Search Documents

By Ted C. Briggs

Nitrogen exists in two broad categories commonly designated as elemental nitrogen and fixed nitrogen. Elemental nitrogen is found in nature as a diatomic molecule and constitutes about 78%, by volume, of the earth's atmosphere. Fixed nitrogen is a common term used for nitrogen that is chemically bound to other elements. Although elemental nitrogen is very abundant, nonleguminous plants cannot utilize nitrogen unless it is in the chemically combined form. The content of this chapter is confined to fixed nitrogen since the uses and properties of elemental nitrogen and the fixed nitrogen compounds are different. Bacteria associated with legumes are able to fix atmospheric nitrogen, but not to the extent or in the locations required by modem agriculture. The need to use fertilizers containing fixed nitrogen compounds to grow food crops has been recognized for hundreds of years, and from antiquity farmers have used organic wastes such as animal manures, vegetable wastes, sewage sludge, fish scraps, etc., containing these compounds for fertilizers. The organic materials have a low nitrogen content, however, and cannot support large-scale food production. Known commercial-size deposits of natural nitrates containing much higher nitrogen content exist only in Chile, and the possibility of the discovery of other significant deposits is remote. The Chilean deposits were the major source of nitrogenous fertilizers until about 1913, when the Haber-Bosch process for the production of synthetic ammonia was developed. In the Haber-Bosch process, nitrogen reacts with hydrogen, at high temperatures and pressures and in the presence of a catalyst, to form ammonia. At present Chile is the only country in the world with a nitrate mining industry, and, although the mining of natural nitrates is an important industry in Chile, natural nitrates are relatively unimportant, worldwide, because of the adoption of fixed nitrogen processes. The relative amount of the world demand for fixed nitrogen that is derived from natural nitrates has declined in recent years and will continue to decline. Modern farmers are sophisticated in economic calculations such as cost to benefit ratios and, for the most part, they purchase plant nutrients which give the highest return on their investment. Natural nitrates cannot compete on a fixed-nitrogen cost basis with anhydrous ammonia and its derivative products. In a limited sense, the fixed nitrogen industry is mining the air. Modern plants use air, water, and, in most cases, natural gas to produce the ammonia that is now the key building block of the fixed nitrogen industry. To present an accurate picture of the industry, this chapter on nitrogen follows a format somewhat different from that of other chapters in this volume.

Jan 1, 1975

By J. L. Jorstad

The hypereutectic Al-Si alloys 390 and A390 have wear characteristics superior to any of the more common aluminum casting alloys. This excellent wear resistance, coupled with good mechanical properties, high hardness, and low coefficient of thermal expansion, has made these alloys candidates for the all-aluminum internal combustion engine, the application for which they were primarily developed. A390 alloy is intended for sand and permanent mold casting, and requires a lower iron ccxltent (0.5 pct maximum) than its die casting companion 390 alloy (0.6 to 1.1 pct Fe). The 17 pct nominal silicon in these alloys provides sufficient quantities of the hard primary silicon phase to assure a high degree of wear resistance, yet little enough of this phase, to minimize the casting and m achining problems associated in the past with the hypereutectic alloys. The mechanical and physical properties of 390 and A390 alloys are competitive with the best of the common aluminum casting alloys with the exception of low ductility. This low ductility is not considered a detriment, since in many applications these alloys replace cast iron. Corrosion resistance is similar to the standard alloys 380 and 333. Numerous parts, of varying degrees of complexity, have been cast of alloys 390 and A390, including engine blocks and heads. The deviations from normal good handling and casting practices that are required for the alloys are those associated with the presence of the primary silicon. To obtain optimum strength and machinability, the molten alloys should be treated with phosphorus to refine the primary silicon phase. Care must be exercised to properly control the pouring temperature and rate in order to minimize primary silicon growth and segregation. AUTOMOTIVE engineers have for years recognized the advantages of lighter weight and better heat transfer that aluminum could offer as material of construction for engine blocks. These advantages alone, however, are insufficient justification for acceptance of aluminum engines by the automotive industry. To be acceptable, an aluminum engine first must pass all tests to which cast-iron engines are subjected, and, in addition, must represent no cost penalty in manufacturing. None of the conventional aluminum casting alloys have sufficient wear resistance to withstand the tests to which cast iron is subjected as a cylinder bore material, and recent attempts to manufacture aluminum engines with cast-in-place iron sleeves could not compete costwise with the equivalent cast-iron engine. The prerequisite to an acceptable aluminum engine seemed to be a casting alloy with a high degree of wear resistance that would eliminate the necessity of cast-in iron sleeves or liners. The hypereutectic A1-Si alloys 390 and A390 have met this challenge.' Combined with modified pistons and a patented cylinder bore surface finish,2 the performance of these alloys in more than 1300 cold start and cold scuff tests, over 3500 hr of dynamometer wear and endurance tests, and more than 350,000 miles of road tests leaves no doubt as to the feasibility of running on bare aluminum cylinder bores. ALLOY DEVELOPMENT The desirable characteristics of the hypereutectic A1-Si alloys have been recognized for some time. Their excellent wear resistance and low coefficient of thermal expansions have been used to advantage in the production of diesel-type pistons in Europe and to a limited extent in this country. The major contributor to the good wear resistance of these alloys is the extremely hard primary silicon phase in the microstructure. Although the percent silicon used experimentally has been much higher, most commercial alloys have ranged from about 14 to 25 pct. Generally, as the silicon content is increased, wear resistance increases, and the coefficient of thermal expansion decreases. With increases in silicon, however, machinability and cast-ability tend to suffer. The development of a satisfactory aluminum engine block material at Reynolds involved the testing and evaluation of many alloys, covering a wide range of silicon contents and numerous variations of iron, copper, magnesium, manganese, and other alloying additions. Castability, mechanical and physical prop-

