Search Documents

Gus C. Henning, New York City: In taking up the discussion of these specifications it is necessary that I give definitions of what I understand under the term " Specifications." There may be three kinds, viz.: (1) Specifications in general; (2) Standard Specifications; (3) Standard International Specifications. 1. A Specification is a document used in commerce which should clearly define the qualities of material to be supplied by the producer, the tests which shall be applied for their determination, and the methods which shall be applied for the purpose of determining that the entire product shall possess such qualities, properties and finish as are desired. The terms used in such document must be applied in accordance with their strict technical definitions as used by those most conversant with them, and the language should be of such accuracy that there can be but a single interpretation of each and every clause. A specification is a part of a contract, and should be legally perfect and accurate. Inaccuracy of definition and dic-

Jan 1, 1903

By R. A. Meussner, R. J. Goode

Six intermediate phases occur in the Nb-Zn sysThese phases form by peritectic reactions at 1120°, spectively. The Nb Zn 15 phase appears as the minor phase in the eutectic structure, and the terminal phases remain nearly pure niobium and zinc even at high temperature. Vapor -pressure measurements on the four high-temperature phases (Nb Zn to Nb Zn 3) permitted estimates of the composition limits of these phases and the calculation of approximate values of AFO, AH°, and AS°. 1 HE present study of the constitution of the binary Nb-Zn system was a part of an analysis of the mechanism by which coatings of the Nb-Zn intermediate phases protect niobium against oxidation at high temperature.' Since the primary interest in these phases was in coating service, attention in this study was given principally to the four phases stable at high temperature with only cursory attention to the two low-temperature phases. The solubility studies of niobium in zinc by Martin, Knighton, and Feder2 and the reports from the present study of the Nb-Zn coating represent the only published data pertaining to this system. Previously Hodge, Evans, and Hoskins, in an experimental survey, had noted that niobium was not resistant to attack by molten zinc, but no further observations were reported. EXPERIMENTAL PROCEDURES a) General. The nature of the binary Nb-Zn system precluded the use of more conventional methods of determining the phase equilibria such as thermal analyses of a series of cast alloys. An extrapolation of the liquidus data of Martin, Knighton, and Feder2 to higher temperatures suggested that the solubility of niobium in zinc would remain low in the entire temperature range of interest. The preliminary results of the present studies showed that all of the high-temperature intermediate phases form by peritectic reactions. Thus the sluggish nature of this type of reaction and the steepness of the liquidus indicated that thermal analyses would not yield reliable data. The peritectic reactions, of course, precluded the direct formation of samples of the individual phases from the melt. b) Materials. The niobium and zinc used in the present studies were of high purity. The niobium, in the form of 0.1-in.-diameter rods, contained 30 ppm 0, 30 ppm N, and 15 ppm C. Aside from 0.05 pct Ta, the metallic impurities (iron, titanium,

Jan 1, 1965

By Jos. J. Walsh

Ventilation within a coal mine is essential to the welfare of those employed therein, from the standpoint of health, safety, and efficiency. While the saving of life and the preserving of health are the chief reasons for ventilation, efficiency and production are increased. In spite of the fact that we speak of air as having a certain composition, the proportions of oxygen, nitrogen, and carbon dioxide are not fixed, but vary between small limits. The different elements are not chemically united, they are merely mixed and each is free and can be separated with little energy. For this reason air in the mine workings is seldom found in a pure state. Factors that necessitate ventilation in coal mines are those that change the composition of pure air. Contamination of mine air results from the burning of oil-fed flames, the use of explosives, the oxidation of coal, and the liberation of gases by the coal. The extent to which these factors exist governs the size and general plan of the ventilating applianccs required. An efficient ventilating system is one that will furnish air at the working faces in sufficient volume to dilute and render harmless noxious gases and at the same time maintain an oxygen content closely approaching that of pure air. In a well-ventilated mine, the oxygen seldom falls more than 0.5 per cent. below normal. The carbon-dioxide content of the air in the average coal mine will vary from 0.1 to about 0.8 per cent., which amounts are not harmful. Three per cent. of carbon dioxide in air doubles the frequency and the depth of breathing; it is plainly noticeable and if breathed continuously for several hours its effect would probably be harmful. Slight reductions in the oxygen content of the air, such as occur in well-ventilated mines, have no debilitating effect on the worker. A person not exerting himself would fail to observe any unusual physical effect in an atmosphere: containing 17 per cent. of oxygen. This condition, however, or even a condition showing an oxygen content below 20 per cent., would indicate poor ventilation and that the elements which tend to reduce the efficiency of the worker are present, namely water vapor and a high wet-bulb temperature.

