Search Documents

By P. M. Robinson, M. B. Beaer

The heat of formation at 0°C of the intermetallic compound AgMg as a function of composition has been determined by tin-solution calorimetry. In this technique, the heat of formation is determined as the difference in the heat effects, at infinite dilution, on dissolution of the compound and a mixture of its components added alternately to liquid tin from a reference temperature, such as 0°C. The experimental technique and method of calculation have been described elsewhere.' The compound AgMg is a 0 electron compound with a CsCl structure.2 In nonstoichiometric compositions of the compound, atoms of the excess component are substituted on the AgMg lattice.3,4 The homogeneity range is approximately 43 to 52 at. pct Mg at room temperature and 38 to 65 at. pct Mg at 500Oc.2 Single-phase alloys outside the homogeneity range at room temperature can be prepared by quenching. The specimens used in this investigation contained from 39.0 to 54.8 at. pct Mg. They were made available, together with analyses, by the Research Laboratory of the General Electric Co. Metallographic examination of the quenched specimens containing 39.0 and 54.8 at. pct Mg gave no indication of the presence of a precipitated phase. The measured heats of formation are listed in Table I. In a calorimetric run, four to six additions each of a specimen and the corresponding mixture of the components were made. One or two calorimetric runs were carried out with each composition depending on the amount of samples available. The limits stated in the table represent the experimental precision and not the absolute accuracy of the measurements. Thermodynamic investigations of the compound AgMg have been made by Trzebiatowski and Terpilowski 5 and Kachi.6,7 The heats of formation at 500°C derived from the combined electromotive-force values of these investigators8 are more exothermic than the heats of formation at 0°C reported here, Fig. 1. The differences cannot be explained by the difference in temperature. This is shown by the published heat capacity of the stoichiometric compound, which obeys the Kopp-Neumann rule from 0" to 500oC.9 The heats of formation derived from equilibrium data are generally considered to be less accurate than those determined by calorimetric methods because small errors in the change of the equilibrium values with temperature have a large effect on the calculated value of the heat of formation. The heats of formation derived from the combined published electromotive-force values reach a maximum at 56.0 at. pct Mg.8 Kachi reports a maximum of -4.7 kcal per g-atom at the stoichiometric composition.7 The present results also indicate a maximum at or near the stoichio metric composition, Fig. 1.

Jan 1, 1964

By J. E. Chappelear

We are concerned with the problem of calculating the forces produced by passing waves on a submerged object (in particular a drilling barge) located on the ocean floor. We employ the linearized theory of waves (the Airy1 theory), since solutions are generally more easily obtained in such a theory. It will be indicated how an approximate solution to the problem can be obtained for waves of finite height by use of a linear combination of Airy waves. We shall assume the submerged object has an infinite length, thus neglecting diffraction and making the problem two-dimensional. We find that there is not a considerable difference between our solution and the usual engineering solution. The force, as a function of time, is plotted in Figs. 4 and 5, together with the usual solution for easy comparison. So far, no experiments have been found to compare with the results. As will be shown, the calculations can be extended to waves of finite height (Stokes2-Struik3 waves) in an approximate fashion. This can be done by calculating the force produced by each Fourier component of the wave, separately, and omitting the coupling between the various harmonics produced by Bernoulli's theorem. The problem and its boundary conditions will be briefly stated. We seek a function, +, the velocity potential, which is harmonic, ?2?=0...........(1) and which satisfies the boundary conditions ??/?n =0 .......(2) (the normal derivative of + is zero) on the ocean floor and the sides of the barge, and s??/?y = ?..........(3) on the ocean surface, where s = g/w2........(4) The physical reasons for these choices and an interpretation of ? are given by Lamb.' As previously stated, we assume also that the problem is two-dimensional. We set up our coordinates such that x = 0 is the center of the barge and y = 0 is the ocean floor. The coordinates are shown in Fig. 1, together with the location of the barge on the bottom. Our solution may be decomposed into a function which is symmetric about x = 0,?e, and one which is antisymmetric, +,, ? = ? + ?o...........(5) Thus directly above the barge we have as boundary conditions that for x = 0, ?o = 0, ...........(6) and ??e/?x = 0........(7) Now, far from the barge, we have that (for x positive and assuming the waves are incident from the left) ?e ? Ae cosh ky cos k (x + a) , . . . (8) and ?e ? Ao cosh ky cos k (x + ß) . . . . (9) where + means ". .. approaches ... for x large." Let us put Ae, Ao, and k equal to one, and remember that, in accordance with the derivation of Eq. 3, a sinusoidal time factor is to be supplied. Then we may rewrite Eq. 8 for ?e, and we find that

