Search Documents

By D J. Brake

There are many sources of gas in underground mines including development and production blasting, strata gases, spontaneous combustion, diesel equipment, chemicals used for a wide range of functions, welding activities and fires.It is only in relatively recent times that electronic gas monitors (or detectors) have become both safe and affordable for routine use.In modern mines, gas monitors should be in daily use by the ventilation department as well as blasting re-entry (or clearance) crews, and are often used by drilling crews, shift supervisors, hygienists and mine rescue or fire fighting crews.When first released, electronic gas monitors needed to be sent off-site periodically for calibration at a suitable accredited laboratory. Between calibrations, their accuracy was unknown. More recently, ‘bump testing’ and field calibration has become possible on the mine site, improving both reliability and safety as well as reducing the total number of gas monitors that need to be in use.There has been almost an overwhelming increase in the number and sophistication of gas monitor features in recent years. This paper reports on a case study into the key criteria that ventilation practitioners should be aware of with respect to the specification and selection of the most recent gas monitoring systems, and recommends good practice for site-based operation and calibration.CITATION:Brake, D J, 2015. Specification and selection of hand-held gas monitors (detectors) for underground mines, in Proceedings The Australian Mine Ventilation Conference, pp 143–154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By D Craw

Previous studies of alluvial gold in Otago and Southland placer deposits have suggested a gold-mercury association for some deposits derived from Caples Terrane schist, whereas alluvial deposits on Torlesse Terrane basement typically have no mercury. A regional study of gold from Otago Schist vein deposits from both Caples and Torlesse Terranes has revealed the presence of both Au-Ag and Au-Ag-Hg alloys in both terranes. Au-Ag alloy (3 - 4 wt per cent Ag) is typical for gold found in most Torlesse vein deposits, and Au-Ag-Hg alloy (3 - 8 wt per cent Ag, 2 - 8 wt per cent Hg) is found in many Caples vein deposits. Au-Ag-Hg alloys are not exclusive to the Caples Terrane, however, as Au-Ag-Hg alloys with up to 4 wt per cent Hg are found in vein material from the Torlesse-hosted, HydeMacraes Shear Zone. In addition, not all Caples-hosted deposits have a gold-mercury association; gold grains from the Carrick and Invincible gold fields have no detectable mercury. The present study characterises gold compositions from various hard-rock vein deposits and has potential for determining placer-source relationships.

Jan 1, 2003

By L-B Fu and J Tan, J H. Wei, N Tian

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Kendenggaoer-Kuokuqueke region lies in the western part of Chinese North-western Tianshan. New laser ablation inductively coupled plasma mass spectrometry zircon U-Pb geochronology for five separate granitic plutons for this region reveal two distinct intrusive periods: late Devonian (367~361 Ma) and late Carboniferous (315~301 Ma). These intrusions all share an arc-like geochemical affinity (ie enrichment of large ion lithosphere elements and negative anomalies of Nb, Ta and Ti). In situ zircon Hf isotopic compositions further differentiate the magmatic cycle, with the late Devonian intrusions yielding more depleted eHf(t) (+1.47~+6.54) composition than the late Carboniferous intrusions (eHf(t) = +4.95~+9.79). These geochemical data suggest that they might be mainly derived from different source regions and the tectonic setting was transformed into post-collisional in the late Carboniferous. As in many significant porphyry-ore districts, this dramatic tectonic reconfiguration, combined with melting of an evolved crust, resulted in genesis of metal-bearing melts. Furthermore, we can show that Neoproterozoic mafic juvenile lower crust intruded by mantle-derived melts and/or partial melting of slab material generated hybrid primary magma during subduction of the Palaeo-Junggar oceanic crust in the late Devonian. Whereas underplating of mantle-derived magma contributed more to the Late Carboniferous post-collisional magmatism.CITATION:Tian, N, Wei, J H, Fu, L-B and Tan, J, 2015. Timing and geodynamic setting of the late Palaeozoic polymetallic mineralisation in Chinese north-western Tianshan – insights from geochronology and petrogenesis of granitoids , in Proceedings PACRIM 2015 Congress, pp 171–174 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

