Search Documents

By K. E. Brown, A. R. Hagedorn

Continuous, two phase flow tests have been conducted during which four liquids of widely differing viscosities were produced by means of air-lift through 1%-in. tubing in a 1,500-ft. experimental well. The purpose of these tests was to determine the effect of liquid viscosity on two-phase flowing pressure gradients. The experimental test well was equipped with two gas-lift valves and four Maihak electronic pressure transmitters as well as instruments to accurately measure the liquid production, air injection rate, temperatures, and surface pressures. The tests were conducted for liquid flow rates ranging from 30 to 1,680 BID at gas-liquid ratios from 0 to 3,-270 scf/bbl. From these data, accurate pressure-depth traverses have been constructed for a wide range of test conditions. As a result of these tests, it is concluded that viscous effects are negligible for liquid viscosities less than 12 cp, but must be taken into account when the liquid viscosity is greater than this value. A correlation based on the method proposed by Poettmann and Carpenter and extended by Fan-cher and Brown has been developed for 1¼-in. tubing, which accounts for the effects of liquid viscosity where these effects are important. INTRODUCTION Numerous attempts have been made to determine the effect of viscosity in two-phase vertical flow. Previous attempts have all utilized laboratory experimeneal models of relatively short length. One of the initial investigators of viscous effects was Uren1 with later work being done by Moore et al.2,3 and more recently by Ros.4 However, the present investigation represents the fist attempt to study the influence of liquid viscosity on the pressure gradients occurring in two-phase vertical flow through a 1¼-in., 1,500 ft vertical tube. The approach of some authors has been to assume that all vertical two-phase flow occurs in a highly turbulent manner with the result that viscous effects are negligible. This has been a logical approach since most practical oil-well flow problems have liquid flow rates and gas-liquid ratios of such magnitudes that both phases will be in turbulent flow. It has also been noted, however, that in cases where this assumption has been made, serious discrepancies occur when the resulting correlation is applied to low production wells or wells producing very viscous crudes. Both conditions suggest that perhaps viscous effects may be the cause of these discrepancies. In the first case, the increased energy losses may be due to increased slippage between the gas and liquid phases as the liquid viscosity increases. This is contrary to what one might expect from Stokes law of friction,' but the same observations were made by ROS4 who attributed this behavior to the velocity distribution in the liquid as affected by the presence of the pipe wall. In the second case, the increased energy losses may be due to increased friction within the liquid itself as a result of the higher viscosities. The problem of determining the li- quid viscosity at which viscous effects becomes significant is a difficult one. Ros4 has indicated that liquid viscosity has no noticeable effect on the pressure gradient so long as it remains less than 6 cstk. Our tests have shown that viscous effects are practically negligible for liquid viscosities less than approximately 12 cp. Actually there is no single viscosity at which these effects become important. These effects are not only a function of the viscosities of the liquids and of the gas but are also a function of the velocities of the two phases. The velocities in turn are a function of the in situ gas-liquid ratio and liquid flow rate. Furthermore, the role of fluid viscosities in either slippage or friction losses will depend on the mechanism of flow of the gas and liquid, i.e., whether the flow is annular. as a mist, or as bubbles of gas through the liquid. These mechanisms are also a function of the in situ gas-liquid ratios and the flow rates. It would thus seem that the best one could hope for is to determine a transition region wherein the viscous effects may become significant for gas-liquid ratios and liquid production rates normally encountered in the field. The viscous effects might then be neglected for liquid viscosities less than those in the transition region but would have to be taken into account when higher viscosities are encountered. There are numerous instances where crude oils of high viscosity must be produced. The purpose of this study has been to evaluate the effects of liquid viscosities on twephase vertical flow by producing four liquids of widely differing viscosities through a 1 % -in. tube by means of air-lift. The approach used in this study was as follows:

Jan 1, 1965

By C. A. Winkler, V. Hospadaruk

PREVIOUS papers from this laboratory have discussed the effect of chloride ion on the cathode polarization during electrodeposition of copper from copper sulphate-sulphuric acid electrolytes, in the presence and absence of gelatin. The steady state polarization'" was found to decrease sharply and pass through a minimum with increasing chloride ion concentration in the presence of gelatin. The minimum shifted to higher chloride ion concentrations and to higher polarization values with increase in current density or gelatin concentration, while an increase of temperature shifted the minimum toward lower halide concentrations and lower polarizations. Since these observations were made in acid-copper sulphate electrolytes that contained no other addend than gelatin, there was obviously the possibility that they were not applicable to deposition of copper from commercial electrolytes that contain a variety of other substances in relatively small amounts. In particular, it was of interest to determine whether the presence of arsenic, antimony, or bismuth in the electrolyte would materially alter the behavior. Experiments have now been made under a variety of conditions with systems containing these cations, and the results are summarized in the present paper. Experimental Polarization measurements were made at 24.5oC in a Haring cell in the manner described previously.' Electrolytes were made with doubly-distilled water, and contained 125 g per liter of copper sulphate and 100 g per liter sulphuric acid, both of reagent grade Eimer and Amend gelatin from a single stock was used throughout. Chloride ion was introduced as reagent grade sodium chloride, and arsenic, antimony, and bismuth by dissolving the chemically pure metal in hot concentrated sulphuric acid and adding appropriate amounts of the solutions to the electrolyte. Each cathode, of 1/16-in. thick rolled copper, was first etched in 40 pct nitric acid and washed thoroughly with distilled water. The surface was then brought to a standard condition4~9 by electrodeposition from an acid-copper sulphate electrolyte containing no gelatin, at a current density of 3 amp per sq dm for 30 min, followed by deposition at a current density of 2 amp per sq dm for l hr. As in previous studies, the cathode polarization eventually attained a steady-state value (15 to 75 min) such that further change in polarization did not exceed 0.2 mv per min. The polarization values recorded are those for the steady states. "Excess weights" were determined with arsenic and antimony present in the electrolyte, as the difference between the weights of the deposits obtained in the presence of these cations and those obtained in their absence, with the two cells connected in series. When gelatin was present along with the arsenic or antimony, it was also added to the electrolyte in the cell in series. Results and Discussion The results of the study are summarized in Figs. 1 to 6. From Fig. 1, top, it is evident that the presence of arsenic or antimony alone results in an increase of polarization, while bismuth alone causes a decrease. The presence of gelatin (25 mg per liter) rather drastically modifies all three cation effects, as indicated in the lower panels of the same figure. The addition of chloride ion, when no gelatin is present, causes comparable decreases in polarization in the presence of antimony and bismuth, but a relatively larger decrease when the electrolyte contains arsenic. It is interesting to note that the decrease in polarization brought about by addition of chloride when both arsenic and antimony are present parallels the behavior with arsenic alone, while the polarization in the electrolyte containing the cation mixture, without chloride added, corresponds to that for an electrolyte containing only the antimony cation. Similarly, the polarization at zero concentration of chloride in electrolyte containing arsenic and bismuth is that corresponding to an electrolyte containing arsenic alone. From Figs. 3a, 4a and 4b, it is clear that, in the presence of gelatin at a level of 25 mg per liter, the effect of chloride in the presence of arsenic and antimony, or a mixture of the two, becomes quite analogous to that observed in the absence of added cations. When both bismuth and gelatin are present (Fig. 5), the decrease in polarization with increased chloride concentration is virtually absent. This is perhaps a reflection of the large decrease in polarization brought about by the bismuth itself in the presence of gelatin. The shifts of the minimum in the polarization-chloride concentration curves brought about by changes of temperature (Fig. 3b), gelatin concentration (Figs. 3c and 4c) and current density (Fig. 3d) when the metal cations were present are all similar to the corresponding shifts observed in their absence." The approximately linear "excess weightv-anti-mony concentration relation recorded in Fig. 6 would seem to indicate that antimony is codeposited with copper to a considerable extent. On the other hand, only very limited amounts of arsenic appear to be adsorbed or codeposited.

