Search Documents

By A. M. Gaudin

CHANGES in industrial practice, in plant design, and in research methods which are so clearly to be seen on every hand, have affected the mineral industry as well as others. In particular, ore dressing has passed through a revolution in practice brought about by the introduction of flotation and other quasi-chemical methods, until it has ceased to be solely the mechanical preparation of ores. In fact, the term "ore dressing" itself is obsolescent, and "mineral dressing" has been growing in popularity. This assures adequate recognition of the fact that mineral substances other than ores, e.g. coals, clays, and cement rock, are treated by the same general methods. As a result of these industrial changes it was felt that a complete rearrangement of the curriculum and laboratories at the Massachusetts Institute of Technology would be ad-vantageous. Such a rearrangement would allow instruction and research to proceed in wider accord with industrial evolution and the needs of our times.

Jan 1, 1942

By F. Julius Fohs

CENTRALLY located with relation to the largest iron- and steel-producing districts of the United States, the fluorspar-deposits of Kentucky possess increasing interest and importance. As typical of the numerous fluorspar-mines of Kentucky and Illinois, I have selected for description the Memphis., because it and others of its immediate group exhibit the conditions characteristic of all. I. THE MEMPHIS MINE. This mine lies 5 miles NW. of Marion, in Crittenden county, Kentucky, a station on the Chicago and Nashville division of the Illinois Central R. R. For the first mile and a half out of Marion we see only Birdsville or Middle Chester sandstones of Mississippian age. Then we cross a fault of some 350 ft. displacement, and the Ste. Genevieve oolite sets in. Beyond the fault, oolite is the predominant rock, except that the bills to the north have a capping of Cypress or lowest Chester sandstone, 80 ft. below which is an outcrop of from 6 to 10 ft. of Ste. Genevieve (Rosiclare) sandstone. Occasional sink-holes are noticed, and as the mines are approached evidence of faulting is again seen.. A line of crude head-frames and open-cut dumps, extending for more than a quarter of a mile, marks the Klondike vein. The open-cuts are from 15 to 20 ft. deep, and in most of them, from the surface down, was found the reddish gravel which is really fluorspar-some of it white or purple and crystal-clear (if the red clay is washed off), and some carrying iron and silica, and stained by waters from the decaying limestone walls. In one of these cuts, at a depth of 20 ft., white and purplish honey-combed fluorspar was found, in which the larger cavities are due to limestone and calcite leaching, and the minute ones to the leaching of zinc-blende.

Apr 1, 1909

By E. M. Norris

THE Western phosphate deposits extend over a large area in the Rocky Mountain region, comprising portions of south central Montana, southeastern Idaho, northeastern Utah, and southwestern Wyoming. A limited acreage of these deposits passed into private ownership prior to Dec. 9, 1908, at which time 7000 sq. mi. of land in these phosphate fields was withdrawn from public entry by direction of the Secretary of the Interior. Under the Act of Feb. 25, 1920 (41 Stat. 437) title to all phosphate lands in the public domain was reserved to the United States with provisions for leasing portions to citizens, corporations, states, etc. The above act, in effect, created by law a Western phosphate reserve of approximately 2,269,055 acres.

Jan 1, 1944

By Mark J. Klein

The behavior of nitrogen in Cr-0.12 at. pct Y was studied in specimens of varying interstitial concentration and thermal history. It was found that soluble nitrogen can be introduced into this alloy by increasing the concentrations of either oxygen or nitrogen. For low nitrogen concentrations the nitrogen in solution is low relative to that in unalloyed chromium. However, the nitrogen in solution increases with increasing nitrogen concentration, approaching that in unalloyed chromium. When the alloy is supersaturated with nitrogen, the nitrogen precipitates readily from solution as a chromium nitride. The stress -induced relaxation of nitrogen is influenced by internal oxidation or internal nitrification of this alloy. THE addition of small concentrations of reactive elements such as yttrium have been found to enhance the low-temperature ductility of chromium.&apos; However, the mechanism by which the ductility is increased is not known. It has been suggested that this effect is caused by a drastic reduction in the concentration of nitrogen retained in solution and therefore a decrease in the number of dislocations locked by nitrogen, a factor that has been associated with an increase in ductility.1,2 However, a change in the type of interstitial precipitate induced by yttrium could also contribute to enhanced ductility of the alloy, since chromium nitride precipitates appear to be embrittling.&apos; In this regard, it has been shown that yttrium scavenges nitrogen in chromium to form YN,4 thus reducing the embrittling chromium nitride phase. However, the change in nitrogen solubility induced by yttrium and the partition of nitrogen between chromium and yttrium nitrides are not known. The object of this investigation is to study the effect of yttrium on the behavior of nitrogen in chromium to obtain information relevant to the mechanism by which scavengers enhance the ductility of chromium. EXPERIMENTAL PROCEDURES The experimental procedures used in this investigation have been described in detail elsewhere.5,6 Wires of Cr-0.12 at. pct Y, 15 cm in length and 1 mm in diam, were drawn from rods 0.6 cm in diam supplied by the General Electric Co. The grain size of the wires after recrystallization at 1150°C was somewhat nonuniform, varying from 0.006 to 0.06 mm in diam. The interstitial analysis for the wires in ppm by weight was about 160 0, 80 N, 12 C, and <2 H. Heat treatments were carried out after encapsulation of the specimens in quartz tubes containing argon. Changes in interstitial concentrations, or interstitial "loading" as it is termed in this study, were generally accomplished by annealing in oxygen, ammonia or methane at 1150°C. The internal friction was measured using a conventional torsional pendulum enclosed in an evacuated chamber. Electrical-resistivity measurements were made at liquid-nitrogen temperature.