Jan 1, 1969

By W. F. Hosford, E. W. Kelley

Deformation studies have been conducted at room temperature on single crystals of magnesium and magnesium alloys with thorium and with lithium. Single crystals oriented to suppress shear on the easily activated basal slip systems were deformed by plane-strain compression. Compression along the C axis was accommodated by {1011} banding. Compression perpendicular to the unconstrained c axis activated {1012} twinning, and, after virtually complete twinning, deformation continued by {1011) banding in the twinned material. Compression perpendicular to the constrained c axis was accommodated by the simultaneous operation of (1012) twinning against the constraint and (1011 ) banding. Although this orientation was favorable for {1010)(1210) prism and {1011}(1~10) pyramidal slip, these modes were not observed in pure magnesium or in Mg-0.5 pct Th. However, {10i0)(1~10) prism slip was observed in crystals of Mg-4 pct Li during compression perpendicular to the constrained c axis. Fracture in all materials occurred parallel to (1124) or {l~il) depending on the orientation and composition of the specimen. THE mechanical behavior of the hcp metals is strongly anisotropic. Although several slip systems have been reported the slip is cpmmonly in the directions of closest packing, the (1210),' and this does not produce strains parallel to the c axis. Hence the inherent anisotropy. The deformation mode most easily activated in magnesium at room temperature is (0001)(1210)- basal slip. Also {1010}(1~10) prism slip and {1011)(1210) pyramidal slip have been reported, primarily at elevated temperatures.2"4 However, at room temperature the shear stresses to activate the prism and pyramidal modes are roughly a hundredfold greater than that required for basal slip.'j4 Thus prism and pyramidal slip may be expected only under special conditions of loading. Strains normal to the basal plane can be produced by twinning, however. Many twinning modes have been reported for magnesium,' with (1012) twinning the most common and relatively easy to activate. Magnesium can deform by (1012) twinning when stressed along the c axis jn tension, but not in compression. In contrast, (1011) twinning is activated by compression along the c axis and not by tension. In addition to primary twinning, secondary twinning or slip can occur within the reoriented material of primary twins.' In general at least five independent shear systems must be active to bring about an arbitrary shape change such as that in the individual grains of a deforming polycrystalline material.' Because basal slip can_ provide only two independent shear systems and (1012) twinning can only accommodate an extension of the c axis, other deformation modes must be active in magnesium for an arbitrary shape change to occur. The purpose of this investigation has therefore been to study the various deformation modes in magnesium at room temperature, with special emphasis on those modes that are less easily activated. The effect of the alloying elements, thorium and lithium, has also been investigated. In polycrystalline aggregates, unambiguous identification of deformation modes is extremely difficult and the direct evaluation of the resolved shear stresses to activate them is not feasible. On the other hand, uni-axial tension and compression experiments on single crystals may not activate some of the- deformation modes because basal slip and/or {1012) twinning cannot be suppressed in most orientations. However, it should be possible to activate all possible deformation modes using oriented single crystals and plane-strain compression. Identification of active deformation systems and evaluation of the resolved shear stresses required to activate them should be facilitated. Wonsiewicz and Backofen have recently completed an investigation of the plasticity of pure magnesium crystals at various temperatures utilizing plane-strain compression and selected crystal orientations. This technique has also been used in the present work. The seven orientations selected for study are indicated in Table I. Plane-strain compression along the c axis (orientations A and B) should activate some deformation mode _other than basal, prism, or pyramidal slip, or (1012) twinning. In orientations C and D, prism or pyramidal slip would be expected to take place. When the compressive load is applied perpendicular to an unconstrained c axis (orientations E and F) the three slip modes should be suppressed but not (10i2) twinning. In orientation G, basal slip should occur.

Jan 1, 1969

By Larry Kaufman

A useful method for estimating the entropy of NaCl type compounds has been developed by combining the Debye theory of specific heat with the Lindemann formula. This method pemnits calculation of the entropy from a knowledge of the atomic weight, atomic volume, and melting point of the compound. Comparison of the calculated and observed entropies of 35 NaCl type compounds over a wide temperature range yields good agreement thus establishing the usefulness of the method. Application of the method to other crystal types is also discussed. KUBASCHEWSKI~ has suggested a useful method of estimating the enthalpy of formation of inter-metallic compounds from a knowledge of the crystal structure, lattice parameter, and heats of sublimation of the component elements. This method is quite valuable in predicting the tendency for compound formation in a given system and is of particular value in considering systems for which no experimental data are available. In order to supplement the enthalpy calculation afforded by Kubschewski's method, it would be of value to be able to estimate the entropy of compounds so that the entropy and free energy of formation could be evaluated. Although a considerable body of such data determined by calorimetric and equilibration techniques exists at present, the difficulty of making such measurements (particularly at high temperatures) and the ever increasing number of new compounds which are of interest make the desirability of such a computational method clear. This paper deals with a method for calculating the entropy of a compound from a knowledge of the atomic weight, atomic volume, and melting point. Since these data are generally easier to determine and therefore more readily available than thermo-dynamic data, they should provide an additional tool in estimating the stability and reactivity of compounds at high temperatures. I) THE ENTROPY OF PURE METALS As a first approximation, the specific heat of a pure metal can be represented by a sum of terms where C,($/tI is the vibrational specific heat calculated on the basis of the Debye theory, lo4 TC, (0/T) is an approximation to the Cp - C, correction. T is the electronic specific heat, and Cp (p) is the magnetic specific heat. Although the Debye theory does not provide a complete description of the vibrational specific heat, i.e., the Debye temperature 0 is not a constant, it does provide a good approximation when used properly. Blackman6'7 has written several reviews on this subject discussing the different values of 0 determined by various methods (specific heat, X-rays, elastic constants, electrical resistivity, and so forth), as well as the observed temperature dependence of 0 with T. In the present case the 0 in Eq. [I] naturally refers to the specific heat 0. The variation of Debye 0 (as determined from specific heat measurements) with temperature is observed to exhibit its most radical behavior at very low temperatures. At higher temperatures the 8 values are observed to become more nearly constant. Blackman6'7 has presented the variation of 0 with temperature for several metals. His tabulation is reproduced in Table I. Reference to Table I shows that above a certain temperature level, 0 remains fairly constant. The value of 0 which is most useful in computing the specific heat, and hence the entropy, is the value of 0 in the range 0/6 « T « 0. In 1910, Lindemann' suggested a relation for estimating Debye 0 values. According to this formula, where V is the atomic volume, T is the melting point in 'K, M is the atomic weight, and CL is a constant. Mott and Jones9 present this formula and state that there is at present no satisfactory theoretical explanation, but that it does have an empirical basis. By using the valuesof 0 in Table I along with known1' values of M, T, and the molar volume VM, where the Lindemann constant can be evaluated. This

Jan 1, 1962

By William Y. Holland, Roger M. Cook

In view of the increasingly widespread deterioration of concrete structures as the result of the interaction of the alkalies sodium and potassium released by hydration of portland cement and susceptible rocks and minerals in aggregates, it is believed that a paper summarizing the geographic distribution of these aggregates will be of interest to producers and users of concrete, concrete products, and concrete-making materials. THIS paper reviews the problem of alkali-aggre-gate reaction in concrete and describes the geologic and geographic occurrence and distribution of alkali-reactive sand and gravel in western United States. It includes no discussion of crushed stone or synthetic aggregates. Most deposits of sand and gravel are accumulations of particles of rocks and minerals from a variety of sources, and it is not unusual for at least one or two varieties of the rocks to contain some form of reactive material. Examination by petro-graphic methods of many sands and gravels, as well as manufactured aggregates, has shown that a comparatively high proportion of the deposits does contain, in greater or lesser degree, rocks and minerals known to be deleteriously reactive with the alkalies of cement. Fortunately the amount of reactive materials is commonly less than that necessary to cause deleterious effects in concrete. As investigation of unsound concrete structures progresses, it becomes evident that the alkali-aggre-gate reaction is even more widespread than supposed, Figs. 1 and 2. Even though some parts of the country appear at present to be immune, further investigations will probably show that the effects of alkali-aggregate reaction can be seen in many structures in these areas, although only on a small scale in most of them. Many concrete structures will, of course, have lived their useful life before disintegration from this cause is serious, and in others the alkali-aggregate reaction may never become significant even though the microscopic evidence of reaction is present. The alkali-aggregate reaction first was reported to be a cause of deterioration of concrete in 1940 when Stanton1 described expansion of concrete pavements in California. Similar expansion and deterioration of concrete was recognized during succeeding years in concrete structures located in many parts of the country, but particularly in the western states. A number of concrete laboratories2 became interested in the problem. It was soon determined that only certain combinations of aggregate and cement caused the alkali-aggregate reaction to take place, and moreover that the reaction progresses only in the presence of water. Further research proved that cements containing more than 0.60 pct total alkalies (pct Na,O + 0.658 x pct K2O), when used with aggregates containing appreciable amounts of reactive ingredients, caused the reaction to take place, usually with subsequent deterioration of the concrete. During the last few years this limitation has been adhered to in both government and private construction as the maximum allowable alkali content of cement to be used with aggregates of known alkali reactivity. Because of this limitation, it appears that deleterious reaction either has been reduced or eliminated in many recently built structures in which it probably would otherwise have occurred. Recent tests have shown that the degree of expansion obtained with any particular cement-aggre-gate combination depends not only on the alkali content of the cement but also upon the relation of this alkali content to the amount and degree of reactivity of reactive constituents in the aggregate.' In laboratory mortar bars, opal and cements with alkali content of as low as 0.2 pct (as equivalent of Na2O) have produced deleterious expansion as the result of alkali-aggregate reaction. These experiments demonstrate that aggregates containing even 0.1 pct of opal are deleteriously reactive. It was soon determined that alkali-silica gels were formed by the interaction of the alkalies of the cement and the reactive aggregate, Figs. 3 and 4. Osmotic or swelling pressures produced by the continued hydration of these gels cause expansion of the concrete with resulting cracking, warping, and dislocation. Evidence of the alkali-aggregate reaction can be seen by a petrographic study of the deteriorated concrete. Among the first structures studied by this method was Parker Dam on the Colorado River, California-Arizona. In the concrete from this dam pebbles of rhyolite, andesite, siliceous limestone, and chalcedonic chert were found to be reactive.

