Search Documents

By John D. Ridge

For mining geologists, the most important trends during 1962 have been the increased concentration of the exploratory activities of American mining companies in the United States and Canada and the greater use of the combined techniques of geology, geophysics and geochemistry in searches over larger areas for wider varieties of metals and minerals. The principal reasons for these changes in approach have been the deterioration of the political-economic climate in many areas of the globe of equal or greater geologic promise and the realization that modern exploration is most efficiently and economically conducted through the use of all available means of detecting ores in areas sufficiently large to raise to a maximum the chances of success. The attitude of certain major U.S. metal-producing companies can be shown by the officially ex- pressed positions of their principal officers. Early in 1962, Clyde E. Weed, Chairman of the Board of Anaconda, remarked that "because of unsettled conditions and disruptive influences in many of the copper-producing areas of the world, it is imperative that domestic copper-producing capacity be improved and made as efficient as possible in order to meet consumer demands at reasonably stable prices." In November, Robert G. Page, President of Phelps Dodge, pointed out that his company is not only concentrating most of its exploratory effort on this continent but is also increasing the number of metals for which it is searching. Frank R. Milliken, President of Kennecott, recently said that "most of our exploration money is going into the northern part of the Western Hemisphere."

Jan 2, 1963

By Evan Just

Throughout history mining operations have, been relatively technical in character and somewhat esoteric. In ancient times mines were places where prisoners of war or criminals were sent, to drag out short lives of hard labor, under conditions ranging from hazardous to lethal. Underground mines were damp and poorly lighted, and workers were often cramped in narrow spaces and tiresome positions. Hard rock was mined by building fires against faces and quenching with water. Combustion products from these fires and from such dim torches as were provided, plus the dampness, made the underground atmospheres quite injurious to health. During the Middle Ages, mining became less penitential and more technical. Because of the desire of sovereigns to foster production from mines, miners enjoyed special privileges as free men. Crude pumping, hoisting, and ventilation systems were introduced (Fig. 9.1). However, mining remained a relatively hardworking, hazardous occupation, separated from the lives and comprehensions of most people. With the Industrial Revolution, steam-powered pumps enabled penetration to greater depths, and the use of power-driven machinery gradually revolutionized productivity. Skill became more important than back-breaking labor. This revolution continues into the present. Mining today uses some of the largest and most complicated machinery in existence and little rock is moved by direct labor. Power drills, explosives, and boring machines penetrate and break hard rock. The modern mine, surface or underground, presents an impressive panoply of drilling, breaking, loading, and transporting equipment, facilities for power transmission, pumping, and ventilation, and expensive, complicated crushing and treatment machinery. Modern technology, machinery, and skilled workmen produce an efficiency that knows no parallel in the raw material field. Mineral substances are extracted and converted into useful forms at costs which are dwarfed by those of providing forest or agricultural products in terms of comparable weights, even though conversion of these last categories is typically much simpler. Capital investment per worker, i.e., mechanization, is greater than in nearly all other industries. Despite these features, and more than average financial risk, the mineral industries perform at modest profit. The popular concept that mines and oil fields are sources of boundless rewards is a myth, sustained by the occasional unusual episode. Before one can start actual production of minerals, he must first acquire a suitable deposit. The process of acquisition will require anything from a rather simple search to a difficult, lengthy, expensive exploration effort. After locating the desired deposit, title must be obtained by denouncement, concession, leasing, or purchase. If the deposit is solid, it can be mined in pits or underground workings. If fluid or easily fusible, it can be produced through wells. If dissolved in lake or seawater, it can be

