Search Documents

By Robert G. Van Nostrand, John H. Henkel

TRANSIENT potentials obtained in resistivity prospecting can be separated into two classes. The first is electromagnetic, has a comparatively short time constant, and increases in relative amplitude as the electrode separation is increased. These electromagnetic transient potentials, of which an excellent theoretical treatment is given by Yost: are the result of changes in the current and can be classed as differentiated signals. The second class is electrochemical, has a comparatively long time constant, and decreases in relative amplitude as the electrode separation is increased. The electrochemical signals are generated by the current flow itself and can be classed as integrated signals. The transient potentials due to electrochemical factors are the subject of this article. The phenomenon is referred to as induced polarization. Schlumberger" was the first worker to observe induced polarization, but he was unsuccessful in attempts to apply the principles of induced polarization in electrochemical prospecting. Other workers, notably Bleil; have studied polarization and in some cases pointed out its possibilities, but no theory has been presented that describes polarization and its time dependence adequately. It is the purpose of this discussion to present the essence of a theory to geo-physicists and to show that it leads to results consistent with experimental evidence. The theory on which this analysis is based has existed in electrochemical circles since 1910."

Jan 1, 1958

By D. D. Pollock, D. I. Finch

PREVIOUS work' on a four-component system (Cu-Mn-Ni-Fe) resulted in the development of consistent relationships between the chemical composition and the electrical properties of these manganin-type alloys. The present study was undertaken to develop alloys with temperature coefficients of resistivity and thermoelectric properties more desirable than those of the manganin type, and to determine whether the relationships which had been found for the Cu-Mn-Ni-Fe alloys could be extended to five-and six-component alloy systems. PREPARATION OF ALLOYS The five- and six-component alloys were made from OFHC copper rod, ARMCO iron, electrolytic nickel, manganese cathode chip, and special high-purity aluminum and indium. A Cu-Mg master was used for deoxidation. The compositions of these materials are given in Table I. The alloys were melted and cast as indicated previously,' except that no cover was used and the melts were teemed. EXPERIMENTAL PROCEDURE The finished wire size of 0.0808 in. diam was again selected for the reason that the test specimens would be self-supporting, thus eliminating any extraneous effects which might have been introduced by winding smaller diameter wire on spools or forms. The following tests were performed on the finished wires: A) Chemical Analyses—All of the components of these alloys were determined by premium gravimetric methods. The principle residual impurity contained in these alloys is 0.008 pct Mg (by weight), maximum. Tables II and 111 present the mean analyses computed from at least four determinations of each constituent. B) Electrical Characteristics—The test procedures forthe determination of the thermal emf vs copper, resistivity, and the resistance-temperature relationship are given in detail in Ref. 1. It was also shown that the resistance-temperature relationship is of the form Pt = P,n + At -B/2, [1] where P, is the resistance at t C expressed in percent of a given standard resistance, P, is this per- 0 centage at 0°C, and A and B are constants for a given, properly treated, composition. The results of the electrical tests are also given in Tables II and 111. INTERPRETATION OF DATA The modified Linde2 formula, known to be valid for dilute binary solid solutions, was applied to the complex Cu-Mn-Ni-Fe type alloys. This relationship is of the form where Ap is the increase in resistivity. Zb the valence of the solute, Zn the valence of the solvent, and K and K are designations assigned by Robinson and Dorn3 to the constants for the periodic group to which solute element belongs. The units of K, are -cm per valence difference squared per at. pct; those of K2 are pa-cm per at. pct. For the sake of brevity, these units are not repeated in the following discussion. Calculations were made to determine if this formula was accurate for five-component systems. No experimental studies were made of the Cu-In and Cu-A1 binary systems. The effects of indium additions upon the resistivity of copper are given by Linde. These data, along with those of the effects of Mn and Fe, permitted the calculation of the effects of Al.

Jan 1, 1959

By A. M. Gaudin, C. S. Chang

IN general, fatty acids or their alkali salts do not cause clean quartz to float. However, the presence of multivalent ions, such as the alkaline-earth metal ions and heavy-metal ions, can activate quartz and thus make it respond to soap flotation. The mechanism of activation and soap flotation of quartz has been studied.1-4 The problem was attacked by making flotation tests rather than by careful adsorption measurements on suspensions of ground quartz in solutions containing the activator and the collector. Attempts have been made to determine the adsorption of barium ion and calcium ion on quartz. The results have only qualitative value as the analytical methods were not adequately precise. Artificial radioactivity and progress in radioactivity detection have introduced a new analytical tool, which can have a sensitivity several orders of magnitude greater than that of other methods.5-6 In the experimental work described in this paper the radioactive tracers, barium 140 and carbon 14, were employed. Lauric acid was synthesized, having a radioactive carbon atom and was used with Ba140 to study the adsorption of barium and laurate ions from aqueous solution on ground quartz. Flotation tests, using the vacuum flotation technique,4 were run in conjunction with the adsorption experiments. The object of this investigation was to understand better the reaction mechanism of barium activation and soap flotation of quartz. Methods and Materials Quartz Sample Preparation: Lumps of hand picked quartz, washed free of stains, were reduced in size to -20 mesh in laboratory crushers. The product was boiled in concentrated hydrochloric acid to remove the abraded iron. The cleaned product then was ground dry in a laboratory porcelain mill, using siliceous pebbles, to pass through a 200 mesh screen. The ground product was deslimed by sedimentation at 37 microns. This -200 mesh +400 mesh material was subjected again to boiling with concentrated hydrochloric acid, followed by washing with distilled water and further desliming. The cycle was repeated until no trace of iron could be detected in the wash liquor. During the final washing, the pH of the wash water was checked to insure the complete removal of the acid from the mineral. The quartz then' was rinsed with conductivity water. The resulting product was dried in a drying oven and stored in mason jars. The impurities (spectrographic) were as follows: Al, 0.01 to 0.001 pct; Li, Mg, Mn,, Na, each less than 0.001 pct; Fe and Cu not detected. The specific surface of the quartz sample was determined by the krypton gas adsorption method.7 The average of two measurements was 881 sq cm per g. The calculated specific surface for 37/74 micron quartz particles, using a surface factor of 1.96,8 is 900 sq cm per g. This is in good agreement with the measured value of 881 sq cm per g. Beta-Counting Method: The radioactive isotope of barium used in the experimental work was barium 140. It has a sufficiently long half-life, 12.8 days, emits high-energy beta particles (up to 1.0