Jan 1, 1923

By Jos. J. Walsh

Ventilation within a coal mine is essential to the welfare of those employed therein, from the standpoint of health, safety, and efficiency. While the saving of life and the preserving of health are the chief reasons for ventilation, efficiency and production are increased. In spite of the fact that we speak of air as having a certain composition, the proportions of oxygen, nitrogen, and carbon dioxide are not fixed, but vary between small limits. The different elements are not chemically united, they are merely mixed and each is free and can be separated with little energy. For this reason air in the mine workings is seldom found in a pure state. Factors that necessitate ventilation in coal mines are those that change the composition of pure air. Contamination of mine air results from the burning of oil-fed flames, the use of explosives, the oxidation of coal, and the liberation of gases by the coal. The extent to which these factors exist governs the size and general plan of the ventilating applianccs required. An efficient ventilating system is one that will furnish air at the working faces in sufficient volume to dilute and render harmless noxious gases and at the same time maintain an oxygen content closely approaching that of pure air. In a well-ventilated mine, the oxygen seldom falls more than 0.5 per cent. below normal. The carbon-dioxide content of the air in the average coal mine will vary from 0.1 to about 0.8 per cent., which amounts are not harmful. Three per cent. of carbon dioxide in air doubles the frequency and the depth of breathing; it is plainly noticeable and if breathed continuously for several hours its effect would probably be harmful. Slight reductions in the oxygen content of the air, such as occur in well-ventilated mines, have no debilitating effect on the worker. A person not exerting himself would fail to observe any unusual physical effect in an atmosphere: containing 17 per cent. of oxygen. This condition, however, or even a condition showing an oxygen content below 20 per cent., would indicate poor ventilation and that the elements which tend to reduce the efficiency of the worker are present, namely water vapor and a high wet-bulb temperature.

Jan 1, 1923

By N. Brown, H. Green

The effect of quenching temperature and of aging temperature and time on compression stress-strain curves of ß brass was investigated. Age softening occurs at a rate which decreases with decrease of quenching temperature below the critical temperature for ordering. The activation energy for softening is 15,400 cal per mol. No matter how rapidly brass is quenched or what the temperature from which it is quenched, practically complete order is obtained at room temperature. It has been demonstrated that with respect to the specific heat,',' electrical resistivity," X-ray diffraction, and microstructure, the slowly cooled and rapidly quenched specimens are the same and that complete long range order exists in both cases. However, Smith" showed that the hardness of ß brass depended upon the cooling rate and the temperature from which brass is quenched. Smith showed that the hardness was a maximum for specimens quenched from about 445 °C and that the as-quenched structure softened at room temperature at a rate depending upon the temperature prior to quenching. This softening after quenching is in this paper referred to as age softening. The results of this investigation are qualitatively the same as the findings of Smith. However, a more detailed analysis of these phenomena has been possible since the stress-strain curve offers a more sensitive index of the state of the metal than hardness. It is the purpose of this paper to show how the mechanical properties are related to the ordering of ß brass. A 200-lb ingot made from electrolytic copper and electrolytic zinc was extruded to 1/2in. rod. Chemical analyses at frequent intervals along the rod showed that the alloy contained 51.5 pct Cu with the greatest impurity being iron, at 0.01 to 0.001 pct. To obtain a constant test material, the 1/2in. extruded rod was warm-rolled to % in. diameter at 200°C and then recrystallized to a grain size of 2.0 mm. The specimens for the compression test were % in. high and % in. in diameter. The specimen ends were polished on 600 metallographic paper and coated with Molykote for a lubricant. The compression rig consisted of an anvil resting on the machined table of the Baldwin Southwark testing machine and a plunger fixed to the movable cross

Jan 1, 1954

By L. J. Buteau, R. E. Reed-Hill, W. A. Slippy

In a zirconium {1121} twins tend to have coherelzt boundaries and thus do not usually taper to a point when they intersect a grain boundary. Under the proper conditions, a (1121) twin may deform a boundary in such a manner as to clearly rcveal the twinning shear. Measurements of these grain-bounrlary rotatzons yield a value of 0.63 for the (1151) twinning shear. The magnitude of the observed shear and its shear sense are in excellent agreement with the assumption that the second undis-torted plme (K2) for this form of twinning is the basal plane (0002). The present value of the tzvinninz shear, which is approximately three limes larger than Rapperport&apos;s value? is in excellent agreement with reported results of Sokuskii and Prolsenko.5 RECENTLY westlake&apos; reported a study of the twinning modes of zirconium based on ~ap~er~ort&apos;s2 values for the twinning elements. He observed that two of the modes, (1012) and {1122), can be explained by relatively simple dislocation models. A workable model for (1121) twinning, however, proved to be very complex and questionable. Because Rapperport&apos;s second undistorted plane, (K2), for (1121) twinning has large indices, {ll2l6), it is possible that the difficulty in defining a model for (1121) twinning lies in an incorrect value for K2. A measurement of this twinning element has therefore been made, using a method based on observations of the shear displacement of grain boundaries at positions where they are intersected by (1121) twins. EXPERIMENTAL PROCEDURES The zirconium specimens were deformed in tension on an Instron machine either at the temperature of liquid nitrogen (77ºK), or prestrained at liquid nitrogen temperature and then further deformed at room temperature. Straining at 77°K was employed in order to nucleate (1 121) twins in large numbers, since simple ropm-temperature tensile deformation favors (1012) twinning. Specimens were machined from 1/2-in.-thick plate. The material was arc-melted sponge zirconium annealed to an ASTM grain size 4 and containing, in parts per million, 380 Fe, 880 0, <40 Hf, 32 N, and < 5 H. The specimen gage length and diameter were 1.25 and 0.130 in., respectively. To insure a gage section initially free of twins, the last 60 thousandths of the specimen diameter was removed by acid machining.