Jan 1, 1976

By T. E. Godson

AS this is the age of reform, a uniform mining law for North America is a moot subject for discussion at this meeting of the Institute. The question is one of peculiarly technical and, in many respects, local character. We all appreciate the value of the metal-producing industries and recognize the necessity and importance of a well-considered and evenly balanced mining law as a branch of our jurisprudence either for the Provinces or the Dominion as a whole. Mining has taken its place as a forempst industry and legislation that seeks to control and govern it is the concern of not only the active miner but the citizens of the state. A law that, through its charitable measures brings into being the prospector, the pathfinder and superstructure of all mining activity and industry! protects his interests, safeguards invested capital, and encourages and enforces development, possesses at least the salient requirements of a businesslike Act. The manner of doing so is, I think, one of local and internal concern. May I be permitted to say without presumption that of the five mining codes, or Acts, that we have in the Dominion of Canada born and bred within the Provinces of British Columbia, Ontario, Quebec, New Brunswick, and Nova Scotia, some of them could be materially improved. In many respects they do not measure up to the times; they were no -doubt creations of merit at the date of their .birth but they have not been clothed in seasonable raiment as the years passed by. It is a stern fundamental principle that all natural resources are the inalienable property of the crown. If it is mineral land, then it follows for the protection of the state and the direct advancement of the occupant that the land should be developed as such. The method or machincry by which this must be accomplished is a matter of detail, not of principle. If the right to possession as a licensee depends on discovery, it is not inconsistent with the duty the crown owes to the state that a grant in fee should pass to the discoverer if there is imposed, after patent issues, a requirement of continuous work or the alternative of an acreage tax sufficiently burdensome to make it unprofitable that the land should be held in an undeveloped state. If this requirement is recognized, the mental distinction between a grant and lease ceases to exist. A

Jan 1, 1920

By R. W. Moore, A. B. Kinzel

Although the iron-carbon diagram has undergone many changes in the last 20 years, the region below the eutectoid line and up to approximately 1.7 per cent carbon has been little affected. This region is generally considered to consist of cenlentite and ferrite. Graphite has been noted occasionally in the hypereutectoid steel region, and the ready formation of graphite nodules in malleable cast iron is a phenomenon difficult to interpret in the light of cementite, supposedly stable at sub-eutectoid temperatures. In this case the graphite formation has been partly explained by the presence of silicon, and many have believed that silicon acts to change the stable state rather than to accelerate reactions so as to arrive at the stable state in a briefer period of time. Consideration of this phenomenon indicates that cementite is not the stable phase in the temperature composition zone referred to. In the course of examining a low-carbon steel tube taken from a petroleum cracking still, which had been in service for approximately three years at temperatures somewhat below the eutectoid temperature, observations were made that shed light on this entire subject. The tube in question analyzed:' C, 0.15 per cent; Mn, 0.49; Si, 0.02; S, 0.023; P, 0.015. The microstructure of the tube after service is shown In Figs. 1 and 2. From these it is evident that cementite as such is absent, and that in its place nodular graphite has been formed. In order to check this observation further, samples taken from the tube were heated at 850" C. for varying periods of time. The small samples were put into a large hot furnace, and the total time is recorded. The structure of the sample after 5 min. at 850" C. is shown in Figs. 3 and 4, and the nest of pearlite surrounding the graphite nodules is most satisfactory evidence of the character of the nodules. As the length of time of heating at this temperature increases, the pearlitic zone increases, with final restoration

Jan 1, 1935

By R. W. Moore, A. B. Kinzel

Although the iron-carbon diagram has undergone many changes in the last 20 years, the region below the eutectoid line and up to approximately 1.7 per cent carbon has been little affected. This region is generally considered to consist of cenlentite and ferrite. Graphite has been noted occasionally in the hypereutectoid steel region, and the ready formation of graphite nodules in malleable cast iron is a phenomenon difficult to interpret in the light of cementite, supposedly stable at sub-eutectoid temperatures. In this case the graphite formation has been partly explained by the presence of silicon, and many have believed that silicon acts to change the stable state rather than to accelerate reactions so as to arrive at the stable state in a briefer period of time. Consideration of this phenomenon indicates that cementite is not the stable phase in the temperature composition zone referred to. In the course of examining a low-carbon steel tube taken from a petroleum cracking still, which had been in service for approximately three years at temperatures somewhat below the eutectoid temperature, observations were made that shed light on this entire subject. The tube in question analyzed:' C, 0.15 per cent; Mn, 0.49; Si, 0.02; S, 0.023; P, 0.015. The microstructure of the tube after service is shown In Figs. 1 and 2. From these it is evident that cementite as such is absent, and that in its place nodular graphite has been formed. In order to check this observation further, samples taken from the tube were heated at 850" C. for varying periods of time. The small samples were put into a large hot furnace, and the total time is recorded. The structure of the sample after 5 min. at 850" C. is shown in Figs. 3 and 4, and the nest of pearlite surrounding the graphite nodules is most satisfactory evidence of the character of the nodules. As the length of time of heating at this temperature increases, the pearlitic zone increases, with final restoration