Jan 1, 1952

By H. K. van Poollen, H. C. Bixel

A treatment is given of the transient pressure behavior of a well located at the center of a circular region surrounded by a radial discontinuity. On either side of the discontinuity, the values of permeability, viscosity, compressibility and porosity are uniform but may be different from those on the other side of the discontinuity. The results are obtained by solving a pair of finite difference equations. The numerical solution to these equations is obtained using a digital computer. The results are compared with previously published, approximated analytical solutions to the same problem. Solutions, presented graphically, show pressure decline for constant rate fluid production. The range of variables studied include dimensionless time from '0.001 to 100 and storage capacity ratio from 0.001 to 1,000. The well behaves as if it were in an infinite reservoir for dimensionless times less than 0.25. Reservoir properties near the well can be estimated in the usual manner. An overlay technique is used to match an experimental curve with one of the theoretical curves. It is possible to estimate the distance to a discontinuity by substituting the actual time t and the corresponding dimensionless time tD at which a match occurs into the equation a = (0.000264 tk1/tD , µ1 cI)I/2 where kI/ I µI cI is the diffusivity near the well, and may be estimated from data taken at early time. Several buildup curves are computed. These curves show that for early shut-in times, correct values for transmissibility are obtained from conventional analysis. However, erroneous values of static reservoir Pressure are obtained unless data at large shut-in times are taken. INTRODUCTION A mathematical treatment of the transient pressure response of a well located at the center of a region bounded by a circular discontinuity is given. Within a region (Fig. 20) the properties of both the rock and the fluid are considered to be constant on either side of the discontinuity. While these properties are considered constant, they may be different on opposite sides of the discontinuity. A discontinuity of this type could be a fluid-fluid contact or a sudden change in rock characteristics such as thickness, porosity or permeability. Analytical solutions to this problem are available. 1-3 However, they are so involved that they are of little practical use. An approximate solutionl is available but the range of times over which it is valid has not been specified. A numerical solution to a pair of finite difference equations is used to obtain the solution given in this paper. PREVIOUS WORK One of the first solutions to the problem was published by William Hurst.1 Hurst considered unsteady-state flow of fluids through two sands in series with different mobilities in each sand. He used Laplace transforms to obtain a solution for a single well located at the center of the circle enclosing the first of the two sands. In this case, the solution for the pressure change in Region I (Fig. 20) is2

By William D. Klopp, Joseph R. Stephens

ThE phenomenon of high ductility associated with a phase transformation, termed super plasticity, has been reported for a number of alloy systems. Abnormally high ductility has been observed during tensile testing of cast eutectic alloys of Pb-Sn and Mg-cu.1 Brasses of Cu-37 at. pct Zn and Cu-40 at. pct Zn elongate up to 180 pct when tested near their transformation temperature.' Enhanced ductility was also observed in Cu-47 at. pct Zn tested near the order-disorder transformation temperature. The most remarkable super-plastic effect reported to date is for the eutectoid alloy A1-60 at. pct Zn, where elongations up to 1000 pct have been reported.3 underwood4 has recently summarized the conditions that normally accompany the superplastic effect which are: 1) a phase transformation or allotropic change or order-disorder transformation; 2) an externally applied stress; 3) presence of an interface between two phases; and 4) a metastable structural condition. In addition, higher ductility is observed when the specimen is tested at slow deformation rates rather than under impact. The purpose of this note is to present evidence of the superplastic effect in a Cr-30 at. pct Co alloy. In addition, low-temperature bend ductility data are given for the alloy in the quenched, metastable, single-phased condition and in the slow-cooled, two-phased, near-equilibrium condition. Sixty-gram alloy ingots were prepared by noncon-sumable arc melting of iodide chromium and electron-beam-melted cobalt. These were cast into rectangular ingots and fabricated to 0.035-in. sheet by rolling at 2300°F. Attempts to roll at slightly lower temperatures invariably resulted in severe cracking, apparently due to presence of the brittle a phase below the transformation temperature of 2230°F. Tensile specimens with a 0.25 by 1.0 in. reduced section were cut from the sheet by electrical discharge machining. The specimens were heated at 2400°F for 1/2 hr to obtain a recrystallized, bcc, single-phased structure. Temperature of the specimens was subsequently raised or lowered to the desired test temperature and held for 10 min prior to testing at a crosshead speed of 0.01 in. per min. Fig. 1 shows the chromium-rich side of the Cr-Co phase diagram.6 The alloy composition investigated is near the point of maximum solubility of cobalt in chromium, and the alloy is two-phased when in equilibrium at temperatures below 2230°F. The results of tensile tests conducted at temperatures indicated by X's in Fig. 1 are summarized in Figs. 2, 3, and 4. Tensile elongations shown in Fig. 2 increase from 11 pct at 1900°F to a maximum of 160 pct at 2250°F. The elongation then decreases to 44 pct as the test temperature is further increased to 2600°F. The proximity of the temperature of highest elongation and the solvus temperature suggests that a superplastic effect is present in Cr + 30 at. pct Co similar to that observed for other alloys that show anomalous ductility. The variation of upper yield stress with temperature is shown in Fig. 3. A small peak in yield stress occurs at 2250"F, coincident with the maximum in