Jan 1, 1954

By D. P. Kedzie, R. A. Dodd

The fatigue strength, fatigue hardening, and effect of fatigue deformation on subsequent age hardening of supersaturated Al(Cu) solid solutions have been determined as functions of alloy composition and temperature. The fatigue strength/tensile strength ratios, determined at 150°, 25°, and -195°C, decreased with increase in alloy content for all temperatures, but the F.S./U.T.S. ratios at -195°C decreased much more rapidly than did the ratios for 150" and 25°C. This suggested that strain aging and/or age hardening occurred during tests at higher temperatures. Additionally, the F.S./U.T.S. ratios at 150°C exceeded those at 25°C for all compositions, indicating greater strengthening during fatigue at 150°C. The effect of fatigue or tensile deformation at 150°, 25°, and -195°C on subsequent age hardening showed that the deformatzon increased the rate of precipitation and indicated that mechanically produced vacancies were probably formed during deformation. Fatigue hardening was studied at 150°, 25°, and -195°C, and the effect of room-temperature rests after 10 and 100 cycles was examined. The results confirmed that strain aging occurred at the higher temperatures . DURING the last 15 years various mechanisms of fatigue crack nucleation and growth based on dislocation and vacancy interactions, operating singly or collectively, have been proposed. The probable consensus of present opinion is that the fatigue process in pure metals essentially involves dislocation interactions, and that vacancies formed by such interactions play a minor or inconsequential role. However, there is some evidence that age-hardened alloys tend to overage during fatigue, probably by local vacancy-enhanced diffusion, and strain aging also might be important in selected cases. Furthermore, it has been established that the behavior of quenched-in vacancies in Al(Cu) and other solid solutions is composition-sensitive. Therefore, it seemed worthwhile to investigate various aspects of the fatigue behavior of supersaturated Al(Cu) alloys and to examine the results in terms of vacancy-enhanced effects. EXPERIMENTAL The alloys used in this investigation were prepared from 99.994 wt pet A1 and OFHC copper, the latter containing 0.04 pet 0 as the principal impurity. Six alloys were made, containing, by actual analysis, 0.58, 0.96, 1.96, 2.85, 4.45, and 5.51 wt pet Cu. They were induction-melted in air in graphite crucibles, cast as 7-in. by 7/8-in.-diam rods in graphite molds, and hot-rolled to 5/8 in. diam. The experimental work was a three-part program involving the determination of a) 10' cycle fatigue stresses as a function of alloy composition and temperature; b) the effect of fatigue deformation on subsequent aging of the supersaturated alloys; and c) fatigue hardening as a function of alloy composition and temperature. For determining the 105 cycle fatigue stresses, a portion of the 5/8-in. stock was machined into Krouse rotating cantilever beam fatigue specimens, 2 in. in length by 1/4 in. minimum diameter. These were tested at +150°, 25°, and -195°C (liquid nitrogen) on a Krouse high-speed machine, with special weights to provide lower -than-normal loading ranges, this being necessitated by the small load requirements of those alloys of lower copper content. For the high-temperature tests a small resistance heater was designed to clear the collets and fit in between the chucks, while for the low-temperature tests a hollow nylon cylinder was used, having closed ends drilled to pass a fatigue specimen, and positioned similarly to the heater. A plexiglass container completely enclosed the fatigue machine; rubber gloves fixed to ports in the walls enabled the machine to be operated from outside the box. A tray of magnesium perchlorate dried the air in the container and prevented both atmospheric corrosion fatigue at room and elevated temperatures and troublesome ice build-up at low temperatures. A total of ten to fifteen specimens was used for each combination of alloy composition and temperature. The result of each test was plotted on a standard S-N diagram, and the next stress was selected on the basis of the trends indicated by previous specimens. In this manner a small portion of the S-N diagram was constructed, and the 105 cycle fatigue stress obtained. Small Krouse fatigue specimens were also used to study the effect of cyclic prestrain on subsequent

Jan 1, 1964

By P. Bardzil, J. Gurland

An experimental study of the variation of transverse-rupture strength with composition Anexperimentaland grain studysize has shown that the strength reaches a maximum for values of the mean free path between carbide particles of 0.3 to 0.6 microns. The fracture oforiginates in and proceeds through the carbide grains mainly. Impact strength and hardness also were recorded. MOST of the physical properties of sintered carbides vary linearly with composition. The transverse-rupture strength, however, shows a unique behavior. As the amount of binder metal is varied from 6 to 25 pct by weight, the strength at first increases; then, between 15 and 20 pct Co, it reaches a maximum of nearly 400,000 psi, and finally decreases with further additions of binder metal. This behavior of the transverse-rupture strength has been reported, among others, by Englel and Sandford and Trent.' The significance of these observations has not been discussed in the literature. That it may be of more than specific importance is indicated by the very similar variation of strength with composition encountered in other systems sintered in the presence of a liquid phase, such as Tic-Ni3 and Fe-Cu.' Experimental Details All compacts were prepared and sintered according to normal industrial practice. The average diameter of WC grains and the mean free path between grains were measured on metallographically prepared samples by a method of linear and planar analysis sing the relations where d is the average diameter of dispersed grains; Nl is the number of noncontiguous grains intersected on a metallographic plane by a line of unit length; N, is the number of noncontiguous grains per unit area; P is the mean free path between grains of dispersed phase; and f is the volume fraction of dispersed phase. Approximately 1000 grains were counted on each sample. For each composition d2 was plotted against P, the resulting straight lines serving as a check on the measurements. The distribution curves of the WC powders of different average diameters were homologous, and no attempt was made to influence the grain size by blending powders, adjusting the sintering conditions, or otherwise altering the particle size distribution. Densities were measured by differential weighings in air and water. The degree of densification did not vary consistently with either composition or grain size. The density is influenced by slight amounts of impurities, specifically by 0.1 to 0.2 pct Fe which enters the powders during ball milling. As an illus- -tration of the experimental variations, a number of measured densities are listed in Table I. They are expressed in percentage of theoretical density, as calculated from the published X-ray densities of WC and Co.' For the purpose of determining the transverse-rupture strength, rectangular test specimens (3/16x 3/8x3/4 in.) were broken by loading at the center of a 9/16 in. span. The average strength of five or more samples is reported for each composition and grain size. The compacts were ground on two parallel surfaces only. The load was applied at an average rate of 6,800 psi per sec. Since the elongation after fracture of the alloys is very small, it was assumed that the compacts deform elastically to failure and the fracture stress was calculated by the conventional beam formula. The data for one alloy are presented in Table II as an example of the results and scattering ranges encountered. The precision of the test, as measured by the average difference between duplicates, is of the order of 15,000 psi. The results are strictly comparable only to compacts prepared and tested in the manner described and of similar chemical composition and grain size characteristics. Unnotched Charpy specimens were used for impact testing. Each point represents the average of 3 to 20 samples, the larger number being used in an attempt to determine the influence of grain size. Considerable scatter was encountered, the range from lowest to highest value often amounting to 30 pct of the impact strength. The hardness is reported as a Ra reading, using a 60 kg load with diamond brale indenter. Compositions are given in weight percent.