Jan 1, 1963

By D. I. Bardos, F. X. Spiegel, R. K. Malik, Paul A. Beck

Study of the occurrence of elongated ß-Mn phase fields and of their direction of extension in fifteen ternary systems indicates that the ß-,mn phases formed by manganese with other transition elements and with either silicon, germanium, or tin may be considered as electron phases. In these phases the alloying behavior of silicon on the one hand and of germanium and tin on the other shows a significant difference . Formally all observations can be satisfactorily described by attributing to germanium and tin an apparent electron concentration of nine electrons per atom. This behavior may be interpreted by assuming that germanium and tin exclude itinerant electvons because of a strong repulsive potential arising fromthe requirement that their wave junctions be orthogonal to those of- the closed d shells of these atoms. The absence of a d shell in silicon allows this atom to admit itinerant d electrons. The following new ternary phases of unknown structure were identified by means of their X-vay difjraction patterns: (Mn,Co,Si)I , (Mn,Co ,Si)Y, (Mn.Co,Si)Q , (Mn ,Ni ,Si)W , and (Mn, Ti ,Si)A. The X-ray data suggest that these phases have large unit cells and that to some extent they may he related structurally to the 0 phase. The a phase and certain other phases formed by transition elements are characterized by their preferred occurrence at a constant electron concentration. AS a result, these "electron phases" have relation to electron concentration. The tendency of the B phase to form elongated phase fields in ternary systems along the directions of constant electron concentration has been previously demonstrated. The occurrence of an elongated 0-Mn phase field in the ternary system Mn-Co-Si was schematically indicated by Cherkashin et al.l0 The present study includes fifteen ternary systems, each containing in addition to manganese a second transition element from the group Ti, V, Cr, Fe, Co, Ni and one of the nontransition elements silicon, germanium, or tin. In each system the boundaries of the B-Mn phase were determined in the 900°, 950°, or 1000°C isothermal section, the temperature being dictated on the one hand by the requirement of sufficient rates of diffusion to approach equilibrium conditions in reasonably short annealing periods and on the other hand by the need to avoid as much as possible the partial melting of alloys during annealing.

Jan 1, 1967

By David J. Mack

The structures and properties of the copper-aluminum alloys have been the subject of much study since the classic investigation of Carpenter and Edwards1 focused attention on. the engineering utility of these alloys. It was recognized at an early date that the metallographic structures developed in the aluminum bronzes were similar to those developed in steels, both in the annealed and the rapidly cooled state. Most investigators have been concerned with the acicular, martensitic-like structure formed from the 0 solid solution upon rapid quenching; the transformation of the ß under equilibrium cooling to a lamellar eutectoid having been relatively neglected. With the introduction in 1930 by Davenport and Bain2 of the isothermal transformation technique for studying eutectoidal decompositions, a new field was opened. Although an enormous amount of work has since been done on the isothermal transformation of steel, study of structurally analogous systems has been almost totally overlooked. The outstanding exception was the prize-winning paper† of Smith and Lind1ief³ ho investigated the decomposition of the 0 phase in copper-aluminum alloys by isothermal methods. This was followed in 1934 by Wasserman&apos;s review&apos; of available information on analogous transformations in eutectoid alloys. Since that time no comprehensive study of isothermally transformed eutectoids analogous to steel has appeared, although many valuable contributions have been made to an understanding of the structures developed in such systems. Important papers have been published by Kurdjumow, Gridnew and co-workers, Obinata,18.&apos;9 Greninger,20.21 and Others. The work to be described in this paper was an outgrowth of preliminary studies on the isothermal transformation of a entectoid aluminum bronze, after it became apparent that the alloy under study was reacting somewhat differently than the similar alloy used by Smith and Lindlief. Preliminary Experiments The material used in this study was a high purity aluminum bronze especially prepared by Ampco Metal, Inc. It analyzed: Copper—88.07 pet, Aluminum—11.89 pct, Iron-—0.02 pet, Manganese—-.OI pct, Others—Balance. Although some disagreement exists on the exact composition of the eutectoid, this alloy was believed to be of essentially eutectoid composition even though some pro-eutectoid* delta particles existed in the microstructure of furnace cooled specimens. Specimens transformed isothermally at temperatures slightly below the eutectoid showed relatively large amounts of pre-eutectoid delta, but as will be shown later, this results