Jan 1, 1967

By Jose A. Ruiz

INTRODUCTION For heterogeneous non-catalytic solid-gas reactions carried out in fluidized bed reactors, nominal bed temperature is an average value between gas and solid. For highly exothermic reactions, actual particle temperature can be up to hundred degrees above termocouple temperature, since heat dissipate at slower rate than heat generation during some steps of transformation. These micro instabilities at particle level can displace thermodynamic equilibrium from the desired phase to others. This effect is important when relatively narrow range of phase stability exists, like in sulphation roasting of sulphides, where bed discharge contains, in addition to the desired sulphate others metastable phases such as basic sulphate and ferrite. For example, for copper-iron sulphide concentration roasted below 680°C, no cupric ferrite is formed, as shown by Jakob et al., therefore the separate Kellogg&apos;s stability phase diagrams Cu-S-O represent the roasting (Fig.l). At temperature above this one, like 760°C for example, phase stability changes from CuSO4 to the basic sulphate Cu0•CuSO4. Solid state reaction between Cu0•CuSO4 and Fe203 also occurs to form cupric ferrite, Cu0•Fe2O3, therefore the Cu-Fe-S-O Kellogg&apos;s phase diagram of Fig. 1 (continuous line) represents this condition of roasting. Although both Cu0•CuSO4 and Cu0•Fe2O3 are metastable phases under normal operating conditions of sulphation roasting(1-10% SO2, 1-10% 02 and 680°C, points A and B,Fig. 1) sulphation of these species and particularly ferrite are slow and limited due to diffusional control. This explain why reactors discharge contains several phases: CuSO4, Cu0•CuSO4, CuO•Fe203 plus small amounts of CuS and FeS due to the baclonixed conditions of fluidized bed reactors. The presence of cuprous ferrite due to reducing conditions inside individual particles also occurs, but in very limited extent at the reaction interface, as it is demonstrated by the low soluble iron levels of calcines. On the other hand, the presence of cupric ferrites can be explained only due to the higher temperature achieved by particles, since below 680°C cupric ferrite formation does not take place. [ ] This phenomena also occurs for others non-ferrous metal sulphides concentrates roasted under sulphation conditions, such as 7n, Co and Ni. Therefore the prediction of discharge composition of fluidized beds is not possible based only on kinetics and mechanistics models alone or purely thermodynamical considerations, since all factors should be integrated to describe the overall phenomena. SINGLE PARTICLE TRANSFORMATION Assuming a first order reaction with respect to the gas and zero for solid, such as