Jan 1, 1954

By J. Chipman, N. J. Grant, H. L. Bishop, H. N. Lander

Data of several studies on the equilibrium between molten iron and open hearth-type slags have been combined to determine some of the chemical reactions involved in steel-making. Effects of slag composition and temperature on the iron oxide activity, distribution of sulfur between slag and metal, and the carbon content of the metal are discussed. Also, an overall reaction for the equilibrium between sulfur and oxygen is presented. DURING the past 15 years, a number of significant equilibrium studies have been carried out between liquid iron and simple basic and acid slags in an effort to throw light on the chemical reactions involved in steelmaking. This paper is a summary of the experimental reports on investigations which have been conducted at the Massachusetts Institute of Technology, and of related work in other laboratories. The investigations summarized in this paper include the works of Fetters and Chipman1 and Taylor and Chipman,' which dealt with simple slags that are similar to those found in the open hearth. The sulfur determinations of the slag-metal tests of Fetters and Chipman as reported by Grant and Chip-man" are included. Also, the investigations by Win-kler and Chipman' and Grant and ChipmanQ f more complex slag systems are included in this summary. The experimental procedure is described in detail in each of these papers and will not be discussed. Since the previous reports have been somewhat independent, it is desirable to review and combine the data of the various investigations to determine, as accurately as possible, the reactions in the slag-metal systems of the open hearth. It is the object of this report to present the combined data in such a way as to enhance their utility and applicability. Oxidizing Power of Slags of the System (CaO+MgO)-Si0,-FeO in Equilibrium with Carbon-Free lron The slags selected to determine the iron oxide activity in equilibrium with pure liquid iron were those containing less than 2 pct each of P,O,, MnO, or A1,0, on a weight percentage basis. The method used to calculate activities of iron oxide in liquid slags was that developed by Taylor and Chipman.' The solubility of oxygen in molten carbon-free iron under pure iron oxide slags can be expressed by the following eauation —6320 log (pctO)-------------— + 2.734 [1] where T is the absolute temperature. The oxygen solubility values as determined from Eq. 1 were used throughout this study to calculate the iron oxide activity. The iron oxide activities of slags of various iron oxide contents are plotted in Fig. 1 as a function of the basicity, which is defined as the ratio (pct CaO + pct MgO)/pct SiO,, and are based on molecular percentage values of the components. The percent (FeO), is the total iron content in the slag calculated to FeO. Fig. 1 shows that as the basicity increases at constant mol pct (FeO),, the iron oxide activity increases rapidly and reaches a plateau which extends on the basicity scale from about 1.3 to 2.3; the iron oxide activity then decreases rapidly until a basicity of about 3.0 is reached, where it tends to level off. The solid portions of the curves represent the experimental data of Fetters and Chipman and Win-kler and Chipman. Their experimental heats were made in magnesia crucibles, and hence the slags were saturated with magnesia. The broken lines on the left represent the experimental data of Taylor and Chipman, who used a rotating crucible. In general, these slags contained less than 3 pct MgO. The absence of data for slags containing less than about 40 mol pct (FeO), and basicity ratios greater than about 2.5 made it necessary to calculate curves using ionic concepts of slags. The broken lines on the right, which disregard the solubility limits of di and tricalcium silicate and lime, were obtained by following the treatment of Flood and Grjotheim,"

Jan 1, 1957

By W. D. Forgeng, R. L. Folkman, D. C. Hilty

The solubility of oxygen in molten Fe-Cr alloys has been determined at 1550° , 1600°, and 1650°C for alloys containing up to alloyshasbeenabout 50 pct Cr and found to decrease as chromium increases to 6 pet and then to increase gradually. Phase relations in the Fe-Cr-0 system at steelmaking temperatures have been evaluated and two previously unreported oxides have been identified. OPERATIONS in the melting and refining of chromium steels are dependent to a major degree on the reactions of chromium and iron with oxygen and are primarily directed toward controlling and modifying these reactions to secure maximum advantage in the utilization of chromium. Although fairly effective practices have been developed empirically, understanding of the specific reactions is limited. Moreover, the ability of molten steel to dissolve oxygen that subsequently precipitates as oxide inclusions during solidification is well known, so that clarification of the effect of chromium on the nature and mechanism of formation of these inclusions is desirable. Study of the problem indicated that increased knowledge of the fundamental Fe-Cr-0 system is essential to further technical and economic improvement. Consequently, an investigation of the influence of chromium on the solubility of oxygen in molten iron and of phases and phase relations in the Fe-Cr-0 system was undertaken at the Metals Research Laboratories of the Electro Metallurgical Co. as part of a general program on the effective utilization of chromium in chromium steel production. Experimental Procedure All of the experimental runs made during this investigation were carried out in the rotating crucible induction furnace which has been described in detail in a previous publication.' In review, the principle underlying this furnace is that rotational forces in the crucible cause the molten metal to assume a concave shape in such a manner that the slag is contained in the molten metal cup, thereby minimizing slag/crucible contact and subsequent reaction. Practically all of the heats were melted in commercial-quality magnesia crucibles of the type usually furnished for laboratory induction furnaces. All of the runs were made under an argon atmosphere after the furnace chamber had been degassed. Bath temperatures were controlled by Pt—Pt-10 pct Rh thermocouples. The basic furnace charge consisted of a premelted 12 to 15 lb electrolytic iron slug which had been cast to a shape convenient for fitting into the rotating furnace crucible. A typical analysis of the electrolytic iron slugs is given in Table I. For certain runs, it was desirable to melt down charges containing high initial chromium contents. In these cases the chromium was added to the electrolytic iron during the premelting operations. Chromium was added to the rotating furnace bath in the form of electrolytic chromium of the analysis given in Table 11. In all of the constant temperature runs, the standard procedure was to melt down the electrolytic iron or alloy slug under vacuum, admit argon to slightly greater than atmospheric pressure, and adjust rotational speed to develop a well formed "cup" on the bath surface. The melt was then saturated with oxygen by an addition of ferric oxide and the temperature of the bath adjusted to within +5°C of the desired level. At this point the heat was permitted to come to equilibrium prior to sampling or further addition. This time interval was varied from 15 min to 2 hr but generally was about 20 min. After sampling, the desired chromium addition was made and the bath again equilibrated prior to subsequent sampling. This cycle of addition and sampling continued for the duration of the run which lasted from 4 to 8 hr. At the end of this period, power was shut off and the bath allowed to solidify in the furnace. Quenched metal samples were taken from the equilibrated melts by means of the "Taylor sampler" which has been described by Taylor and Chipman.' Before being submitted to chemical analysis, all samples were carefully examined for surface slag occlusions and cold shuts. Later in the study, each sample was radiographed and examined metal-lographically in cross-section to determine the presence of internal defects. On the basis of these examinations, sound and apparently clean specimens were selected from the Taylor samples for chemical analysis.