Jan 1, 1958

By Ottar Dragge, C. Danielsson, Bo Kalling

THE desulphurizing of pig iron has been accomplished with a number of different additions. The oldest and still most commonly used agent is soda, the extensive use of which commenced about 1925, when it was used principally for cupola furnace iron. More recent experience' seems to show that better results can be obtained with sodium hydroxide. The well-known desulphurizing properties of lime have also been exploited in different technical processes. Another material with even more powerful effect is calcium carbide.' The desulphurizing ability of manganese, when added to the ladle in sufficient quantity, should also be mentioned in this connection. During recent years increasing attention has been paid to the desulphurizing properties of metallic magnesium." An addition of a suitable alloy of magnesium is now in use purely for the purpose of sulphur elimination. Of the desulphurizing agents mentioned, lime is by far the cheapest, provided that the reaction can be brought about rapidly and completely. Therefore, a method that makes full use of the desulphurizing ability of lime may be able to compete with other processes. A method developed at the Dom-narfvet Iron and Steel Works (Sweden) will be described, which enables pig iron to be rapidly desulphurized to very low sulphur contents by using a burnt lime powder. as the desulphurizing agent. Lime in Older Processes In cases where lime has been used for the desul-phurization of pig iron, it has generally not been used alone, but mixed with other substances such as fluorspar, to obtain the formation of a molten slag during the process. This method has been tried by Tigerschiold,' who treated the iron with a lime-fluorspar mixture, the stirring of the iron being brought about inductively with low frequency alternating current. Very good results were obtained. A process of this type has also been suggested by R. P. Heuer, U. S. A. The principles of this method, which has been tested in Great Britain by Newell. Lanener. and Parsons." re that a mixture of lime and fluoispar is added to the hot metal in the ladle, while a powerful stream of nitrogen gas is blown into the bath to produce the required intermixing. The results of the tests were unsatisfactory, however. A similar process has been developed at The Steel Co. of Canada, according to a statement by H. M. Griffith.' Here the tests were carried out in a carbon-lined ladle provided with carbon tuyeres in the side wall for blowing nitrogen into the bath. The addition consisted of about 20 lb of a mixture of burnt lime and fluorspar per ton of pig iron. Good results appear to have been achieved. The sulphur content of the pig iron is stated to have been reduced from 0.025 to 0.050 pct down to 0.006 pct. Various methods of desulphurizing pig iron have been tried using lime powder without fluxing material for fusing. Eichholz and Behrendt7 have experimented with blowing a powdered limeicoke mixture with air into the ladle. Their results were, however, not conclusive and the experiments do not appear to have been continued. Similar experiments have been carried out at Domnarfvet, using nitrogen instead of air in order to avoid oxidation. But these attempts were not particularly successful. It appears to be difficult to achieve the required agitation by this means. The strong cooling effect of the gas on the iron is also a serious drawback. A method in many respects similar to that tried at Domnarfvet was tried by Eulenberg and Krus at the end of the 1930's. Here again desulphurization was carried out with lime alone, brought into contact with the molten iron in a rotary furnace. The temperature was kept at the required level, 1400" to 1500°C, by the introduction of a pulverized coal burner in one end of the furnace. The speed of rotating was not given. A paper by Bading and Krus states that, in one of the first experiments, the sulphur content in 56 tons of pig iron was brought down from 0.186 to 0.035 pct in 117 min, but that a considerable shortening of the time would be possible. According to later reports by Eichholz and Behrendt,' it should be possible by this process to achieve a desulphurization speed of 0.35 pct S per hr for a consumption of 6 to 10 pct limestone and 2 to 3 pct coke, as fuel exclusively. The final sulphur content is, however, not stated. Domnarfvet Method After a number of different procedures had been investigated, the tests at Domnarfvet were directed to desulphurization with lime in a rotary furnace. Before going into the practical details of the method, the theoretical aspects will be discussed briefly. If the pig iron does not contain alloying elements other than carbon, the reaction can be expressed most simply by the usual equation: FeS + CaO + C = Fe + CaS + CO [I] 4H,. ~ 34,000 cal That this reaction can be carried through to a very complete desulphurization of pig iron has been shown by OelsenD in a discussion in connection with the Eulenberg and Krus' method. He mentions two laboratory tests, in one of which the sulphur content in the pig iron at 1400°C was reduced from 0.540 to 0.006 pct after treating with 3.35 pct lime. The pig iron had a low manganese content, but other analysis is th. given. Mention also should be made of the recently published investigations by Fischer and Cohnen'" dealing with the influence of the carbon content of the iron on desulphurization with lime, although in this case fluorspar was added also. The tests show that efficient desulphurization is possible with lime in the steel bath, provided that the carbon content is sufficiently high. The temperature employed in these tests was considerably higher (1620") than that normal for treatment of pig iron. The author concludes that the product S% X C% - 0.011 at the temperature in question.

Jan 1, 1952

"No true conception of the Park City mining district can be obtained without first giving consideration to the part it has played as a consistent producer of mineral wealth. Its position in this regard is almost unique in the annals of a lead silver camp. For over fifty years it has been a continuous producer of lead and silver and for twenty years it has added to the world's supply of zinc. Few camps with its productive history are so little known to the mining fraternity for the reason that its life has never been punctuated by periods of ""boom"" which serve to attract general attention, neither has it been the field of operation for promoters who temporarily focus attention upon their scene of action. Its history is one of legitimate mining operations. These were at first carried on by a number of smaller companies. A period of consolidation followed and at the present time the entire production of the camp is in the hands of two major companies and one smaller company. These are flanked by a number of prospecting properties, which are at this time actively engaged in the search for ores and later events will doubtless put some of them in the producing class.A technical discussion of the ore occurrence and mining operations in the camp will be the subject of a paper to be read before this meeting of the Institute. The mission of this article is to supply a ""Baedeker"" where Baedeker is lacking.The town of Park City is a typical, up-to-date, western mining camp which owes its existence as a town of 4,500 inhabitants solely to the mining industry. The camp is located 7,000 feet above sea level, thirty-two miles east of Salt Lake City. It is situated on the Victory Highway seven miles from its junction with the Lincoln Highway and has the benefit of excellent automobile communication with the metropolis of the state. Both the Denver and Rio Grande and the Union Pacific Railroads give daily train service to the camp and effectively solve the transportation problems of the mining companies."

Jan 1, 1925

By J. E. Hanafee, G. J. London

MANY studies of the deformation behavior of materials under a superimposed hydrostatic pressure have shown that materials brittle at ambient pressure behave in a ductile manner under pressure. Thus, with a metal such as beryllium which possesses relatively low ductility, but otherwise exhibits quite useful physical and mechanical properties, hydrostatic pressure may be particularly useful for both forming beryllium shapes and studying its deformation behavior. In fact, it has been found1"4 that polycrystal-line beryllium in both ingot and powder form appears to behave in a more ductile manner on a macroscopic level in a hydrostatic pressure environment, and it has been suggested2 that this is due to activating a new slip mode. Furthermore, Andrews and Radcliffe5 have found pressure induced nonbasal dislocation activity in hot pressed beryllium. Recently6 it has been shown in "c-axis" compression tests under hydro-static pressures up to 28 kbars that the shear stress needed to cause slip with a Burgers vector out of the basal plane (pyramidal slip) does not change with increasing pressure in beryllium with a purity of some 99.5 pct. This material is equivalent or more pure than the beryllium used in the previous pressure studies. Thus, it appears, as suggested by Inoue et al.,3 that the hydrostatic pressure affects the fracture stress rather than the stress necessary to activate pyramidal slip in beryllium. However, in "c-axis" pressure tests on high purity 12 zone pass beryllium (˜50 ppm total impurities) the macroscopic compression stress needed to cause pyramidal slip was considerably lower than that at ambient pressure.6 It has further been shown that alloying beryllium with nickel and copper in the range 2-5 wt pct also favors the occurrence of pyramidal slip in "c-axis" compression tests,7'8 while lower amounts of nickel and copper do not have significant effects. In the present study the combined effect of hydrostatic pressure and alloying high purity beryllium on the shear stress needed to cause pyramidal slip has been ascertained. A 2.5 wt pct Cu alloy was selected as the first alloy to study as this level of copper did favor pyramidal slip at room pressure. A high purity (12 zone pass) single crystal of beryllium 0.3 by 0.1 by 0.1 in. was cut and polished by an orientation and lapping technique8 so that the top and bottom compression surfaces were parallel and within 3 min of arc to the (0001) plane and the sides parallel to the {l010} and {ll20} planes. In these compression specimens, therefore, the resolved shear stress was nearly zero on both the basal and prism planes, and slip was restricted to pyramidal systems. Analysis of slip traces on the two lateral surfaces served to accurately identify the active slip planes.6'9 The pressure unit was a modified piston-cylinder device fitted with a manganin transducer coil arrangement which continuously monitored and recorded the hydro-static pressure. The load on the specimen was measured by a strain gage load cell which operated entirely within the pressure chamber. This load cell was calibrated before and after each pressure cycle at room pressure in situ and the calibration did not vary more than ±1 pet. These techniques and devices have been previously described in more detail.6 Successively higher compressive stresses were applied to the single crystal under a superimposed hydrostatic pressure until fracture occurred. The strain rate was (4.5 ± 2.0) x 10-6 sec-1 and the average rate of pressure application and release was approximately 0.3 kbars per min. As the load on the specimen was applied by the piston which was used to increase the hydrostatic pressure, the pressure increased during the compression test. This increase ranged from 0.0 to 0.8 kbars, and the maximum hydrostatic pressures are quoted in Fig. 1. The lateral surfaces of the specimen were examined in a light microscope after each pressurization/stress cycle so that the stress at the onset of {1122} pyramidal slip could be ascertained. Post compression height measurements allowed the plastic strain in the specimen to be evaluated to within 0.03 pct. The resulting compression stress-plastic strain curve is shown in Fig. 1 with results of a "c-axis" test on a similar Be-2.5 wt pct Cu single