Jan 1, 1956

By S. Dinda

A series of as -quenched 4340 bars were drawn through a carbide die to various reductions. The X-ray diffraction technique of Lopata and Kula was employed to detect preferred orientation in drawn martensitic steel bars with low amounts of deformation, as lord as 0.8 pct The specimen face of each bar examined was cut at a 45-deg angle to the bar axis. The reflecting planes in the 45-deg face were varied by appropriate rotation of the sample using a spectrogonionzeter. TIE X-ray bean of a diffractometer was reflected from the center of the bar and the diffracted intensity was delected with a proportional counter and recorded. Intensity peaks were developed by cold working for 110 planes oriented at 0 and 60 deg to the bar axis. The intensity peaks increased with increasing defortnalion us a preferred orientation with a 110 texture developed parallel to the drawing direction. The intensity peaks for deformed as-quenched specimens remain unchanged after tempering at temperatures as high as 1000°F. The same amount of preferred orienlalion was observed both inferritic (hot-rolled) and martensitic (as-quenched) structures after an equivalent amount of deformation. THE deformation of martensite with medium carbon content. less than 0.5 pct, has been studied by Breyer et a1.1,2 It was reported that changes in properties such as resistivity, carbide precipitation, and the introduction of a yield point phenomenon were produced after cold reduction of as-quenched AISI 4340 steel bars. Later, Breyer and Nachtman3 studied the effect of cold reduction upon X-ray line intensity. They showed that the integrated 110 line intensity increased with increasing deformation when the planes examined were perpendicular to the die drawing direction. The integrated 110 line intensity for planes oriented at 45 deg to the die drawing direction, in contrast, were found to slightly decrease. These changes were proposed to be consistent with the previously proposed model of a stress-induced ordering of carbon atoms in the vicinity of dislocations.1,2 Objections can be raised to the above interpretation of the X-ray results on two grounds: a) Rough structure factor calculations indicate that the intensity changes are too large (50 pct observed vs 2 pct calculated4,5) to be the result of changes in the location of iron atoms produced by the stress-induced ordering of the carbon atoms. b) The results might be explained in terms of preferred orientations, although X-ray evidence of the development of texture has not been reported in the literature for deformations as slight as 1 or 2 pct. The aim of the present work was to determine if preferred orientation was present in such cold-drawn martensitic steel bars. In drawn rod or wire there is generally a certain crystallographic direction which is aligned in the direction of the wire axis, and the crystallographic planes are distributed symmetrically around this "fiber axis".6-8 This type of cylindrical specimen, with the fiber axis located at the center, will show rotational symmetry. Lopata and Kula9 proposed an experimental method utilizing a specimen cut at 45 deg, see Fig. 1. The X-ray beam is diffracted from the center of this bar cross section. The specimen is rotated around an axis perpendicular to the bar axis and lying in the 45-deg cut face. This permits the angle between the normals to the reflecting planes and the bar axis to be varied from 0 to 90 deg.9 With this arrangement the errors due to absorption and irradiated volume compensate each other.' This greatly simplifies analysis of the data and is of considerable advantage for quantitative measurements. If there is preferred orientation in the specimen, more planes are oriented in a particular direction in the bar. When the bar is rotated to the favorable Bragg condition for that particular orientation, the intensity will be higher than that for some other angle. This technique was adopted for the present investigation.

Jan 1, 1969

By Norman Ketzlach

Manganese Products, Inc. has developed a chemical process for the recovery of high-grade manganese oxides from low-grade manganese ores. Ammonium sulphate is also produced. Manganese ore is leached with sulphurous-sulphuric acids. The impurities are removed with ammonia, heat, and air. Manganese oxides are produced by addition of more ammonia and air under pressure. Ammonium sulphate is recovered from the remaining solution.

Jan 3, 1950

By John H. Schemel

Large Zircaloy-2 hammer or press forged bars did not exhibit the uniform excellent corrosion resistance to steam normally expected of the alloy in wrought form. Weight gains of coupons cut from forged bars were 40 to 60 mg per sq dm compared to the 28 mg per sq dm obtained on hot rolled sheet and strip. The mechanism of this corrosion and its relation to microstructure is discussed. After these observations, a solution heat treatment followed by rapid cooling was tried on coupons from eight heats of forged bars. The basket-weave structure resulting from the quench did not show agglomeration of intermetallic compounds. These coupons showed uniformly good corrosion resistance with weight gains very close to the 28 mg per sq dm expected of Zircaloy-2 after the 14-day steam test. A large forging was solution heat-treated and tested for structure, mechanical properties, and corrosion resistance. Corrosion resistance was excellent and uniform throughout the section. The normally anisotropic mechanical properties were changed to completely iso-tropic. Strength levels were raised while there was a small loss in ductility at the service temperature. Tempering of the quenched structure below the ß transus did not improve the ductility at the test temperature of 600°F. ZIRCALOY-2 end caps for nuclear fuel elements Zircaloy-2 is an alloy of 1.5 pct Sn, 0.1 pct Fe, 0.1 pct Cr, and 0.05 pct Ni, balance hafnium-free zirconium patented by Westing-house Electric Co. used in pressurized water reactors are machined from large hammer-finished forged bars. The bars forged for this application range from 3 1/2 in. to 7 1/2 in. squares. One of the tests used to evaluate Zircaloy-2 for this service is a 14-day exposure to very high-purity steam at 75oF and 1500 psi pressure. Normally wrought products will exhibit a black lustrous film of zirconium oxide after the test and show a weight gain of approximately 28 mg per sq dm. Coupons representing the forged bars exhibited a wide variety of corrosion results ranging from acceptable black coupons to some covered with white crystals of zirconium oxide that had weight gains of nearly 100 mg per sq dm. One of the most common effects was a white corrosion product that looked like a stain to some observers and the outline of massive metal grains to others. Very careful specimen preparation prior to the corrosion test did not affect the result and metallographic examination did not reveal a structural feature of a size and shape that would correlate with the corrosion product. In addition to the relatively poor corrosion resistance, the forged product was not as ductile as desired. The problem of obtaining uniform and more acceptable properties in these heavy-forged sections seemed to be a function of the microstructure of the metal and, in particular, the distribution of the intermetallic compounds. None of the four alloying elements however are appreciably soluble in a zirconium and are present as compounds which usually appear scattered randomly throughout the structure. Moudryl showed that the distribution of these intermetallic compounds in Zircaloy could be related to a ostringero corrosion failure. Grozier et al. discussed another structural defect that causes a similar corrosion effect. In this case, an elongated gas-void was determined to be the cause. M. L. Picklesimer held in his discussion of the Grozier paper that at least a part of the observed =stringersn were caused by the distribution of the intermetallic compounds. He proposed a