Jan 1, 1984

By P. W. Bakarian

Previous determinationl,2,3 of the texture of magnesium and its alloys have shown only slight variations in the principal features of the structure. This investigation presents pole figures for magnesium and two of its alloys, in which differences of some magnitude will be shown. Schmid and Wassermann have considered the texture of magnesium in analogy with that of zinc—also a hexagonal lattice. Whereas the zinc texture is said to be derived primarily through basal slip and secondarily through {IO2}† twinning, the {102} twinning is considered impossible at the later stages of the rolling in magnesium because of its smaller axial ratio. This state of affairs appears reasonable for pure magnesium, but for alloy textures the situation is more complex. A double orientation similar to that found in zinc has been reported by J. D. Hanawalt,4 and the addition of small amounts of calcium to magnesium and its alloys to produce a double texture was noted by J. C. McDonald.5 The pole figures of this investigation, using an improved X-ray technique, show these various textures. The dependence of directional properties of rolled sheet on modifications of texture is well recognized. Correlation of physical properties with existing texture should be even more significant if quantitative valuations are attached to the various areas on the pole figures. Such a quantitative technique is developed herein. Experimental Method Two alloys were used, besides high-purity magnesium. In each case, the metal was extruded to bars 1/2 in. thick and hot-rolled to a thickness of about 0.075 in. It had been established previously that such a reduction was more than sufficient to eliminate the extruded structure. The rolling proceeded in the same direction as that of the extrusion, without any cross rolling. The temperatures corresponded to normal commercial practice, averaging around 600°F. A unique method of preparing the sample was developed in this work. Instead of using a flat specimen, a stem of the metal was cut out of the rolled sheet in the desired direction (rolling direction) as shown in Fig. I. From a sheet of 0.075 to 0.065-in. gauge, the stem was cut to a square cross section with a jeweler&apos;s saw, rounded with a file and polishing paper to a diameter of 0.060 in. and evenly etched in dilute hydrochloric acid to a diameter of 0.038 + 0.001 in. In this way, a cylinder of the original sheet with its axis in the desired direction was produced. By using this type of specimen for the pin-point pictures, any variance in the absorption of the diffracted beam at the various angular settings of the specimen, was completely eliminated.*

Jan 1, 1942

By P. W. Bakarian

Previous determinationl,2,3 of the texture of magnesium and its alloys have shown only slight variations in the principal features of the structure. This investigation presents pole figures for magnesium and two of its alloys, in which differences of some magnitude will be shown. Schmid and Wassermann have considered the texture of magnesium in analogy with that of zinc—also a hexagonal lattice. Whereas the zinc texture is said to be derived primarily through basal slip and secondarily through {IO2}† twinning, the {102} twinning is considered impossible at the later stages of the rolling in magnesium because of its smaller axial ratio. This state of affairs appears reasonable for pure magnesium, but for alloy textures the situation is more complex. A double orientation similar to that found in zinc has been reported by J. D. Hanawalt,4 and the addition of small amounts of calcium to magnesium and its alloys to produce a double texture was noted by J. C. McDonald.5 The pole figures of this investigation, using an improved X-ray technique, show these various textures. The dependence of directional properties of rolled sheet on modifications of texture is well recognized. Correlation of physical properties with existing texture should be even more significant if quantitative valuations are attached to the various areas on the pole figures. Such a quantitative technique is developed herein. Experimental Method Two alloys were used, besides high-purity magnesium. In each case, the metal was extruded to bars 1/2 in. thick and hot-rolled to a thickness of about 0.075 in. It had been established previously that such a reduction was more than sufficient to eliminate the extruded structure. The rolling proceeded in the same direction as that of the extrusion, without any cross rolling. The temperatures corresponded to normal commercial practice, averaging around 600°F. A unique method of preparing the sample was developed in this work. Instead of using a flat specimen, a stem of the metal was cut out of the rolled sheet in the desired direction (rolling direction) as shown in Fig. I. From a sheet of 0.075 to 0.065-in. gauge, the stem was cut to a square cross section with a jeweler&apos;s saw, rounded with a file and polishing paper to a diameter of 0.060 in. and evenly etched in dilute hydrochloric acid to a diameter of 0.038 + 0.001 in. In this way, a cylinder of the original sheet with its axis in the desired direction was produced. By using this type of specimen for the pin-point pictures, any variance in the absorption of the diffracted beam at the various angular settings of the specimen, was completely eliminated.*

Jan 1, 1942

By C. G. Dunn

IDENTIFICATION Of the kinds of orientation relationships that may exist among crystals is an important problem in the metallurgical field. As an aid to its solution standard orientations of several orders of twins would be very useful for rapid analyses to discover high-order as well as low-order twin relationships. Although data have been published that give orientations for three generations of twins, these data are not readily useful in the form presented; i.e., in a stereographic projection with one pole per orientation.1 However, accurate data based on calculations of the positions of all {100} planes for such groups would be very useful when presented in tabular form. Therefore, calculations have been made for a group of four orders of twins and the data are listed in Table 3. Illustrative applications are considered briefly, with the idea of pointing out what may be done with large groups of orientations. METHOD OF COMPUTING ORIENTATION OF A TWIN It is common practice to describe the orientation of a crystal in terms of the positions on a stereographic net of the poles of certain planes of the crystal. A single position on a net may be given it terms of two angle variables, two sets of which appear in the following equations: [Polar NetWalff Net x=rsinOocos4pyx=rcos0. y=rsinB,sin4,ny-rsin0.cos¢,, z=rcos0,,z=rsin0.sin4,,] The three numbers x, y and z determine a length r as well as a direction [(0, 0)] in an X, Y, Z coordinate system. In the present case, r will be set equal to (h2 + k2 +12)1/3, where h, k and 1 are the usual Miller indices for a crystallographic plane, a restriction that facilitates determination of the positions of poles of new planes from those of old or known ones,2 as will become evident later. Furthermore, since twinned lattices have certain planes in common, it is an easy matter to determine the orientation of a twin of a crystal if the orientation of the crystal itself is known. We start therefore with a crystal of known orientation (positions of three {100} poles given) and determine where the cube poles occur in first, second, third and fourth-order twins. Methods for identifying twinned lattices and for making the calculations to find the orientation of a twin have been published.3 4 Reference 4 will be illustrated in the calculation of the orientation of a twin, even though this method differs from the one used by the writer in obtaining the following data on four orders of twins. Consider a crystal S and its twin A1, A1 being one of the four {112} or {III}