Jan 1, 1967

By D. E. Trout, W. R. Hibbard

Previous investigations have shown that the cold rolling textures1n2 and the drawn wire textures3 of copper change their secondary components after the addition of about 1 pct aluminum and 5 pct zinc, but do not change after the addition of as much as 30 pct nickel. However, few data are available on compression textures. Barrett4 reports from unpublished work with E. L. Layland that compression rolled copper develops a texture which is predominately (110) in the compression plane with a secondary spread to (113) and weaker spread to (100) as shown in Fig 1. However, 70-30 alpha brass similarly treated develops a texture again predominately (110) in the compression plane and with a weak secondary spread to {113} but with moderate (111) secondary intensities illustrated in Fig 2. Experimental Procedure Specimens of the compositions shown in Table 1 remaining from a previous investigation3 were annealed to a grain size of 0.090 mm average diam and machined to cylinders 0.20 in. diam and 0.20 in. high. Cylinders were compressed 90 pct reduction in height between lubricated steel blocks in a tensile machine. Glancing X ray photo-grams using copper K-alpha radiation were taken at an angle of 0 degrees to the compression surface. (111), (002) and (220) rings were analyzed to define the textures shown in Table 1. The results are in agreement with Barrett4 as to types of textures and are essentially in agreement with previous work1,2,3 as to the effects of composition. In the wire study3 it was reported that the 4.99 pct zinc alloy had a brass-type texture, while the data in Table 1 indicate a copper-type texture for compression. The wire specimen of the 4.99 pct zinc alloy was re-examined by X rays and it was established that the [loo] component still exists in the wire axis. Therefore, Table 2 of Ref. 3 is in error and should indicate a double [ill], [loo] copper-type texture for this alloy. This correction results in complete consistency with regard to compositional effects, namely that copper and its alloys containing up to approximately 1 pet aluminum, 5 pct zinc and at least 30 pct nickels develop a copper-type texture and more concentrated copper-aluminum and copper-zinc solid solution alloys will form a brass-type texture. Summary Compression textures developed in copper and its alpha solid solution alloys of aluminum, nickel and zinc are essentially the same types as those re- ported by Barrett4 with compositional effects occurring at approximately the same percent additions as previously reported for rolled sheet182 and drawn wire.3 The Scovill Manufacturing Co., Waterbury, Conn., furnished the copper and brass alloys, performed certain chemical analyses and supplied laboratory facilities where needed. References 1. Brick, Martin and Angier: Tram. A.S.M. (1943) 31, 675. 2. Dahl and Pawlek: Zlsch. Melall. (1936) 28, 266. 3. Hibbard and Yen: Trans. AIME 175, 126. Melals Tech.. Feb. 1948, TP 2334. 4. Barrett: Structure of Metals, mc- Graw-Hill (19421, 386.

Jan 1, 1950

By Roberto Fernandez

Want of knowledge on the part of experts from abroad respecting the amalgamation-system, known as the Mexican or patio process, has been the cause in this country of trouble to many foreign mining companies. This process has not been looked upon by their managers as a satisfactory method of treating silver-ores, and they prefer to employ others, which, although more modern, and often more profitable in other countries, have not proved to be so under the exceptional conditions of this country, where labor is cheap and paid in silver, while fuel is very dear. The cause of this error of judgment is probably the inexact information which has been furnished by several authors respecting the economical results of the patio process. This treatment is not suitable for silver-ores of every kind. Simple sulphides of silver are best adapted to it, and, next to these, the combinations of complex sulphides, viz., pyrargyrite, polybasite, stephanite, proustite, etc. Chlorides, bromides and iodides of silver are considered rebellious ; argentiferous galena, blende, bournonite, as also argentiferous arsenical pyrites of iron and copper, are absolutelg unsuited to this treatment. Experience has proved that high-grade ores do not give as satisfactory results as those of mediurn grades, as, for instance, carrying from 1 to 2 kilos of silver per metrical ton. The patio process, as actually practiced in this district, comprises the following operations: 1. The ore is crushed in a dry state in a roller-mill, reducing it to pea-size, from which uniform samples, and, in consequence, correct assays, can be obtained. 2. It is then thrown into the arrastra, and pulverized with water, so fine that it will pass through an 80-mesh screen.

