving the data gathering integrity of the vehicle monitoring and control system and a linear programme that will optimise draw control and productivity.

Jan 1, 2000

By J Siliézar

The Ernest Henry Mine (EHM) is situated 38 km north-east of Cloncurry in the Mount Isa – Cloncurry mineral district of northwest Queensland. The EHM orebody is an iron oxide copper gold deposit with an average grade of one per cent copper, 0.5 g/t gold and 23 per cent magnetite, with current reserves of approximately 88 Mt.The copper concentrator is a single line plant with a nominal throughput rate of 1300 tonnes per hour. An average of 350 000 tonnes of concentrate is produced each year containing around 100 000 tonnes of copper metal and 120 000 troy ounces of gold.In December 2009, Xstrata Copper announced approval of a $589 M investment to extend the life of EHM to at least 2024, through the transformation of open pit mining operations to a major underground mine together with the construction of an associated magnetite extraction plant.The EHM magnetite plant extracts the magnetite from the copper concentrator’s tailings stream. It will produce approximately 1.2 Mt of magnetite concentrate per annum at full capacity for export to Asia, making EHM Queensland’s first iron ore concentrate exporter. Construction of the magnetite extraction plant commenced in July 2010 and was completed in January 2011.This paper gives an overview of the development of the EHM magnetite extraction plant flow sheet from the early mineralogy and laboratory test work through to the plant commissioning and early operation of the base plant. It has a major focus on the commissioning learnings from the plant start-up and includes a review of the operational performance of the plant versus original design and expectations.

Jul 11, 2011

By H Kundapen, B R. Bolton, H Davies

The Ok Tedi porphyry copper-gold mine is located in the Star Mountains of Western Province, Papua New Guinea. Open-cut mine commenced in 1984 and is due to cease around 2010. The mine produces a total of 88 Mt of waste annually including 58 Mt overburden and 30 Mt tailings, which are discharged directly in to the Ok Tedi River. Mine derived wastes are transported downstream and deposited within the river channel in a variety of bar forms. The prevailing hydrogeological conditions including, velocity, competency, capacity, gradient, grain size and specific gravity, control the deposition and segregation of these sediments. Periodic exposure of the reactive sulfides to oxygen during fluctuations in the river discharge may result in oxidation, localised acid generation and liberation of metals into solution. To evaluate the significance of this issue, Ok Tedi Mining Limited initiated an investigation of the sediments deposited in the upper Ok Tedi River as part of its overall ARD Management Program. The specific objectives were to: evaluate the acid-forming characteristics of identified high sulfide river deposited sediments; characterise geochemically the waters in contact with sulfide-bearing river deposited sediments; map and monitor exposure areas and oxidation depth of deposited potentially acid forming (PAF) sediments; determine the depositional processes controlling sulfide distribution; and assess lag period, oxidation and metal release rates for the sediments. This work included the analysis of sediment and water samples collected on a 50 + 50 metre grid at six gravel/sand bars. The sediment samples were analysed for total sulfur, ANC, NAG, total sulfur and total copper. Water samples were tested for general water quality parameters, sulfate and a suite of dissolved metals including; Al, Ca, Cd, Cu, Fe-sol, K, Mg, Mn, Na, S and Zn. This paper presents the results of these investigations with particular emphasis on the geochemistry of the river sediments and associated contact waters.

Jan 1, 2003

Recovery Process of Carbon Dioxide with Metal Oxides and Metal Hydroxides

Sep 13, 2010

By D Morgan, D Sato, B Lumsden, S Senanayake

Laboratory flotation tests on fresh cyclone overflow samples are a useful tool to troubleshoot and indeed to improve plant performance; however, reproducibility between laboratory flotation test and plant performance is important for interpretation of the laboratory tests and hence their usefulness. Chemical reproducibility can be achieved with the addition of the required reagents; however, reproducing the physics of forces and energy in a 5 L cell compared to a 50 000 L plant cell or a 500 000 L plant cell is not generally studied or discussed. For some tests such as collector evaluation the physics of the flotation process may not be critical, but for some evaluations in the laboratory, it can be important.All flotation plants suffer from losses of valuable <20 µm mineral. Selective mineral aggregation has long been recommended to improve the poor flotation recovery of <20 µm sulfide minerals; however, successfully testing any type of selective sulfide mineral aggregation’s effect on flotation recovery in the laboratory on practical plant samples requires reproducing plant cell physics. The energy input per litre and the forces in a laboratory cell are vastly different to a plant cell. Reproducibility between laboratory and plant tests requires that these differences be minimised. The physics of the laboratory flotation cell is particularly important when fine mineral aggregation tests are carried out.This paper outlines a modified laboratory aggregation and flotation method that closely reproduces plant performance in a laboratory test.CITATION:Sato, D, Lumsden, B, Senanayake, S and Morgan, D, 2014. Development of a laboratory flotation method to test plant mineral aggregation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 173–178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By D Connelly