Jan 1, 1962

By R. G. Weavind, R. S. Young, I. Wolf

ONE of the most important fields of investigation at the Diamond Research Laboratory in Johannesburg is concerned with improvements in metallurgical practices for the diamond mining companies, with particular reference to increased recoveries of the smaller industrial stones. Considerable work has been done on the possible application of flotation processes to the diamond industry. From the viewpoint of recovery processes, diamonds in their natural state may be grouped into two classes, the water-repellent diamonds, which adhere to a grease surface, and the water-avid diamonds, which, because of their wettability, will not adhere to a grease surface and must be recovered by means other than the grease tables used for water-repellent diamonds. Experiments in the flotation of small diamonds from both kimberlite and alluvial deposits indicate the following conclusions: Water-repellent diamonds: Satisfactory flotation of —16 mesh diamonds, which are naturally water-repellent, may be accomplished using either Aero-float 25 together with cresylic acid, or Du Pont B23 as frother together with kerosine as auxiliary oily conditioner or froth stiffener. The quantities of reagents required are of the order of 0.15 lb per ton Aerofloat and 0.18 lb per ton cresylic acid. The use of acid circuits is detrimental, and for best results a pH between 7 and 9 should be maintained. R. G. WEAVIND and I. WOLF are with the Diamond Research Laboratory, Johannesburg, South Africa, and R. S. YOUNG, Member AIME, is Director of Research, Diamond Research Laboratory. TN 76B. Manuscript, March 23, 1951. A flotation period of 5 to 10 min is necessary to insure that all floatable diamonds are removed. Diamonds larger than 16 mesh cannot be recovered satisfactorily by flotation. Xanthates do not act as collectors for diamonds, and this is probably associated with their inability to impart a water-repellent surface to this mineral. Water-repellent diamonds smaller than 28 mesh can be floated quite well by the addition of a frother alone, such as pine oil or Du Pont B23. Water-avid diamonds: Partial flotation of the smaller sizes of wettable diamonds can be achieved by preconditioning with fatty acid soaps, cationic amines, and similar reagents, which will impart a water-repellent film to diamonds. Washing to remove excess reagent, followed by flotation, will result in a fair recovery, but the latter is much lower than for water-repellent diamonds. Crushed boart: Recovery of crushed boart from the waste products of industrial uses is best accomplished by first conditioning the diamonds present in the mixture with fatty acids, cationic amines, etc., removing the conditioning agent by washing, and floating in a cell of the pneumatic type. Flotation reagents found to be most suitable are Du Pont B23, and Aerofloat 25 together with cresylic acid. The optimum quantities are 1.2 g Du Pont B23, and 0.55 g Aerofloat plus 1.4 g cresylic acid, per liter of pulp in the cell. A solids-to-water ratio of 1 to 4 is found to be the most suitable, and alkaline circuits are necessary for best results. Diamonds larger than 28 mesh are not recovered satisfactorily by this procedure, but for finer sizes flotation offers an excellent procedure for the reclamation of this strategic industrial material.

Jan 1, 1952

By C. E. Silverblatt, D. A. Dahlstrom

Previous bench-scale studies demonstrated that a substantial moisture reduction can be obtained by the application of steam to coal filter-cakes, particularly to those containing a limited amount of minus 200-mesh material. Consequently, U.S. Steel's Applied Research Laboratory conducted a study to determine the feasibility of steam filtration of 1/4 in. by 0 coal on a continuous pilot-scale installation in which an Eimco extractor is used. The test results showed that the moisture content of this coal could be reduced to 5.5% at a steam loading of about 175 lb of steam per ton of dry cake. In terms of steam consumption, this loading is calculated to be 1-1/2 lb of steam per lb of water removed. In some tests, only 1 lb of steam per lb of water removed was required. These levels of steam consumption are significantly less than the actual heat requirements of conventional thermal dryers. The satisfactory moisture reductions were obtained at filtration rates of 125 to 186 lb of dry solids per sq ft per hour. However, the proper design of commercial filters should improve the potential rates that can be attained. These results indicate that steam filtration has considerable economic potential for drying 1/4 in. by 0 coals and also has additional advantages over the conventional thermal drying of coal. The results of the previous bench-scale studies and those published by Burton' demonstrated that a substantial moisture-content reduction can be effected by the application of slightly superheated steam to coal filter-cakes, particularly to those containing a limited amount of minus 200-mesh material. Consequently, US Steel's Applied Research Laboratory conducted a study to determine the feasibility of steam filtration of 1/4 in. by 0 coal on a continuous basis. In the continuous process, the dewatering operation on the filter is conducted in stages. In the first, the bulk of the water in the feed slurry is removed by conventional mechanical dewatering on a portion of the filter before the steam is applied. In the second stage, steam is applied to the cake. The steam condenses and releases its latent heat, thereby reducing the viscosity of the remaining cake water; this reduced viscosity then facilitates further drainage and produces a cake of lower moisture content. Because of the availability of feed coal on a continuous basis and since steam was readily available from a low-pressure boiler, the Applied Research Laboratory selected for the test site a coal-preparation plant that cleans Pittsburgh Seam coal. A slurry of table and flotation coal in percentages as they occur normally was used as feed stock. Typical analyses of this slurry are shown in Table I. DESCRIPTION OF FILTER AND EXPERIMENTAL PROCEDURES An Eimco Extractor was selected for the evaluation of steam filtration in a continuous process. This unit was chosen because of its availability and its design features that permit relatively simple hood construction, instrumentation, and operation. A photograph of the Extractor is shown in Fig. 1. In the filter a cloth medium is used that travels horizontally and continuously with a grooved, rubber drainage belt. The total effective filter area was 12.5 sq ft. As the feed slurry flows by gravity from the feed box onto the medium,

Jan 1, 1964

By Gilbert Doan

AN extensive program of investigation is being carried out at Lehigh University in the study of arcs and arc welds of high-purity iron1, spon-sored by the Engineering Foundation. The part of that program reported in the present paper deals with welds made of high-purity iron in an argon atmosphere and for comparison with them welds made of the same iron in ordinary air. Welds of commercial steel also were made in argon and in air. The primary purpose of the study is to discover the basic physical constants of iron welds when not contaminated either by impurities in the iron or by the action of oxygen and nitrogen of the air during welding. Upon these constants can be founded such future studies as will determine what effects the various impurities and alloy elements present in steel have upon its welding characteristics, and what influence is exerted by the action of oxygen and nitrogen. The welding of steel involves such a multitude of variables, both of composition and of procedure, that development in the fabrication of this most important metal has necessarily been slow, wasteful, and in many instances discouraging. In the present investigation, the simplest possible condition has been selected; namely, iron practically free from contamination and a nonparticipating atmosphere, the inert gas argon. This simplification reduces the number of variables to a point where more rigid control of the system is possible. Although this study is significant for the contributions it makes to the science of steel fabrication, yet it is hoped that it will not be without value also in increasing knowledge of the nature and behavior of iron and steel in general. From the standpoint of open-hearth practice, and to

Jan 1, 1936

By L. A. Wright, J. F. Emerson

The Pine Creek mine, owned by Union Carbide Nuclear Co., Div. of Union Carbide and Carbon Corp., is one of the world's largest producers of tungsten. The mine is located on the eastern slope of the Sierra Nevada Mountains, about 25 miles north- west of Bishop, Calif. Prior to 1948, production from the property came either from surface pits or from underground workings above A level haulage tunnel. The tunnel is at an elevation of 10,900 ft, which left 500 to 600 ft of vertical backs to the surface outcrops. Heavy production demands during World War II hastened the planning for long range development of orebodies below A level. A 7000-ft haulage tunnel, 1500 ft below A level, was started in 1943 and completed in early 1947. This haulage tunnel is at an elevation of 9400 ft and is known as Zero tunnel.

