Search Documents

By Xuan Li

Aluminum slag is generated when aluminum metals are recycled through a smelting process in the presence of salt. There are small amounts of aluminum metals trapped in the aluminum slag. This research aims at evaluating the use of aluminum slag as an expansion agent for the production of lightweight concrete by taking advantage of the residual aluminum metals in the slag. The research identified key elements of producing lightweight concrete products through utilizing various mixture components including sodium hydroxide (NaOH), lime (CaO), cement, and gypsum. The volumetric expansion rate was investigated and the density and strength of the products were determined. The results show that aluminum slag can be utilized for the production of lightweight concrete products.

Jan 1, 2010

By Jilai Xue

Experiments with various industrial cathodes ranging from 35 wt.% to 100 wt.% graphitic and fully graphitized carbons were carried out in a laboratory aluminum electrolysis cell. Sodium and cryolite bath penetration into the cathode samples was measured by XRD and SEM-EDS analysis. For a higher cryolite ratio in the bath, the cathodes with lower graphitic carbons exhibited more sodium penetration than the fully graphitized. The increased graphitization in the cathode materials can reduce Na, NaF and Na3AlF6 penetration. SEM-EDS inspection reveals that the sodium and fluorides penetration within the cathode samples has different patterns for varying graphitization of the carbon materials. XRD quantitative analysis indicates that there is a large percentage of Na3AlF6 in the penetrated bath. The results can provide useful information for quality evaluation of the industrial cathode products.

Jan 1, 2010

By A. J. Dudzik

In 2006 Arch Materials initiated the development of an underground limestone mining complex. The decision to proceed with the project was the end result of several years of market research and geological reconnaissance. The scope of the project included the construction of two declines to the mining horizons located approximately 900 feet below the surface, the means and methods of this phase will be the primary focus of this discussion. The design, fabrication and erection of a state of the art crushing and screening processing plant which when completed will have the primary crushing located on the mine level allowing uniformly sized material to be brought to the surface by means of a highly efficient conveyor system and a surface portion of the plant where material would be additionally processed, screened and stockpiled into specific product types. Also included in the scope of the project is the construction of offices, warehouse and shop facilities necessary to support the operations, commercial sales and distribution of the finished products.

Jan 1, 2010

Growing concerns of climate change and its potential association with the release of greenhouse gasses to the atmosphere have prompted possible legislation which would require minimization of greenhouse gas emissions. Carbon dioxide and methane, both of which largely contribute to the greenhouse effect, have direct links to the fossil energy industry sector. Specifically, the combustion of one ton of coal produces between one and three tons of carbon dioxide, dependent upon the carbon content and heating value of the combusted coal. Additionally, coal mine methane (CMM) released through a mine?s ventilation system has a radiative trapping impact approximately 20 times greater than that of an equivalent mass of carbon dioxide. The capture of coalbed methane (CBM) prior to the mining process and its utilization as an alternative energy source provides the possibility of a decreased carbon footprint. Domestically, the past 25 years have seen a significant expansion of the CBM industry. Internationally, in developing countries such as China, the need for western coal degasification technology is growing. A collaborative, international effort will be required to initiate a recognizable decrease in global greenhouse gas emissions. This paper identifies the potential decrease in equivalent carbon dioxide emissions through effective degasification at a hypothetical longwall mine located in China. Advanced, three-dimensional gas reservoir simulation software will be utilized to determine the maximum feasible CBM recovery in a low permeability, high gas content reservoir prior to the mining process.

Jan 1, 2010

By Laxman S. Sundae

Laboratory tests were conducted at the U.S. Bureau of Mines to determine the effects of roof-bolt drilling parameters on penetration rate in sandstone using tungsten carbide alloy (WC-Co) and polycrystalline diamond compact (PDC) drill bits. During the tests, water pressure of 552 kPa was found to be adequate for removing the cuttings from the tops of drill holes. Test results show that for both types of bits, penetration rate increased when thrust was raised from 227 to 1,588 kg. When water pressure rose from 554± 120 to 1,344±350 kPa, the effect on penetration rate was not significantly different. Conventional WC-Co bits became dull when one or two holes were drilled, after which the penetration rate dropped dramatically. Microscopic examination shows that the cutting edges of PDC bits also become somewhat dull, but at a much lesser rate than WC-Co tips. Microscopic examination also reveals that the wear mechanism of WC-Co and PDC bits is quite different, which may explain the longer life of the PDC bits.