Jan 1, 1935

By R. Norman Orava

The strain-mte behavior of. the tensile yielding and flow characteristics of arc-cast polycrystal-line molyhdenum of pidrity > 99.97 pct was investigated in the range 10-6 to 10-1 sec-1 at 243o, 293o, and 373oK for two grain sizes, 0.027 and 9.098 mm. For 0.998 mm, the strain-mte dependence of the lower yield stress can be described by a straight line of the jowl a, = a + 0 log e over the whole range of strain rates examined. However, for 0.027 mm, the data fit several consecutive linear relationships of the above form. The previous association of these different linear regions with different rate -controlling mechanisms is questionable for molyhdenzdm. The senlilog strain-rate dependence of the yield stress is consistent with Hahn's model for yielding when the stress dependence of the mobile dislocation density, pr, is taken into account. Since p', from rate -cycling experirnents, is found to be relatively insensitive to stress for single crystaIs, the obserzied log-log dependence of their yield stresses is also in agreement with the model. A correction for the stress dependence of p' changes the activation oolurrze for yielding from a zero to a more realislic inverse function of stress where the Peierls mechanism is believed to be rate-controlling. The gmin-size dependence of the lower yield stress is not a monotonic junction of strain rate. RECENT experimental evidence' has revealed that the strain-rate dependence of the tensile lower yield stress, a,, of commercially pure ni- obium and tantalum tested at room temperature can be described by several consecutive semilog relations of the form: sv =a + ß log € [1] where i is the applied strain rate and a and 0 are constant Over only relatively small ranges of strain rate. Three linear regions were found for niobium and four for tantalum. Each linear region was interpreted as being associated with a different rate-controlling mechanism on the basis of the current

Jan 1, 1964

By L. W. McKeehan

The occurrence of twins in large ferrite crystals, made by a new process, was reported in a recent note.' This paper describes a typical case of such twinning and suggests, on the basis of the observed facts, why smooth slip-planes are rarely observed in this metal. Method of Preparation The material in which the crystals here dealt with were grown was made from 1/8in. Armco iron welding rod containing C, 0.04; S, 0.037; P, 0.003; Si, 0.008, and Mn, 0.02 per cent. This rod was cold drawn into wire about 1 mm. dia. A piece of this wire was supported vertically and was locally heated in hydrogen at atmospheric pressure to about 1400" C. by an alternating current (60 cycles per sec.) of about 35 amp., passed through it between a pair of traveling contacts about 8 cm. apart. The rate of travel for the case in hand was 12 cm. per hr. After some 30 cm. of the length of the wire had been heated and cooled in this manner the whole wire was immersed for a few seconds in dilute nitric acid, not restrained by alcohol. Etching was continued until, as nearly as could be judged by eye, the original smooth cylindrical surface of the wire was no longer capable of specular reflection. Measurements The wire in the etched state was next mounted in a goniometer of special form which allowed the measurement of the spherical coordinates of the normals to any plane surfaces left by the etching. These coordinates were most conveniently a polar distance, 8, from one direction of the wire axis, and an azimuth or longitude, ?, from an arbitrary prime meridian. The region to be described more particularly is shown at a low magnification in Fig. 1, which gives two different views, differently illuminated to show the spatial relationship of a crystal occupying most of the part shown and of an inclusion, or rather a series of three inclusions suspected of being twins based on the principal crystal.