The Waimumu area, 12 km southwest of Gore, is underlain by the Gore Lignite Measures, an early Tertiary fluvial sequence approximately 500 m thick resting on Triassic-Jurassic argillitic basement. The Waimumu Quartz Gravels (Pliocene) have been deposited locally and are in part due to the localised reworking of the Gore Lignite Measures. Structurally the area is dominated by the Dunsdale Fault System, a steeply dipping series of NE trending reverse faults (Isaac and Lindqvist, 1990). The Belle-Brook, Hedgehope and Parker Road sites sampled are adjacent to the downthrown (east) side of the Hedgehope Fault.The authigenic gold-sulphide association at Belle-Brook was discovered in 1987 (Falconer, 1987: Clough and Craw, 1989). Despite a very limited amount of alluvial mining a significant quantity of authigenic marcasite has developed. Authigenic sulphide trace element analysis has shown anomalous amounts of As, Ni, Cr and to a lesser extent Zn, Pb and eu (Table 1). It has been established that the nickel occurs as a colloform banded Ni sulphide, possibly bravoite, within the marcasite (Figures 1 & 2). Arsenic and nickel (re)mobilisation are well documented in the literature. Generally As and heavy metals are mobilised in the groundwater as a result of the oxidation of sulphides (ie as a result of mining). At Belle-Brook it is reasonable to assume the authigenic sulphide trace element composition reflects either localised groundwater contamination or hydrothermal mineralisation. This poster presents some preliminary findings.

Jan 1, 2001

By J Kuva, M Parian, B I. Pålsson

One of the main factors affecting the suitability of an ore for autogenous grinding is the ore’s competency, ie providing enough critical stones for the grinding process. Several experimental test routines exist and are used for assessing the viability of the ore for autogenous grinding. However, very little attention is given to the generation of fatigue in large stones experiencing repeated shocks in the mill. To investigate this, large pebbles sampled from an industrial autogenous grinding mill running hard and soft ores were categorised based on the grinding energy. From the pebbles, small drill core samples were prepared and went through a series of fatigue cycle tests. Both hard and soft ores showed similar average resistance to failure in compression tests, but the hard ore had a consistent resistance with lower variations. The cores were scanned by XCT before and in-between fatigue tests at the highest reachable resolution, 1.5 µm voxel size. The outcome showed that a higher number of micro-cracks were visible in the soft ore compared to the hard ore. The frequency of micro-crack development in the soft ore may be the reason for its lower specific grinding energy compared to the hard ore. It is obvious that for realistic conditions in an autogenous grinding mill, stones are pre-weakened by fatigue before they fracture. Therefore, shortcut methods focusing only on running tests on fresh and small samples may operate in unrealistic conditions by ignoring the fatigue phenomenon. This is even more important for ores that are on the borderline to be considered as competent for autogenous milling.

Aug 24, 2022

By C MacDonald

There are many technologies available today in terms of fire and life safety in road tunnels. So many in fact that it is becoming more and more difficult for clients and contractors alike to determine what they want and what they need. From a clientÆs perspective, fire and life safety is about protection to its infrastructure and to the public at large. Conversely, the contractor is looking to meet its æfit for purposeÆ or ædeem to complyÆ requirements in the most economic and practicable way. Practices regarding fire and life safety in road tunnels have undergone a degree of transformation during the last decade or more throughout the world. This transformation has largely been driven by a series of catastrophic accidents such as the major fires in Europe including the Mont Blanc Tunnel, Tauern Tunnel, Saint-Gothard Tunnel, and now most recently in the CityLink Tunnels in Melbourne. International guidelines produced by organisations such as the Permanent International Association of Road Congresses (PIARC), the European Union, the International Tunnelling Association (ITA) and the US National Fire Protection Authority (NFPA) now provide clients, owners and designers with the tools required to define and specify the required fire and life safety systems in road tunnels. The majority of these tools are based on risk assessment and risk management. Recent road tunnel projects within Australia, however, have not referred solely to such guidelines. Clients have opted to prescribe different or additional fire and life safety requirements within the projectÆs technical specification documentation (project requirements), leaving designers and contractors with little room to implement alternatives or substitutions. Further, these project requirements are largely dictated by practice established on previous road tunnel projects within Australia. This paper looks at the current international guidelines and practices and undertakes a comparison with the EastLink tunnels in Melbourne and other road tunnels within Australia and makes assessment on whether Australian methods are the most appropriate for clients and contractors alike. Focus is directed to the key elements of fire and life safety such as:traffic envelope, barrier arrangements and emergency walkway provisions;deluge systems;drainage systems;fire rating requirements;tunnel ventilation systems;cross passage provisions;fire safety assessment;critical intelligence systems including help phones, CCTV, incident detection, tunnel signage, etc; andexternal tunnel control systems.