Jan 1, 1949

By H. F. Gossenberger, J. J. Tietjen, J. J. Gannon, C. J. Nuese

External quantum efficiency measurements at 300" and 77°K are presented for vapor-grown GaAs and GaAs1-xPx electroluminescent diodes as a function of junction depth and doping. In GaAs, external efficiencies are found to decrease exponentially with increasing junction depth, defining an average absorption coefficient of 900 cm-1 at 300°K and 350 cm-1 at 77°Kfor epitaxial layers of p-type GaAs. It is shown that photon absorption losses dominate at room temperature and, in fact, account for most of the external efficiency degradation between 77° and 300°K. Healever, the internal (&apos;junction) quantum efficiency is also found to decrease by a factor of 3.5 between 77" ALTHOUGH rapid progress has been made in recent years with GaAs, Gap, and their alloys for use in electroluminescent diodes, there are still important unknown factors related to the performance of these de- and 300°K. The dependence of GaAs efficiencies on donor and acceptor concentrations is presented, illustrating best efficiencies at donor concentrations of 1.5 to 2x 1018 cm-3 . External efficiencies are found to be independent of acceptor concentrations less than 3 x 1019 cm-3 but to degrade at higher doping. The fabrication of GaAsi-xPx electroluminescent diodes is briefly discussed. External efficiencies here for planar uncoated diodes are about 0.035 pct at 300°K and 0.4 pct at 77°for x = 0.42. A brightness of about 8500 ft-Lamberts is attained at 77°K and of 315 ft-Lamberts at 300° K. for curvent densities of 10 amp per sq cm. vices. For example, although the external efficiency is known to decrease by factors of typically 10 to 30 between 77°K and room temperature, the exact causes of this are still uncertain. Experimental results of ill&apos; and carr2 with zinc-diffused electroluminescent diodes suggest that this external degradation is almost entirely due to increased absorption losses at room temperature, with a relatively temperature-independent internal efficiency; recent calculations by Gonda et al.3 corroborate this hypothesis. In contrast, Pilkuhn and Rupprecht4 find the internal efficiency of solution-grown GaAs laser diodes to degrade from 100 to 66 to 40 pct as the temperature is increased from

Jan 1, 1969

By M. B. Bever, A. M. Reti, A. K. Jena

The results of this investigation show that in the system SnTe-PbTe l) the solid solutions have small exothermic heats of formation relative to the binary compounds, 2) solid-solution hardening is almost absent, 3) the tin and lead atoms are .randomly distributed on the sublattice occupied by them and do not undergo an ordering transition during a thermal treatment designed to promote such a transition, and 4) the lattice parameter changes linearly with composition. These findings suggest that the solid solutions of tin telluride and lead telluride approach ideal behavior. THE binary compounds SnTe and PbTe form a continuous series of solid solutions.&apos; Information on several physical properties of these solid-solution alloys has been published.1"3 In the work reported here, the heats of formation, microhardness, and lattice parameters of these alloys have been measured and the possibility of an order-disorder transition has been investigated. Order-disorder transitions occur in some solid solutions of binary compounds. In the system Bi2Te3-BizSes, for example, the electropositive bismuth atoms and the electronegative tellurium and selenium atoms always occupy separate layers. In the disordered alloy Bi2Te2Se, the tellurium and selenium atoms are randomly distributed on the layers occupied by them, while in the ordered alloy they occupy distinct layers.4 The NaC1-type (Bl) structure of SnTe-PbTe alloys consists of two sublattices, one of which is occupied by the electropositive tin and lead atoms and the other by the electronegative tellurium atoms; any ordering would be expected to occur in the sublattice occupied by the tin and lead atoms. PREPARATION OF SPECIMENS Polycrystalline specimens of PbTe and Sn1-xPbxTe (x = 0.25, 0.50, and 0.75) were prepared by melting stoichiometric amounts of lead (99.999 pct), tin (99.98 pct), and tellurium (99.999 pct) in evacuated and sealed Vycor tubes. Because of the deviation of tin telluride from the stoichiometric composition5 this compound was prepared by melting 49.8 at. pct Sn and 50.2 pct Te. The tubes containing the melts were quenched into water; the solidified ingots were removed from the tubes and annealed for 2 weeks in vacuum (PbTe approximately 100°C below its melting point, the three alloys 100°C below their solidus tem-