Jan 1, 1945

By Ursula E. Wolff

Il.lechanica1 twins have been observed in brigsten single crystals of a variety of axial orientations defornzed at room temperature in tension or bending. The twins formed near the final fracture and were up to 3 p thick. The twinning plane was always of the type (113). Twinning at room ternperature occurred only after considerable prior slip. Twins usually preceded fracture and nucleated cracks. The crack surfaces often alternated between a (001) plane and the twin interfaces. Secondary twins could also nucleate from cracks. In the absence of twinning tensile samples failed by shear; twinned samples failed by cleavage. On the assumption that observed sudden load drops in the stress-strain curves are associated with twinning, a critical resolved stress for twinning of 60, 000 to 65, 000 psi was calculated. MeCHANICAL twinning has been observed in iron and iron alloys at low temperature by a number of investigators.&apos;-7 Similarly, for high-purity tungsten, twinning has been reported for deformation temperatures below 211°K.8-10 In W-Re and Mo-Re alloys, 20 pct Re was determined as the lower limit for twin formation at room temperature." Since the twins are generally very narrow, they are usually identified only by etching techniques. The expected (112) habit plane has always been confirmed by angular analysis of the surface traces. Recently, however, a complete identification by X-ray analysis has been performed on twins in a Mo-35 pct Re alloy.12 During an investigation of the deformation charac- teristics of tungsten single crystals, twins were revealed in tensile and bend samples deformed at room temperature. This paper deals with the conditions for such twinning and the relation of twinning to fracture. EXPERIMENTAL PROCEDURE Tungsten single crystals, 1/8 in. in diam, of a variety of axial orientations were grown from un-doped material by four-pass electron-beam zone melting. A representative analysis is given in the following table: From these crqstals, tensile samples with 1 in. gage lengths were made by surface grinding, leaving shoulders for gripping. The diameter after grinding was 0.082 in. The distorted surface layer was then removed by ele1:trolytic polishing which reduced the diameter of the gage length to 0.080 in. Tensile tests were carried out at room temperature in an Instron machine under two different sets of conditions: a) Rigid mounting; strain rate 0.02 in. per in. per min. b) Gimbal mounting; strain rate 0.002 in. per in. per min up to a total strain of approximately 0.2 pct, then 0.01 in. per in. per min to fracture. Stress axis and growth direction coincided in all samples and are subsequently called orientation.

Jan 1, 1962

By Edwin T. Myskowski, Alfred H. Hesse

THE development by the U. S. Bureau of Mines of a process for purifying manganese by electrolysis has stimulated interest in manganese alloys. While recent publications have shown some alloys of manganese and copper to possess rather unusual properties, none have included information on tensile properties, which have an important bearing on the usefulness of the alloys. Manganese-copper alloys can be heat-treated, since the single phases that exist at high temperatures may be retained by quenching. According to Persson,1 when quenched alloys containing from about 30 to nearly i00 per cent manganese are reheated, alpha manganese is precipitated (Fig. I). Calculations based on Persson&apos;s X-ray data indicate that this decomposi¬tion is accompanied by a change in volume of as much as S per cent. The reason that this large volume change has not been noted probably is the slow rate at which equilibrium is reached by these alloys. In an investigation on hardening by cold-work and heat-treatment, Dean and Anderson3 found that quenched alloys increase in hardness with manganese content and that high-manganese alloys harden very slowly with cold-work, while high-copper alloys harden much more rapidly. Heat-treatment has little effect on manganese-copper alloys containing less than 40 per cent Mn, and affects those alloys containing more than 40 per cent in accordance with their manganese content and heat-treating temperature. Dean and Anderson4 also found that cold-work increased electrical resistance of alloys containing from 50 to 80 per cent Mn, and that heat-treatment of alloys containing from 40 to 96 per cent Mn altered the electrical resistance considerably. Dean, Anderson and Potters have shown that the high vibration damping capacity that characterizes manganese-copper alloys containing 40 to g0 per cent Mn. is affected by cold-work and heat-treatments. Highest vibration damping capacity at low stresses was obtained by heating for 2 hr. at 450°C. (842°F.) after quenching from solution temperatures. Preparation of Alloys.-The alloys for these tests were melted in a 17-lb. basic-lined high-frequency induction furnace using electrolytic manganese, grade A ingot copper and a 70-30 Cu-Mn master alloy (69.80 per cent Cu, 0.12 Fe, 0.04 Si, 0.006 S, 0.07 C, balance Mn). The manganese was heated slowly to expel excess dissolved gases and melted before the addition of copper. No fluxes or covers were used. The melts were cast in tapered iron molds and the ingots were reduced go per cent when forged to ½ in. rounds. These rods were given 2-hr. solution treatments at temperatures that depended upon the composition (Table I). Tensile Tests.-The tensile specimens, 0.313-in. diameter (1.25-in. gauge length), which were enclosed in evacuated Pyrex