By L. W. McKeehan

THE occurrence of twins in large ferrite crystals, made by a new process, was reported in a recent note.1 This paper describes a typical case of such twinning and suggests, on the basis of the observed facts, why smooth slip-planes are rarely observed in this metal. METHOD OF PREPARATION The material in. which the crystals here dealt with were grown was made from 1/8-in. Armco iron welding rod containing C, 0.04; S, 0.037; P, 0.003; Si, 0.008, and Mn, 0.02 per cent. This rod was cold drawn into wire about 1 mm. dia. A piece of this wire was supported vertically and was locally heated in hydrogen at atmospheric pressure to about 1400° C. by an alternating current (60 cycles per sec.) of about 35 amp., passed through it between a pair of traveling contacts about 8 cm. apart. The rate of travel for the case in hand was 12 cm. per hr. After some 30 cm. of the length of the wire had been heated and cooled in this manner the whole wire was immersed for a few seconds in dilute nitric acid, not restrained by alcohol. Etching was continued until, ass nearly as could be judged by eye, the original smooth cylindrical surface of the wire was no longer capable of specular reflection. MEASUREMENTS The wire in the etched state was next mounted in a goniometer of special form which allowed the measurement of the spherical coordinates of the normals to any plane surfaces left by the etching. These coordinates were most conveniently a polar distance, ?, from one direction of the wire axis, and an azimuth or longitude, [ø], from an arbitrary prime meridian. The region to be described more particularly is shown at a low magnification in Fig. 1, which gives two different views, differently illuminated to show the spatial relationship of a crystal occupying most. of the part shown and of an inclusion, or rather a series of three inclusions suspected of being twins based on the principal crystal.

Jan 1, 1928

By John Fulton

Early in the year 1875, some difficulty was experienced in the " Old blast-furnaces " of the Cambria Iron Company, at Johnstown, Pennsylvania, arising from the increased use of native coke, prepared in Belgian ovens near the furnaces, in mixture with Connellsville coke, in the production of Bessemer pig-iron. This was the more surprising at that time, because a very caulplete coal-crushing and washing apparatus, after the Bradford plan, had just been put into successful operation, affording a pure coal for coke-making. It was confidently expected that this thorough cleansing of the coal would improve the quality of the coke and fit it for the increasing manufacture of Bessemer pig-iron. But the trouble with the native coke continued. Experiments in fuel charges-increasing and reducing them—failed to correct the irregular working of these furnaces. Increasing the charge of native coke produced abnormal heat at the top of the furnace, reducing it cooled the furnace below. At this stage of affairs, the Hon. Daniel J. Morrell, general manager of the Cambria Iron Company, requested the writer to make the requisite investigation to determine the nature of this coke-difficulty, and to ascertain why the Johnstown coke could not be used in blastfurnace work as well as Connellsville. This task at first did not appear to present any special difficulties, but subsequently it expanded into proportions that caused no little anxiety. The first effort was directed to procuring average samples of Johnstown and Connellsville coke. At this period of the investigation, it was assumed that the whole matter could be intelligently solved by comparing the chemical analyses of the two cokes: Johnstown Coke. Connellsville Coke. Moisture,.......... 0.30 Volatile matter,......... 0.46 Fixed carbon,.90.48 89.57 Ash,.8.96 9.11 Sulphur,.0.56 0.82 Phosphorus,..... 0.014 100.00 100.274 Analysts, T. T. Morrell. A. S. McCreath.