Jan 1, 1900

By Cleveland Dodge

THE present organization of Copper Queen employ-ees, known as the Employees' Conference Com-mittee, is really an outgrowth of the former Grievance Committee, which, in turn, had developed from the original Hospital Committee. The relatively small membership of these older organizations, the practical limitation of their activities to the presenting of grievances, and their lack of initiating powers, were the principal defects which the plan now in operation seeks to overcome. A somewhat parallel scheme was instituted in our Sacramento Hill division about four years ago; this gradually developed into the Ways and Means Committee, which, in addition to providing a forum for the discussion of operating problems, was instrumental in establishing an excellent and mutually satisfactory bonus system. Before recommending adoption of the plan now in force, we made extensive inquiries among those who have had any experience in such matters, and ended by proposing a modification of a scheme developed by John Leitch,1 which was characterized by its similarity to the constitution of the Federal Government. As finally remodeled, the. plan was submitted to vote of the entire working forces at the Copper Queen mines, and was adopted by them in May, 1920. Mining opera-tions since that date have been so interrupted that it is scarcely possible to state exactly what the results have been. The following quotations are from a printed pamphlet containing the constitution of the organization, as finally adopted. The first extract is from a letter addressed by the management to the employees: The plan submitted for your approval and adoption is modeled after the constitution of our own country, under which every individual is given an opportunity for advancement, according to his ability and determination, and every citizen is given a voice in the laws that shall govern him. So it is to encourage the individual employee in advancement, and to give him a voice in making the rules that shall govern his conduct, that we favor the adoption of the proposed constitution.

Jan 1, 1923

ZAY JEFFRIES (written discussion*).-I have read with much interest Mr. Ruder's discussion of Professor Howe's paper, "The Supposed Reversal of Inheritance of Ferrite Grain Size from that of Austenite." I am yet of the opinion that my first explanation' of Mr. Ruder's samples is substantially correct. In that explanation I did not intend, however, to convey the impression that "reversed inheritance" was the general rule nor even of common occurrence but rather that." Non-inheritance" was the general rule. Mr. Ruder suggests that a " perfectly formed" grain is an indication of inheritance. The grains in my Fig. 52 are perfectly formed and in fact more nearly equiaxed than those in Mr. Ruder's Fig: C,3 yet the grains in the former are known not to be inherited but to have been formed by the partitioning of larger austenite grains. On close examination of Mr. Ruder's Fig. C the very shapes of the grain suggest partitioning. Again, the grain size (25 to 30 grains per square millimeter) is at least 10 or- more likely 20 times smaller than might be expected of the austenite from which these grains were .formed under the given time and temperature conditions. Mr. Ruder's newer results on electrolytic and Armco iron are most interesting and instructive. His results fit in. nicely with my conclusions 5, 6 and 10.4 His photographs, however, indicate that the thickness of the pieces of sheet metal are such that abnormal grain growth is promoted. He indicates that equilibrium grain size after heating to 950° C., with furnace cooling, is about the same as his Fig. 1, above. I estimate this to be approximately one-half -grain per square millimeter, or 40 times as large as I have obtained with the same material (Armco iron) after heating Y4-in. bars to 1300° C. for 2 hr. and cooling in the furnace. The effect of thickness of sample on grain size is one which needs more attention.

Jan 3, 1918

By H. I. Aaronson, H. A. Domian, G. M. Pound

The thernodyna,nics of I the Proeutectoid ferrite re-action ha1.e been investigated on the bases of three diifevent descviptions of the statistical thernzodynamics of interstitzal solid solutions. Especially at low ternperatures, substantial dijeretzces are found in the valltes of the extrapolated y/y + a and cr/a + y equilibriurn curls, and in the To- co7nposilion metastable eqliilibriunz curl-es thus co,npited. Although neither actiztity nor phase-diagram date are able to distingrish udeqiutely among the various descviptions, the statustics of Lacher, Fouller, and Guggenheinz provide the ?nost conplete epresentation az3ailable of the single carbon-ctrbon interaction energy (w) nzodel of an intevstitiril solid solution, and the relationships deduced frojrl then2 are accordingly pre.ferred. The findings tlzut w in austenite 'aries significu?ztly uith tenpevntrue and that phase-diagawr data arc not accurately con?palible usith eqcrctions deduced on the basis of actility infoation indicate, hou'e13er, that a wzore cornplex nlodel of the uustenite , und pvobably of the .feyrite, solirl solutions will have to forn the basis of f4tuve statistical t1.eat1nents. Some suggestions for such a ruodel arc advanced. Althoug11 w represents a vepltlsio energy in austozite, it was found to corvcsporzd in ferrite to a binding energy, in qualitatit.e accord zc,itlz the internal-friclion results of Keefer and wert. ThE transformation of austenite to proeutectoid fer-rite is becoming recognized as an exceptionally useful vehicle for quantitative studies of the kinetics of phase transformations.'" Reasons for this popularity include well-characterized microstructures which develop on a convenient scale with acceptable kinetics within a considerable temperature-composition region, the absence of great sensitivity to common impurities, and, especially. the availability of a unique wealth of the ancillary information indispensable for the quantitative interpretation of kinetic measurements, including phase diagram,3 crystallographies diffusivity,5 inter-facial energy,=17 elastiit," specific vlume, ''' and ativity'-' data. Development of considerable amounts of additional thermodynamic information from activity data is of particular importance with respect to kinetic studies, since much of this information is needed in temperature-composition regions not directly accessible to presently available techniques for the measurement of equilibrium properties. A generally useful approach to the thermodynamics of solid solutions, which is of especial value in this situation, is based upon the formulation of the free energy of such solutions as a function of temperature and composition. The free energy of solid solutions has been resolved into many components. Particularly in the case of interstitial solutions, with which we shall be concerned in the present study, however, only the positional entropy component has been intensively studied. The other components are conventionally taken into account by fitting equations for the activity of the interstitial species or the temperature-composition path of phase boundaries, derived principally from positional entropy considerations, to experimental information on these quantities through adjustment of one or more constants in the equations. A number of studies of the thermodynamics of interstitial solid solutions have been made primarily on this basis,'"25 but only Kaufman, Radcliffe, and cohenZ2 (hereafter KRC) and ener''% ave applied the results of such studies to develop relationships for the thermodynamic quantities of interest in the austenite —- proeutectoid ferrite transformation. KRC made use of a model developed by cheil'' (on the basis of a previous study by ohansson'), and subsequently rede-rived correctly by Speiser and retnak,' in which a carbon atom is considered to inhibit occupancy of a certain number of its nearest-neighboring interstitial sites. schei120 determined the number of sites in austenite thus excluded by matching calculated and experimentally measured curves for the variation of carbon activity with the mole fraction of carbon. zener17 used a different approach. He assumed that the positional entropy of carbon is ideal both in austenite and in ferrite (i.e., no excluded interstitial sites), and included all other contributions of carbon in a temperature-independent "free-energy change" accompanying the transfer of 1 mole of carbon between the two phases. This quantity was determined by "pinning" an equation derived for the boundaries of the a + y region to experimental data on the compositions of these boundaries at a single temperature. In the present investigation, three different approaches to the thermodynamics of the proeutectoid ferrite reaction are examined comparatively: I) the method of Zener; 2) the model employed by KRC and predecessors; and 3) the more detailed statistical thermodynamic treatment of the same model developed by acher and Fowler and uenheim, ' in which the problem of overlapping regions of influence of individual interstitial atoms is resolved. In order to make these comparisons, it is necessary to undertake an extension of one aspect of Zener's method; since the Lacher- Fowler -Guggenheim (LFG) treatment has not been previously used in the present context, the necessary thermodynamic "superstructure" for this treatment will be developed in parallel