Jan 1, 1942

By J. W. Spretnak, V. Kandarpa, G. W. Powell, R. A. Erickson

Neutron-diffraction pattens were obtained at room temperature from two austenitic manganese steels, oxc wth n carbon content of 1.23 zct PC/ and the olher 0.63 wt pct. Analysis of the data showed that the curOan atols (ions) occupy tile octaheadral site. any of the cavbon is in the tetahedral site, tile concentration is too strzall lo be detecled by tzeulr-on d$facton. AS part of a long-range investigation of eutectoid decomposition, a study of the structure of austenite has been undertaken in order to characterize as best as possible the parent phase in the Fe-C system. Austenite is a solid solution of carbon atoms in fcc iron, the carbon atoms being located in interstitial positions. Of the two kinds of interstitial sites, octahedral (0, +, +) and tetrahedral (4, a, $), in this lattice, the larger octahedral sites are usually considered as the probable position of carbon. The strain energy involved in pytting a neutral carbon atom (covalent di; ameter 1.54)&apos; into a tetrahedral site (diameter 0.56A) is considerably greater than that associated with p2tting carbon into the octahedral site (diameter 1.08A). Dayal and arkeen&apos; observed the migration of carbon in iron under the influence of an electric field indicating tha tye carbon is ionized. pe ionic radius of C&apos;4 is 0.15A and that of C" is 0.29. Consequently, it is conceivable that carbon ions could occupy the tetrahedral sites if one considers only the strain energy. Size considerations alone do not provide a complete explanation for the formation of the interstitial solid solutions, however. because metals such as copper, zinc, and cadmium do not appear to form interstitial solid solutions in spite of their large interstitial sites. Evidence which suggests partial ioni-zation of the carbon in austenite has also been obtained by Speiser, Spretnak, and alor who derived formu- lae relating the observed change in lattice parameter to the effective diameter of the solute atom. Assuming the carbon occupies the octahedral site. they computed the effective diameter of carbon to be 1.33A whereas the covalent diameter is 1.54A. petch5 concluded from powder X-ray diffraction experiments that carbon atoms occupy the octahedral sites. His conclusion was based on the general trend observed in the intensity of the diffraction lines as the carbon content of the austenite was increased. However, the major difficulty associated with application of X-ray diffraction to this particular problem is the relatively poor scattering power of carbon. Williamson and smallman&apos; utilized X-ray diffraction to study the line broadening caused by the strain field about carbon atoms inferrite: these investigators concluded that at least 85 pct of the carbon in ferrite occupies the octahedral (0: 3, B) site rather than the larger