Apr 1, 1956

By L. R. Shoenberger

Boron has been used to produce nonaging low-carbon sheet steel. Retention of the necessary minimum amount of about 0.006 pet partially killed the steel. Amounts exceeding about 0.012 pet increased the degree of deoxidotion, piping tendencies, and possibility of hot tearing in primary rolling. Semikilled practice resulted in good ingot yields and satisfactory surface quality. Aluminum added with the boron provided a protective de-oxidizer. Good drawobility was indicated by performances of the steel in a limited number of deep-drawing trials. Some problems with hot-tearing and boron-analysis procedures were overcome. Metal lographically, the boron semikilled steels revealed some structures not usually found in plain low-carbon steels. IN 1943 Low and Gensamer1 reported that strain aging, which hardens and embrittles ordinary low-carbon rimmed steel, was due to nitrogen and carbon, and that oxygen played a relatively unimportant role. Since then, many investigators have substantiated their findings and indicated that nitrogen is particularly potent. Commercially, today's most widely produced non-aging sheet steels for deep drawing are either aluminum killed or vanadium rimmed types. The difference in deoxidation practice, alone, is evidence that oxygen is apparently not an important consideration in control of strain aging. The fact that nitrogen is important is apparent in the consideration that has been given, knowingly or unknowingly, to the amount combined with aluminum and vanadium. Patents were granted to Hayes and Griffis2 for the processing of aluminum-killed steel, and to Epstein" for the manufacture of vanadium rimmed material. Certain prescribed steps in producing these steels can be correlated with the formation of the respective nitrides within certain temperature ranges below the usual hot-finishing temperatures. The potential nonaging properties of either type can be reduced or suppressed by cooling too rapidly to permit the aluminum or vanadium to combine with nitrogen. Subsequent suberitical annealing of the cold-rolled strip, however, normally forms the nitrides and produces the resistance to strain aging. Titanium-killed nonaging steel, described by Comstock,1 forms a nitride in the molten state and is essentially nonaging throughout its processing. Zirconium-killed steel, which was investigated briefly by the author,* appeared to have similar nitride- forming characteristics. It is known" that chromium can produce nonaging rimmed steel, but relatively little is known of the potentialities of some of the other nitride-forming elements such as boron, silicon, columbium, and cerium. In attempting to develop a new nonaging cold-rolled sheet steel with good drawability, the following factors were considered pertinent. Such a steel would necessarily have a low carbon content and therefore have a relatively high degree of oxidation when made in a basic open-hearth furnace. If the denitriding element were also a deoxidizer, a part of the addition would be lost as oxide. The degree of deoxidation would determine whether the steel is rimmed, semikilled or killed, and also could be expected to have an important bearing on ingot yields and ultimate surface quality. Assuming that the pattern for the production of cold-rolled sheets would not be changed to any great extent, the nitride must form in the molten steel, in hot rolling, in subsequent cooling, or in annealing. The nitride, once formed, should resist dissociation and be stable in the final product. Usually an excess of the nitride-forming element is required to combine with sufficient nitrogen. If the element used is a strong ferrite strengthener, a small excess may markedly decrease drawability. With aluminum and vanadium, about 0.03 to 0.05 pct in the steel is preferred. Epstein has said" that about 0.30 pct chromium is required. Titanium nonaging steels are hard unless a sufficient amount (about 0.30 pct) is added also to combine with the carbon. The cost of the necessary amounts of these latter two elements discourages commercial acceptance. Silicon was considered as a possible nitride former, but since amounts up to 0.10 pct in rimmed and semikilled steels do not induce marked resistance to strain aging, larger amounts are apparently required, which would tend to harden and strengthen the ferrite. Of the other elements mentioned, all but boron are expensive heavy-metal elements. Stoichi-ometrically, almost an equal weight of boron would be required to combine with the nitrogen—-ordinarily about 0.003 to 0.006 pct in scrap-practice open-hearth steels. Boron is a slightly stronger deoxidizer than carbon but is less powerful than zirconium, aluminum, or titanium. Thus a rimmed-steel practice might be possible. There is much in the technical literature concerning the hardenability effects of minute amounts of boron in killed steels but very little about its behavior in low-carbon material—particularly as a ferrite strengthener. The available data indicated a need for better information concerning the effects of boron in low-carbon strip steels. Experimental Work Development of a Boron-Treated Nonaging Strip Steel—Initial attempts to produce a boron-rimmed strip steel employed 3-ton basic open-hearth heats which could be teemed into molds large enough to sustain a normal rimming action. Boron as ferro-boron was added to the ladle in small amounts because of the reported hot-short character of aluminum-killed heat-treating grades containing more than about 0.005 pct boron. Actually, the amounts used, i.e., 1/8 and 1/4 lb per ton, would be large for

Jan 1, 1959

By L. F. Mondolfo

R301 is a clad aluminum alloy, composed of a core of a duralumin-type alloy clad with a magnesium silicide alloy. It differs from other well-known clad alloys in that the cladding and the core respond to the same heat-treatments. and therefore the cladding contributes appreciably to the mechanical properties of the material. In Table I are reported the compositions of the core and cladding alloy for the material used for the experiments. Table i.—Chemical composition of R~OI Used for the Experiments Element Core Cladding Cu........................ . 0.01 Fe......................... . 0.42 Si......................... 0. 0.71 Mg........................ . 0.99 Mn ........................ . 0.54 In clad aluminum alloys where the core contains copper and the cladding does not, at elevated temperatures the copper tends to diffuse from the core through the cladding. This fact is well known and many investigations have been conducted to determine the features of this diffusion. Most of those investigations cover materials clad with pure aluminum; the present investigation covers a material clad with an alloy. Since the cladding thickness on R~OI varies with the gauge, as shown in Table 2, several gauges were investigated. Material and Procedure he material used was sheet of the following gauges: o.o2~, 0.040, 0.064, 0.102, 0.170 Cut in pieces approximately 3 by 5 in., it was in the cold-rolled state and was soaked for increasing times at the following temperatures: glo°F., 940°F., 970°F. A Lindberg cyclone furnace was used for the experiments. The procedure was as follows: The furnace was started empty with controlling pyrometer set at the determined temperature. After the furnace had reached that temperature, it was run for some 20 to 30 min. empty, in order to allow the temperature inside to become stabilized. Then the first samples were introduced. A load thermocouple, with recording pyrometer, was connected with the sample of the heaviest gauge. About 10 min. was required for the material to reach temperature and the soaking time was counted from that point. After zoo min. soaking, the second group of samples was introduced without stopping the furnace. After 200 min. more, the third group of samples was introduced, and so on, until the last sample had been introduced. Every time the furnace was opened and new samples were added, a drop of temperature was registered by the thermocouple connected with the material