Jan 1, 2008

At the Orieco mine quartz veins carrying sulphides were localized in parts of an extensive fault zone in the Mathinna Beds during late Middle Palaeozoic mineralization.These deposits were subsequently exposed, and oxidation of the sulphides by percolating groundwaters resulted in the formation of gossans at the surface, and replacement close to the permanent water table of the more soluble sulphides by copper sulphides (chalcocite, coveIlite). A restricted zone containing copper oxides (cuprite, tenorite), copper carbonates (malachite, azurite), iron arsenates (scorodite, pharmacosiderite) and possibly rare copper sulphates occurred above the water table.The renewed oxidation of these deposits following mine development has been facilitated by the ready circulation of air and water combined with the formation of large free surfaces ideal for evaporation of aqueous solutions. Under these new conditions of high initial sulphate concentration, low pH, and relatively high Eh, the previously formed mineral assemblage is unstable and numerous Cu (Fe,Zn)-sulphates and Fe (Cu,Pb)-arsenates are presently forming in fractures in the fault zone and on the adit and stope surfaces for some considerable distance from the Sulphide-rich ore shoots. The observed spatial sequence of the major sulphates with respect to the sulphide-rich zones (Le. chalcanthite-antleritebrochantite and langite) is consistent with decreasing sulphate concentration and increasing pH away from the oxidizing sulphides.

Jan 1, 1970

By B Mack

The cost of water treatment is now more than ever a major consideration for maintaining an environmentally and economically sustainable mining operation. As an industry, we often have to consider water sources that are highly impure and difficult to treat. We are also discovering the value of our waste waters in this regard and using new and improved methods and technology to reclaim and reuse water. In many instances, the water or waste water to be treated is highly acidic and saturated in sparingly soluble salts. Conventional systems used to liberate this type of water typically involve high doses of lime with large volumes of waste sludge produced, and are comparatively complex to operate, to pretreat the water in order to reduce scaling tendency on the reverse osmosis stage. However, if the water is considered valuable for reuse, then why not avoid difficult and cumbersome pretreatment processes and treat the water at low pH to keep the sparingly soluble salts, metals and other dissolved species in solution. This paper describes a patented technology that uses and successfully proves this concept as a cost effective option for certain situations. Results from a treatability study on an Australian groundwater are discussed, along with an economic comparison to a conventional method and discussion on full-scale potential.

Jan 1, 2009

By Parker A. J, Muir D. M

Solutions of acetonitrile in water dissolve water soluble copper(I) chloride. Removal of volatile acetonitrile from the resulting solutions, by distillation with low grade steam, precipitates pure copper(I) chloride. This is used to purify a crude copper chloride sublimate from the chlorination of nickel matte but is applicable to other sources of copper(I) chloride. The pure product can be converted to pure copper(I) oxide, copper(II) oxychloride or pure copper metal directly.

Jan 1, 1980

A fundamental component of grade control at Tarmoola Mine has been the monitoring of assaying through quality assurance programs. The programs have concentrated on issues related to accuracy and precision of leachwell and fire assay techniques, sample preparation and grade variability within a sample. An outcome of monitoring has been identification of shortcomings in the application of assaying techniques to Tarmoola ore types that contain coarse particulate gold. Leachwell has shown satisfactory precision since introduction as the primary assay technique in October 1998 but leachwell accuracy and recovery through comparison with fire assay techniques has identified bias. A bias toward higher fire assays in grades above 2 g/t invoked an investigation into the cause of the discrepancy between leachwell and fire assay. Testwork evaluated Leachwell assay recovery by varying leach time duration, which showed that by increasing the leach time improved recovery significantly. Monitoring of leachwell against fire assay had shown that a leachwell (200 g) with a one hour leach has under-called grade when compared with fire assay by up to 18 per cent, on average, for Tarmoola ore types. Alternatively, optimisation of the leachwell assaying technique using a 200 g pulp and a two hour leach has returned, on average, higher assays than fire assay by up to eight per cent. Testwork on screen fire assays, duplicate assays and fire assay to extinction has demonstrated assay variability associated with coarse, particulate gold. The variability and distribution of gold in Tarmoola ore types has emphasised the importance of high quality sample preparation for leachwell assaying to ensure liberation of gold to leaching solutions. Assay quality assurance protocols are vital to assay data integrity and enable confidence in delineation of ore-waste boundaries and provide early recognition of problematic assaying periods and isolation of grade control practices, which depart from performance standards critical to the operation.