Jan 1, 1956

By W. C. Winegard, J. R. Carruthers, A. Plumtree, L. R. Morris

The unidirectional solidification of dendrites containing central twin planes was studied in A1-Ti alloys. Once nucleated, the twinned dendrites are a Twore ejficient form for solute redistribution and therefore grow in preference to the normal columnar dendvites. Comparison of these twinned dendrites to adjacent colunmar dendrites by means of decanting experinzents and electron-probe rnicvoarmlysis indicates that these special dendrites grow with less undercooling than normal dendrites. These findings are further supported by the effect of forced convection on the dendrite morphologies. COMMERCIAL semicontinuous cast ingots of most aluminum alloys frequently exhibit large grains which appear to be composed of hundreds of parallel, continuous, thin lamellae. This structure has been termed "basaltic",' "fiederkristall", or, commonly, "feathery grain". The lamellae are 'about 100 p thick, several inches long, and each lamella contains a central (111) coherent twin boundary. The feathery grain has been reported to have a (112) direction2 and a (110) direction4 in the twin plane parallel to the casting direction, in contrast with the usual columnar structure where a (100) direction predominates. Aust et uZ.~ proposed that the twin boundaries were growth twins nucleated by stacking faults on the octahedral planes. chalmers6 has suggested that feathery grain may grow by a re-entrant edge mechanism, as proposed by wagner7 for twinned dendritic growth in germanium. Cahn et ~1.~ have concluded that the occurrence of feathery grain is evidence of some form of lateral layer growth rather than the atomically continuous growth normally observed in metals. The postulates by Chalmers and Cahn would seem to be contradicted by the work of Nakao~"' who showed that feathery grain only occurs when growth rates are high and the aluminum contains some solute. Specifically, Nakao found that in order to obtain feathery grain, in small castings solidified unidirec-tionally upward, the rate of growth must be above 2.4 cm per min and a critical solute concentration must be present. Below this solute concentration the grain structure was totally columnar. The critical solute concentration was found to be approximately: 0.04 wt pct Ti, 2 wt pct Cu or Mg, and 8 wt pct Zn. As pointed out by Chalmers it is not obvious why a twin-plane re-entrant edge mechanism would occur in aluminum which is thought to have a diffuse solid-liquid interface. The present experiments were undertaken to determine the growth mechanisms in- volved and to study the solute segregation in more detail. EXPERIMENTAL PROCEDURES Alloys ranging in composition from 0.05 to 0.23 wt pct Ti* were prepared from 99.9 pct pure Ti and 99.993 pct pure Al. Two-hundred-gram samples of A1-Ti binary alloys were solidified unidirectionally and vertically upward from a water-cooled copper base, in a heated insulated mold. The 1-in.-diam, 6-in.-length mold was made of Marinite (manufactured by Johns-Manville Co.). The mold was attached to a 24-in. pivoted arm such that by dropping a weight the mold was rotated 180 deg, throwing the liquid metal from the solid. In this way, the solid-liquid interface was revealed by decanting. A sketch of the decanting mold is shown in Fig. 1. The alloy was poured into the mold at temperatures ranging from 680" to 750°C, partially solidified by water cooling from the base, and decanted after a measured time interval. Growth rates for each metal-pouring temperature were calculated from solidification-time vs length solidified curves. Temperature gradients in the melt were measured using four No. 34 gage thermocouples which protruded into the mold cavity. Grain orientations were determined by X-ray diffraction using Laue back-reflection techniques. Grain substructures were examined metallographically, using polarized light, by applying a thin epitaxial anodic film to polished sections after the method of Hone and pearson." Titanium micro segregation was measured by electron-probe microanalysis using a NORELCO AMR/~ with a mica crystal and proportional-flow counter. Several of the cast samples exhibited feathery and columnar dendrites growing in the same direction and

Jan 1, 1967

By John C. Calhoun, R. C. Newman

A report is made of experimental work performed on the capillary retention of water within porous solid systems, the displacement being accomplished with air and various organic liquids. A portion of the experiments were designed to measure the lowering of vapor pressure of water within a porous solid with subsequent conversion of such vapor pressure data to capillary pressure values. The form of the capillary pressure curve at high capillary pressures has been elucidated from this data. Certain theoretical approaches are presented to indicate the correlation between work done by previous investigators. The present work is correlated also with theory. Surface area values are calculated for the various core systems studied. INTRODUCTION Leverettl in 1941 presented a paper which gave the essential concepts of capillary behavior in porous solids. His presentation included both theoretical and experimental aspects of the problem. He defined the term "capillary pressure" and applied it to an ideal porous system. His work included the definition of a dimensionless quantity which was a function of fluid saturation and which could be correlated with porosity and permeability for clean, unconsolidated sands. His experimental work was performed by the drainage of water from packed columns of unconsolidated sands. Subsequently, other authors have presented experimental techniques which permit the determination of capillary pressure data on small core samples. Data have been presented on porous systems other than unconsolidated sand and with the use of liquids other than water. Notable among these are the works of Hassler, Brunner and Deahl,2 Bruce and Welge,³ Amyx and Yuster, and Purcell. Others have indicated the applicability of such data to field problems without regard to the theoretical aspects of the capillary pressure saturation function. Within the recent published literature there have also been reported studies of the correlations between capillary pressure data and other fundamental properties of porous solids. It was the intent of the present reported work to investigate the behavior noted by water and various other liquids within porous systems in an attempt to amplify existing correlations between capillary properties, surface properties, and other fundamental characteristics of porous systems. The experimental work described here was performed as two different investigations but due to its nature it is reported as separate phases of the same general topic. CAPILLARY PRESSURE AND VAPOR PRESSURE LOWERING It has long been recognized that the vapor pressure above the curved surface of a liquid is a function of the curvature of the liquid surface." The capillary pressure is also a function of the curvature of the liquid surface. Both capillary pressure values and vapor pressure lowering are, therefore, functions of the liquid saturation of a porous solid. A quantitative relationship between the vapor pressure lowering and the capillary pressure can be simply developed by considering a porous solid system containing water in equilibrium with its vapor. The capillary pressure at any height within the system is defined as Pc= Pv -P1.......(1) where PI is the pressure in the vapor phase and PI is the pressure in the liquid phase. Consider that both the water and its vapor are continuous phases within the system and that at any point the two phases are in equilibrium. The gradients in the liquid and vapor columns within the porous system are: PI = plgdh dPv = pvgdh By integrating these gradients from the point where h = 0 to the height h, values of PI and PI at the point h are found. Let the point where h = 0 be that where Pc = 0. At this point also Pv is equal to Pve, the equilibrium vapor pressure of the liquid above a flat surface. From the first of these integrations since p is independent of height: P = p1gh + P, From the second, by substituting pv = PvM/RT, where M is the molecular RT weight: Pv M Pvo- RT gh By combining the two last equations to eliminate h, one obtains: P1 RT Pv Substituting, values for Pv and Pi in equation (1) gives PyRT RT Pv which is approximately Pc=RT/Mp1 In Pvo/Pv .......(2) This equation relates the vapor pressure above a curved surface with the capillary pressure across the curved surface in terms of measurable quantities. The equivalent of this equation is given by Freundlich."