Jan 1, 1884

By Linn Bradley

F. H. WILLCOX, Pittsburgh, Pa. (communication to the Secretary*). -We must keep in mind, in balancing the savings-to be anticipated by the most efficient combustion of gas, the best heat absorption by stoves or boilers, and by heat conservation of the thermal equivalent carried in. blast-furnace gas-against the cost in operation, maintenance, depreciation and interest charges of the equipment required to realize the savings, that in boilers and hot-blast stoves we are basing our economies upon two different, combustion phenomena. In a boiler, evaporating water at a heat efficiency of 70 per cent., approximately 47,550 B.t.u. is consumed per boiler horsepower. Taking the blast, furnace gas cited in the above paper, we are using about 38 ¾ lb. of cold-washed gas per boiler horsepower. Using the hot-cleaned gas, the same equivalent heat is furnished by 34 1b. of the gas , This leaves of the 38 ¾ lb. required in the case of cold-washed gas, 4 ¾ lb. or 6,650 B.t.u. available for raising more steam when dry-hot gas is used, which means that an equivalent amount of coal firing can be dispensed with. Per ton of iron, this figure 2/3 X 12,000/38.75 X 4.75 = 980 lb. gas or 1,372,000 B.t.u. or 100 lb. coal. At $1.50 per ton of coal, the net saving per ton of pig iron produced by the use of dry-hot over wet-cold cleaning will, therefore, be about $0.06 2/3. At a stove heating 8,500 lb. of air per toil iron from 150° F., one-quarter of the dry-hot cleaned gas, or 3,000 lb., would heat the air to 1,450° F. 3,000 X 1,400 X 0.70 = (8,500 X 0.255) = 1,300. The cold-wet gas would heat the same amount of air to 1,280° F. 3,000 X 1,225 X 0.70 = (8,500 X.0.255) = 1,130.

Jan 4, 1917

THE following statement is contained in an article entitled "Mortgaging the Future." by Walter C. Teagle, president of the Standard Oil Co. of New Jer-sey, appearing in the current issue of the Lamp, the official organ of the Standard Oil Co.: "During the last eight months the domestic daily production. of crude oil has risen 300,000 bbl.. which means that no less a volume than 2,500,000 bbl. now are coming to market each day. . . . Every twenty-four hours 250,000 bbl. more than the consumer required are being added to our surplus oil storage. The temporary advantage of cheap petroleum products and the availability of fuel .oil, for a widespread use as a substitute for coal are not being weighed against the time when scarcity may follow on the heels of plenty and the public of tomor-row may have to pay for today's excesses. The over-production of crude and its consequences constitute a problem of national import which far outweighs the temporary advantages either to a part of the industry or to sections of the public.

Jan 8, 1927

By Charles R. Simcoe

The stress-strain curves in the microyield region for various Fe-C solid solutions shown by Davies and Ku are typical examples of parabolic curves defined by the expression a = kEn 111 These data, when replotted on log-log coordinates, as shown in Fig. 9, exhibit three essentially parallel straight lines. It is apparent that carbon increases the flow stresses, but does not affect the exponent n. In other words, the only factor in Eq. [1] affected by in in carbon content is the constant k. As Eq. [1] is written k is the stress at a strain of 1.0. This is unsatisfactory for examining data in the microyield region. Therefore, the equation can be altered to the form: to permit the use of the authors' microyield stress at a strain of 10-6 as k. Extrapolating the curves in Fig. 9 to a strain of 10-6 gives stress values of 2000, 3200, and 5400 psi for 0.008, 0.014, and 0.02 pct C, respectively. These values do not agree exactly with the authors' measured values, but this will not affect the following discussion. The effect of carbon content on the slopes of the stress-strain curves shown in Fig. 2 of the paper by Davies and Ku can be analyzed by differentiating Eq. [2] with respect to strain. Thus: where n is always less than 1.0. Since n is essen- tially constant as a function of carbon content for the data under discussion, the slopes of the stress-strain curves depend only on k and E. If the slopes are examined at various selected Plastic strains. i.e., 10-6, 10-5, and so forth, it follows from Eq. [3] that the dif-ferent slopes for the different carbon contents depend only on the different values of ke=10-6. Thus, the larger ke=10-6, the steeper the linear stress-strain curve will rise with increasing plastic strain. This