Quartz deposits are common in nature but the presence of quartz suitable for yielding high purity quartz is exceedingly rare. This paper describes a test work study on producing high purity quartz (HPQ) product to meet the tight product specifications of greater than 99.97per cent, including four and even five nines, for uses including, lighting and fibre optics and modern-day high efficiency solar panels. Due to demand in renewable energy applications the market for high purity silica solar panels known for their increasing efficiency and durability is rapidly growing. Demand continues to rise for the use of high purity quartz in semiconductors, electronics, imaging and sensor markets. Microelectronic components are created by chemically fabricating wafers of semiconductors such as silicon to obtain the desired transport of electrical charge and control of the current. The production of silicon metal from high purity quartz has been designated a Strategic Mineral by the European Commission and by the US Department of Justice due to the growing significance of this metal in various industries. The subsequent processing of quartz is the key step to adding value and aiding technological advances. Overall, the high purity quartz market is a highly secretive, specialised market with increasing opportunities for stakeholders. The attempt to produce HPQ in this work was carried out using an Australian quartz ore following a typical HPQ process flow sheet. The unit processes included primary crushing, scrubbing, magnetic separation, flotation, acid leaching followed by hot chlorination. The results indicate that grinding of quartz requires specialist equipment due to the hardness and extreme abrasiveness of the ore leading to additional iron contamination in the ground ore. The critical impurities were aluminium, iron, sodium, potassium, lithium, titanium, zircon, calcium and magnesium. The chemical refining was found effective. The hot chlorination process needed to be done at 1200°C in a chlorine – hydrogen chloride gas atmosphere. The risk of any gas being released during this stage is very serious and only specialist companies should and can carry out this step. More recent studies reported many new options that appear to facilitate the production of HPQ with the requisite purities more easily, but costly equipment along with highly trained operators are required and hence unlikely to become available in standard metallurgical laboratories any time soon.

Sep 1, 2024

By M G. Wansbone, R Bhargava

The inferred ground conditions for the proposed mined cross passages at the northern end of the Waterview Connection tunnels consist of an overburden of alluvial and residual soils, with mixed face geology of highly weathered to unweathered extremely weak rock. This paper describes three-dimensional (3D) finite difference analyses undertaken to evaluate the stability of the cross passage headings and to validate the proposed sequence of excavation. The analyses undertaken incorporated the influence of the construction of the mainline tunnels and the breakout opening in the segmental lining for construction of cross passages.The stability analyses were carried out using FLAC3D™, version 4.0 (by Itasca Consulting Group) by progressive reduction of shear strength parameters to obtain a failure condition and estimate a factor of safety. For each step of strength reduction, corresponding increments of displacements of several points on heading faces were monitored. The stability obtained from numerical analyses was compared with analytical solutions. Interpretation of results of drained analyses indicated instability of the upper 2 m of heading face within the highly weathered rock mass. Additional analyses were undertaken by including grouted fibreglass dowels to reinforce the heading face. The results of the additional analyses showed significant reduction in displacements and yielding of ground around the face. The proposed temporary support comprised face reinforcement using grouted fibreglass dowels in conjunction with canopy tubes and perimeter support of steel fibre reinforced shotcrete. The stability of the construction sequence, which was related to the specific requirement of the proposed excavation equipment, was validated.CITATION:Wansbone, M G and Bhargava, R, 2014. Analysis of stability and design of face support for cross passages – Waterview Connection tunnels, Auckland, New?Zealand, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 339–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Weber W

Methods of calculation of the reliability of process computers are getting more and more important. The paper presents long period observations of 21 process computers with online applications in the iron and steel industry. About 5000 failure events during 10 years have been systematically recorded and evaluated. On the basis of these long time observations it is possible to develop a probability model of the failure behaviour of process computers.This failure model is constructed with four different states of the process computer:Working phase, working phase with undetected reasons, repair phase, failure phase resulting from external influences.The model is defined by differential equations for the probability of one of these four phases. Long time observations show, that all of these four phases are closely correlated with the capa-city of a process computer, restarting without detection of failure reason, changes of programs and software, costs and time of repair. So the result of this analysis is a model of failure for process computers, which allows to predict breakdowns of process computers on the basis of external parameters.