Jan 1, 2010

By W. H. Strickland

Ultrasonic ranging sensors are inexpensive, have no moving parts, have no lenses to clean, are normally small and unobtrusive, and can measure distances through moderate amounts of dust, smoke, and humidity, so they are well suited to underground mines. In the work reported here, conducted by the U.S. Bureau of Mines, researchers tested ultrasonic ranging sensors for their ability to define rib line features for computer-aided navigation of underground mine mobile equipment. The investigation began with laboratory tests of field of view, angle of incidence, intersensor variation, and ranging accuracy of the individual rangers in a ring array produced by Denning Robotics of Wilmington, MA, The results showed that the sensors have good accuracy and low variability. Additional experiments at AMAX'S Henderson Mine showed the sensors could accurately and reliably measure the distance to mine features, including convex and concave corners and rib intersections. The results showed that when used properly, the ranger data are accurate enough for reliable mine vehicle navigation. When used incorrectly, ultrasonic rangers do not provide the anticipated data. Therefore, this report explains the principles of ultrasonic range measurement, describes the ranger's strengths and weaknesses, and explains proper ranger use and data analysis.

Jan 1, 2010

By R. L. Levens

The Underground Injection Control program was promulgated in 1981 by the U.S. Environmental Protection Agency under the provisions of the Safe Drinking Water Act. Placement of mine waste backfill underground is considered underground injection under the provisions of this program. A major issue is whether mine waste that is regulated as a contaminant source on the surface should be disposed of underground. The U.S. Bureau of Mines conducted research to investigate the impacts of mine waste sandfill on the quality of ground water. Analyses of water samples collected before and after contact with sandfill in a 10-year-old stope, as well as samples of the sandfill itself, were used to ascertain the influence of the sandfill after mine closure and subsequent flooding. Computer models supported the hypothesis that oxidation of pyrite by oxygen, accompanied by dissolution of carbonates, was the predominant reaction controlling the quality of the water being discharged from the stope. Concentrations of metals released as a result of acid production remained near or below detection limits. Metals release after mine flooding is expected to remain low as a result of the buffering by the sandfill and the reduced rate of oxidation.

Jan 1, 2010

By J. S. Hansen

The U.S. Bureau of Mines developed a system for casting unique, slotted steel armor by modifying the conventional expendable pattern casting (EPC) process that is normally used for making aluminum castings. Three innovations were added to the EPC process to make the successful adaptation: (1) Vacuum was applied to sand molds, (2) continuous narrow-necked feeding systems were used to permit the casting of thin walls, and (3) fixtures were designed to prevent pattern damage and to hold critical casting tolerances, Potential problems and defects are described.

Jan 1, 2010

By A. K. C. Chan

Recent hotel investment projects in China often involve very tight programmes for design and construction. An example given in this paper involves a 24-storey reinforced concrete hotel tower with 460 bedrooms and a 3-level podium commercial complex. The building is supported by relatively widely spaced columns and shear walls below which 88 number large diameter piers were excavated through fill, silty and bouldery clay on to dolerite and slate at depths between 15 to 3 0m below ground level. Whereas much experience has been accumulated in Hong Kong, hand-excavated pier foundation was only adopted for the first time in Dalian. This paper describes and discusses the various factors influencing the choice of the type and design of the foundation system. The criteria for determining appropriate founding levels are then explained. During installation, revisions to the acceptance procedure were made to cater for local conditions. Emphasis is placed on the role of the geotechnical engineer in making on-site decisions during construction. The advantage of the foundation system in accommodating on-site changes resulting from local complex ground conditions is demonstrated. The pier foundations were successfully completed ahead of programme.

Jan 1, 2010

By Valois R. Shea-Albin

An accurate assessment of the vertical stress on a coal seam at depth is important for mine design. Vertical stress calculation techniques presently available either are not sufficiently accurate or cannot handle complex surface topography. Therefore, the U.S. Bureau of Mines developed a computerized method to calculate vertical stress exerted on surfaces at depth that includes the effect of topography. Two input data sets are required: a digital elevation model containing topographic elevations and a coal seam file defining coal seam elevations at depth. Boussinesq's equation then quantifies the vertical stress resulting from topography. The computerized method was tested on a coal seam overlain by a complex topography where a vertical stress map encompassing several square miles was produced. Results show that depth mitigates the affects of surface topography, while the coal seam topography has a direct effect on the vertical stress. In comparison to the computerized method, the direct stress method overestimates stress under hills and underestimates stress under valleys. The largest difference between the two methods occurs under the steepest topographic relief. A limitation of the computerized method is that stresses cannot be accurately determined near an outcrop.