Jan 1, 1970

By L. M. Pidgeon, K. T. Aust

There has been considerable interest in the possible use of titanium in magnesium alloys.' Zirconium has shown some promise in this connection2 and its general similarity with titanium suggests that the latter might act in a similar manner. A literature survey revealed that quantitative data on the Mg-Ti system was unavailable. Several patents3 have claimed that titanium additions from 0.2 to 4 pct to magnesium alloys were possible, but no mention was made as to the form in which the titanium existed in the alloy. Kro114 succeeded in introducing only traces of titanium into magnesium by bubbling TiCl4 through the metal under argon or by reacting it with sodium titanium fluoride. The application of theoretical data given by Carapella5 based on Hume-Rothery's principles, involving atomic size factor, crystal structure, valency and the electro-chemical factor, suggests that a Mg-Ti alloy is a favorable case, and the system appeared to warrant experimental examination. Experimental Procedure and Results THERMAL ANALYSIS If titanium is appreciably soluble in magnesium, a change in the melting point of the magnesium might be detectable using standard cooling curve methods. Magnesium was melted in graphite crucibles under an argon atmosphere, the assembly being enclosed in a silica tube. Graphite thermocouple protection tubes served also to stir the melts. The apparatus was very similar to Fig 1, with the addition of a refractory and baffle system to prevent undue heat losses from the top of the crucible. Chromel-alumel thermocouples were calibrated using Al of 99.97 pct purity. Dominion Magnesium Limited sup- plied redistilled high purity magnesium of the analysis given above. Titanium was added in three different forms: 1. Titanium powder —100 mesh, from the Titanium Alloy Manufacturing Co., Niagara Falls, N. Y. 2. Sheet titanium from the U.S. Bureau of Mines, produced by Mg reduction of TiCl4. 3. Magnesium —50 pct titanium master alloy from Metal Hydrides Inc., Beverly, Mass. The melting point of the high purity magnesium used was measured experimentally as 651.0°C. More than a dozen tests were conducted using titanium from the three sources referred to above, in calculated additions up to 20 pct titanium, at temperatures between the melting point and 1000°C and holding periods up to 6 hr. In no case was evidence obtained of solubility of titanium in magnesium, using inverse-rate and time-temperature curves. The melting point of the magnesium was unchanged within the accuracy of measurement, namely -+0.5°C; and no other thermal arrests were detected. Metallographic investigation of the thermal analysis billets indicated that the titanium additions were apparently mechanically entrapped in the magnesium in segregated areas. Consequently, these samples were not analyzed for titanium. The master alloy proved to be a mechanical mixture of titanium particles in a magne- sium matrix. These results indicated that the titanium solubility, if such existed, could not be obtained by the usual thermal methods. X RAY DIFFRACTION INVESTIGATION In an effort to detect solubility of titanium in magnesium, samples were investigated using both the Debye-Scherrer and the Focusing Back-Reflection methods. Filings from samples of the thermal analysis billets and from pure magnesium were annealed in argon one hour at 350°C to relieve mechanical strain. Measurements made of the interplanar spacings showed no difference between the Mg-Ti samples and pure magnesium. The interplanar spacings could be measured to within 0.0002A, and the greatest variation found was 0.0004A, in the back-reflection method. The diffraction lines for magnesium were not shifted by the titanium additions indicating that the solid solubility of titanium in magnesium is of a very low order—less than 0.5 pct. From both diffraction methods, a d or interplanar spacing of 0.817A was obtained for the redistilled high purity magnesium. This latter value is not given in the standard X ray diffraction cards for magnesium metal or vacuum distilled magnesium. Theoretical calculations for a close-packed hexagonal space lattice for magnesium indicate that the planes {2134) should give a line which was found. The relative intensity for this reflection at 0.817A is slightly less than that at 0.870k for magnesium. SOLUBILITY OF TITANIUM IN LIQUID MAGNESIUM The Mg-Mn system was examined by Grogan and Haughton6 who were

Jan 1, 1950

By C. L. Sainsbury

Lode and placer tin deposits of the western Seward Peninsula, Alaska, have produced more than 2200 tons of metallic tin and constitute the only known domestic deposits of economic grade and size. The lode deposits consist of quartz-topaz greisens containing cassiterite and wolframite as well as numerous base-metal sulfide minerals, and most are in or near altered biotite-granite that forms isolated stocks or in rhyolitic dikes near granite. Within the main lode-producing area in the central York Mountains, nonpegmatite beryllium deposits, consisting principally of fluorite, chrysoberyl, diaspore, tourmaline, and white mica, with minor euclase, bertrandite, phenakite, hematite, and todorokite, are distributed zonally around the tin deposits and locally are transitional with them. All the known beryllium deposits are replacement lodes in carbonate rocks. In the area discussed, both tin and beryllium deposits are localized in a structural belt striking N70° to N85°E across the central York Mountains. The belt is characterized by numerous normal faults, which cut extensive thrust sheets, and by dikes of rhyolite, rhyolite porphyry, and lamprophyre that were injected along the faults. Ore deposits are localized where the dikes intrude brecciated rocks beneath thrusts and, although complex in detail, form tabular lodes that tend to lie along the thrusts. The granites contain abnormal amounts of tin, beryllium, lithium, and boron, and the tin and beryllium lodes are believed to be genetically associated with these enriched granites