Jan 1, 1985

Pilot-Scale Study of Deep Cone Thickener for Phosphatic Clay Dewatering

Sep 13, 2010

By E Nik, A Manzoori, H Namavari, P Witt

The smelter building at Sarcheshmeh Copper Complex, Iran, houses two reverberatory furnaces and five Pierce-Smith converters. Under normal operating conditions SO2 emissions fill the building, posing a major health problem for all workers in the building, and reducing their ability to maintain the plant. The converter fume extraction system was analysed using plant measurements, engineering modelling of the entire system and CFD modelling of the extraction hoods. By applying fundamental engineering concepts, a user-interactive computer program was developed that enabled plant engineers and operators to gain a detailed understanding of the system. In conjunction with plant measurements, the model quantified the amount of inleakage throughout the system, identifying it as a significant contributor to the poor extraction performance. Furthermore, it enabled investigation of the effects of hood gates, converters on line, hood dampers, flue insulation, electrostatic precipitator (ESP) operation, and inclusion of an acid plant. The model gave unprecedented insight into the operation of a counterintuitive buoyancy-driven extraction system.

Jan 1, 2004

By J Zhou, L Crompton, K P. Galvin, J L. Sutherland, C P. Lowes, C Bezuidenhout, J Bijzet

Platinum Group Metal (PGM) bearing ores from the Upper Group 2 (UG2) reef often contain significant concentrations of chromite which can potentially be upgraded to produce a saleable product. A common approach is to implement gravity separation on the PGM flotation circuit tailings. However, where the particle size range of interest is broad and the lower size limit ultra-fine, the challenge is how to maximise the recovery at a saleable product grade without compromising throughput. This study was concerned with the performance of a REFLUX™ Classifier for beneficiation of a PGM bearing chromite ore and the benefits of size classification. The sample had a nominal top size of 0.5 mm and was processed over the complete size range and in two discrete size classes following classification at 106 µm. The primary goal was to produce a concentrate exceeding 40 wt. per cent Cr2O3, ideally approaching 42 wt. per cent Cr2O3, with minimal PGM losses above 106 µm. A major challenge was to process at the required solids throughput in a single stage with the feed pulp density constrained to a nominal upper limit of 30 wt. per cent solids. It was found that varying the controller density set point of the REFLUX™ Classifier produced strong control of the product grade. Products as high as 41.1 wt. per cent Cr2O3 were produced at 78.6 per cent recovery for the +106 µm material, while in the −106 µm portion the product grade was as high as 41.4 wt. per cent Cr2O3 at 83.2 per cent recovery. Processing the feed in discrete size classes enabled the volumetric feed and fluidisation rates to be optimised for a given application; hence, superior performance was achieved at the finer sizes. This work has demonstrated the value in considering feed preparation as well as technology selection in developing a robust process solution.

Aug 24, 2022

By Zani J. A, Jackson W. D

Bauxite was discovered in the Kimberley in 1965 by an Amax field crew. Reserves of 230 million tons, of bauxite. averaging 47% total alumina on Mitchell Plateau and 980 million tons averaging 36% total alumina on Cape Bougainville have been indicated by the results of drilling and bulk sampling. Laterite which contains the bauxite deposits caps basalt and interbedded sandstone and siltstone of the Carson Volcanics formation. Bauxite on Mitchell Plateau is 3.2 metres thick on average and is underlain successively by nodular ironstone, clay and basalt. The major components of the bauxite are gibbsite,boehmite, hematite and goethite containing some alumina, anatase and clay minerals. Quartz and vanadium oxide are minor constituents. Boehmite and hematite are concentrated near the surface, whereas gibbsite and goethite predominate at depth. The bauxite profile consists of ferru- ginous, pisolitic and gibbsitic zones with increasing depth. Cape Bougainville bauxite is 8.6 metres thick on average and of tubular structure; its mineralogy is relatively uniform..

Jan 1, 1973

By P K. Singh

Recent advancements in understanding the detonation process are noteworthy, but they are still based on somewhat hypothetical situations. The actual variables that are essential parts of normal blasting practice have not yet been taken into account in such treatments. These include the various initiation practices employed to detonate a column of explosive, from single point initiation to multi-point initiation in blast holes, and the effect on detonation characteristics of both detonators and explosives under multi-deck and multi-hole blasting conditions. The in-the-hole velocity of detonation (VOD) of an industrial explosive is dependent on explosive’s charge diameter and blasthole diameter. The relationship between blasthole diameter and VOD provides a fundamental guideline to the rate of energy conversion and energy release within the detonation front on the interaction of explosives with the confining medium.The in-the-hole VOD of explosives was measured at four experimental sites in India for different blasthole diameters, ie 150 mm to 311 mm, but for identical explosive composition being same particle size, density, viscosity and loaded into blastholes with the same degree of confinement. The results of the studies demonstrated that there is definite relationship in in-the-hole VOD of the explosive and the diameter of the blast hole. The study also confirmed that the explosives initiated with concentrated boosters yielded higher VOD in comparison to those explosives that were initiated with multi-point priming. The measured increase in VOD of explosives for increasing diameter of holes was up to 24 per cent. The rate of change in in-the-hole VOD of explosives increases with increasing blasthole diameter. It can be further stated that the in-the-hole VOD of the explosive reaches a fairly constant value after reaching a limiting/threshold diameter of 311 mm.

Nov 8, 2011