Jan 1, 1969

By C. Ernest Birchenall, Gerd M. Rosenblatt

The pressure and molecular weight of the antimony vapor over solid solutions of tin in antimony, containing 97.4, 94.9, 93.0, and 90.7 at. pct Sb, have been measured from 445° to 545°C by the torsion-effision method. The vapor is all Sb, within experimental error. A solidus curve which differs somewhat from the accepted curve has been calculated using the measured antimony activities. Metallographic examination of additional annealed alloys substantiates the accepted solidus. The solid solutions, which show negative deviations from ideality, probably do not deviate greatly from regular solution behavior. HANSEN&apos; considers the Sb-Sn phase diagram to be well established with the exception of the boundary of the (Sb) phase.* Although there have been no pre- Their data can be combined with data for the solid alloys to calculate the solidus curve of the (Sb) phase. This paper presents measurements of the pressure ant1 molecular weight of antimony over Sb-Sn solid solutions containing 97.4, 94.9, 93.0, and 90.7 at. pct sb. Measurements were made by simultaneous use of the volmer3 torsion and Knudsen, effusion methods. The results of these measurements have been combined with the vapor pressure of pure antimony5 to obtain the activity of antimony in the primary solid solutions. The solidus curve calculated from these data differs somewhat from the accepted curve and is rather uncertain. Metallographic examination of Sb-Sn alloys was carried out to clarify the position of the solidus of the (Sb) phase. EXPERIMENTAL The apparatus and technique have been described previously.5 The measurements were made with the same effusion cells and torsion wire used in the measurements on pure antimony. The torsion measurements were calibrated with mercury at 30" using a mercury vapor pressure of 2.96 x 10-3 mm Hg determined by concurrent, absolute, weight-loss experiments. As in the measurements on pure antimony, an extraneous vapor was observed to distill off during the first run after the cell had been loaded with A fresh sample of alloy and during the first minute or two of every run. The change in composition after a series of runs with one sample was of the order of 0.1 at. pct and thus completely negligible in the calculation of the thermodynamic properties. The alloys were prepared from pieces of Merck antimony and Matheson, Coleman, and Bell reagent-

Jan 1, 1962

By O. D. Sherby, J. E. Dorn, C. D. Wiseman

MCLEAN&apos; has shown that the total strain obtained during creep of aluminum polycrystals arises exclusively from the mechanisms of 1) microscopically observable slip, 2) subgrain tilting, and 3) grain boundary shearing. Extensive analyses, however, suggest that the high temperature creep of metal polycrystals is controlled by a single thermal activation process."" These somewhat contradictory observations might be reconciled if it could be shown that the activation energies are identical for each of the mechanisms isolated by McLean. Such identity of the activation energies, of course, would demand that the same unit process controls the functioning of each individual mechanism. Under these conditions the activation energies for creep of single metal crystals and polycrystalline aggregates and for grain boundary shearing should be identical. This paper is primarily concerned with the possible identity between the activation energies for high temperature creep of single crystal and polycrystalline metals. In addition, comparisons will also be made between the activation energies for creep of single crystals and polycrystals with previously reported activation energies for grain boundary shearing.0"8 Materials and Techniques The same high purity aluminum, lead, and tin were used in the creep tests for single crystals and polycrystalline aggregates. Single crystals of aluminum and tin were prepared by the strain-anneal technique, whereas lead single crystals were prepared by growth from the melt. The tensile creep stress was maintained constant by Chalmers-Andrade parabolic-type lever arms. Strains were measured to &0.0002 in. per in. with rack and pinion type extensometers, and temperatures were maintained to within & 0.2"C of the reported values by mercury-thermoregulated resistance-heated silicone oil baths. The previously reported unambiguous technique for determination of the activation energy for creep was employed throughout this investigation.&apos; ." It involves periodic abrupt small changes in temperature during the course of creep, accomplished by rapidly replacing one creep bath at temperature TI by a second bath at T,. The abrupt change in creep rate from i, to & attending the abrupt change in temperature is due exclusively to the change in temperature, since both the stress and the substructure are identical the instant before and the instant after a change of temperature. Therefore, all other factors being identical where AH is the activation energy for creep and R is the gas constant. Results Typical examples of the creep rate vs creep strain data during temperature cycled creep tests of single

Jan 1, 1958

By W. F. Stowasser

Robert E. Hagen (Oliver Iron Mining Div., U. S. Steel Corp.)—Mr. Stowasser and his associates are to be congratulated on their achievements in developing the design of a pilot agglomerating plant, based on information obtained from experiments made in a laboratory sinter pot, and subsequently constructing and successfully operating this plant. In his Transactions article, May 1955 (vol. 201) Mr. Stowasser stated that the output of his heat treating strand was about 2 Lt per sq ft of grate area per day and that the fuel consumption was 0.7 to 0.8 million Btu per Lt of product. If it is assumed that the burning zone extends from the back of the ignition furnace to the beginning of the recuperation windbox, only about 1/3 of the grate area over the windboxes is utilized for burning pellets, and the actual rate at which partially dried pellets are burned is about 6 Lt per sq ft of grate area per day. It may be interesting to compare the above operating data with that obtained at the Extaca plant, where taconite concentrate is treated on a conventional sin- tering machine using limestone or hydrated lime additives with no recuperation of heat. The entire windbox area is used for burning, and a production rate of 2.5 Lt per sq ft of windbox area per day has been attained at a fuel consumption of 1.8 to 2.0 million Btu per Lt of product, the latter being considerably in excess of that reported by Mr. Stowasser, partly because a circulating load of returns amounting to 28 to 30 pct of the machine feed is used and because no attempt is made to recuperate heat from the waste gases. With the high capital and labor costs prevailing today, it seems that future development of the downdraft grate pelletizing process should be directed toward taking advantage of the high burning rate of predried pellets and increasing capacity, perhaps at the expense of fuel economy, by decreasing the proportion of grate area utilized by ancillary functions. For example, eliminating the cooling zone and using this area for burning would increase the proportion of grate area available for burning from 33 to 50 pct of the total windbox area, and a proportionate increase in capacity would result.