Jan 1, 2000

By T Baumgartl, D R. Mulligan, D Doley, A Schneider

In arid and semi-arid areas evapotranspiration (ET) cover systems are often used to mitigate contaminated seepage from hazardous mine waste into the adjacent environment. The theory of ET covers is based on the water balance equation with the aim of minimising seepage. While cover systems are commonly trialled, the influences of variability in climate and cover structure on water balance equation parameters are seldom investigated.Water balance equation parameters and their variability were analysed for two ET cover trials constructed from benign waste rock in semi-arid Australia. Seasonal and inter-annual variations in rainfall critically influence cover performance. For successful cover system operation, the average return periods for higher than average rainfall should be taken into account. In addition, failure of ET covers has a higher probability in areas with marked rainfall seasonality. Water holding capacity and plant available water content are low in covers constructed from waste rock. Changes in water holding capacity due to variation in particle size distribution are likely and critically influence cover performance. The application of topsoil can be beneficial for water ingress control through run-off, but a balance has to be struck between run-off, erosion and plant available water. Changes in vegetation composition only influence evapotranspiration water losses at plant coverage exceeding 50 per cent, which is unrealistic in semi-arid areas. This study showed that the capacity of ET cover systems to hold and dispose of received rainfall is often lower than assumed by industry practitioners. Furthermore, in order to improve reliability of long term cover performance, the variability of rainfall and water holding capacity of the cover has to be included in water balance models.CITATION:Schneider, A, Baumgartl, T, Doley, D and Mulligan, D R, 2012. Variability in parameters of the water balance equation and their influence on evapotranspiration cover performance, in Proceedings Life-of-Mine 2012 , pp 293-300 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

Triboelectric Separation - Beneficiation of Coal The performance of triboelectric separators is highly sensitive to the selectivity of the particle charging process. This paper presents a quantitative study on triboelectric coal beneficiation. The performance of different charging media was studied. Stainless steel was identified as having a work function between that of coal and silicate gangue and found to be the optimum charging medium for coal beneficiation. Recent results from separation tests were performed where silicate gangue was separated from crude coal using a parallel plate free-fall separator are illustrated.

Sep 13, 2010

Dynamics of Three Phase Contact Line Motion in Liquid-Liquid-Solid Systems - Impact of Surface Roughness

Sep 13, 2010

By A Parbhakar-Fox, S C. Dominy

The prediction of acid and metalliferous drainage (AMD) from mine waste materials is critically important during all stages of the mine value chain. However, to determine such geoenvironmental characteristics static and kinetic testing of individual waste units must be performed on representative samples. The importance of sample selection cannot be underestimated; it is the single most critical aspect of any geoenvironmental investigation. Poor sampling techniques and inadequate sample selection will contribute to excessive variance, difficulties in interpretation and incorrect assessment. By undertaking mesotextural characterisation based on hyperspectral mineralogical data (with sulfur assay data if available), opportunities to improve sampling strategies are presented. Such data will inform the selection of samples for low-cost total sulfur, paste pH and geoenvironmental logging, which collectively will allow for accurate AMD forecasting and improved sampling practices to be achieved. Once sampled, robust quality assurance/quality control (QA/QC) protocols must be developed where the use of international certified reference standards become obligatory. This is currently not practised, resulting in inter-laboratory discrepancies when undertaking waste classification. Further improvements in geoenvironmental characterisation testing lies in the adoption of blended static testing protocols, whereby blends of waste materials can be efficiently tested so as to give an early forecast as to whether they will produce acidic or metal-laden drainage. Such information is integral in developing a waste schedule that will allow for a non-acid forming waste landform to be constructed right from the start of the operational phase. Ultimately, improvements in this discipline lie in technological innovations with regards to mineralogical characterisation, and by offering geoscience and minerals engineering students a competent education in the discipline. Collectively, this will empower a step-change in AMD prediction and waste handling, and will make the realisation of the United Nations Sustainable Development Goals a reality, rather than a dream.CITATION:Parbhakar-Fox, A and Dominy, S C, 2017. Sampling and blending in geoenvironmental campaigns – current practice and future opportunities, in Proceedings Eighth World Conference on Sampling and Blending , pp 45–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