Jan 1, 2010

By W. P. Stroud

In this U.S. Bureau of Mines report, the conditions required for the direct reconstruction of a tomogram from observed line integrals are examined. Because of the limited access to the working faces in coal mines, the special case of access to only two opposite faces is emphasized. Classical matrix methods were used for small dimensional (2 by 2, 3 by 3, and 4 by 4) applications to determine the limitations and the requirements for a solution. The results for large (n by n) grids were then inferred and generalized from those of the smaller grids and matrices. Limited access tomography is found to be appropriate for in-seam hazard detection from seismic and microwave data, but it is shown that additional data must be added to obtain a direct solution.

Jan 1, 2010

By Tony Lipiec, Greg Gosson

"When it comes to new mines being developed, there is a general industry consensus that most low-hanging fruit has been picked. Many projects currently in the mine development pipeline have been around for decades, but were held back because of technical challenges. Future development of these deposits will likely require access to the public capital markets, and in Canada that means providing scientific and technical disclosure on these deposits in compliance with NI 43-101. As many of these “challenged” projects have metallurgical issues, the companies that own the projects need to ensure their metallurgical Qualified Persons provide transparent disclosure regarding proposed solutions to those issues.This paper provides an overview of the disclosure requirements under NI 43-101 that are pertinent to metallurgists, and other Qualified Persons who prepare technical disclosure regarding the metallurgical characteristics of a mineral project. It lists the triggers for a technical report under NI 43-101 and Canadian stock exchange policies, and identifies the sections of the report that should involve input from a metallurgist or process engineer. It briefly outlines new civil liabilities under Canadian securities laws that increase the possible consequences for not complying with the technical disclosure standards.These materials are provided for general information purposes only and do not constitute legal advice. Readers are advised to seek specific legal advice from their own legal counsel in relation to any decision or course of action contemplated."

Jan 1, 2010

By Joner O. Alves

The disposal of scrap tires has been a serious environmental problem. The treatment of this waste by pyrolysis and combustion has advantages since the landfill space is dwindling and the production of fuel becomes of technological interest. However, that processes needs a rigid control of emissions. This work presents a study of the light hydrocarbon gases (HC) generated during the burn of waste tire chips in a two-stage laminar-flow horizontal furnace. Different temperatures in the primary and secondary stage of the furnace were tested, and the oxygen/nitrogen percentage was also varied during the combustion process. A gas chromatograph was used to identify and quantify the components of the gaseous products of combustion and pyrolysis. The results showed the behavior of the gases during the burn of tires, providing valuable information to the control of hydrocarbon emissions.

Jan 1, 2010

By D. R. Zuchelli

The purpose of wrapping ball mills with thermal/acoustic blankets is twofold: 1) to maintain the desired temperature inside the mill, and 2) to reduce the sound emanating from the mill. This field case study focuses solely on the latter, evaluating and documenting the sound level reduction attributed to the installation of the blankets on ball mills and its potential to reduce the noise dose experienced by the process attendant. One of the three ball mills had already been treated (baseline) before the evaluation started. However, treating the remaining two mills still proved to be very effective, further reducing ball mill noise in the near field by as much as 10.0 dBA and producing far field noise reductions of 3.0 dBA or greater, extending as far as 35 feet from the mills and to the floor above. The model developed from the survey data shows that a process attendant spending a substantial portion of a shift in the mill building will experience a significant reduction in overall noise dose.

Jan 1, 2010

By T. Eggenberg

Mechanization and automation of logistic equipment has become one of the main key factors in raising productivity and competitiveness especially for complex and larger mining or tunneling projects. The Lake Mead Intake Tunnel #3 shaft mucking installation is a good example to demonstrate the potential that is found in an overall optimized logistic. It starts with the planning and results in using customized installations which fulfill the specifically defined requirements for the project. Rowa developed a solution and supplied a shaft mucking system using a discontinuous double drum hoisting concept with shaft buckets, loading, and unloading devices. With this fully automated system a continuous muck flow of 437t/h can be achieved.