Jan 1, 1956

By R. R. Hart, B. C. Wonsiewicz, G. Y. Chin

In recent years there has been increased miniaturization of electromechanical devices to keep pace with current trends toward smaller electronic components. A major problem facing the designer, however, is the higher stresses encountered by the material as a result of shorter springs. Hence an improvement in the elastic limit, as approximated by the 0.01 pct offset yield strength, would be highly desirable. An increase of 25 pct in the yield strength, for example, will permit a 20 pct reduction in both the length and thickness of a cantilever-type spring while maintaining the same compliance. One technique of improving the yield strength that has received little commercial attention is crystal-lographic texture strengthening.1,2 Texture strengthening is expected to be most beneficial in materials of hcp structure, but considerable gain can also be expected in cubic materials. A wire with a (111) fiber texture, for example, is expected to be 20 pct stronger than randomly oriented material, and 50 pct stronger than wire with a (100) fiber texture.293 For sheet specimens with a {110}(112) texture, characteristic of many heavily rolled fcc alloys, the (111) transverse direction is expected to be the maximum yield strength direction, about 20 pct higher than that in the (112) rolling direction.&apos; In addition, the (111) direction is the direction of maximum modulus of elasticity for most cubic alloys. A large value of the elastic modulus could be desirable in designs where stiffer springs are required. To test the above idea, a 0.090 in. (-2.3 mm) thick commercial grade A (5 pct Sn) phosphor bronze sheet, a widely-used material for relay springs, was rolled from the spring-tempered condition (60.5 pct reduction) to various additional reductions up to a total reduction of 95 pct. Subsequently, additional material was obtained with a total thickness reduction of 97.3 pct Standard tensile specimens were prepared from the sheet material with the tensile axis parallel to and at 90 deg to the rolling direction. Tests were run on an Instron testing machine at a strain rate of about 0.050 min-l. Textures were determined by the use of the reflection pole-figure technique. Data were obtained using nickel-filtered CuKa radiation and with the aid of a Siemens pole figure goniometer. The X-ray pole figure studies show an incrzasing development of the texture toward the {110}(112) ideal

Jan 1, 1970

PRESIDENT ARTHUR DWIGHT District 0 NEW YORK, N Y PAST PRESIDENTS EDWIN LUDLOW District 0 MINNEAPOLIS, MINN HERBERT HOOVER, District 4 WASHINGTON, D C FIRST VICE-PRESIDENT JVC REYNOLDS NEW YORK, N Y

Jan 1, 1923

By J. C. McDonald

A DDITIONAL experimental data are presented in this note on a phenomenon which has been touched on but lightly in the literature. The common magnesium base rolling alloy (AZ31B) contains about 3 pet A1 and 1 pet Zn. When cold rolled, it hardens until it starts to break up in the rolls at 30 to 50 pet reduction. When it is heated after rolling to full hardness, it softens. However, other magnesium alloys have shown themselves capable of being cold rolled indefinitely, provided the ratio of roll diameter to starting gage is sufficiently high. As measured by the tensile test, these alloys actually soften when the reduction becomes large (60 to 90 pct). A subsequent heating at 300&apos; to 500°F can produce hardening of this metal. Heating at higher temperatures (600&apos; to 800°F) causes recrystalliza-tion and softening. Menzen&apos; has shown that a magnesium base alloy can be cold rolled without intermediate anneals as much as 90 pet. The alloy studied, Mg-1.5 pet Mn, softened considerably between 20 and 90 pet reduction, as measured by tensile properties; a decrease in yield strength of 30 pet, and an increase in elongation from 3.2 to 16.7 pet (longitudinal direction of the sheet). However, Menzen gives no data on the reaction of this metal. to heating. Ansel and Betterton2 and Hurst and Hatch3 report a similar effect in Mg-1.5 pet Mn-0.1 pet Ca. Their data show an initial hardening, followed by softening. The former authors also show that the alloy softened by cold rolling will harden when heated at low temperatures, and that these effects are absent in Mg-3 pet Al-1 pet Zn. In the course of work4, 5 some years ago, the author observed similar effects with alloys containing cerium, thorium, or zirconium; but not with elements like aluminum, silver, or zinc. Table IA contains the results of an experiment which shows these effects rather well. A binary alloy with 0.3 pet total rare earths (Mischmetal* added) was rolled hot to 1/16 in. and then annealed to full softness by heating 30 min at 800°F. Rolling was continued at 1.5 pet per pass to 80 pet total reduction on 8 in. diam rolls. The metal was harder after 20 pet work than initially but, at 80 pet reduction, properties were back to their original values. Heating for 1 hr at 450°F produced about the same hardness whether the reduction was 20 or 80 pet. At intermediate reductions, the metal hardened, but not to as high values. Extensive cold rolling may also be carried out on metal hot rolled at temperatures sufficiently low to produce a semihard temper. Mg-0.6 pet Zr was rolled to 0.1 in. at 700° to 800°F, 30 pet per pass. As shown in Table IB, a further cold reduction of 85 pet, at 1.5 pet per pass, definitely softened the metal.