Jan 1, 1969

Jan 1, 1923

By Pei-Yung Huang, C. R. Hayward

In order to understand more fully the actual state of copper lost in copper reverberatory slags, a systematic study on the various reactions between certain metallurgically important copper compounds and synthetic copper reverberatory slags was undertaken by the authors in the Massachusetts Institute of Technology from 1942 to 1945.1 This paper, being only a part of the work completed, is published first because it furnishes the first experimental evidence of the formation of copper ferrite from reactions between cuprous oxide and copper reverberatory slags. Choice of Slag Composition The choice of the composition of the synthetic reverberatory slags to be used was much deliberated. Commercial copper reverberatory slags, neglecting minor constituents, avcrage :2,3 45 to 47 pct FeO; 38 to 42 pct SiO2; 5 to 6 pct CaO; 5 to 6 pct A12O3. Since the ternary system CaO-FeO-SiO2 has been much more thoroughly studied4 and is much simpler than the quaternary system CaO-FeO-SiO2-Al2O3, it was decided to use calcium oxide only instead of calcium oxide and alumina in the synthesis of the slags. Fortunately the composition of the average copper reverberatory slag with calcium oxide substituted for alumina lies in the region of the phase diagram clarified by the investigators. A survey of the phase diagram (Fig I) suggested two compositions: (I) the composition near the invariant point S, which is made up of 46 pct ferrous oxide, 37 pct silica and 17 pct calcium oxide; (2) the composition near the invariant point K with 45.5 pct ferrous oxide, 43 pct silica and 11.5 pct calcium oxide. Composition S has the advantage that the percentages of ferrous oxide and of silica almost exactly coincide with those of the average reverberatory slags, and that of the lowest melting point (1093º ± 3ºC) in the whole ternary system. The calcium oxide content, however, obviously is high. Since we have already substituted calcium oxide for alumina, and since calcium oxide is more basic than alumina, the fulfil- slag is decidedly too basic. Composition K has a slightly higher melting point (1150O + 3OC) and a higher silica content, but this is preferred because the slag is saturated with respect to tri-dymite and thus should not corrode siliceous refractories. Besides, it is less basic than composition S. The filial slag composition, therefore, was chosen to

Jan 1, 1949

By W. O. Philbrook, R. H. Spitzer, F. S. Manning

A generalized mathematical model has been developed to describe the kinetics of the gaseous, topo-chemical reduction of porous hematite spheres. Gas-solid reduction is permitted at each of three advancing interfaces and is controlled by a complex series-parallel sequence of chemical and transport steps. Despite the fact that transport resistances are significant to the advance of each interface, little deviation from linear advance is predicted for the first 98 pct of reduction. Calculations to predict the movement of magnetite /wustite interface by a solid-state diffusion mechanism have been incorporated into the earlier dense-pellet model.' The porous-pellet model is found to give a better description than the dense-pellet one for McKewan's measurements2 of interface movements in dense polycrystalline hematite reduced in hydrogen-water vapor mixtures. THIS paper reports a continuation of work"3" directed toward the better understanding of gas-solid reactions and the development of mathematical models that may be helpful in the design or control of ore-reduction processes. Laboratory studies of the reduction of single oxide samples in tube furnaces normally employ an abundant excess of pure reducing gas. Reduction may appear to be adequately described by a model assuming gas-solid reaction solely at the iron/wustite interface.''' However, when iron ore is reduced in either a fixed bed or an efficiently operated counter-current column, there are portions of the bed where the partially spent gas is no longer capable of reducing wustite to iron. Nevertheless, the formation of the intermediate reaction products, wustite or magnetite, can and does continue. In order to account for this aspect of the reduction of beds of particles, three semiempirical mathematical models were devised.' One of these was for the limiting case of completely dense particles, and two alternatives were provided for porous particles. For purposes of the analysis, a dense pellet was defined as one in which the wustite and magnetite layers were impervious to the reducing gas when the atmosphere was capable of forming iron. In a porous pellet, the intermediate product layers were assumed to be sufficiently permeable to allow reducing gas to penetrate beyond the iron/wustite interface to form wustite and magnetite by removal of oxygen as a gaseous product rather than by a solid-state redfiction mechanism. Further progress required a better understanding of the reaction of the individual particles with the gas stream. A comprehensive mathematical treatment was developed' to describe the continually changing interplay of transport and reaction steps