Jan 1, 2010

By María Cristina Ruiz

Enargite rich copper concentrates can not be treated by conventional smelting/converting technology and thus nonconventional methods such as leaching must be used. Since enargite (Cu3AsS4) is a hard to dissolve mineral in acidic solutions, pyrite, a common impurity in copper concentrates, could be used to increase the enargite dissolution rate. On this matter, we present in this work experimental data on the pressure leaching of a mixed enargite-pyrite concentrate in H2SO4-O2. The results show that the dissolution of enargite from the mixed concentrate is considerably faster than the dissolution of pure enargite mineral. The leaching rate increases significantly with temperature. Over 98% of enargite was dissolved in leaching 64 micron size particles at 200 ºC and 100 psi of partial pressure of oxygen in just 30 minutes. A change in the partial pressure of oxygen from 50 to 150 psi showed also a large influence in the leaching rate.

Jan 1, 2010

By Thomas M. Barczak

This U.S. Bureau of Mines (USBM) report evaluates the load supporting characteristics of grout columns used as point supports for mine subsidence abatement. The cone-shaped columns were constructed with sodium silicate and cementitious grout in both wet and dry environments. The scope of work included the testing of seven full-scale grout columns in the USBM's Mine Roof Simulator from which the load-deformation and failure characteristics were determined. The performances of grout columns are analyzed with respect to (1) the amount of roof contact established during column construction, (2) shape effects produced by the truncated cone geometry, (3) size effects in reference to grout strength and full-scale column capacity, (4) the effect of wet environments on grout strength, (5) the effect of the sodium silicate on the grout strength and full-scale column behavior, and (6) the stiffness of the grout column. Limited tests were also conducted on cylindrical columns constructed in fabric bags. Recommendations for point support construction using sodium silicate technology and the need for additional research to develop improved containment devices for column construction are addressed in the report.

Jan 1, 2010

By Craig C. Hustwit

A pilot-scale treatment study was conducted on a copper-zinc bearing metal mine drainage using a pipeline treatment system called the In-Line System (ILS). The objective of this U.S. Bureau of Mines study was to determine whether the ILS could be extended from the treatment of coal mine drainages to the treatment of metal mine drainages. Hydrated lime (Ca(OH)2), quick lime (CaO), and caustic soda (NaOH) were used to neutralize the drainage. A novel reagent slurry of Ca(OH)2 and type C fly ash was also evaluated. Except for Ca(OH)2-fly ash slurry, treatment performance was evaluated for all reagents at pH values of 7,8,9, and 10. The Ca(OH)2-fly ash slurry was evaluated at a pH of 10. All reagents tested neutralized the metal mine drainage and substantially reduced the dissolved metal concentrations. It was concluded that the ILS could be useful in the treatment of metal mine drainages.

Jan 1, 2010

By William P. Stroud

Chemical alteration of the compressive strength of sandstone has been investigated by the U.S. Bureau of Mines (USBM). Successful development of this technology would offer an attractive alternative to the methods now used for stress control in mines. Sandstone cores were stressed to failure under uniaxial compression at two different strain rates. Specimens saturated with either distilled or tap water showed an average 14% reduction in stress at failure compared with those dried in vacuum. Samples saturated with dilute solutions of aluminum chloride, hydrochloric acid, and polyethylene oxide showed no statistically significant difference in failure stress compared with those saturated with water. By contrast, compressive strength of the cores was increased some 7% by saturation with the nonpolar solvent carbon tetrachloride. No correlation was found between zeta potential and compressive strength.

Jan 1, 2010

By Frederick C. Rhyner

This paper describes the design and construction of two high-capacity rock anchors to restrain a supplementary backstay for the Bear Mountain Bridge, which is a suspension bridge spanning the Hudson River about 40 miles north of New York City. The supplementary backstay was installed to relieve a portion of the tension in the southern main cable, which had been creeping in recent years. The two new rock anchors were 1,200 kip capacity each, installed at a batter to depths of 59 feet. This paper describes the subsurface investigation, group capacity analysis, installation and load testing. The rock anchors included strain gages connected to the monitoring system for the bridge. The paper describes the long term strain gage data which shows no change in stress distribution in either anchor.

Jan 1, 2010