Jan 1, 1967

By P. W. Bakarian

PREVIOUS determinations1,2,3 of the texture of magnesium and its alloys have shown only slight variations in the principal features of the structure. This investigation presents pole figures for magnesium and two of its alloys, in which differences of some magnitude will be shown. Schmid and Wassermann have considered the texture of magnesium in analogy with that of zinc-also a hexagonal lattice. Whereas the zinc texture is said to be derived primarily through basal slip and secondarily through {102}† twinning, the {102} twinning is considered impossible at the later stages of the rolling in magnesium because of its smaller axial ratio. This state of affairs appears reasonable for pure magnesium, but for alloy textures the situation is more complex. A double orientation similar to that found in zinc has been reported by J. D. Hanawalt,4 and the addition of small amounts of calcium to magnesium and its alloys to produce a double texture was noted by J. C. McDonald.5 The pole figures of this investigation, using an improved X-ray technique, show these various textures. The dependence of directional properties of rolled sheet on modifications of texture is well recognized. Correlation of physical properties with existing texture should be even more significant if quantitative valuations are attached to the various areas on the pole figures. Such a quantitative technique is developed herein. EXPERIMENTAL METHOD Two alloys were used, besides high-purity magnesium. In each case, the metal was extruded to bars 32 in. thick and hot-rolled to a thickness of about 0.075 in. It had been established previously that such a reduction was more than sufficient to eliminate the extruded structure. The rolling proceeded in the same direction as that of the extrusion, without any cross rolling. The temperatures corresponded to normal commercial practice, averaging around 600°F. A unique method of preparing the sample was developed in this work. Instead of using a flat specimen, a stem of the metal was cut out of the rolled sheet in the desired direction (rolling direction) as shown in Fig. 2. From a sheet of 0.075 to 0.065-in. gauge, the stem was cut to a square cross section with a jeweler&apos;s saw, rounded with a file and polishing paper to a diameter of 0.060 in, and evenly etched in dilute hydrochloric acid to a diameter of 0.038 ± 0.001 in. In this way, a cylinder of the original sheet with its axis in the desired direction was produced. By using this type of specimen for the pin-point pictures, any variance in the absorption of the diffracted beam at the various angular settings of the specimen, was completely eliminated.*

Jan 1, 1941

By W. S. Ayres

By H. D. Outmans

The author applies the theory of hydrodynamic stability to fluid flow in porous media and concludes that the displacement of miscible liquids is stable if the stability coefficient, as defined by Eq. 19.2 or Eq. 27.0, is positive. The conclusion is invalid, however, since it is based on a faulty argument. To demonstrate this, the reader is referred to Eqs. 4.1 through 4.5 of the paper which describe, in differential form, the first-order disturbances c, u, v, w and p. In these same equations, cx, cz, gl, g3 and are functions of the stable concentration c. This concentration c is known and depends on x, z and t (the author assumes cy = 0). It follows that cx, cz, gl, g3 and µ are also functions of x, z and t. With this in mind, we turn to Eqs. 8.1 through 8.5 which were derived from Eqs. 4.1 through 4.5 by substituting Eq. 6.0. The significance of this substitution is that the author thereby limits the solutions of Eqs. 4.1 through 4.5 to equations of the form of Eq. 6.0. Eqs. 8.1 through 8.5 represent an infinite linear system with five unknowns: c, u, v, w and p. The coefficients cx, cz, gl, g3 and µ in this system are known at each point and at each instant; the coefficients containing derivatives of f are unknown. If this infinite linear system in c, u, v, w and p is to have a nontrivial solution, then it is indeed necessary (as the author states) that the determinant of the coefficient matrix of Eqs. 8.1 through 8.5, i.e., ( A 1, be equal to zero. This condition, however, is not sufficient. A non-trivial solution exists if, and only if, the rank of the coefficient matrix of the entire infinite system is smaller than five. In other words. all minors of order five must vanish and only if all the coefficients in Eqs. 8.1 through 8.5 are constant is this equivalent to the condition |A| =0. Constant coefficients means that gl, g3 and µ, for instance, are constant; and, since they depend on c it follows that c must be constant. We conclude that the condition I A I = 0, on which the author bases his calculations, is necessary and sufficient for a nontrivial solution only if the concentration c is constant. In other words, the author does not investigate the stability of a miscible displacement but, rather, only the stability of the flow of a homogeneous liquid. Using the initial condition and the fact that the coefficients are constant, we find