Jan 1, 1968

By S. F. Reiter, W. R. Hibbard

A survey of the effect of heat treatment on the room temperature hardness of Fe-Mo alloys has been made. Constant strain rate tensile tests were performed between room temperature and 1800°F. These data were analyzed to determine the effect of temperature and composition on the strain hardening coefficient and strain rate sensitivity. Constant load creep-rupture tests were made on these alloys and the results related to composition and structure. A relation between the high temperature strength of the precipitation hardened alloys and the volume of precipitate has been observed. IN view of the extensive use of ferritic materials at elevated temperatures, it is surprising to note the limited amount of information relating the variables of plastic deformation, i.e., composition, structure, temperature, stress, strain, and strain rate. Hollomon and Lubahn' showed how the several variables of plastic flow might be treated analytically. No data were available on carbon-free iron and its alloys in a form suitable for this analysis. Several German investigations2-" constitute most of the experimental work relating high temperature properties to the constitution of these types of materials. In order to obtain new data, the iron-rich alloys of the Fe-Mo system were selected for detailed investigation for the following reasons: 1—Some of the important effects of molybdenum on the mechanical properties of iron have already been studied.' , 821 2—By suitable heat treatment of selected alloys, it is possible to study strengthening effects of four types: AT -a transformation, B—substitutional, C—precipitation, and D—dispersion of hard inter-metallic compound. Materials and Treatment Four-pound ingots were vacuum cast, employing the same melting schedule previously used.? The raw materials were electrolytic iron and lamp-grade molybdenum. The ingots were forged to l/z in. sq. rod and one portion swaged to 0.350 in. diam rod for the production of 1 15/16 in. long button-head specimens. The button-head specimen blanks were solution treated for 16 hr at 2100°F in hydrogen of —70°C dewpoint and then water quenched. They were subsequently plunge ground to the standard 0.160 in. diam test bar. Micrographs of the solution treated alloys are given in Figs. la through Id. The higher molybdenum alloys contained large equiaxed ferrite crystals similar to those in Fig. Id. A portion of the % in. rod was hot rolled to 0.100 in., sandblasted, and cold rolled to 0.020 in. Strip tensile specimens having a 0.020x0.200 in. cross-section and a 2.25 in. gage length were machined from the sheet. The alloys containing molybdenum were subsequently annealed 1 hr at 1560°F. The iron strip was annealed 4 hr at 1300°F in wet hydrogen. The resultant structures are shown in Fig. 2a through h. The ASTM grain sizes were 1 to 3 as solution heat treated or 3 to 4 as annealed. The chemical analyses of the alloys are given in Table I. Carbon contents were obtained after the heat treatments in hydrogen. Alloy 15.9 pct Mo was tested as a cast alloy.'

Jan 1, 1956

By Nicholas J. Grant, Bill C. Giessen

The phase diagram Ta-Ni has been treated repeatedly; investigations up to 1958 are summed up in Ref. 1. Since then, an equilibrium diagram has been presented by Kornilov and Pylaeva.2 They found the following intermediate phases: Ta2N; (CuA12 type),3 "TaNi" (p phase, Mo8Co7 type), TaNiz, and TaNi3 (Ticus type).5 Of these, the crystal structure of TaNin remained unknown, and no further literature reference was found. According to Kornilov and pylaeva,&apos; TaNil melts peri-tectically at 1420°C. A 5-g alloy of Ta + 66.7 at. pct Ni was prepared by inert-gas arc melting using 99.95 pct Ta rod (NRC-MG) and 99.9 pct Ni shot (Fisher). The weight loss after three melts was <2 mg; a microscopically homogeneous ingot resulted. As shown in Ref. 6, no oxygen or impurity pickup needed to be considered under these conditions. Specimens were annealed for 15 hr at 1350°C, 15 hr at 1205oC, and 15 hr at 875°C with subsequent powdering and stress relief for 10 min at 1350°C, 15 min at 1205oC, and 1 hr at 875oC, respectively. Micrographs and X-ray analysis (114.6 mm Norelco camera, filtered CuK, radiation) showed homogeneous one-phase alloys in the as-cast state and at all three temperatures, all having the same powder pattern except for broad lines in the as-cast state. From this it is concluded that either TaNi, melts congruently or its melting behavior is a transition between the eutectic and peritectic cases. Since it was found that very slight surface contamination on stress relieving can considerably alter the structure of similar phases (e.g.,TaPt3),7 patterns before and after stress relief were also compared; they were identical except for line broadening in the non-stressrelieved condition, and two faint impurity lines in the stress-relieved samples. The powder pattern is presented in Table I. All lines were accounted for by indexing with a tetragonal lattice, 0Yh- I4/mmm , with a, = 3.154 ± 0.001A, co = 7.905 * 0.002i and c/a = 2.506. The atomic positions are: 1000; 1/2, 1/2, 1/2] + 2Ta(a): 000; + 4Ni(e): *(002); z = 0.333 * 0.002 This proves TaNi2 to be a representative of the MoSiz (Cllb) type. The variable parameter was determined by grouping the visually estimated intensi- ties according to their 2 indices, plotting their F values, and varying z for best fit, which was obtained at z = 0.333= 1/3. Since absorption was not considered, only the relative intensities with similar 28 can be expected to agree. The interatomic distances are presented in Table 11; the standard error is *o.o2A, resulting chiefly from the uncertainty in z. These distances indicate a coordination number 10 for both kinds of atoms and show that the pseudohexagonal layers along (110) are rather un-distorted. The mean atomic volume of 13.1A3 is close to the Vegard&apos;s law value of 13.3A3, showing