Jan 1, 1959

By Axel Hultgren

In ingots of silicon-killed carbon steel-made without addition of aluminum, transparent spherical or nearly spherical inclusions, up to about 0.15-mm diameter, are generally present. They may be glassy or crystallized, wholly or partially In steels of high carbon contents they consist of silica,4,12 in steels of lower carbon contents and, in consequence, higher oxygen contents, of iron-manganese-silicate with higher iron and manganese contents the lower the carbon content. Small silicate inclusions, about 0.01 mm or smaller, may occur, just as sulphide inclusions do, in portions that have been the last or nearly the last to freeze,l0,12,17 this location being verified by primary etching.10 Hence, it may be concluded that they have separated from liquid steel that has become enriched in oxygen through segregation during freezing. Silicate inclusions with a diameter larger than about 0.02 mm appear, at least in ingots of moderate size, to be distributed at random in relation to the primary structure and therefore may be assumed to have existed as droplets in the liquid steel before freezing started at the point in question. The average size of such large inclusions has been found to increase toward the axis1&apos; and their amount to increase from the top downward in the axial region.2,10 It has been assumed that this accumulation is a result of the droplets being brought down by the slowly settling metal crystals.2 It has been suggested that large silicate inclusions generally form,6 or may form,&apos;&apos; by coagulation of smaller ones, or by small drops being caught by larger ones during the rising of the latter.9 The occasional occurrence of a large inclusion surrounded by a swarm of small ones has been taken as a proof of this mechanism but, as suggested later, may be explained in another way. It has been pointed out that an inclusion droplet in the liquid steel may grow at the expense of an adjacent one, which implies diffusion of soluble inclusion-forming elements in the liquid steel.&apos;= Further, it has been pointed out that, on cooling in ladle or mold, the metal-silicate equilibrium is displaced in the direction of separation of silicate. Thus inclusions may grow in size and amount.2,3,8,12,13,17,19,20 The exposure of the liquid steel to the oxygen of the air during tapping and pouring, and the consequent reaction, has been mentioned as a source of the formation of inclusions19.20 but this possibility has not received particular attention. Further, the admixture of furnace slag during tapping1 or of refractory material from various sourcesl,20 has been considered. The inclusions due to the latter may be recognized, however, through their resistamce to hydrofluoric acid, imparted by the alumina content. Silicate inclusions are often referred to as the natural and inevitable product of reaction on adding silicon or silicon

Jan 1, 1949

By Axel Hultgren

In ingots of silicon-killed carbon steel-made without addition of aluminum, transparent spherical or nearly spherical inclusions, up to about 0.15-mm diameter, are generally present. They may be glassy or crystallized, wholly or partially In steels of high carbon contents they consist of silica,4,12 in steels of lower carbon contents and, in consequence, higher oxygen contents, of iron-manganese-silicate with higher iron and manganese contents the lower the carbon content. Small silicate inclusions, about 0.01 mm or smaller, may occur, just as sulphide inclusions do, in portions that have been the last or nearly the last to freeze,l0,12,17 this location being verified by primary etching.10 Hence, it may be concluded that they have separated from liquid steel that has become enriched in oxygen through segregation during freezing. Silicate inclusions with a diameter larger than about 0.02 mm appear, at least in ingots of moderate size, to be distributed at random in relation to the primary structure and therefore may be assumed to have existed as droplets in the liquid steel before freezing started at the point in question. The average size of such large inclusions has been found to increase toward the axis1&apos; and their amount to increase from the top downward in the axial region.2,10 It has been assumed that this accumulation is a result of the droplets being brought down by the slowly settling metal crystals.2 It has been suggested that large silicate inclusions generally form,6 or may form,&apos;&apos; by coagulation of smaller ones, or by small drops being caught by larger ones during the rising of the latter.9 The occasional occurrence of a large inclusion surrounded by a swarm of small ones has been taken as a proof of this mechanism but, as suggested later, may be explained in another way. It has been pointed out that an inclusion droplet in the liquid steel may grow at the expense of an adjacent one, which implies diffusion of soluble inclusion-forming elements in the liquid steel.&apos;= Further, it has been pointed out that, on cooling in ladle or mold, the metal-silicate equilibrium is displaced in the direction of separation of silicate. Thus inclusions may grow in size and amount.2,3,8,12,13,17,19,20 The exposure of the liquid steel to the oxygen of the air during tapping and pouring, and the consequent reaction, has been mentioned as a source of the formation of inclusions19.20 but this possibility has not received particular attention. Further, the admixture of furnace slag during tapping1 or of refractory material from various sourcesl,20 has been considered. The inclusions due to the latter may be recognized, however, through their resistamce to hydrofluoric acid, imparted by the alumina content. Silicate inclusions are often referred to as the natural and inevitable product of reaction on adding silicon or silicon