By David A. Thomas, Eugene S. Meieran

MECHAMCAL, electrical, and other property measurements are often more easily made on wires than on sheets. In order to carry out transmission electron microscopy on the same material used for property determinations, we have developed a method for preparing thin foil specimens of wires. The technique was developed for 0.030 in. diam tungsten wires, and is a modification of the thinning techniques used by Wilsdorf, et al 1 A length of wire is first ground to about 0.010 in. thick by mounting the wire in low melting temperature wax, hand grinding a longitudinal flat, removing and reversing the wire in the mount, and then grinding a second parallel flat. The 0.030 in. wide and 0.010 in. thick strip is cut into 1/8 in. lengths to fit in the specimen holder of the electron microscope. Next the specimen is gripped in platinum-tipped tweezers (the anode) and placed 2 mm below a hol- low copper cathode with a 0.010 in. ID nozzle. Electrolyte, 10 pct NaOH, flows by gravity feed through the nozzle onto the specimen, as shown in Fig. l(a). Polishing is carried out until a shallow impression is made on one surface, and then the specimen is turned over and the opposite surface indented. The metal between the two impressions should be about half the specimen thickness, as is shown by the heavy line in the cross section in Fig. l(b). The entire specimen is then electropolishedin 2 pct NaOH until a hole appears at the location of the indentations. The apparatus is shown in Fig. 2, and is essentially the same as that used by Wilsdorf et al. at The Franklin Institute. Light is reflected by a mirror onto the bottom surface of the specimen! which is viewed by a stereoscopic microscope placed above it. Polishing is carried out until light is seen, indicating that a hole has formed, and then immediately stopped. The specimen is washed in water. alcohol, and ether, and is then ready for examination. The specimen should be reversed in its platinum clip during electropolishing to insure equal polishing on both sides of the impression. For tungsten, indenting at 120 v and 0.04 amp takes less than 1 min, and final polishing, at 10 v and 1 amp, less than 5 min. The portion of the specimen available for transmission microscopy surrounds the hole, as is seen by the dashed lines in Fig. l(b). Slight electroetch-ing accompanying electropolishing reveals the mi-crostructure, as seen in Fig. 3(a) by light microscopy. Low-magnification electron microscopy, as in Fig. 3(b), enables the same areas and grains to be viewed and identified when subsequently examined at high magnification. Fig. 4 is a typical structure of

Jan 1, 1963

By R. W. Guard

ALTHOUGH etching techniques have been developed for revealing dislocation sites in several metals and ionic crystals,h t is valuable to extend the technique to new metals. An etch pit method for nickel has been developed on the basis some suggestions of Dr. John R. Cuthill of the National Bureau of Standards who had observed etch pits in creep specimens of nickel. The etchant used was proposed first by wensch2 for revealing grain size in nickel. The present paper describes the evidence that the technique can be used to reveal dislocations and gives the conditions under which etching can be carried out. The specimens examined were vacuum melted high-purity Ni (99.985 pct Ni) and commercial "A" nickel (99.8 pct Ni). Both materials contained greater than 0.008 pet C and had been annealed in nitrogen or dry hydrogen at 1100o to 1200°C. This gave a grain size of 1.5 mm in the high-purity nickel and 0.050 mm in "A" nickel. Tensile specimens (0.254 in. diam) were deformed from 0.25 to 10 pct at room temperature and then heated for 1/2 hr at different temperatures from 400" to 900°C. The specimens were sectioned longitudinally then polished electrolytically in 60 pct H2SO4 and etched in 35 pct H3PO4 solution at 0.2 to 0.4 v for 30 sec to 3 min. The best method for setting the proper voltage for etching is to increase the voltage until gas bubbles are evolved vigorously from the specimen and then cut it back by 10 pct. It is necessary to heat the specimen above 500°C after deformation in order that etch pits will be formed. This "decoration" treatment permits carbon to segregate to the dislocation rendering them sensitive to etching. It was demonstrated that carbon was the decorating impurity by decarburizing some specimens in wet H2 at 1200°C. The susceptibility to etch pitting was lost following this treatment but could be restored by carburizing in contact with graphite. Some rearrangement of the dislocations in the as-deformed structure occurs on heating at 500oC and above so that the technique can not be used to study the nature of dislocation patterns in deformed specimens. Extended etching does not change the number of pits although the background becomes rough and the pits quite large. The polycrystalline specimens with various strains were examined after annealing at different temperatures. Typical patterns are shown in Figs. 1 and 2. In the unstrained specimen, Fig. 1, the density of pits is 2.5 X 10&apos; per sq cm. All grains show pits regardless of their orientation although there is a