Jan 1, 1967

By Walter Bradley

MINING by hydraulic process of the important gold-bearing gravels of the Sacramento Valley in the basins of the Yuba, Bear and American rivers began in 1853, and continued at an ever-increasing rate for 30 years. In its most active days it reached an annual production of $15,000,000, and averaged $10,000,000 per year over the 30 years. During that period no provisions were made to prevent the debris from being dis-charged into the water courses, and ultimately large quantities of silt, sand and gravel were washed down to the lower valleys; filling channels, causing overflow of agricultural lands and difficulty in maintaining navigable depths in the Sacramento River. Agitation and suits filed because of these damages finally resulted in the injunction decision of Judge L. B. Sawyer,1 in the U.S. Circuit Court, Jan. 23, 1884, which closed down practically all hydraulic mining operations not having means to restrain their debris. In 1893 (approved March 1, 1893), Congress passed the act introduced by Representative Anthony Caminetti, of California, creating the California Debris Com-mission, composed of three officers assigned from the Engineer Corps of the U.S. Army, and since that time it has been legal and possible within the drainage systems of Sacramento and San Joaquin rivers to conduct hydraulic mining of gold-bearing gravels behind dams built under this commission's permit and supervision. In the watersheds of the Trinity and Klamath rivers, which flow directly to the Pacific Ocean and do not affect navigation or agriculture, operating permits from the California Debris Commission are not required. There is a measure of restriction there, however,. through what is known as the Trinity and Klamath River Fish and Game Dis-trict. Chap. 215, Stat. 1931, in order to secure relatively clear water for the fishing season, provides that between July 15 and October 15 each year there must not be discharged into these rivers debris that will cause a turbidity greater than a content of 50 parts per million in the

Jan 1, 1936

AT A MEETING of the Shareholders of the Russo-Asiatic Cons. Ltd., in London, Oct. 23, 1922, LESLIE URQUHART, chairman of the com- pany made the following statement:* I come now to our recent negotiations with the Soviet Government and to the agreement which has resulted from them. You will remember that the conference at The Hague broke up without having achieved anything very definite. It was not, however, a failure. It elicited from M. Litvinoff an offer which will, I think, come to be regarded as a milestone in the progress of Russia from a ruinous and unpracticable Communism towards a modified form of capitalism. The offer made by M. Litvinoff at The Hague amounted in effect to this: that in return for political recognition on our part the Soviet Government would first acknowl-edge its liability for Russia's national foreign debts, and, secondly, would give the original foreign owners of property in Russia effective compensation. A very great advance that. It showed-and there have been many other signs to confirm it-how real and persistent has been the internal evolution of Russia during the past year from Marxism to the economics of the Western world. I will not now detain you with the reasons why M. Litvinoff's highly promising and significant offer came to nothing. The fact that it had been made and the further fact that The Hague Conference had separated indefinitely were the important things. The first fact seemed to indicate that the Soviet rulers, after all, proved to be people with whom one could do business. The second fact rather emphatically showed that the way to do business with them was not by unwieldy poly-glot conferences of ministers, officials and experts representing a few dozen different governments and a few dozen different sets of national interests. That method had been tried at Genoa. It was tried again at The Hague. Each time it failed, and having failed it left the road clear for a simpler and more direct approach.