Jan 1, 1949

By John C. Calhoun, R. C. Newman

A report is made of experimental work performed on the capillary retention of water within porous solid systems, the displacement being accomplished with air and various organic liquids. A portion of the experiments were designed to measure the lowering of vapor pressure of water within a porous solid with subsequent conversion of such vapor pressure data to capillary pressure values. The form of the capillary pressure curve at high capillary pressures has been elucidated from this data. Certain theoretical approaches are presented to indicate the correlation between work done by previous investigators. The present work is correlated also with theory. Surface area values are calculated for the various core systems studied. INTRODUCTION Leverettl in 1941 presented a paper which gave the essential concepts of capillary behavior in porous solids. His presentation included both theoretical and experimental aspects of the problem. He defined the term "capillary pressure" and applied it to an ideal porous system. His work included the definition of a dimensionless quantity which was a function of fluid saturation and which could be correlated with porosity and permeability for clean, unconsolidated sands. His experimental work was performed by the drainage of water from packed columns of unconsolidated sands. Subsequently, other authors have presented experimental techniques which permit the determination of capillary pressure data on small core samples. Data have been presented on porous systems other than unconsolidated sand and with the use of liquids other than water. Notable among these are the works of Hassler, Brunner and Deahl,2 Bruce and Welge,³ Amyx and Yuster, and Purcell. Others have indicated the applicability of such data to field problems without regard to the theoretical aspects of the capillary pressure saturation function. Within the recent published literature there have also been reported studies of the correlations between capillary pressure data and other fundamental properties of porous solids. It was the intent of the present reported work to investigate the behavior noted by water and various other liquids within porous systems in an attempt to amplify existing correlations between capillary properties, surface properties, and other fundamental characteristics of porous systems. The experimental work described here was performed as two different investigations but due to its nature it is reported as separate phases of the same general topic. CAPILLARY PRESSURE AND VAPOR PRESSURE LOWERING It has long been recognized that the vapor pressure above the curved surface of a liquid is a function of the curvature of the liquid surface." The capillary pressure is also a function of the curvature of the liquid surface. Both capillary pressure values and vapor pressure lowering are, therefore, functions of the liquid saturation of a porous solid. A quantitative relationship between the vapor pressure lowering and the capillary pressure can be simply developed by considering a porous solid system containing water in equilibrium with its vapor. The capillary pressure at any height within the system is defined as Pc= Pv -P1.......(1) where PI is the pressure in the vapor phase and PI is the pressure in the liquid phase. Consider that both the water and its vapor are continuous phases within the system and that at any point the two phases are in equilibrium. The gradients in the liquid and vapor columns within the porous system are: PI = plgdh dPv = pvgdh By integrating these gradients from the point where h = 0 to the height h, values of PI and PI at the point h are found. Let the point where h = 0 be that where Pc = 0. At this point also Pv is equal to Pve, the equilibrium vapor pressure of the liquid above a flat surface. From the first of these integrations since p is independent of height: P = p1gh + P, From the second, by substituting pv = PvM/RT, where M is the molecular RT weight: Pv M Pvo- RT gh By combining the two last equations to eliminate h, one obtains: P1 RT Pv Substituting, values for Pv and Pi in equation (1) gives PyRT RT Pv which is approximately Pc=RT/Mp1 In Pvo/Pv .......(2) This equation relates the vapor pressure above a curved surface with the capillary pressure across the curved surface in terms of measurable quantities. The equivalent of this equation is given by Freundlich."

Jan 1, 1949

By A. W. Sommer, H. H. Kellogg

It is shown that SO3-O2 mixtures react with sphalerite at an appreciable rate ill the temperature range of 361° to 527°C to fornz ZnSO4. The rate of reaction follows a parabolle lax. Oxygen, or O2-SO2 mixtures, have a negligible effect on sphalcrite in the same temperatuee range. PRACTICAL roasting of sphalerite is usually performed at 800°C or higher. The calcine is composed of zinc oxide unless the roaster atmosphere contains relatively large amounts of SO2 and the temperature is held to 800oC or lower, in which case zinc sul-fate may also form. Ong, Wadsworth, and assell' have made a careful kinetic study of sphalerite oxidation under these "normal conditions" and have concluded that the rate of the reaction is controlled by the decomposition of an activated complex adsorbed on the sphalerite surface. They found the rate of oxidation to be small at 700°C. Extrapolation of their data to 400°C would indicate an almost negligible rate at this temperature. In our work sphalerite was reacted with air, mixtures of SO2, O2, and N2, and mixtures of SO3, O2, and N2 in the temperature range 361o to 527OC. Negligible rates of oxidation were found, except for the gas mixtures containing SOs. With this latter gas, the oxidation of finely divided sphalerite was fairly rapid and zinc sulfate was the product. Based on the limited evidence available, the rate of sphalerite oxidation by SO3 is postulated to be controlled by gaseous diffusion through pores or cracks in the zinc-sulfate coating. This evidence for the direct reaction of sphalerite and SO, at low temperature may prove of importance to the understanding of zinc-sulfate formation in the dust-collecting equipment usually associated with zinc roasters. The roaster gas carries off fine dust, much of which may be unreacted sphalerite. The temperature in dust-collecting equipment drops from the roaster temperature (about 800°C) through the range of temperature we studied, to ambient temperature. Such dusts are known to contain far larger amounts of zinc sulfate than the primary calcine. It has been assumed in the past that this sulfate is formed by reaction of ZnO dust with SO3 (or SO, plus 0,) in the partly cooled gases. Our work shows that an alternative possibility exists—the direct reaction of SO3 with ZnS dust. EXPERIMENTAL Reaction rates for sphalerite at 350° to 600°C are relatively small so that it was necessary to use finely divided material with a relatively large surface area in order to obtain measureable amounts of reaction. In the preliminary experiments, pure mineral sphalerite, ground to pass a 325-mesh sieve, and chemically precipitated ZnS (in the form of an impalpable powder) were used. In the quantitative rate experiments the ground mineral sphalerite was processed in an Infrasizer to obtain a product with particle size between 9 and 18 µ. The analysis of this material was 66.7 pct Zn, 0.09 pct Fe, and 32.7 pct S (theoretical sphalerite is 67.1 pct Zn, 32.9 pct S). The sized powder was carefully mixed and divided into l-g samples. The apparatus used for the quantitative rate measurements is shown in Fig. 1. For the preliminary experiments the following change was made: The external catalyst furnace (B, C)* was not used. *Letters refer to Fig._______1 .___- Rather, when catalysis of the SO2 + O2 reaction was desired, the glass beads in basket M were replaced by vanadium-oxide pellets. Procedure—A l-g sample of ZnS was placed on a shallow stainless-steel tray, I, and spread evenly to a depth of about 1mm. The tray was placed in the reaction assembly and the assembly inserted in the cold furnace. The furnace tube was flushed with dry argon and then heated to the desired reaction temperature. The temperature was controlled to ±0.5oC. Gas mixtures (O2 + N2 or O2 + SO2) were prepared from tank gases by means of a mixing device identical to that employed by Darken and Gurry.2 The total flow rate of gas was 205 ml per min to point A of Fig. 1. The accuracy of the individual and

Jan 1, 1960

By Walter A. Backofen, Donald H. Avery

Intense primary and cross-slip traces were observed in easy glide on Cu: 6 pct-A1 single crystals deformed in tension. A mechanism of cooperative source operation is developed which recognizes that both the applied stress and that resolved from dislocation arrays contribute to the stress on a source. By considering the stress from arrays, the activation of secondary systems in easy glide and the difference in appearance of slip markings on pure and solid-solution crystals are explained. Furthermore the cross-slip system is predicted to be second favored during easy glide for a large range of orientations. FROM many studies of easy glide in fcc metal crystals, a pattern of observations has developed which still requires full explanation. In pure copper, aluminum, and silver, the easy-glide, slip traces are fine and uniform with steps 50 to 100A on the primary* system.1-4 Yet it has not been at all clear why slip in the pure materials should occur in this way. On the contrary, one might expect, with simple slip and a low hardening rate, that the weakest sources on the primary system would operate extensively to produce strong slip traces. In a brass, however, intense slip steps up to 0.5 are found on both primary and cross-slip system4,6-9 seeger10 has pointed out that in a material of low stacking-fault energy such as a brass, extensive easy-glide cross-slip could not be thermally activated, but rather must originate on the cross-slip plane. In further explanation, the wilsdorfs4 and seeger10 noted that only the cross-slip system would not harden differently than the primary, whatever the latent hardening tendencies of other systems; therefore, in brass, which exhibits high latent hardening, the cross-slip is the only secondary system which could be expected to operate extensively, once it became active. The explanation of how the cross-slip system, on which the applied stress is low, becomes activated has been related, in a nonspecific way, to pileups by Hirsch11 and Honeycombe.l2 In the work to be described, deformation traces on solid-solution Cu: 6 pct A1 single crvstals were studied with conventional light microscopy and a mechanism proposed to explain both the observed activation of secondary systems in easy glide and the difference in appearance of slip markings on pure and solid-solution crystals. EXPERIMENTAL In preparing the Cu-A1 single crystals, rectangular bars approximately 0.4 in. by 0.4 in. by 6 in. were first machined from ingots made by vacuum melting copper of 99.999 pct and aluminum of 99.99 pct purity. They were then packed in powdered graphite and the crystals grown in a modified Bridgman apparatus at a rate of 5 mm per hr under an atmosphere of purified nitrogen. Crystal perfection as indicated by Laue back-reflection spots was good except for the last inch to freeze, which was discarded. Orientations so determined are shown in Fig. 1. Tensile specimens with a reduced gage section were obtained by masking the ends with electrical tape and chemically polishing in a solution of 20 pct HNO3, 24 pct HAc, 52 pct H3PO4, 2 pct Hcl, and 2 pct H20 at room temperature.13 Finally, the specimens were electropolished in a 30 pct ortho-phosphoric acid bath at 12 v. Tensile deformation was performed in an Instron testing machine at a strain rate of approximately 1 pct per min. During easy glide, extensive cross-slip was observed with all crystals, in spite of the low Schmid factor on this system, and in no case was any other secondary trace encountered. A certain sequence of slip-line development was associated with the extension. At yielding, intense primary traces passing completely through the crystal developed at some point on the gage section, generally near the grips; weak cross-slip traces also appeared, extending from the primary traces into the adjacent undeformed crystal, Fig. 2. Further extension led to primary traces adjacent to the first-formed and connecting with those of the cross-