Jan 1, 1967

FRIENDS of the late Charles F. Rand presented in 1930 a sum of money from which the income is available to support various phases of the work of the Institute in which Mr. Rand was so deeply interested. At present the fund amounts to $10,400. The specific terms of the deed of gift are as follows: "The fund collected to establish a memorial to the late Charles F. Rand shall be placed in the custody of the Board of Directors of the American Institute of Mining and Metallurgical Engineers, to be set up as a trust to be known as the `Charles F. Rand Foundation,' the income of which shall each year be applied to a distinct purpose to be decided upon in that year by vote of the Board of Directors. This purpose shall be such as to promote the general welfare of the Institute and to constitute a permanent memorial of the usefulness of Mr. Rand, who for many years gave unstintingly of his time and talents in its service. "It shall be within the discretion of the Board of Directors to establish a medal to be known as the Charles F. Rand Memorial Medal to be awarded at such a time and under such rules as may be determined by the Board of Directors, for Distinguished Achievement in Mining Administration." The establishment of this medal was announced at the annual meeting in February, 1932, the term "mining" being defined in its broad sense to include metallurgy and petroleum. Robert Linton is chairman of the Charles F. Rand Foundation Award Committee.

Jan 1, 1943

By R. L. Fleischer, B. Chalmers

In order to observe size effects associated with a grain boundary, aluminum single crystals and bicrystals of various cross-sectional dimensions were deformed in tension. Typical stress-strain curves are presented in conjunction with measurements of the effects of changes in crystal dimensions. Some effects of the growth rate used in preparation of crystals are also described. It is indicated that the macroscopic constraints at a grain boundary are responsible for the most prominent grain-boundary effect, the production of multiple slip. Two measurements of the width of the region of double slip are in agreement. It is concluded that the yield stress of aluminum is affected markedly by the inherent oxide coating. THE general problem to be examined is that of dimensional effects in the plastic deformation of metal crystals. These effects will be termed "size effects" and are here defined as follows: A size effect occurs in a series of crystals if their plastic-deformation properties are a function of crystal dimensions. Clearly then size effects depend on the nature of the boundary conditions imposed on the crystal. Crystal boundaries can be of three types: interphase, inter-crystalline, and free surface. Such deformation effects as are caused by distribution of phases, grain size, lineage structure, and single crystal external geometry are specific types of size effects. This discussion will be confined primarily to grain-boundary and single-crystal size effects, though in practice most "single crystals" not only have a number of small angle boundaries but also have one or more surface phases, so that the boundary conditions appropriate to a free surface do not necessarily apply. Hence, to this extent interphase size effects will be considered. The question of size effects associated with grain boundaries (called here intercrystalline size effects)