Jan 12, 1922

By J. B. Umpleby

PRoduction engineering in 1927 may be characterized by a great. clarification of fundamental conceptions, and many improvements in technique. During the year the profession has received tnarked recogni-tion by the industry and to an extent never before attained has become an integral part of it. History Petroleum production engineering is a new profession. Prior to 1925, when this Institute undertook the work, no forum existed for the open discussion of its technical problems. There was no attempt at a handbook of the subject prior to "Petroleum Production Methods by J. R. Suman, in 1921, and no textbook prior to Petroleum Production Engineering" by L. C. Uren, in 1924. As late as 1926, only six schools and universities offered special courses in petroleum production engineering. Prior to about 1923, engineers engaged by oil companies were used almost exclusively for construction and location work. Two of the leading production engineers in the Mid-Continent field, although with their respective companies more than twelve years, were not definitely assigned to production work until 1924. Both men now head large departments giving almost their entire time to production problems. Because of the newness of the profession, the leading production engineers of today have had their fundamental training in mining, civil, mechanical and electrical courses. Not unlikely this diversified training is in considerable part responsible for the amazing growth of the profession. I believe, however, that recognition is due principally to economic pressure within the industry which has directed attention more and more sharply on costs and efficiency. After all, the justification for the growth and continued development, of the profession is to recover more oil from a given unit of sand at less cost per barrel. In this new profession, it seems to me that greatest progress will result from focusing thought and effort on this single objective, and if I might offer one suggestion to the com-

Jan 1, 1928

By K. Huessener

INTRODUCTION THIS paper attempts a survey of the principles involved in the com¬bustion of blast-furnace gas in boilers and stoves. I do not expect to be able to give much information which is actually new, since the laws and methods of calculation pertaining to this problem are contained in a number of handbooks; but, so far as I am aware, they have nowhere been treated exclusively with reference to this one problem of gas economy. The road which I follow is less that of strictly scientific research than that of the practical engineer, faced by operation problems which require a. quick solution by easily accessible means without a prolonged search in scientific handbooks. For this purpose I give a number of tables and diagrams, as well as the results of many years' practical working experience as combustion engineer, which I trust will prove useful to my readers. HISTORICAL Considering the tremendous efforts made during the last 15 years to increase the efficiency of all kinds of power plants, it is highly surprising that until a comparatively very recent period, progress in the economical combustion of blast-furnace gas has been so slow. The explanation generally put forth, that fuel has been so cheap that it was hardly worth while to bother about this economy, will not hold good, for the greatest trouble was taken to improve the combustion of coal and to reduce the consumption of steam. The most plausible explanation appears to be the general impression, held as an accepted fact, that gas, especially hot, uncleaned, blast-furnace gas, was not a good boiler fuel. Many managers of high repute had tried unsuccessfully to improve the conditions of its use, and the dictum went forth that efficiencies of over 60 per cent., particularly with high loads, were impossible. This was the situation not only in the United States, with very cheap fuel, but also in Europe, where fuel prices are twice and three times as high.

Jan 2, 1916

By A. F. Crawley

The densities of some liquid Pb-Sb alloys up to 11 wt pct Sb and Pb-Sb-& alloys up to 10 pct Sb/10 pct Sh have been determined by a pycnometric technique over a temperature range of about 130°C above their melting points. The data given are accurate within 0.05 pct. Density is shown to vary linearly with temperature , and equations relating these quantities have been formulated. Molar volumes calculated from the density data indicate that volumetric deviations from ideal mixing are undetectable within the limits of experimental error. A continuing research program into some fundamental physical properties of liquid metals is being pursued at the Mines Branch, Department of Energy, Mines and Resources, Ottawa, Canada. This work has received support from the Canadian Zinc and Lead Research Committee in cooperation with the International Lead and Zinc Research Organization. This paper, which reports some density data for Pb-Sb and Pb-Sb-Sn alloys, follows previous work from this laboratory on lead, tin, and Pb-Sn alloys.' Of previous data from others, Greenaway2 and Sato and Munakata3 have reported results on Pb-Sb alloys. No previous work has been published on the ternary Pb-Sb-Sn alloys, reported here. EXPERIMENTAL METHOD Densities were measured by a pycnometric technique which has been described in detail and appraised for accuracy in earlier Mines Branch reports.475 Fig. 1 shows the densitometer with the pycnometer in position for a run. The pycnometer is also shown in some detail. The pycnometer of dense, high-purity graphite, about 14 cu cm in volume, was carefully machined to a uniform, smooth finish. The height was measured by a depth micrometer and the diameter by fitting precision gage blocks between steel balls.' In each case several readings were taken, and the final results were considered accurate within 0.01 pct. The resulting volumetric uncertainty together with small inaccuracies in the coefficients of linear expansion of graphite lead to a maximum systematic uncertainty in the method of ±0.03 pct. As shown in Fig. 1, the pycnometer lid is a threaded cap. Thus, the charge, a cylinder of the alloy, can easily be inserted and the solidified metal can readily be removed after a run. The dimensions of the cylindrical charge are chosen to ensure that, once molten, the metal will not only fill the pycnometer completely but will discharge an excess into the excess-metal float chamber. AS the temperature is increased above the melting point, the volume of metal in the excess chamber increases until the system has equilibrated at the desired temperature. At this point, the excess chamber is moved to one side by twisting the shaft F, leaving a fixed volume of liquid metal in the pycnometer. This volume of fluid is readily calculated using measured coefficients of linear expansion of the graphite which expands anisotropically. The associated weight of fluid is determined as the weight of the solidified metal removed after the furnace has cooled down. Alloys were prepared from 99.997 pct Pb, 99.999 pct Sn, and 99.999 pct Sb, being melted by an electric furnace in a graphite crucible and poured into graphite molds. Several density specimens of the same nominal size were machined from each ingot, and, by comparing specimen weights, relative differences in specimen composition resulting from segregation in the ingots could be detected. In this way, segregation was found to have occurred in Pb-Sb alloys at compositions beyond the eutectic (11.2 pct Sb) and this