Jan 1, 1963

By H. Sigurdson, T. V. Cherian, C. H. Moore

The phenomenon of recovery of cold-worked metals is interesting not only because of its practical importance but also because of its fundamental significance in solid state reactions. Although extensive investigations1,2 have already been made in an attempt to discover the mechanics of the recovery process, many of the observations have not yet been satisfactorily correlated to provide a completely consistent model for the process. The wide differences in the recovery rates of various properties can be cited as a typical example of one of the difficulties that are encountered. Frequently, for example, the electrical resistance will have almost completely recovered before any recovery in tensile strength can be detected. Of course, such differences in the recovery rates of different properties might be explained by assuming that each property is a unique function of the work-hardened state, and consequently each property exhibits its own unique recovery rate. The assumption that different properties are uniquely related to the work-hardened state cannot be denied. On the other hand, the properties that recover at different rates often exhibit more or less parallel changes upon work-hardening. This suggests that the microstructural changes attending recovery are not exactly the reverse of the changes attending work-hardening. Several types of imperfections must be postulated in order to account for this apparent anomaly. The different recovery rates for various properties, then, are due to the different recovery rales of the type of imperfection to which each property is most sensitive as well as the unique dependence of each property on the cold- worked state. This concept assumes that a simple model of the work-hardened state consisting only of one type of imperfection, such as Taylor's type of dislocation patterns, is inadequate to cope with the diversified phenomena attending work-hardening and recovery. Although current models for the work-hardened state are not useful for describing all aspects of the recovery process, the general trends of the recovery of each postulated type of imperfection as a function of time and temperature should be at least qualitatively deducible from the rather well developed laws of kinetics of reactions in the solid state. Consequently, recovery data might prove useful for elucidating some aspects of the complexities of the work-hardened state of metals. A preliminary attempt to study work-hardening by investigating recovery rates of cold-worked metals is outlined in the following pages of this report. Experimental Procedure Many properties recover when cold-worked metals are annealed below their recrystallization temperature. Therefore, electrical resistivity, thermal electromotive force, X ray diffraction line widths, X ray diffraction line intensities, elastic spring back, density and other physical and chemical properties have been used to study the recovery process. Major interest, however, has generally been directed toward the recovery of the mechanical properties such as hardness, yield strength, and tensile strength. But a search of the literature suggests that the effect of recovery on the true stress-true strain curve has been neglected, in spite of the current recognition of the fundamental importance of such an investigation. An investigation on the effect of recovery treatment on the true stress-true strain curves in tension, therefore, was undertaken in the present study. Commercially pure aluminum (99. + pet Al) in the form of 0.100 in. thick rolled sheet of 2S-O aluminum alloy was selected as the material for this investigation because rather extensive correlatable data are already available on the recovery of some of its properties. Tensile specimens having a 6 in. long gauge section and a uniform reduced section width of 0.500 in. were machined from the sheet in accordance with a design that has previously been reported.3 All specimens were selected with their axes aligned in the rolling direction. In order to eliminate the effects of previous work-hardening and the effects of machining, the specimens were annealed for 15 min. at 750°F before testing. During tensile testing the loads were measured by means of a proving ring (sensitive to 1/2 lb) in series with the specimen.4 Strains were determined from the extension of a rack and pinion strain gauge sensitive to a strain of + 0.0001. The stress was recorded as the true stress, namely

Jan 1, 1950

By J. L. Taylor, Pol Duwez

THE present knowledge of the Ti-Al system is limited to the portion of the diagram extending from pure aluminum to the intermetallic compound TiAl3' A preliminary investigation of the titanium-rich Ti-A1 alloys revealed that the solubility of aluminum in titanium is quite extensive and that the transformation temperature of titanium is raised by alloying with aluminum. From an X-ray diffraction study of alloys containing up to 75 atomic pct Al (TiAl3), the phase boundaries at 750°C were located as follows: the a titanium solid solution extends from 0 to about 36 atomic pct Al, a two-phase region exists from 36 to 46 atomic pct Al, and an intermediate phase of varying concentration extends from 46 to 62 atomic pct Al. The purpose of the present paper is to describe the crystal structure of this new phase. The alloys were prepared by melting in a helium arc furnace on a water-cooled copper plate, using a furnace essentially the same as that described in ref. 2. The titanium metal was of the iodide type furnished by the New Jersey Zinc Co., and a piece of pure aluminum (99.99 pct) was obtained through the courtesy of the Aluminum Co. of America. After melting, the samples, weighing approximately 5 g, were sealed in evacuated fused silica tubes and homogenized for 4 hr at 1000°C. The specimens were then held for 10 days at 750°C and rapidly cooled to room temperature. Filings were then taken from each sample, sealed in evacuated vials, annealed at 750°C for 4 hr, and rapidly cooled to room temperature by quenching the vials in water. Powder diffraction patterns were obtained with a 14.32 cm diam camera, using K copper radiation filtered through a nickel foil. Structure Determination The X-ray diffraction patterns of the alloys containing 46, 50, 55. 60, and 62 atomic pct Al were identical, except for a slight shift in the positions of the reflections. The alloy containing 55 atomic pct Al was chosen far structure determination. The powder pattern contained 37 reflections and the a, doublets were well resolved in the back-reflection range. The relatively small number of reflections and the sharpness of the pattern were considered as an indication of a simple atomic arrangement in a relatively small unit cell of high symmetry, and an attempt was therefore made to solve the structure without single crystal work. A satisfactory fit was found on a large scale Hull-Davey tetragonal chart for an axial ratio of approximately 1.45. All the reflections were readily indexed and the tentative unit cell dimensions were computed to be a - 2.81 kX, c - 4.07 kX, and c/a = 1.448. The indices (hkl) and the values of d and sin2 A are given in Table I. The agreement between observed and computed sin2 is quite satisfactory. Once the unit cell was known, the details of the structure were readily found. First, it is obvious that the number of atoms per unit cell cannot exceed two, since more than two atoms would lead to a density greater than that of pure titanium. The next logical step is to assume that the two atoms occupy the corner and center of the cell. If this assumption is correct, the structure may be described as follows: space group D1, - P 4/mmm; one titanium atom in a: 000; one aluminum atom in d: 1/2 1/2 1/2: and no extinctions. Assuming this structure to be the correct one. intensities were computed by means of the usual equation: sin2 0 cos 0 where F is the structure factor; 8, the Bragg angle. and p, the multiplicity factor. The calculated values of intensities are compared in Table I with the visually estimated intensities. The agreement is quite satisfactory and the structure is therefore confirmed. The crystal structure of TiAl just described is the same as that of AuCu ordered. The AuCu ordered