Jan 1, 1946

By L. F. Mondolfo

R301 is a clad aluminum alloy, composed of a core of a duralumin-type alloy clad with a magnesium silicide alloy. It differs from other well-known clad alloys in that the cladding and the core respond to the same heat-treatments. and therefore the cladding contributes appreciably to the mechanical properties of the material. In Table I are reported the compositions of the core and cladding alloy for the material used for the experiments. Table i.—Chemical composition of R~OI Used for the Experiments Element Core Cladding Cu........................ . 0.01 Fe......................... . 0.42 Si......................... 0. 0.71 Mg........................ . 0.99 Mn ........................ . 0.54 In clad aluminum alloys where the core contains copper and the cladding does not, at elevated temperatures the copper tends to diffuse from the core through the cladding. This fact is well known and many investigations have been conducted to determine the features of this diffusion. Most of those investigations cover materials clad with pure aluminum; the present investigation covers a material clad with an alloy. Since the cladding thickness on R~OI varies with the gauge, as shown in Table 2, several gauges were investigated. Material and Procedure he material used was sheet of the following gauges: o.o2~, 0.040, 0.064, 0.102, 0.170 Cut in pieces approximately 3 by 5 in., it was in the cold-rolled state and was soaked for increasing times at the following temperatures: glo°F., 940°F., 970°F. A Lindberg cyclone furnace was used for the experiments. The procedure was as follows: The furnace was started empty with controlling pyrometer set at the determined temperature. After the furnace had reached that temperature, it was run for some 20 to 30 min. empty, in order to allow the temperature inside to become stabilized. Then the first samples were introduced. A load thermocouple, with recording pyrometer, was connected with the sample of the heaviest gauge. About 10 min. was required for the material to reach temperature and the soaking time was counted from that point. After zoo min. soaking, the second group of samples was introduced without stopping the furnace. After 200 min. more, the third group of samples was introduced, and so on, until the last sample had been introduced. Every time the furnace was opened and new samples were added, a drop of temperature was registered by the thermocouple connected with the material

Jan 1, 1946

By D. T. Peterson, T. Carnahan

The diffusion coejTicients of carbon, nitrogen, and oxyget were determined in $ thorium over the tempernilcre range 1440" io 1715°C. The diffusion coyfiicir?zls are given by: D = 0.022 exp (-27,000/RT) jor carbo)~, D = 0,0032 exp(-l7,00Q/RTj for nitrogen, and D = u.0013 expt(-11,UOU/RT) for oxygen. Cavl~orz was found to increase the hardness of thoriunz nearly linearly with concentration over the range 100 to 1000Ppm carbon. ThORIUM has a fcc structure up to 1365°C and a bcc structure from this temperature to its melting point at 1740°C. Diffusion of carbon, oxygen, and nitrogen in bcc thorium was of interest in connection with the purification of thorium by electrotransport.' In addition, it was possible to measure the diffusion of all three of these interstitial solutes in the same bcc metal. Only in niobium, tantalum, vanadium, and a iron have all three interstitial diffusion coefficients been measured in a given bcc metal. Diffusion coefficients have been measured for carbon and oxygen in a thorium by Peterson2, 3 and for nitrogen by Gerds and Mallett.4 Activation energies for diffusion are reported by the above authors to be 38 kcal per mole for carbon, 22.5 kcal per mole for nitrogen, and 49 kcal per mole for oxygen. Values of the diffusion coefficients of carbon and nitrogen in 3 thorium have been reported by Peterson et al.' However, these were secondary results of their investigation of electrotransport phenomena in thorium and it was hoped that the present study could provide more precise data. EXPERIMENTAL PROCEDURE The specimens used in this study were the well-known pair of semi-infinite bar type. The couple was formed by resistance butt welding two 0.54-cm-diam by 3.0-cm-long bars of thorium together under pure helium, the concentration of the solute being greater in one cylinder than that in the other. The finished couple then contained a concentration step at the weld interface and diffusion proceeded only along the axis of the rod. The thorium used in this study was prepared by the magnesium intermediate alloy method.5 The total impurity content was less than 400 ppm. The major impurities were: carbon, 100 ppm: nitrogen, 50 ppm; and oxygen. 85 ppm. The total metallic impurity content was less than 150 ppm. The high solute concentration portions of the diffusion couples were prepared by adding the solute to the high-purity thorium in a non-consumable electrode arc melting procedure. Carbon and nitrogen were added in the form of spectroscopic graphite and nitrogen gas while a Tho2 layer was dissolved by arc melting to add oxygen. High-purity thorium formed the low concentration portions in the carbon and nitrogen couples. The low oxygen portions were obtained by deoxidizing high-purity thorium with calcium for 3 weeks at 1000°C according to a method reported by Peterson.3 The high C-Th contained 400 ppm C, the high N-Th contained 400 ppm N, the high 0-Th contained 220 ppm 0, and the low 0-Th contained 25 ppm O. The high O-Th was brine-quenched from 1500°C to retain most of the oxygen in solution at room temperature. These concentration levels were all below the solubility limits in 0 thorium at 1400°C. A resistance-heated high-vacuum furnace was used to heat the couples. The samples were mounted horizontally on a tantalum support which had small grooves near each end. Spacer rods of thorium, 0.4 cm in diam, were placed in these grooves to prevent contact between the sample and the tantalum support. This arrangement should have prevented contamination of the sample by contact with the support. In further effort to reduce contamination, the oxygen diffusion couples were sealed inside evacuated outgassed tantalum cylinders lined with thorium foil. Thorium rings around each end of the samples acted as spacers in this case. Pressure during diffusion runs was about 10-6 torr after an initial outgassing stage. Temperature measurements were made by sighting on black body holes in the sample support adjacent to the samples with a Leeds and Northrup disappearing-filament optical pyrometer. Temperatures were constant during a diffusion anneal to ±5C. The observed temperatures were corrected for sight glass absorption after each diffusion run. The pyrometer was checked against a calibrated electronic optical pyrometer and a calibrated tungsten strip lamp with the electronic pyrometer being taken as the standard. All temperature readings agreed to within ±3C over the temperature range 1450" to 1690°C. Time corrections due to diffusion during heating and cooling were necessary because of the short diffusion times. The diffusion times ranged from 6 min for the oxygen sample run at 1690°C to 90 min for the carbon sample run at 1500°C. A series of temperature vs time plots were made for heating and cooling of the samples to the various diffusion temperatures. This data was then used in a method according to shewmon6 to determine the time corrections. The corrections amounted to