Jan 1, 1964

By K. H. Adams, T. Vreeland

The basal stress-strain behavior, dislocation density, and strain vale sensitivity of the flow stress uqere measured at room temperature on single crystals oj-zone-refined zinc , 99.999 pct Zn, and zinc containing 0.0025 and 0.02 wt pct Al. No significant change in the stvain rate sensitivity of the flow stress occurs with the addition of aluminum. Changes in dislocation substructure and nonbasal dislocation density were obserrled with the addition of aluminum. The effect of aluminum on the basal slress-strain behavior is explained in terms of changes in nonbasal dislocation density which determines the separation distance of junctions between basal and nonbasal dislocations. The onset of basal slip is associated with the breaking of attractive junctions. The chunge in basal dislocation density was found to be proportional to the one-third power of the plastic shear strain, indepedent of purity. THE effect of impurities in solid solution on the stress-strain behavior of single crystals has been the subject of many theoretical studies. These studies have generally concentrated on the interactions between impurities and dislocations to explain the hardening effeet of impurity additions. The theories that have been proposed include those of yott and Nabarro,&apos;l&apos; Cott-re11; Suzuki; and Fisher. In practice, it is generally difficult to predict the relative importance of the vari- ous effects due to impurities. In addition, secondary effects of impurity additions such as induced changes in dislocation density and substructure in the as-grown crystals have received little attention. Many experimental investigations have been conducted on the effect of impurities on the stress-strain behavior of fcc crystals. Hcp crystals have not received much attention except for the extensive work of Levine et a1.= on magnesium alloy crystals. Stuwe~&apos;&apos; has studied the effect of copper impurity on the critical shear stress of zinc crystals and has interpreted the results in terms of the impurity atmosphere model of Cottrell and Jaswon. This report presents the results of an experimental study of the effect of aluminum additions to zinc on the basal stress-strain curve and the strain rate sensitivity of the flow stress. Etch pit techniques were used to measure and characterize the dislocation density and substructure in the zinc alloy crystals. EXPERIMENTAL PROCEDURE Specimen Preparation. Compression test specimens of four different purities of zinc were prepared from CP grade zinc of 99.999 pct purity obtained from the New Jersey Zinc Co. An analysis of this material furnished by the supplier indicated the following impurities in wt ~ct: Pb = 0.0002; Fe = 0.0002; Cd = 0.00005; other <0.60011. A quantity of material of this grade was further purified by zone refining. Zone refining was carried out under a helium atmosphere by passing a double &apos;One furnace Over a 6-ft-10ng charge at the rate of 2 in. Per hr. * total of ten double zone passes were made before the charge was removed from the furnace. The first one third of each charge was used to grow single crystals. Quantities of two

Jan 1, 1969

SUCCESSFUL development of a new process for heat hardening of pellets made from taconite concentrates was announced by Arthur G. McKee & CO., steel plant engineering and construction firm of Cleveland, and Allis-Chalmers Mfg. Co. An order for the design, engineering, and materials for a plant incorporating the process, has been received by the McKee Co. from the Reserve Mining Co. for its new E. W. Davis Works at Silver Bay, Minn. It is estimated that this plant will cost around $19 million and when in full operation, will turn out 12,000 tons of pellets per day.

Jan 10, 1954

By M. R. Campbell

Coal is the geological product of entombed vegetal tissues. This view of its origin led Stopes and Wheeler to define it as "mummified plants." They evidently intended this term to be used in a broad way and to mean the preservation of the organic material, as such, regardless of the means employed to accomplish the purpose. The term " coal" should be regarded, therrfore, as broadly generic, and applicable to all accumulations of vegetal tissues as soon as they are covered and protected either by water or by earthy material. In this sense peat should be regarded as the first stage of coal formation and the term coal should include the resultant products of transformation in all other stages of the process until they have lost all resemblance to the original matter from which they were derived. If this idea of the development of coal is accepted and it is admitted, as the geologists claim, that the forces which produced this transformation of the coal have been active since vegetation began to grow upon the land, and are still in operation, it is obvious that somewhere in the world there are all gradations of this material from peat just forming in the swamps of today to graphitic anthracite which presumably marks the most advanced stage that can be recognized with certainty as belonging to the series. Some of these coals, particularly those occurring in the upper part of the series, are fairly well known because they are the ones that are most widely distributed and have been mined and utilized most extensively. On the other hand, the coals in the lower part of the series are but little known because they are not so abundant and, owing to their relative inefficiency, have been only slightly exploited and utilized, especially in regions where the better coals are abundant. The result of these conditions is that much research work has been done on coals of the higher ranks and a great body of facts regarding their physical and chemical properties and the uses to which they are best adapted has been accumulated, but little information is available regarding the coals of the lower ranks. Many able scientists, particularly chemists, have attempted to bring some order of the chaos of coals of various compositions and uses by

Jan 1, 1930

By R. A. Anderson, T. E. Tietz, J. E. Dorn

Recent investigations1,2,3,4 have conclusively shown that the strain hardened state of metals depends upon the temperature and strain rate of pre-straining as well as on the total plastic strain. A typical example of the effect of temperature of prestraining on the work hardening of metals is reproduced in Fig 1. When pure aluminum is strained at liquid nitrogen temperature the upper solid stress-strain curve (OFGH) is obtained. But when pure aluminum is prestrained to e2 = 0.153 at atmospheric temperature and the test is then completed at liquid nitrogen temperature, the curve OBCD results. Thus a prestrain E2 = 0.153 at atmospheric temperature gives a flow stress C when continued at liquid nitrogen temperature, whereas a higher flow stress G results when the specimen is strained exclusively at liquid nitrogen temperature to the same strain E2. Consequently the metal strain hardens more rapidly at the lower temperature. Obviously the strain alone is not a measure of the strain hardened state in metals. Inspection of Fig 1 reveals that the flow stress at C is identical with that at F. This fact suggests that a strain E2 = 0.153 at atmospheric temperature induces the same work hardened state as a strain E1 = 0.058 at liquid nitrogen temperature. But this concept of equivalent strains is also in error. If curve CD is shifted to the left so that point C falls on F, point D becomes D&apos;. Inspection of the curves reveals that the rate of increase of stress with strain at C is greater than the rate of increase of stress with strain at F even though the flow stresses are identical. Consequently C and F do not represent identical work hardened states. It therefore becomes important to ascer- tain how the strain hardened states at C and F might differ from each other. In a more recent report1 it was shown that straining at higher rates of strain increases the amount of strain hardening in a manner quite analogous to straining at lower temperatures. These observations suggested that the flow stress is not only a function of the strain but also a function of the strain rate-temperature history of straining, perhaps in accord with the Zener- ?H Hollomon parameter p = Ee /RT (where

Jan 1, 1950

By John Richards

MY remarks will be confined to the experience of our company in mining the No. 8 seam of coal in Ohio, although I believe that the relationship existing here between the method of mining and the method of cleaning will hold true in many of the coal seams throughout the country. The increasing demand for a cleaner and better graded product is being felt throughout the entire coal industry, and the methods of mining are playing an important part in the control of various sizes and quality of coal produced. We have found a definite relation between the mechanical loading of coal and its preparation for the market. In the No. 8 coal seam the location of the non-combustible material is regular. The&apos; marketable coal lies in three benches, separated by streaks or bands of impurities. These impurities must be removed from the coal to properly pre pare the product for the market. Where hand-loading methods are employed, the loader removes as much of this non-combustible material as possible at the working face. The impurities that are missed by the loaders are removed as the coal passes through the preparation plant, by means of picking tables. As this method of cleaning cannot improve the quality of the extremely fine sizes, a practice has been established in the company&apos;s hand-loading mines, of undercutting the coal about 2 in. above the bottom of the seam, thereby eliminating any possibility of impurities caused by the cutting machines cutting into the rock bottom below the coal seam.