Jan 1, 1949

By I. Hawke, K. Barron

I. Hawkes (Postgraduate School in Mining, University of Sheffield, Sheffield, England) — The photoelastic stressmeter is proving to be a very practical tool for &apos;in-situ&apos; measurements in the fields of civil and mining engineering and Barron&apos;s article has therefore come at a very opportune time, supplementing as it does, the considerable amount of laboratory and field data which is being accumulated.1,2,3 There are however several points relating the application of Barron&apos;s conclusions to the practical use of the meter which require further elucidation. EASE OF READING If the photoelastic stressmeter is to have a wide application, the fringe orders must be easily measured. The system adopted by the writer and his colleagues at Sheffield for the uniaxial stress case is to read the fringe order at the 45 point, 0.20 in. from the center (11/4 in. diam meter). This procedure has been recommended because the fringes not at this point form a very distinct &apos;eye&apos; which is obvious even to those who have had little experience with photoelastic fringe patterns. Barron points out that this point can also be used up to a stress ratio of 0.33 and in practice this is normally done. In biaxial fields above a ratio of 0.33 the &apos;eye&apos; is no longer apparent and the fringe order must be ascertained at some other point. The writer and his colleagues experimented at various points and finally chose a point at a distance 0.175 in. (11/4 in. diam meter) on the minor stress axis and fixed this point on the meter by inserting a collar of this diameter. This procedure enables the &apos;eye&apos; technique to be used for uniaxial stresses as the &apos;eye&apos; falls outside the collar; any other technique for biaxial patterns would require lines to be engraved on the meter itself and reading difficulties would be experienced by all but the most highly trained. It is interesting to point out that in a great many field applications ranging from underground pillars to building foundation piles the stresses measured have been uniaxial. In such cases, reading the fringe order has been simple even for unskilled persons. SENSITIVITY The photoelastic stressmeter acts as an inclusion, and as such its theoretical behavior is as described by Barron&apos;s mathematical analysis. When considering its practical application, however, it must be remembered that rocks and concrete are not mathematically ideal substances. The theory relates the fringe order in the meter to the stresses and the E (Young&apos;s Modulus) and the µ (Poisson&apos;s Ratio) values of the surrounding material. There is of course no unique E or µ value for rocks or concrete. These values change both with stress level and time load application sometimes to the order of 300%. We at Sheffield have very accurately calibrated the photoelastic stressmeter in a wide range of materials and have also measured the average E values for these materials. The results prove that the meter sensitivity

Jan 1, 1965

By M. E. Nicholson

IT has been suggested by a number of investigators, I including Hume-Rothery and Raynor,&apos; that certain intermediate phases in metal systems take on interstitial crystal structures because of an appropriate ratio of radii of the two atoms. If the size factor is an important parameter in determining whether or not an intermediate phase will have an interstitial structure, then it would appear reasonable that the relative sizes of interstitial atoms should have a direct relation to their solubilities in interstitial compounds. It was on such a basis that Petch,&apos; in his discussion of the cementite structure, concluded that nitrogen is the only possible element which could replace carbon. Recent X-ray studies by Jacka indicate that the solid solubility of nitrogen in cementite is negligible. If this is the case, then on the basis of size factor it would not be expected that any element can replace carbon in FeaC, since according to Schwarzkopf and Kieffer4 the covalent atomic radii of nitrogen, carbon, and boron are 0.71, 0.76, and 0.87A, respectively. Nevertheless, Vogel and Tammann in 1922 indicated that a quasi-binary relation exists between the interstitial compounds FeaC and Fe2B and that the solid solubility of boron in FeaC at approximately 1150°C is 1.4 pct B by weight. Because of the apparent disagreement between theory and experiment, the solid solubility of boron in FeaC has been reinvestigated. In addition, the influence of boron on the saturation magnetic moment (per gram) and Curie temperature of cementite was determined. Experimental Procedure A series of Fe-B-C alloys which varied in boron content from 0 to 5.4 wt pct B were prepared by arc melting a 50-g ingot using carbonyl iron, Ache-son AUC graphite, and Cooper grade A boron for starting materials. The composition of these alloys is listed in Table I and shown graphically in Fig. 1. The samples represented by the solid circles were used for X-ray analysis and Curie temperature measurements; by the squares, samples used for quantitative metallography; and by the triangles, samples used for saturation magnetic moment measurements and Curie temperature measurements. After arc melting and subsequent quenching from 1000°C, so that all phases in the resulting microstructure were brittle, one half of the 50-g ingots were pulverized until a powder was obtained which was less than 100 mesh. These powders were then homogenized in evacuated Vycor capsules at 1000°C for 24 hr and water quenched. Although the homogenized powder had sintered somewhat, it was suitable for saturation magnetic moment and Curie temperature determinations, for which the 60 to 100-mesh fraction of the powder was used. For X-ray analysis the homogenized powder was crushed again until a 300-mesh powder was obtained. After crushing, the powder was mixed with Alundum of approximately the same grit size to prevent sinter-

Jan 1, 1958