Jan 1, 1970

By R. G. Davies

The activation energy for steady state creep above -500°C is observed to be independent of the applied stress although it varies from -67 kcal per mole at 2 at. pct Si to -100 kcal per mole at 11 at. pct Si due to changes in crystallographic order. The magnitude of the activation energy, by comparison with Fe-A1 alloys, indicates FeSi type of order in certain alloys. X-ray results confirmed the presence of FeSi type of order. It is proposed that dislocation climb is the rate controlling mechanism for all the alloys. It has been demonstrated that when a diffusion mechanism is the rate controlling process, the formation of a superlattice in brass,1 Fe3A1,2 Ni3Fe,3-5 and Feco6 1) increases the creep resistance, and 2) increases the activation energy for steady state creep. Furthermore, a study of creep in Fe-15 to 20 at. pct A1 alloys7 has revealed that as the alloy composition approaches the long-range order field, there is an increase in the activation energy for steady state creep which is thought to be due to an increase in short range order. Fe-A1 and Fe-Si alloys are similar in that they both form the DO3 superlattice in which aluminum or silicon atoms have only iron atoms as first and second nearest neighbors. There are, however, two important differences between the alloy systems: 1) The superlattice formation at -350°C commences at -10 at. pct si8 as compared to -20 at. pct Al,9 and 2) Fe-A1 alloys form a FeAl (B2 type) super-lattice where aluminum atoms have all iron first nearest neighbors even at 22 at. pct Al, but so far no similar FeSi superlattice has been observed. With the similarity between Fe-A1 and Fe-Si alloys in mind, alloys of iron with 2 to 11 at. pct Si were examined for variations with composition of the activation energy for steady state creep and of creep strength. The temperature range of greatest interest was above 1/2 TM (TM is the absolute melting temperature) where it is usually observed that diffusion is the rate controlling process. A subsidiary X-ray investigation of the Fe-Si system was undertaken in an attempt to define the position of the order-disorder boundary as a function of cooling rate. EXPERIMENTAL DETAILS a) Creep. Specimens whose gage length was 1.5 in. and with a cross-section 0.04 by 0.08 in. were strained in tension by a lever-arm arrangement, and the load was adjusted between each creep test to maintain constant stress. The apparatus and mode of operation have been fully described in a previous publication.7 As each test produced a creep strain of 0.25 pct, the variation in stress during the test was negligible. Creep strain was measured at the end of one of the alloy steel grips by a displacement transducer with the out-of-balance potential being recorded on a variable speed recorder. The full-scale deflection of the recorder could be varied in steps to give limits of sensitivity of between 0.1 and 0.001 pct creep strain. The alloys, Table I, were made available by the Metallurgical Department, National Physical Laboratory (N.P.L.), england,10 and by the Research Department, General Electric Co. (G.E.), Schenectady, N.Y. They were hot worked at -850°C, warm worked at 550° to 650°C, and recrystallized in vacuum at -750°C to give a grain diameter of -0.1 mm. All the alloys had a very low impurity content; those from the N.P.L., for which a complete analysis is available,&apos;&apos; show carbon less than 0.026 pct, manganese less than 0.006 pct, and oxygen plus nitrogen less than 0.0024 pct. b) X-ray Procedure. A General Electric XRD-5 X-ray set with a focussing lithium fluoride mono-chromator in the diffracted beam, and a pulse height analyzer to eliminate harmonic wavelengths of the cobalt radiation, was used to investigate the structure of several very fine grained (grain diameter <.01 mm) Fe-Si alloys after the following heat treatments: 1) Quenched from 700°C, 2) slow cooled from 650°C (-40°C per hr), and 3) very slowly cooled from 400° to 100°C (10°C per hr with a 24 hr anneal every 100°C). The method of obtaining the diffraction pattern over the range of 20 from 15 to 45 deg was to count for at least 100 sec every l/3 deg with a slit subtending 1 deg in 20 at the focus; the probable counting error was less than 2 pct.

Jan 1, 1963

By H. H. Podgurski, H. E. Knechtel

Annealed Fe-Al alloys do not react readily to form AlN when held at 500ºC in NH3-H2 gas mixtures, but do so upon the introduction of dislocatims. Nuclea-tion of the nitride phase occurs on dislocation sites. In turn, the growth of the aluminum nitride particles causes the ferrite phase to yield plastically, generating more dislocations for the nucleation process. The nitride phase extracted from an Fe-2 pct A1 alloy nitrogenated at 500°C was identified as stoichio-metric aluminum nitride with a hexagonal crystal lattice. THIS investigation reveals the role that dislocations play in initiating and sustaining the nitriding reaction in Fe-A1 alloys. As early as 1931 the work of Meyer and Hobrock1 suggested that the initiation of the nitriding reaction could involve a nucleation controlled process. Recently Bohnenka2 depicted the gas-phase nitriding process below 600°C as one of mixed control limited by nitrogen penetration through the surface, by nitrogen diffusion, by aluminum diffusion, and by nucleation of the nitride phase, Fig. l(a). In our research in a comparable alloy (0.57 pct Al) at 575ºC, we have observed a nitrogenation which we feel is better described by Fig. l(b). In the case of a 2 pct-A1 alloy partially nitrided at 500°C we propose the profiles shown in Fig. l(c). For a complete and accurate description of the process, a concentration profile of the dislocation density in the test specimen would be needed. EXPERIMENTAL Nitrogenization was conducted between 500" and 575°C in a variety of NH3-H2 gas mixtures on three Fe-A1 alloys: 1) zone-refined iron + 0.16 i 0.2 pct Al—levita-tion melt, 2) zone-refined iron + 0.57 0.02 pct Al— levitation melt, 3) plastiron + 2 pct Al—melted by induction heating. To demonstrate the effect of dislocations on reactivity, both cold-worked and annealed samples were investigated. All nitrogenation rate studies were conducted gravimetrically with a gold-plated invar balance4 contained in a gas-flow system. To avoid contamination of the specimens in the reaction zone of the system, the reaction chamber was constructed of high-purity dense alumina. The activity of nitrogen was fixed by specific NH3-H2 gas mixtures whose compositions were continually monitored by calibrated thermal conductivity gages and checked by chemical analysis. Variations of ± 0.1 pct NH3 could easily be detected by both methods. Throughout this paper the activity of nitrogen is defined as PN3 /PH23/2 , where PNH3, and Ph2 are partial pressures in atmospheres. Electron transmission, density measurements, and chemical analyses were made on specimens before and after nitrogenating in order to reveal structural and chemical changes. Similar studies as well as X-ray diffraction studies were conducted on nitride extractions from the nitrogenated 2 pct-A1 alloy. These extractions were obtained by the use of an anhydrous bromine-methyl acetate solution which dissolves the iron and leaves the insoluble nitrides as a residue. Hardness profiles were obtained on cross-sections of partially nitrided specimens to demonstrate the extent of nitriding through the thickness of the specimens. RESULTS AND DISCUSSION The nitrogen activity in the NH3-H2, atmospheres was never allowed to reach a level capable of producing iron nitride (Fe4N). Hence, the term nitriding as used in this paper refers only to the formation of aluminum nitride whereas nitrogenation refers to the total uptake of nitrogen regardless of how it is distributed throughout the alloy. The weight increases observed during the initial stage of a nitrogenating treatment are due primarily to the solution of nitrogen in the ferrite phase, particularly when starting with annealed specimens. Because this initial nitrogenation rate in the case of the 0.57 pct A1 alloy, see Figs. 2 and 3(a), was most rapid the weight change that occurred thereafter might be attributed to the nitriding reaction with the exception of a small weight increment due to the irreversible pickup of oxygen by aluminum. The oxygen (<70 ppm) came from traces of H2O and 0, in the hydrogen and ammonia gases. On the basis of discrepancies between total weight increase and the increase in the nitrogen content of the sample as determined by chemical analysis, it was estimated and later established by activation analysis, that as much as 200 ppm of oxygen were taken up by a fully nitrided Fe-0.57 pct A1 specimen at 575°C. Most of the oxygen could have been picked up from the nitriding atmosphere on the surface of the samples during cooling to room temperature. Even 50 ppm of water in the gas phase will become oxidizing to iron before the sample has cooled to room temperature. The lack of reactivity* of these alloys in the annealed

Jan 1, 1970