Jan 1, 1959

By C. E. Brown, D. C. Helms, O. W. Shimer

The early history and progress of anthracite stripping, from the first known operation at Summit Hill in 1821 through 1917, was covered in 1917 in a paper by J. B. Warriner,1 then chief engineer, now president of the Lehigh Navigation Coal Co., and stripping methods between 1917 and 1931 were the subject of a paper in 1931 by H. H. Otto,2 of the Hudson Coal Company. . The present paper is confined to methods used today on pitching beds in the western middle and southern anthracite fields. The anthracite industry, not unlike other large industries, had been affected for more than a decade by the adverse economic conditions of the country. High development and operating costs and the competition of other fuels caused some collieries to be closed temporarily, while others were permanently abandoned. In order to obtain a larger tonnage at a lower development cost, a larger stripping program was put into effect by many companies. In 1932, stripping operations accounted for 3½ million tons, or 7 per cent of the total anthracite production of the year, and in the next 10 years this increased until more than double that amount, or over 14 per cent of the total production, was from stripping operations. These figures represent the total production of the entire anthracite region; unfortunately, the figures have not been separated from the different fields. There are some operations in the southern and middle western fields where the tonnage obtained from stripping amounts to more than 30 per cent of the total colliery production. Stripping operations on pitching beds present difficult problems. Owing to the various geological formations, a different situation is encountered in nearly every stripping pit; and because of the proximity of an overlying bed, it is very often necessary to load the entire overburden into trucks and haul it out of the pit to the dump area, although back filling and casting is done whenever possible. Beds in the areas described in this paper pitch from 20" to 90 and some are on the invert in many sharp folds and faults. Planning The more successful strippings have had adequate engineering analysis. Some work is being done without much preliminary planning, but many strippings would have failed completely if close supervision by the engineering department had not been . maintained. Locations of stripping areas are determined as follows: I. By constructing cross sections over the areas and drilling sufficient diamond-drill or well drill holes to study the strata and to determine the location, thickness

Jan 1, 1944

By H. W. Paxton, C. C. Busby

IT has been shown previously' that strain aging can markedly improve the tensile properties of low carbon martensites, especially the yield-tensile ratio, without seriously affecting the ductility. In view of interest in high strength steels, an investigation has been made of the effect of strain aging following tension or rolling on the tensile properties of A1S1 4340 in an attempt to obtain a tensile

Jan 1, 1957

By S. S. Clarke

LATE in 1942, the increasing demand for zinc, coupled with the growing shortage of miners and the knowledge that some abandoned mines would have to be reopened for prospecting and development, led to considerable thought as to the possibilities of further mechanization in order to conserve man power. The ore bodies, locally termed "sheet ground," are an important ore bed in some mines and are in the lower part of Boone formation of the Mississippian Series. Some mines contain interbedded layers of nearly pure galena and sphalerite in horizontal sheets ranging in thickness from a thin seam to several inches and is persistent over large areas. This type of ore body offered the best opportunity for study and experiments. The use of jumbo drill carriers was advanced but some doubt was expressed as to the adaptability of jumbos as then in use to mine headings as compared to post and arm mounting (Fig I). Another consideration was the introduction of truck haulage when several mines were trackless. A drill frame, built to carry 2 4-in. drifters, was mounted on a truck chassis. This design proved a failure as it was not rigid and the resiliency of the tires and springs allowed too much play. Long screw jacks were then used to hold the truck firmly in place, but placing the jacks and securing the truck required more effort and time than setting up post drills, so the truck carrier was abandoned. The use of a bull dozer underground had been under consideration for some time to be used in "brunoing" the broken dirt from behind pillars and other inaccessable places so the slusher drags could load without double dragging the dirt. A dozer with hydraulic blade lift was purchased and R. I. Tuthill, Superintendent of Section 30 Mines, suggested that a long drill arm be substituted for the blade, and the drills mounted on the cross member. The hydraulic lift would permit drilling holes at any required spacing. The "cat" was very mobile and answered the problem of a trackless mine. The initial tests showed that the "cat" would make a good carrier, but the hydraulic controls Were not positive enough to keep the drills in alignment while drilling. The next step was to build a small hoist. This hoist was attached to the power take-off on the "cat" and by means of sheaves and a double line of 3/8-in. hoist cable, a positive control for raising and lowering the boom was obtained. To avoid serious injuries to the drillers should the cable break, a safety chain was fastened to the drill boom and hooked into a slot in the back of the "cat" frame. A different power unit was obtained for the "cat," as a state law prohibited the use of internal combustion engines in mines. A custom machine shop had just placed on the market a small hoist powered by a Model A Ford engine that had been very ingeniously converted to a slide valve engine using compressed air. To use this unit on a "cat," our master mechanic de-

Jan 1, 1947