Jan 1, 1953

By C. G. Bieber, J. R. Mihalisin, R. T. Grant

A growing demand for longer service life of gas turbines has placed increasingly rigorous requiret~rents upon superalloys employed for that application. Long-titne testing at high temperature has revealed that phase transformations occur in all superalloys. A common one of particular interest is o formation. Presented here are studies made to identify a and to characterize its formation and effect on properties in three cast nickel-base superalloys—IN 100 alloy, alloy 713C, and alloy 713LC. Methods are discussed by which o can be eliminated or inhibited in IN 100 alloy and alloy 713C. Evidence was obtained to indicate that some types of o may be more detrimental than others. Limitations in the electron vacancy approach to o prevention are pointed out, and it is shown how alternative approaches, such as reducing a complex superalloy matrix to the form of a pseudo-ternary system permitting equilibrium diagram treatment, lead to additional insights into the formation of in these alloys. AROUND 1960. Beiber1 developed IN 100 alloy, which still remains one of the strongest commercially available nickel-base superalloys. The principle used in the design of this alloy was to produce large quantities of y' phase in a y matrix through the use of copious amounts of aluminum and titanium. In 1963, ROSS' showed that when certain heats of this alloy were held for a long time at 1650°F they formed an acicular phase, subsequently identified as a.3 a is a hard and brittle phase first discovered in the Fe-Cr system by Bain and Griffiths.4 They termed it the "B" constituent. Subsequently this same phase was found in other systems, primarily those of the transition elements, and acquired the name "a" by which it is now known. The crystal structure of the a phase was first determined in the Fe-Cr system in 1950.5 It was shown to be tetragonal with a c/a ratio of about 0.52. as is the case with a found in other systems. This characteristic crystal structure is now the means by which a is identified. In superalloys, such as IN 100 alloy. large amounts of o impair the high-temperature creep strength and drastically reduce room-temperature tensile ductility. Discovery of o phase in some heats of IN 100 alloy quickly led to investigations of other superalloys for similar transformations. It was found that many of the stronger, more highly alloyed. super-alloys were indeed susceptible to o formation. This investigation has been concentrated on three commercial alloys: IN 100 alloy, alloy 713C, and alloy 713LC. J.R.MIHALISIN,MemberAIME, and C.G.BIEBER are with The International Nickel Co., Inc., Paul D. Merica Research Laboratory, Sterling Forest, Suffern, N. Y. R. T. GRANT, Member AIME, is with The International Nickel Co., Inc., Pittsburgh, Pa. Manuscript submitted May 22. 1968. IMD A detailed study has been made of the phase transformations and their relation to a formation along with a consideration of electron vacancy approaches for predicting a-forming propensity in these alloys. EXPERIMENTAL PROCEDURE Phase transformations were studied by light and electron microscopy, electron diffraction, microprobe investigations, and X-ray diffraction. Specimens for light micrographic examination were prepared by conventional grinding and polishing followed by etching with glyceregia (2:l HC1/HNO3 + 3 glycerine by volume). Photomicrographs of stress-rupture specimens were taken adjacent to the fracture unless otherwise noted in the text. Negative replicas for electron microscopy were taken from surfaces electropolished with a solution of 15 pct H2SO4 in methanol. For carbon extraction replication, a solution of 10 pct HC1 in methanol was used. A Siemens Elmiskop I was used for all electron microscopy. Selected-area diffraction studies were made at 80 kv using evaporated aluminum for standardizing the patterns. A nondispersive electron microprobe attachment was used to analyze the extracted precipitates chemically. The fluorescent X-rays were recorded using a flow counter containing P10 gas (90 pct Ar-10 pct methane) with a beryllium window and a single-channel pulse-height analyzer. The pulses from the analyzer were passed to a scaler-ratemeter and differential curves of counting rate vs pulse amplitude were obtained. The base line of the analyzer was driven with a synchronous motor at 0.5 v per min and a channel width of 0.5 v. The time for 105 counts was printed out for each 0.5-v increment. The microscope was operated at 80 kv with beam currents of 1 to 20 pa. This equipment detects elements from atomic number 13 to 40. X-ray diffraction studies were usually made on residues electrolytically extracted in 10 pct HC1 in H2O, although in one case a pattern was obtained from an etched surface of a metallographic specimen. A Siemens Crystalloflex IV was used with iron-filtered CoKa radiation. X-ray patterns were recorded using a goniometer speed of : deg per min. The scintillation counter and pulse-height analyzer operated at a channel height of 10 v and a channel width of 12 v. The equipment was calibrated with a powdered gold standard. The residues usually contained a number of phases. several of which could not be found in the ASTM card file. In addition, as is shown for the case of a phase in IN 100 alloy, other phases had a somewhat different lattice parameter from that reported in the ASTM card file, making it difficult to separate and identify constituents by comparison with ASTM d spacings. For these reasons, phases were identified on the basis of the lattice parameter obtained by indexing the ob-

Jan 1, 1969

By A. L. Foell

The development of the modern blast furnace began more than one hundred years ago, with the abandonment of the small hillside furnaces. Its development, especially during the past 50 years, has been accomplished through a rapid succession of enlargements and improvements. The remarkable growth in furnace output during this period is a tribute to the engineers and operators who have constantly endeavored to build larger and more efficient blast furnaces. The blast-furnace operators and their mechanical and electrical maintenance staffs have originated most of the furnace improvements as a result of their practical operating experience. Furnace Lines About 50 years ago furnaces consisted of hearths about 11 ft. in diameter, which merged into rather high flat boshes, with no cylindrical section between the bosh and inwall and no cylindrical section at the stock line. Since then the lines of the furnace invariably have included a cylindrical section above the bosh and a cylindrical section at the stock line. Notable increases have been made in both hearth diameters and furnace heights. During the past 10 years hearth diameters in new and replaced furnace stacks have rather consistently fallen within the range of 25 to 28 ft. while their heights have varied be- tween 100 and 106 ft. The lines of most large furnaces using Mesabi ores have followed a fairly uniform pattern (Fig. I) in which the principal dimensions for 25-ft. hearth furnaces are as follows: Hearth diameter............... 25 it. o in. Height of bosh................. 10 ft. o in. Bosh angle.................... 81 1/2º Diameter top of bosh........... 28 ft. 0 in. Inwall batter per foot........... 15/16 Stock-line diameter............. 19 ft. 6 in. Large-bell diameter............. 14ft. 6 in. Height from iron notch to top ring casting...................... 100 ft. o in. In determining the size of a new furnace for the replacement of an existing stack or for an addition to productive capacity, it is not possible to formulate a procedure that can always be followed. Local conditions, requirements as to capacity, available raw materials and prospects for future expansion dictate the size of such proposed improvements or additions. However, where the immediate requirements indicate a stack or furnace of a certain productive capacity, and the future prospects indicate that more capacity can be utilized, it is well to consider building the furnace ior the ultimate capacity rather than to install a smaller hearth with provision for future enlargement. The decision to build the larger hearth and stack for the ultimate capacity probably will require no greater initial investment, since the saving in the cost of brickwork will about offset the greater cost of the hearth jacket, tuyere breast and bosh bands. In the meantime. the furnace of larger hearth dimensions, while operating below its ultimate output, will yield a better coke rate and