Jan 1, 1934

By Richard McCaffery

WHEN we began the study of blast furnace slags we limited our work at first to a study of those slags containing only lime, alumina and silica. On our paper1 on some of the results of this first work, the solubility of sulfur in slags containing no magnesia was reported and the question of sulfur solubility and slag viscosity discussed. There has been, for a long time, a very great difference of opinion among metallurgists as to he effect of magnesia in blast furnace slags, and the literature is full if expressions of the most contrary opinions on the subject. As a result, our next publication&apos; developed the constitution of slags considered as a four-component system, silica-alumina-lime-magnesia, and advanced an explanation of slag structure which accorded with the facts and with scientific theory. The present paper continues our study of the general subject of slags. As blast furnace slags are included in the silica-alumina-lime-magnesia system, which is a particular case of four-component solutions, we have determined that there are 22 components Table 1), which may enter into the silica-alumina-lime-magnesia system and that 10 or 12 of these components may be present in blast furnace slags which are within the ordinary ranges of composition. To cave a very definite conception of the behavior of these components in a slag, we have developed the theory of the cooling of a four-component solution from the liquid state to the solid and the conclusions that we obtained have been made use of in this paper. On account of the importance of the four oxides and 18 compounds which enter into the silica-alumina-lime-magnesia system, some method of calculating the percentages of the various compounds that are present in the slag when the percentages of the oxides are given, seemed very desirable and we develop L method later herein for doing this, and finally we give illustrations of the composition of a wide series of blast furnace slags and show some applications of these composition data.

Jan 1, 1927

By T. M. Morris

G. L. Simard and D. J. Salley—The authors and ourselves" independently came to similar conclusions both as to the value of tracer methods for the study of flotation and the general nature of collector-mineral interaction. The dodecylamine-quartz system appears to be simpler than the dithiophosphate-galena one, and the results therefore appear clearer. It is evident from a comparison of the two papers, however, that care must be used in extending the results to other more complicated systems. In the case of dodecylamine-quartz, the possible influence of micelle formation is of interest. There is no a priori reason why complete monolayer formation should necessarily occur at the concentration for micelle formation, since sorption depends on the nature of the substrate as well as on the properties of the solute in solution which alone determine micelle formation. Indeed, the fact that the onset of increased adsorption, point B in fig. 2, occurs at a concentration one tenth the critical value for micelles might imply that micelle formation does not have an influence. Interestingly enough, the data may be handled by the methods used for multilayer adsorption of gases on surfaces. Thus, if the amount adsorbed is plotted versus concentration, a sigmoid type curve is obtained, similar in form to a so-called Type I1 isotherm13 generally attributed to multimolecular adsorption. A monolayer value of about 0.12 mg per g may be estimated from the knee of this isotherm. On the other hand, if a plot is made according to the multilayer gas equation for adsorption to an unrestricted number of layers, eq 38,13 assuming the critical micelle concentration as the saturation concentration, the data above 120 mg per liter fall on a straight line from which a monolayer adsorption of 0.3 mg per g results. These considerations suggest that the monolayer may occupy an area somewhat less than the geometric value of 0.4 mg per g, and that micelle formation may indeed be a factor in the adsorption. the angle between the solid-liquid and liquid-gas interfaces, measured through the liquid. The value of the equilibrium contact-angle is uniquely determined by the value of the interfacial energies of the three intersecting interfaces and is independent of other forces in the system. When the liquid-gas interface intersects the solid at an edge—as was the case for all the experiments reported in this paper—the orientation of the solid-liquid interface is indeterminate or varies through 90" for a right-angle edge. Mr. Morris has called the angle between the horizontal and the liquid-gas interface for this edge condition a "static contact-angle." I feel that this term is unnecessarily misleading. In the first place, "static contact-angle" sounds too much like "equilibrium contact-angle." In the second place, the magnitude of the "static contact-angle," which I would prefer to call the "supporting angle," is determined by the forces in the system other than those derived from the interfacial energies, hence "contact angle" is misleading. If Mr. Morris had said that the "supporting-angle" is variable and depends on the weight of the particle and size of the bubble and that it has a maximum possible value equal to the equilibrium contact-angle, his discussion would have been more accurate. T. M. Morris (author&apos;s reply)—Mr. Kellogg puts forth a reasonable criticism of some of the terminology used in the paper. I agree that the term "static contact angle" may be misleading. Substitution of the term "supporting angle" or "vector angle" may be more suitable. F. X. Tartaron—In this paper the author presents a very interesting mathematical development of the forces present when a mineral particle adheres to an air bubble. Excellent concordance is obtained between mathematical formulation and experimental results. It is the writer&apos;s understanding that when the mineral surface presented to an air bubble is greater than the area of contact, the maximum contact angle is obtained. However, this contact angle represents distortion of the bubble, the normal shape of which is spherical or in cross-section, circular. This distortion produces a force that acts in opposition to the force of adhesion between the bubble and particle. Hence, at maximum contact angle, the force of adhesion between bubble and particle is at a minimum for static conditions. However, when the size of bubble is increased, the size of particle remaining the same (and all other conditions remaining the same), the contact angle decreases, the distortion of the bubble decreases and the force in opposition to adherence of bubble and particle also decreases. Thus, there is stronger attachment between bubble and particle. When this situation is applied to actual flotation conditions, it is doubtful that it has any significance. The reason is that the bubbles are normally so much larger than the particles, that in substantially all cases, it is probable that negligible distortion of the bubble takes place. In table IV, the author makes computations for bubbles from 0.50 to 2 mm diam. This is from 0.02 in. to 0.08 in. Certainly the bubbles generated in a flotation machine are far larger than this. The surfaces of the author&apos;s bubbles range from 0.79 to 12.6 sq mm. The area of contact of the glass rod (0.15 mm diam) is 0.017 sq mm. Thus, ratio of bubble surface to mineral area of contact ranges from 47 to 741 in round numbers. If we take a %-in. diam bubble and a 65-mesh (0.208 mm) particle of cubical shape, the ratio of bubble surface to mineral area of contact is 2931. Mineral particles do not readily become attached to air bubbles. Taggart has shown that in pneumatic flotation machines collector-coated particles are only temporarily attached to bubbles. They keep falling off and down in the froth but at a delayed rate as compared with gangue. Spedden and Hannan&apos;s motion pictures confirm the difficulty of attaching particles to air bubbles. In the agitation froth process, according to Taggart, air is precipitated from the water selectively on to the collector-coated particles and these