Jan 1, 1961

By R. J. Hopkins, L. B. Haney

On the basis of limited experimental work conducted at the Port Pirie smelter, it would appear that, by increasing the specific surface of sinter, and possibly that of coke as well, a marked increase in the rate and degree of sinter reduction in the furnace shaft can be achieved. Fusion-point tests have shown that this increased reduction means a much higher sinter fusion point and narrower plastic zone, while the more efficient utilization of coke in the furnace is inherent in the intensification of reduction by the provision of a more reactive sinter surface. Investigations aimed at increasing the ability to operate the blast furnace with a higher lead tenor of sinter reducing fuel cost proportionately, and at eliminating the loss in reduction potential in coke entering the furnace, as shown by the presence of appreciable proportions of CO in the top gases, are reported. Several lines for future investigations that could result in improved smelting methods are proposed. A SOMEWHAT informal presentation of ideas on lead blast-furnace smelting will be given in this paper. These ideas have been developed during observations of furnace behavior at Port Pirie and earlier at Mt. Isa, and have been guided by the results of laboratory experiments at Port Pirie. The authors do not intend to propound any particularly new theories, but present their ideas as a basis for discussion which may help toward a better understanding and improved control of blast-furnace operation. Performance variations of considerable magnitude occur from time to time at most lead blast-furnace plants. While Port Pirie is fortunate in having a very regular supply of high grade concentrates, it is no exception in this respect. Such irregularities are of considerable economic importance and they constitute a challenge to present-day metallurgists in their efforts to obtain an ever greater degree of control over furnace operation. In operating as Port Pirie does with a relatively high lead charge, it has been recognized for a long time that shaft conditions are ,of the greatest importance. A practical, or engineering, attack on the problem of accretions consisted of changes in furnace design, e.g., by widening the shaft to 10 ft above the bottom row of tuyeres, and by the provision of curved ends and vertical walls.&apos; That this attack has had a great measure of success is shown by the fact that barring down of these wide furnaces is rarely necessary, shaft conditions have greatly improved, and sensitivity to charge variations has been markedly reduced. These modifications, followed by some metallurgical changes (chiefly the incorporation of pig iron into the furnace charge in 1948), have brought furnace operation to a point where some variables which were previously masked can now be studied. Accordingly, over different periods of time during the last five years, such variables as could be given numerical values have been recorded and subjected to statistical examination. The objectives of this work were: 1—to reveal the true importance of the different variables and 2—to show the proportion of total furnace variation which is unexplained and therefore referable to causes not measured at present? e.g., shaft accretions, sinter structure, coke structure, and others. Statistical Study of Variables In this work factors relating to furnace speed and lead reduction have been examined: 1—slag com-

Jan 1, 1955

By F. E. Bedale

STUDY of several severe mine explosions that occurred during the winter of 1907 led to the belief that coal dust was a definite explosion hazard. The Consolidation Coal Co. was a pioneer in the early work to&apos; eliminate this hazard and to combat the dangers incident to poor ventilation and the presence of methane. Maintenance of high humidity throughout the mines was one of the first measures adopted, later to be superseded by rock-dusting. In the twenty years from 1907 on, many safety measures were developed and adopted, and several prizes were won, though the practice was crude by present-day standards. But in 1927, the company went to work in earnest, and organized a Department of Safety with adequate personnel and with authority to enforce all approved rules for the prevention of accidents and the preservation of company property. All plans for new construction work, changes in mining systems, and proposals for the purchase of new mining equipment had to receive the approval of this Department. A set of operating- and safety standards was written to govern the activities of all employees, and physical examinations for them were required.

Jan 1, 1938

By T. A. Wright

THE-Institute of Metals Division opened on Tuesday afternoon with Wheeler P. Davey as chairman and G. E. Edmunds as vice-chairman. Four papers were on the program, two being of a fundamental character. A paper on "Internal Surface in Minerals and Metals," by R. S. Dean and J. Roster, was presented by the latter; C. H. Gottschalk discussed coercive forces in powders. In answer to a question by the chairman. The author stated that he had not investigated [he temperature coefficient of resistance. A paper on "Recrystallization and Grain Growth in Cold Worked Polycrystalline Metals," by L. W. Eastwood, Arthur E. Bousu, &apos;and C. T. Eddy, was presented by Mr. Eastwood. A. great many quantitative data were given, with little reference to the theory. Theoretical considerations were discussed by Dr. Gottschalk, and C. A. Edwards of the University College of Wales, contributed very interesting comment on the relationship of size and critical strain. Dr. Edwards discussed the necessity of considering strain with time and temperature.

Jan 1, 1935

By AIME AIME

I N JUNE, 1918, at a meeting of the American Society of Mechanical Engineers in Worcester, Mass;, a resolution was adopted for a committee to investigate the aims and organization of that society. This was followed subsequently by similar independent action on the part of the Society of Civil Engineers. The other two Founder Societies were approached and requested to appoint similar committees, the four committees to combine as a .Joint Development Committee, later called the Joint Conference Committee, to investigate what might be done in the way of coordinating those activities of the Founder Societies which ape of common interest, and which were then being pursued separately. The Joint Conference committee worked diligently -for almost. two years and. brought forth a tentative as outlined in its report which was published in full in MINING AND. METALLURGY, December, 1919. It recommended the formation of a nation-wide organization to be composed of representatives&apos; of all of -the engineering societies, local, state, regional, or national, the object to be to further the interest of the public through the use of technical knowledge and engineering experience, and to consider and act upon matters common to the engineering and allied technical professions. Whereas the technical societies have large fields of endeavor in welfare work, and their prime. efforts are &apos;still in technical lines, this new organization was to be devoted entirely to service, looking to the welfare of the nation and the engineering profession, and to service for the public in local and state affairs.

Jan 1, 1920