Predicting Flotation Response from Liberation Information

Sep 13, 2010

Alkaline leaching with sodium carbonate solution adjusted to pH 9·5 to 10·0 preferentially dissolves thorium from a mixture of rare earth and thorium hydroxides. Rare earth sodium carbonates form in the alkaline leaching stage.These are converted to rare earth oxides for use as optical and ophthalmic polishing agents. Quadrivalent cerium is extracted under similar alkaline leaching conditions.INTRODUCTIONAustralia has made significant contributions to mineral chemistry and mineral dressing. As often happens with an industrially immature country, research investigations often outstrip the ability or desire of commerce to exploit them. It is wrong to think exclusively in terms of export of raw materials. Imagination assists in developing world trends. The chemical utilization of mineral sands has interested a group of investigators, chiefly at the Commonwealth Scientific and Industrial Research Organization (C.S.I.R.O.) and, more recently, in the mining industry itself. From an international point of view the highlight of this work was Newnham's (1960) process for the separation of hafnium from zirconium. Earlier work at C.S.I.R.O. investigated the chlorination of rutile, zircon, and monazite. Assuming that titanium tetrachloride would be available in large quantities in the post war years, extensive work was done by Kraitzer, McTaggart, and Winter (1948) on organic compounds of titanium. This work led to the development of heat resistant paints, plastic compositions, and improved organic protective coatings that predated overseas work by up to seven years. (Post, Shiihara and Schwartz, 1961; Anon, 1955). Contributions were made to the production of refractory hard metals (Kraitzer, 1949; Kraitzer and Newnham, 1956). Pilkington and Wylie (1947) and Urie (1947) investigated the production of rare earths from monazite by an acid process.

Jan 1, 1963

By A Asadov, D Nair

This paper discusses the determination of the percentage of crystalline material in a natural silica deposit which would be considered harmful to health (<10 ¦m). A sample of the natural silica material was recovered and split into a number of subsamples. Samples were sieved using a conventional dry sieve to remove material >300 ¦m before testing. Particle size analyses of the fine fraction showed 75 per cent of the material was below 10 ¦m. Initially XRD and XPS were run on the samples to determine the minerals and composition of the sample. The XRD revealed strong quartz peaks and smaller tridymite peaks with a high amorphous background. The XPS indicated traces of iron, titanium and carbon with dominant silicon and oxygen peaks. The structure of the sample was investigated using the SEM. It was apparent that there were a number of larger quartz crystals (>30 ¦m) with a mix of amorphous and crystalline in the finer fraction. It was also observed that amorphous material was attached to the surface of the crystals. In order to determine the percentage of crystalline quartz a known amount of quartz was added to the sample incrementally. On each addition an XRD scan was performed and the area under the peaks recorded. Back analysis of these peaks with an assumed percentage of crystalline material in the original sample gave a crystalline content of 30 per cent. The quantity at the respirable fraction was estimated to be 18.7 per cent.

Jan 1, 2003

THE object that the writer has mainly in view in presenting this paper is to draw the attention of those connected with the technical side of the industry to the unsatisfactory and by no means up-to-date methods employed in estimating the tin contents of an ore. At the same time, what is regarded, from the writer's personal experience, as a satisfactory and reliable method is explained in detail. It is a curious fact that for the last 25 years tin·assay methods have made little or no advance, while those now in general use ill connection with copper and lead ores can scarcely be compared with those then obtaining, so greatly have they been improved upon. Though it. is not altogether expected that the method herein advocated will at once meet with general approval, the writer hopes the resultant discussion may bring out points that have hitherto escaped detection.FIRE METHODSThe old Cornish method of smelting with anthracite is now obsolete. The cyanide assay, although unreliable, is still much used because of its simplicity. In the Malaya many buyers of tin ores use the cyanide assay, the smelting being carried out generally in a benzine furnace. It is essential that the smelting with cyanide be performed at a low temperature. Even then, impurities, such as Sb2S3 and...

Jan 1, 1912

By W Farnworth

The Huntly West Mine has undergone significant changes in the last two years, which will affect the remainder of the mine's life. The paper describes the evolvement of plans and an overview of the technical considerations made in planning for and implementing the first New Zealand longwall operation. The technical investigations involve the longwall equipment, exploration, ventilation and strata control. The focus on these areas was to ensure that unacceptable project risks were addressed. Implementation of longwall mining at West Mine is planned in three phases, Development, Panel One extraction trial, and Full Longwall operation.   At present the development phase is complete, longwall installation is in progress and production start-up is planned for the end of August, 1991.

Jan 1, 1991

Mining is both a high risk and a long term business. This is dramatically illustrated by the fact that, on average, the explorer will expend over $30 million in a ten year period for each significant economic discovery. The time required to complete the exploration process is one of the most substantial commitments made by any mining company. For example the time lag between the implementation of an exploration programme and an economic discovery is variously estimated to take two to ten years. The ore definition phase following discovery currently takes between two and five years while subsequent mine development may take one to two years in easy situations and up to 8 in difficult environments. In most countries the critical path through the early stages is determined largely by technical considerations but in almost all countries the path through the later phases is dictated by the plethora of permits, licences and community involvement steps.

Jan 1, 1982