Jan 1, 1951

By T. M. Morris

G. L. Simard and D. J. Salley—The authors and ourselves" independently came to similar conclusions both as to the value of tracer methods for the study of flotation and the general nature of collector-mineral interaction. The dodecylamine-quartz system appears to be simpler than the dithiophosphate-galena one, and the results therefore appear clearer. It is evident from a comparison of the two papers, however, that care must be used in extending the results to other more complicated systems. In the case of dodecylamine-quartz, the possible influence of micelle formation is of interest. There is no a priori reason why complete monolayer formation should necessarily occur at the concentration for micelle formation, since sorption depends on the nature of the substrate as well as on the properties of the solute in solution which alone determine micelle formation. Indeed, the fact that the onset of increased adsorption, point B in fig. 2, occurs at a concentration one tenth the critical value for micelles might imply that micelle formation does not have an influence. Interestingly enough, the data may be handled by the methods used for multilayer adsorption of gases on surfaces. Thus, if the amount adsorbed is plotted versus concentration, a sigmoid type curve is obtained, similar in form to a so-called Type I1 isotherm13 generally attributed to multimolecular adsorption. A monolayer value of about 0.12 mg per g may be estimated from the knee of this isotherm. On the other hand, if a plot is made according to the multilayer gas equation for adsorption to an unrestricted number of layers, eq 38,13 assuming the critical micelle concentration as the saturation concentration, the data above 120 mg per liter fall on a straight line from which a monolayer adsorption of 0.3 mg per g results. These considerations suggest that the monolayer may occupy an area somewhat less than the geometric value of 0.4 mg per g, and that micelle formation may indeed be a factor in the adsorption. the angle between the solid-liquid and liquid-gas interfaces, measured through the liquid. The value of the equilibrium contact-angle is uniquely determined by the value of the interfacial energies of the three intersecting interfaces and is independent of other forces in the system. When the liquid-gas interface intersects the solid at an edge—as was the case for all the experiments reported in this paper—the orientation of the solid-liquid interface is indeterminate or varies through 90" for a right-angle edge. Mr. Morris has called the angle between the horizontal and the liquid-gas interface for this edge condition a "static contact-angle." I feel that this term is unnecessarily misleading. In the first place, "static contact-angle" sounds too much like "equilibrium contact-angle." In the second place, the magnitude of the "static contact-angle," which I would prefer to call the "supporting angle," is determined by the forces in the system other than those derived from the interfacial energies, hence "contact angle" is misleading. If Mr. Morris had said that the "supporting-angle" is variable and depends on the weight of the particle and size of the bubble and that it has a maximum possible value equal to the equilibrium contact-angle, his discussion would have been more accurate. T. M. Morris (author&apos;s reply)—Mr. Kellogg puts forth a reasonable criticism of some of the terminology used in the paper. I agree that the term "static contact angle" may be misleading. Substitution of the term "supporting angle" or "vector angle" may be more suitable. F. X. Tartaron—In this paper the author presents a very interesting mathematical development of the forces present when a mineral particle adheres to an air bubble. Excellent concordance is obtained between mathematical formulation and experimental results. It is the writer&apos;s understanding that when the mineral surface presented to an air bubble is greater than the area of contact, the maximum contact angle is obtained. However, this contact angle represents distortion of the bubble, the normal shape of which is spherical or in cross-section, circular. This distortion produces a force that acts in opposition to the force of adhesion between the bubble and particle. Hence, at maximum contact angle, the force of adhesion between bubble and particle is at a minimum for static conditions. However, when the size of bubble is increased, the size of particle remaining the same (and all other conditions remaining the same), the contact angle decreases, the distortion of the bubble decreases and the force in opposition to adherence of bubble and particle also decreases. Thus, there is stronger attachment between bubble and particle. When this situation is applied to actual flotation conditions, it is doubtful that it has any significance. The reason is that the bubbles are normally so much larger than the particles, that in substantially all cases, it is probable that negligible distortion of the bubble takes place. In table IV, the author makes computations for bubbles from 0.50 to 2 mm diam. This is from 0.02 in. to 0.08 in. Certainly the bubbles generated in a flotation machine are far larger than this. The surfaces of the author&apos;s bubbles range from 0.79 to 12.6 sq mm. The area of contact of the glass rod (0.15 mm diam) is 0.017 sq mm. Thus, ratio of bubble surface to mineral area of contact ranges from 47 to 741 in round numbers. If we take a %-in. diam bubble and a 65-mesh (0.208 mm) particle of cubical shape, the ratio of bubble surface to mineral area of contact is 2931. Mineral particles do not readily become attached to air bubbles. Taggart has shown that in pneumatic flotation machines collector-coated particles are only temporarily attached to bubbles. They keep falling off and down in the froth but at a delayed rate as compared with gangue. Spedden and Hannan&apos;s motion pictures confirm the difficulty of attaching particles to air bubbles. In the agitation froth process, according to Taggart, air is precipitated from the water selectively on to the collector-coated particles and these