Jan 1, 1969

By M. E. Learmont, R. J. Lipp, I. Iwasaki

In the selective flocculation of iron ores, the concentration of alkaline earth ions in pulp solutions plays a critical role. Sodium silicate, alone or with sodium tripolyphosphate, has been used as a dispersant. When Ca+ + concentration exceeds 15 to 20 ppm, however, only a strong complexing agent, such as ethylenediaminetetraacetate (EDTA) was found to be effective (Heerema, Lipp, and Iwasaki, 1979). Some iron ores release Ca+ + in excess of 20 ppm. With ores that contain gypsum, the Ca+ + concentration may reach several hundred ppm. The purpose of this investigation was to compare the effectiveness of EDTA with nitrilotriacetate (NTA) in countering the adverse effects of Ca+ +, particularly at high Ca+ + concentrations. Emphasis was placed on the use of NTA since it is more cost-effective than EDTA. It is also used in detergents in some countries (Malaiyandi, Williams, and O'Grady, 1979). NTA, like EDTA, forms a soluble complex with Ca+ + with a 1:1 molar ratio. Its structure and the value of log Kca are given below together with EDTA (Shibata, 1963). [ ] For experimental materials, an equal weight mixture of Lac Jeannine hematite and a high-purity quartzite from Thompson, MN, both ground to - 30 µm (- 560 mesh) was used. Selective flocculation test conditions and procedures were identical to those used in previous investigations (Heerema, Lipp, and Iwasaki, 1979). The optimum level of starch addition for the above mixture was determined to be at 300 g/t (0.6 lb per st). Initially, a series of selective flocculation tests were performed on the mixture pulped with 10-3M CaC12 (40 ppm Ca + +) at pH 11. With no NTA present, flocculation of the entire suspension resulted. The selectivities achieved in tests with 90, 100, and 150% of the stoichiometric amount of NTA were virtually identical to each other and also to the selectivity of separation obtained in the absence of Ca+ + Such an observation could have been expected since Ca+ + concentrations up to a few ppm may be tolerated in selective flocculation (Krishnan and Iwasaki, 1982). A similar series of tests were performed at 10-2M CaC12 (400 ppm Ca+ +). The results are shown in Fig. 1 as grade¬recovery curves. For comparison, the results obtained in the absence of Ca++ are included. At 90% of the stoichiometric amount of NTA, a large enough concentration of uncomplexed Ca+ + was left in solution to cause indiscriminate flocculation. Note in this figure that NTA is capable of countering the adverse effect of Ca+ + even at this high concentration when it is used in excess of stoichiometric amounts. The free Ca+ + concentrations at 100 and 150% are calculated to be 2.5 and 0 ppm, respectively. [ ] The relative effectiveness of NTA and EDTA was then compared at 100% of the stoichiometric amount using 10-2M and 10-3M CaCI2 (Fig. 2). EDTA appears to be slightly more effective than NTA. The free Ca++ of 0.02 ppm in 10-2M CaC12 with EDTA compared to 2.5 ppm free Ca+ + with NTA might account for the difference. As evident, prohibitively high additions of EDTA and NTA were required to complex high concentrations of calcium ion. The use of both of these agents would result in the accumulation of complexed Ca+ + in recycle water.

Jan 1, 1985

By R. Raring, W. J. Harris, J. A. Rinebolt

The effects of additions of alloying elements on the true-stress, true-strain characteristics of 0.30 pct C, 1.00 pct Mn, 0.30 pct Si pearlitic steel were studied. The alloying elements investigated were C, Mn, Si, P, The alloys are compared on the basis of fracture stress, fracture strain, energy to fracture, rate of strain hardening, strain hardening exponent, height of the flow curve, and lower yield point. IN the past, nearly all studies of the effects of alloying elements on the tensile properties of metals have compared the conventional engineering parameters, namely, tensile strength, yield strength, elongation, and reduction of area. Recently, however, the true-stress, true-strain method of recording results from the tension test has been used; Lacy and Gensamer,' Hollomon," and French and Hibbard- are used this method to study the effects of composition on strength and ductility of metals. In this paper, the effects of certain alloying elements on true-stress, true-strain curves of steels with nearly constant grain size and pearlite spacing are presented. The notation employed in this paper is given in Table I. Since the definitions of stress and strain and the analytical geometry of the stress-strain curve have been explained previously, for example by Gensamer,' they will not be reviewed here. However, the method used for the determination of energy to fracture, E,, requires mention. These energy values were calculated on the assumption that the flow curve followed the idealized equation:' corresponds to the specific energy absorption to that strain value. There is justification for preferring the use of eq 1 for the determination of the energy to a particular strain rather than the area under the experimental stress-strain curve, since Gensamer showed that the use of the Bridgman correctione for stress at the neck of a tensile specimen brought the corrected experimental curve nearer to the idealized power-law curve than to the uncorrected experimental curve. However, it should be noted that the difference between the areas under the idealized curve and the experimental curve is not great for strain of less than 1.0, as can be seen from Fig. 1. In this figure, the true-stress, true-strain curve for a 0.01 pct C, 1.00 pct Mn steel is plotted through the experimental data points. From the value of a,, from this curve and the value of n as determined by the Inm-