Jan 1, 1943

By A. L. Foell

The development of the modern blast furnace began more than one hundred years ago, with the abandonment of the small hillside furnaces. Its development, especially during the past 50 years, has been accomplished through a rapid succession of enlargements and improvements. The remarkable growth in furnace output during this period is a tribute to the engineers and operators who have constantly endeavored to build larger and more efficient blast furnaces. The blast-furnace operators and their mechanical and electrical maintenance staffs have originated most of the furnace improvements as a result of their practical operating experience. Furnace Lines About 50 years ago furnaces consisted of hearths about 11 ft. in diameter, which merged into rather high flat boshes, with no cylindrical section between the bosh and inwall and no cylindrical section at the stock line. Since then the lines of the furnace invariably have included a cylindrical section above the bosh and a cylindrical section at the stock line. Notable increases have been made in both hearth diameters and furnace heights. During the past 10 years hearth diameters in new and replaced furnace stacks have rather consistently fallen within the range of 25 to 28 ft. while their heights have varied be- tween 100 and 106 ft. The lines of most large furnaces using Mesabi ores have followed a fairly uniform pattern (Fig. I) in which the principal dimensions for 25-ft. hearth furnaces are as follows: Hearth diameter............... 25 it. o in. Height of bosh................. 10 ft. o in. Bosh angle.................... 81 1/2º Diameter top of bosh........... 28 ft. 0 in. Inwall batter per foot........... 15/16 Stock-line diameter............. 19 ft. 6 in. Large-bell diameter............. 14ft. 6 in. Height from iron notch to top ring casting...................... 100 ft. o in. In determining the size of a new furnace for the replacement of an existing stack or for an addition to productive capacity, it is not possible to formulate a procedure that can always be followed. Local conditions, requirements as to capacity, available raw materials and prospects for future expansion dictate the size of such proposed improvements or additions. However, where the immediate requirements indicate a stack or furnace of a certain productive capacity, and the future prospects indicate that more capacity can be utilized, it is well to consider building the furnace ior the ultimate capacity rather than to install a smaller hearth with provision for future enlargement. The decision to build the larger hearth and stack for the ultimate capacity probably will require no greater initial investment, since the saving in the cost of brickwork will about offset the greater cost of the hearth jacket, tuyere breast and bosh bands. In the meantime. the furnace of larger hearth dimensions, while operating below its ultimate output, will yield a better coke rate and

Jan 1, 1943

By C. E. Sims

THE carbon-oxygen reaction without doubt is the basic reaction in steelmaking. It is important on several counts: In the first place, carbon is the element that distinguishes steel from iron. It is the principal element controlling properties, and its control is of prime concern. Although the principal objective of the carbon-oxygen reaction is to oxidize excess carbon, the accompanying boil should not be underrated. The mechanical agitation, stirring, and mixing resulting from the boil are so useful in the distribution of heat and in promoting uniformity of composition in the bath that, were it not a natural accompaniment of the carbon-oxygen reaction, it is probable that something would have to be invented to replace it. The open-hearth operation, for example,, with the bath heated from above by radiation, would be impracticable without the carbon boil. The electric-arc furnace is somewhat less dependent on it, but every melter knows how much easier it is to gain temperature with minimum damage to refractories during the boil than with a dead bath. The motor action of the induced current of the induction furnace makes the carbon boil unnecessary but even there a severe oxidation has been found useful in giving greater freedom from porosity in certain steels. The quantitative aspects of the carbon-oxygen reaction have been given considerable attention by a large number of investigators, and the principles of physical chemistry have played an important part in these studies. Physical chemistry is the science of the mechanics and mathematics of chemical reactions. It is possible to study the mechanisms of reactions in a qualitative manner without reference to mathematics and thus obtain valuable concepts as to the manner in which the wheels go around. When it is desired to express quantitative relations in these reactions, however, resort to mathematics is not only convenient but necessary. Mathematics may also be regarded as the shorthand language of physical chemistry. A basic relation whose description requires numerous words may be expressed very simply by a mathematical formula or equation. A good example of this is the equilibrium constant for a chemical reaction. Expressed verbally, it is: When a chemical reaction has reached a condition of equilibrium, the product of the concentration of the reacting substances on one side of the equation, divided by the product of the concentration of the reacting substances on the other side, gives a quotient that is a constant at constant temperature. For the carbon-oxygen reaction C + 0 [=] CO this is expressed simply as [ ] where K (from the German Konstant) is the equilibrium constant for the reaction. Although mathematics is such a necessary and useful tool, it is also a potential pitfall. Mathematics in itself is an abstract science, which is not inhibited by consideration of mechanisms or materials.

Jan 1, 1947

By J. P. Hirth, G. M. Pound

The flux of evaporation J from {loo) , {111), and (110) planes of silver single crystals and from poly crystalline specimens was measured at 744°C under a high vacuum using a time average weight loss method. The evaporation coefficient a was computed from the measured flux and vapor pressure data through the relationship J = aPe/21rmkT. The evaporation coefficients for the close packed planes and the poly crystalline specimens were found to be about 0.4 providing tentative confirmation of the theoretical limiting law for evaporation of metal crystals, a = 73(P/Pe) + % . The (110) planes faceted to form (111) planes, resulting in a greater evaporating area and larger a . The evaporation morphology of the plane surfaces and the surfaces of spherical single crystals is described in some detail. RECENTLY a detailed theoretical analysis of the mechanism and kinetics of metal crystal evaporation was made.1'2 A mechanism for vaporization involving the recession of monatomic ledges across a metal surface was deduced, and evaporation rate equations were derived by considering the dynamics of these ledges. In most metals, the process of evaporation is one of dissociation of atoms from ledges, surface diffusion, and desorption. The gross vaporization rate is controlled by the surface diffusion and desorption rates. It was shown that the monatomic ledges, under the action of surface diffusion gradients, tend to assume a terminal velocity and spacing. Further, it was shown that crystal edges and grain boundaries are a ready source for monatomic ledges. In the case of evaporation of large, perfect crystals with clean, low-index surfaces, the kinetic treatment1 leads to a limiting law for crystal evaporation: where J is the gross flux of vaporization, a is the evaporation coefficient, Pe the equilibrium vapor pressure, m the atomic mass, k Boltzmann's constant, T the absolute temperature, and P the actual pressure of vapor over the crystal surface. Imperfections such as grain boundaries, pores, cracks, and macroscopic steps should have the effect of causing positive departures from this limiting law. Such an imperfection is a source for monatomic ledges, which, near their origin, are closely spaced and thus give rise to higher evaporation rates there. However, under many experimental conditions,' this effect should be negligible due to the relatively low concentration of imperfections. In general, a more important cause of positive departure should be screw dislocations, and the effect of these has been considered in some detai1.2,3 Monatomic ledges emanate from points where the surface is intersected by a dislocation with a screw component normal to the surface. The dynamics of ledges arising from a screw dislocation are similar to those of ledges arising from a crystal edge. There is a perturbed region near the origin where the monatomic ledges are, under certain experimental conditions, closely spaced and the

Jan 1, 1960

By L. D. Jaffe, D. C. Buffum

EARLIER the authors and coworkers had pre sented data on isothermal temper embrittlement of an SAE 3140 steel?' In that work, however, attention was concentrated on embrittlement at 575°C and below. Preliminary measurements showed that embrittlement at 675 °C was much mote rapid than would be expected from the data at the lower temperatures: and indicated the need for further work above 575°C. The possibility of an upper nose in the time-temperature embrittlement diagram above 575°C was pointed out. Procedure The same heat of SAE 3140 steel was used as in the previous work, and experimental methods were the same. All blanks were austenitized 1 hr at 900°C and water, quenched. Groups were then tempered 1 hr at 675"C, water quenched, and given embrittling treatments for times of 5 min to 240 hr at 675" to 600 °C, as shown in Table I. Other groups, after the temper and quench, were embrittled 48 to 1440 hr at 550°C. Another series was tempered 240 hr at 675"C, quenched, and held for various times at 650" to 375°C (Table 11). For comparison, a series was tempered for these same times at 700°, 675", and 650°C (Table 111). The Ae, temperature for this heat of steel had been determined as approximately 690°C;1*a the treatments at 700°C were introduced to determine the effects of tempering in a range where a little austenite would fonn. A large number of other treatments, involving holding at two temperatures in succession after the temper, and occasionally slow cooling or heating, were also studied. These treatments are listed in the tables. Austenitizing was done in air; all subsequent treatments were in salt. Blanks were always water quenched after the last treatment. The heat-treated blanks were machined to standard V-notch Charpy specimens. A transition curve for each group was obtained by breaking the specimens at various temperatures on a 217 ft-lb impact machine having a striking velocity of 16.8 fps, and plotting the observed percentage of fibrous fracture vs the test temperature. From this plot, the transition temperature was taken as the lowest temperature at which the fracture appeared 100 pct fibrous; its accuracy is estimated as +5"C. Generally, hardness was measured on every bar. Since a decrease in hardness itself seems to decrease the transition temperature somewhat, a correctiona of —0.28"C per Bhn was applied to permit comparison of the transition temperatures on a uniform basis of 24 Rc. The transition temperature and hardness results are given in Tables I through VI. Where overlap of earlier work1.' occurred, data were combined.