Jan 1, 1951

By N. J. Grant, Per Knudsen, J. T. Blucher

The fatigue behavior of three SAP alloys was studied in ternzs of strain rate and temperature, at high strains. The k values in the modified Manson-Coffin equation, Nk4 = C, were less than 0.5 under all test conditions, and change with strain amplitude for the lower-oxide alloys at about 2 pct strain. Lowest k values were near 0.25. Strain rate had no effect on life at 80 F, but had an increasingly greater effect with increasing temperature above 500". Life decreased with decreasing strain rate, above 500"F, and with increasing temperature. Ductility at fracture in a tension test was indicated to be an important factor in determining 1ife in these big+-strain tests with the SAP alloys. INEVITABLY, in the course of mechanical tests at elevated temperatures, particularly if significant time at temperature is involved, there are large changes in structure; these changes make it difficult to relate behavior patterns over ranges of temperature or strain rates at high temperatures. Such changes are to be expetted in low cycle fatigue at low strain rates and high temperatures. Accordingly, it was of great interest to examine the low cycle fatigue behavior of SAP / an aluminum oxide dispersion-strengthened aluminum, a type of alloy which had shown unusual structure stability to temperatures as high as 1000" to 1150°F and resisted recrys-tallization essentially to the melting temperature.&apos;j3 Since the matrix is pure aluminum, there are no complications of averaging, agglomeration, or phase solution. It was also desirable to check the Manson-Coffin equation4?&apos; for the SAP alloys, namely N~E~ = , where ep is the total plastic strain amplitude, k and C are constants, and N is the number of cycles to failure. Here, too, was an opportunity to check the roles of temperature and strain rate with a very stable material. Tavernelli and coffin6 had concluded that k had a value of about 0.5 for many alloys and C was equal to ~/2, where E is the fracture ductility determined from a static tension test. The results were obtained from low-temperature tests where creep and diffusion processes are unimportant. Manson7 found k = 0.6 fitted his data reasonably well; however, in later analyses of a large amount of low cycle fatigue data generated at room temperat~re@"~ he found k to vary from 0.6 for short lives to 0.21 for long-life fatigue tests. In the latter studies,89g Manson separated the total strain range into elastic and plastic components when he found that k was influenced by the nature of the strain. The use of EL (total strain) instead of EP (total plastic strain)4&apos;5 makes a difference in the resultant k value. The ratio of changes with temperature, strain rate, and strain; further, there are the problems in the determination of the elastic strain. Based on these considerations, and the improved fit of points in a plot of by Wells and Sullivan,&apos; is also utilized in these studies. Anderson and wahl,14 using commercial 1100 aluminum, and Blucher and Grant,15 using 99.99 pct pure aluminum, found an increase in life with increasing test temperature. Anderson and Wahl were the first to report low cycle fatigue results from SAP materials. With increasing temperature, the role of strain rate becomes more important. In this regard, care must be exercised to differentiate between frequency (wherein strain rate may vary from zero to a maximum in each cycle, sinusoidally, for example), and constant strain rate, as used in the present study, in a saw-tooth type cycle; in the latter case, the frequency is not specified but can easily be calculated from the strain and strain rate data. It has generally been found that life in low cycle fatigue tests decreases with decreasing frequency16 or with decreasing strain rate at elevated temperatures.15 Coffin,17 reviewing Eckel&apos;s work,16 also reported that k increased with decreasing frequency for acid lead, yielding values from 4.0 at a frequency fo 6.6 cycles Per day to 1-46 at a frequency of 7440 cycles per day; the value of k decreased to 0.58 at a frequency of 2.38 x lo6 cycles per day. EXPERIMENTAL PROCEDURE Three SAP alloys, of two nominal compositions, were tested. Alcoa supplied XAP 005 as 2-in.-diam extruded bar, of nominal composition A1-7 wt pct A1203. The Danish Atomic Energy Commission supplied SAP 930 (A1-7 wt ~ct Ala3) and SAP 865 (A1-13 wt pct Al&) manufactured by Swiss Aluminium Ltd., in the form Of $-in.-diam extruded rod. Metallographic comparison of the structures of XAP 005 and SAP 930 showed the former to have a more uniform oxide distribution. Button-head specimens were machined in the longitudinal direction of the bar with 0.4 in. gage length by 0.2 in. diameter, with a fillet radius of j-B in. After machining, the specimens were electropolished in a 1 to 4 mixture of perchloric acid to methanol to remove all machining marks. All test bars were in the as-extruded condition. The fatigue tests were performed on a hydraulically activated, axial strain machine, with complete reversal of strain.15 Test conditions were:

Jan 1, 1969

By Richard H. Olson

"Rarely in our technological society does the discovery of a new class of inorganic materials result in such a wide scientific interest and kaleidoscopic development of applications as has happened with the zeolite molecular sieves." The foregoing, the opening sentence in a landmark volume on zeolite molecular sieves by D. W. Breck (1974), is, if anything, an understatement. Zeolites were recognized as a new group of minerals in the 1750s, but it was not until 1930 that the first analysis of the crystal structure of a zeolite mineral was made. In the late 1940s research workers at Union Carbide Corp. began a program of zeolite synthesis and study which has resulted in one of the major research achievements of all time. Naturally, with the vast research and development efforts devoted to the synthetic molecular sieves, Union Carbide became concerned in the mid-1950s about its position should minable deposits of natural analogues be discovered. Zeolite minerals have diverse origins, and even a brief discussion of these is beyond the scope of this paper. The early work on zeolites was confined to igneous rock occurrences (e.g., amygdules and veins) which were formed by "space-filling;" these crystals tend to be euhedral, thereby rendering them appealing to both mineralogists and collectors. During the first year or so of Union Carbide&apos;s exploration (which began in mid-1957) attention was devoted solely to such igneous occurrences. A landmark paper by Bramlette and Posnjak (1933) heralded the potential significance of the occurrence of zeolite minerals as alteration products of vitric ash and similar materials. In the summer of 1958, full attention was directed by Union Carbide to the search for deposits of this type in the western United States. Since then, such exploration has been continu-

Jan 1, 1975

By Ben-Zion Weiss, Melvin R. Meyerson

FATIGUE crack propagation in some aspects can be viewed as being a result of localized plastic deformation concentrated near the tip of the crack.&apos; Deformation is influenced by microstructure which in turn can affect the fatigue crack growth significantly. To study the effect of localized microstructural changes on fatigue crack propagation, cantilever-type notched specimens were subjected to cyclic bending at constant load amplitude. The extent of fatigue crack propagation was obtained by measuring the length of the crack by periodic observation with a microscope on the polished side of the sample,2"4 and these data were used in preparing the curves in the figures which follow. Figs. 1 (solid lines) and 2 show experimental results obtained in austenitic type 302 stainless steel containing higher than standard carbon (0.24 pct C) and 310 stainless steel. Both steels were homogenized for 8 hr at 1120°C and then water-quenched in order to prevent the precipitation of carbides. Fig. 3 shows experimental results obtained on 9440 low alloy steel in the normalized condition and in the quenched and tempered (580°C) condition. Indications of microstructural influence can be seen in scattering of the experimental data. The degree of scattering depends on both the microstructure and the amount of cyclic stress applied to the sample. For microstructures which are more easily deformed plastically, e.g., normalized or annealed as compared with hardened and tempered structures, the scattering is greater. Similarly, higher stresses produce greater scattering in the results, regardless of whether the cause of the stress increase is due to initial loading conditions or the growth in crack length. Scattering is believed to be a result of partial redistribution in the stress field around the tip caused by plastic deformation. This opinion is borne out by much smaller scattering of experimental results in the austenitic 302 high-carbon (0.24 pct C) steel. In this steel, plastic deformation in the neighborhood of the crack causes partial mar-tensitic transformation of metastable austenite,5 which in turn restrains further plastic deformation. As a result, the stress redistribution around The tip is reduced. Partial martensitic transformation was confirmed

Jan 1, 1969