Jan 1, 1952

By H. E. Howe, A. A. Smith

The creep properties of lead alloys have been studied by a number of investigators but most of the work has been done on extruded material and the amount of data available on rolled alloys is surprisingly limited. Greenwood1 and his collaborators investigated various rolled commercial leads containing relatively small amounts of impurities, Phillips2 likewise studied rolled commercial leads, although he did include a few alloys— such as tellurium lead and one per cent antimonial lead. But as far as the authors are aware no data on the creep properties of so-called "hard leads"-—i.e., containing from 4 to 8 per cent antimony—have been published. In this paper some data are presented on a few antimonial lead alloys and compared with a copper-bearing lead. Preparation OF Specimens All the alloys used in this investigation were cast at a temperature of 400°C. into an open cast-iron mold preheated to Ioo°C., the resultant casting being % by I by 10 in. The copper-bearing alloy was cold-rolled by 10 per cent passes to a thickness of 0.100 in. Creep specimens 16 in. long were prepared by clamping the strips between wooden blocks and machining the edges of the strips parallel by means of a plane. Careful manipulation gave parallel specimens with no reduced section and with a minimum of distortion. The antimonial lead castings were hot-rolled in 10 per cent passes at a temperature of I50°C. to a thickness of 0.400 in., the heating being carried out in an electric oven after each pass through the rolls. After the castings had been broken down to 0.400 in., they were allowed to cool to room temperature and then cold-rolled to 0.100 in. with the usual Io per cent passes. Sufficient time was allowed after each pass for the strips to cool to room temperature. The apparatus and method of measuring strain have been adequately described in a previous paper3 and essentially the same practice was used in obtaining the present data. Time-extension curves for only two alloys are given, since these are typical of all. Figs. I and 2 show the time-extension Curves for the copper-bearing alloy A at 30°C. and loo°C., and Figs. 3 and 4 show

Jan 1, 1945

By John A. Gann

The following investigation constitutes a brief réumé of the more important binary magnesium alloys from the standpoint of metallo-graphic technique, and the effect of heat treatment on structure and properties. The comparative newness of the subject justifies this procedure as a preface to a more detailed study of each individual series of alloys. The work was started with the idea of practical application in the industry rather than as a theoretical investigation. The alloy compositions studied were selected as those most likely to show whether heat treatment would produce beneficial results. Furthermore, it was considered satisfactory to use commercial 99.9 per cent. magnesium, the best commercial grade of alloying ingredients, and to limit the time of heat treatment at the expense of incomplete equilibrium. These facts must be kept in mind when examining the results obtained, and the conclusions drawn. Preparation of Alloys All melts were made in an oil-fired cast-steel pot, approximately 12 in. dia, by 12 in. deep. Approximately 15 lb. of flux and 50 lb. of magnesium were melted and the calculated amount of alloying metal was added. After thorough alloying and puddling, the metal was chill cast in a graphite mold with four 1/2 by 1/2 by 4 in. bars fed from a common sprue and runner. The next higher composition alloy in a given series was made by adding the calculated amount of metal to the heel from the preceding cast. The pot was thoroughly cleaned after each series and new flux then introduced, thus avoiding possible contamination from earlier melts. The percentage compositions given in Table 1 are the calculated values. While not all alloys were analyzed, enough were checked to indicate that the reported compositions are correct to a few tenths of one per cent. A more detailed description of the foundry methods employed has been given in a previous paper. 1

Jan 1, 1929

By John A. Gann

The following investigation constitutes a brief réumé of the more important binary magnesium alloys from the standpoint of metallo-graphic technique, and the effect of heat treatment on structure and properties. The comparative newness of the subject justifies this procedure as a preface to a more detailed study of each individual series of alloys. The work was started with the idea of practical application in the industry rather than as a theoretical investigation. The alloy compositions studied were selected as those most likely to show whether heat treatment would produce beneficial results. Furthermore, it was considered satisfactory to use commercial 99.9 per cent. magnesium, the best commercial grade of alloying ingredients, and to limit the time of heat treatment at the expense of incomplete equilibrium. These facts must be kept in mind when examining the results obtained, and the conclusions drawn. Preparation of Alloys All melts were made in an oil-fired cast-steel pot, approximately 12 in. dia, by 12 in. deep. Approximately 15 lb. of flux and 50 lb. of magnesium were melted and the calculated amount of alloying metal was added. After thorough alloying and puddling, the metal was chill cast in a graphite mold with four 1/2 by 1/2 by 4 in. bars fed from a common sprue and runner. The next higher composition alloy in a given series was made by adding the calculated amount of metal to the heel from the preceding cast. The pot was thoroughly cleaned after each series and new flux then introduced, thus avoiding possible contamination from earlier melts. The percentage compositions given in Table 1 are the calculated values. While not all alloys were analyzed, enough were checked to indicate that the reported compositions are correct to a few tenths of one per cent. A more detailed description of the foundry methods employed has been given in a previous paper. 1

Jan 1, 1929