Jan 1, 1958

By C. R. Dodson, D. Goodwill, E. H. Mayer

The paper summarizes the historical background of the pressure-volume-temperature analyses of reservoir fluids, the errors involved in both the sampling and testing of reservoir fluids, the type of information required of a PVT determination, and the field conditions that limit the application of any one analysis. Particular emphasis is placed on the necessity for approximating as closely as possible the liberation sequence occurring in the producing formation, flow string, and surface separators. A combined differential and flash or "composite" liberation is suggested as the best means of approximating this liberation sequence. HISTORICAL BACKGROUND Petroleum reservoir engineering commonly is considered to be one of the newest fields of petroleum science, yet much work of a theoretical and intuitive nature was done many years before the modern techniques of reservoir analyses were developed. The period 1910-1924 saw considerable work in the field of reservoir behavior done by the U. S. Bureau of Mines. This work:.' although entirely theoretical, pointed out the importance of gas in the recovery of oil from the reservoir. The statement by J. 0. Lewis that 20 per cent or less of the oil originally in place in a pool was recovered from the ground under uncurtailed production conditions caused some operators to re-examine and modify their production methods. However, though these works showed methods of production that have subsequently resulted in greater oil recoveries, they in general went unnoticed, even though there was a fear that the nation's petroleum resources were being exhausted. The period 1924-1933 saw the industry take considerably more interest in reservoir behavior because of an unfounded fear of its inability to replace oil reserves, the possibility of government regulation, and the energy of one man, Henry L. Doherty. Doherty aroused heated discussions in the industry concerning conservation. To prove or disprove his theories the first experimental work on the reservoir behavior of petroleum was undertaken. The papers of Dow and Calkin,' Beecher and Parkhurst," and Mills and Heitheckere are classics although their experimental procedures were crude. These papers proved that the properties of petroleum in the reservoir are quite dissimilar to the properties measured at the well head. Gas dissolved in the oil phase was recognized as having considerable importance as had been predicted by the earlier theorists. Slightly later Miller and his co-workers assembled the first text correlating all the known data on the reservoir behavior of petroleum and used, these data to show the economic value of conservation. Quantitative application of pressure-volume-temperature analyses of reservoir fluids was given in the paper of Coleman, Wilde, and Moore"; this work showed that with sufficient laboratory and production data prediction of reservoir behavior was possible. The refined sampling and labora-

Jan 1, 1953

By Walter Crafts, C. M. Offenhauer

In a previous study of the carbide phase of chromium steels, it was shown that chromium carbide (Cr7C3) is 2 more stable carbide than cementite (Fe3C) at tempering temperatures above about 500°C. in quenched steels containing from about I to 7.5 per cent chromium. Below this temperature the carbide phase was found to consist of cementite in all of the steels examined. In the present investigation it was found that a similar change in the carbide phase takes place in molybdenum and in chromium-molybdenum steels at approximately the same tempering temperatures. The approximate ranges of occurrence of the alloy carbides Cr7C3, Cr4C, and Mo2C have been determined in steels containing up to 5 per cent chromium, I per cent molybdenum and 0.60 per cent carbon. The experimental steels were made in small high-frequency furnaces from Armco ingot iron, low-carbon ferrochromium and calcium molybdate and were poured into 2-in. ingots, which were forged to I-in. round bars. Sections of the bars were heated to the carbide-solution temperature and cooled rapidly to induce austenite transformation at relatively low temperatures. The steels were subject to some segregation, therefore comparatively high temperatures were necessary to dissolve all of the carbides. The microstructure of the quenched specimens was examined to verify the belief that the carbides had been dissolved, and also to determine the nature of the nonmartensitic structure of incompletely hardened steels. Ferrite and pseudo-martensite were present in some of the specimens, but all specimens were quenched at such a rate that pearlite was not formed, in order to ensure the formation of the carbides at temperatures lower than about 500°C. It had been found previously1 that in chromium steels the chromium carbide could be produced by transformation of austenite in the pearlite range above 500°C., and, in order to start the tempering treatment with the carbide present as cementite, the absence of pearlite was considered to be essential. The specimens were tempered for 64 hr. to permit the formation of the stable carbide. After tempering, the specimens were submitted to microscopic and X-ray examination. The carbides were separated either electrolytically in a 5 per cent HCl electrolyte or with an acidified copper-potassium chloride solution. The crystal structure of the carbide phases was determined by the Debye-Scherrer type of X-ray patterns. The X-ray patterns obtained from specimens near the boundaries between two types of carbides were generally weak and diffuse as compared with the other patterns. For this reason, and because the more soluble components may be masked, the boundaries between the phases could not be determined precisely. However, the X-ray analysis of electrolytically separated carbides has given consistently reproducible results

Jan 1, 1943

By Walter Crafts, C. M. Offenhauer

In a previous study of the carbide phase of chromium steels, it was shown that chromium carbide (Cr7C3) is 2 more stable carbide than cementite (Fe3C) at tempering temperatures above about 500°C. in quenched steels containing from about I to 7.5 per cent chromium. Below this temperature the carbide phase was found to consist of cementite in all of the steels examined. In the present investigation it was found that a similar change in the carbide phase takes place in molybdenum and in chromium-molybdenum steels at approximately the same tempering temperatures. The approximate ranges of occurrence of the alloy carbides Cr7C3, Cr4C, and Mo2C have been determined in steels containing up to 5 per cent chromium, I per cent molybdenum and 0.60 per cent carbon. The experimental steels were made in small high-frequency furnaces from Armco ingot iron, low-carbon ferrochromium and calcium molybdate and were poured into 2-in. ingots, which were forged to I-in. round bars. Sections of the bars were heated to the carbide-solution temperature and cooled rapidly to induce austenite transformation at relatively low temperatures. The steels were subject to some segregation, therefore comparatively high temperatures were necessary to dissolve all of the carbides. The microstructure of the quenched specimens was examined to verify the belief that the carbides had been dissolved, and also to determine the nature of the nonmartensitic structure of incompletely hardened steels. Ferrite and pseudo-martensite were present in some of the specimens, but all specimens were quenched at such a rate that pearlite was not formed, in order to ensure the formation of the carbides at temperatures lower than about 500°C. It had been found previously1 that in chromium steels the chromium carbide could be produced by transformation of austenite in the pearlite range above 500°C., and, in order to start the tempering treatment with the carbide present as cementite, the absence of pearlite was considered to be essential. The specimens were tempered for 64 hr. to permit the formation of the stable carbide. After tempering, the specimens were submitted to microscopic and X-ray examination. The carbides were separated either electrolytically in a 5 per cent HCl electrolyte or with an acidified copper-potassium chloride solution. The crystal structure of the carbide phases was determined by the Debye-Scherrer type of X-ray patterns. The X-ray patterns obtained from specimens near the boundaries between two types of carbides were generally weak and diffuse as compared with the other patterns. For this reason, and because the more soluble components may be masked, the boundaries between the phases could not be determined precisely. However, the X-ray analysis of electrolytically separated carbides has given consistently reproducible results

Jan 1, 1943