Search Documents

1880 - 1930 - The Golden Years of Mineral Processing Technology

Sep 13, 2010

Advances in Thickener Feedwell Design via Computational Fluid Dynamics Modelling

Sep 13, 2010

Effect of Hardwater on Selective Flocculation of Diasporic-Bauxite

Sep 13, 2010

Spectroelectrochemical Investigation of Hydroxamate Reagents on Copper Oxide Minerals

Sep 13, 2010

Study on Flotation of the Low-Grade Magnesite Ore

Sep 13, 2010

Pilot-Scale Study of Deep Cone Thickener for Phosphatic Clay Dewatering

Sep 13, 2010

Enhancement of Energy Efficiency in Fine Grinding of Copper Sulfide Minerals Using a Pilot-Scale Stirred Media Mill - IsaMill The mineral liberation size of run of mine ores has dramatically reduced over recent years. As a result, the demand for fine grinding which is the most energy-intensive form of grinding has markedly increased in the minerals industry. Furthermore, the fine grinding costs increase exponentially with decreasing product particle size. As a result of the increased energy requirement for fine grinding, it is desirable to optimise fine grinding processes such as stirred media milling (ie IsaMill) to enhance energy efficiency, throughput and the product fineness. In the present study, the influence of slurry rheology, grinding media type and grinding media-to-feed size ratio on energy efficiency in a pilot-scale IsaMill was investigated under certain industrially relevant pulp processing conditions. It was shown that a critical rheological state existed, below which the energy required to achieve an 80 per cent passing (ie P80) 20 ¦m product size was unaffected by shear rheology (ie apparent viscosity and shear yield stress) whilst above which the grinding energy required increased dramatically with increasing shear rheology. Colorado River sand (3.35 mm) showed higher energy efficiency than MT1 ceramic media (2.5 mm) for a target P80 of 20 ¦m in the solids concentration range of 38 to 55 per cent by weight, but the former experienced more than four times the wear rate of the later. The high wear rate of the Colorado River sand may be due to its much lower hardness. For feeds with an 80 per cent passing (ie F80) 70 to 110 ¦m, 2.0 or 2.5 mm MT1 media appeared to be more energy efficient than 3.5 mm MT1 media whilst a media-to-feed size ratio of 41 to 53 is applicable for ~50 ¦m (ie F80) feeds for efficient grinding.

Sep 13, 2010

Grinding Mill Operation and Maintenance - Central to Asset Management Since 2005, RME has pursued a vision for a new grinding plant operational paradigm, made possible by RME's latest Mill Relining Systems. At some sites, new liners degrade SAG mill performance. The variables include mill volume loss, rotational speed limitations (ball strike) and liner designs developed for longer and longer life but without a backward glance at metallurgical consequences of whole plant performance. Freshly relined mills can initially deliver as little as 80 per cent of their maximum throughput, that maximum occurring toward the end of the liners' wear life. RME's proposition is to see new liners designed for maximum commercial performance. This may mean more frequent mill relines but with liners designed to yield optimum grinding, metallurgical and profitability performance, not maximum life. In other words, mill liner profiles and relining speed become key profitability contributors and not simply 'must do' maintenance functions and costs. This paper includes a short history of RME's Mill Relining System development (Appendix A). These are the enabling technologies which permit more frequent liner exchange without incurring additional downtime imposts. The body of this paper outlines RME's vision of a 'liner profile vs. profitability' commercial model, underpinned by the rigour of PAS 55-1:2008 Asset Management Part 1: Specification for the optimised management of physical assets. The technical elements can be developed either intuitively (based on plant experience) or by using a combination of new measurement and modelling technologies. These new measurement and modelling tools provide the opportunity to predict the optimum technical solution for the maximum commercial outcome. Much of this can be modelled off-line, in the virtual world, before asking senior management to commit to an expensive liner experiment. The potential benefits are compelling.

Sep 13, 2010

Au-Ag Recovery from Complex Ore by Flotation

Sep 13, 2010

Towards Improved Hydrocyclone Models - Contributions from Computational Fluid Dynamics

Sep 13, 2010

Recovery Efficiency Study on Ilesha Placer Gold Ore by Flotation Using Locally-Sourced Frothers and Collectors

Sep 13, 2010

Ultrasonic Extinction for High Resolution Particle Size and Concentration Analysis

Sep 13, 2010

Water rights and availability are extremely contentious issues in many mining regions around the world, in some instances leading to violent confrontation. This situation has the potential to only get worse because competition for 'scarce' water resources will increase with population growth. In this environment the dilemma facing the mining industry is how to generate confidence in developing a responsible, sustainable and transparent water management strategy that is recognised as such by all stakeholders. Whilst the water needs of the mining industry are minor compared to those of agriculture, an operating mine requires a relatively large quantity of water on a daily basis to carry out operations. Another contentious aspects of new mine development is the debate between all stakeholders on the amount and quality of water that a mine is able to discharge into the environment should this be required. There are a multitude of water resources available to the mining industry for operational needs however much of this water is saline and over the last two decades there has been a continual decline in water quality (ie salinity has increased). In today's world there are enormous internal and external pressures to reduce water consumption at a mine and/or alternatively use water not considered a resource by the local community (ie sewage, saline or salt water, desalinated water). Strategies to meet these objectives can be achieved by implementing good water management practices, by recycling process water, reducing water losses by evaporation and seepage (ie by increasing and improving dewatering practices) and employing new technologies such as dry stacking and dry processing. Recycled water, acid mine drainage water and water collected in the mining area have the potential to impact mineral processing performance, unless they are treated, because of the build up of mineral salts and decomposed chemical products in these types of waters. Besides this the regulatory requirements of any water discharged from a mine site (quantity and quality) have also become more stringent. For these reasons there is now some form of water treatment practiced at most mining operations around the world. This paper provides an overview of water stewardship undertaken in the mining industry over the last two decades and provides examples of water treatment practices that have recently been installed at mining operations that may be of interest to the reader.

Sep 13, 2010

Techno-Economic Evaluation of a New Early Removal Process to Treat High-Arsenic Copper Ores

Sep 13, 2010

Autogenous-Carrier Effect and Gangue Influence in Fine Particle Flotation of Ilmenite/Titanaugite System

Sep 13, 2010

The Acid Leaching Process for the Synthesis of Zeolitic Material from Paper Sludge Ash

Sep 13, 2010

Inhibition of Bubble Coalescence by Salts and Sugars

Sep 13, 2010

Adsorption of Starch on Kaolinite Surfaces

Sep 13, 2010

CrusherMapperTM - A New Tool for Crusher Condition Monitoring The efficiency of mineral processing plants is entirely dependent on the availability of the plant equipment critical path. This typically concerns comminution circuits consisting of primary crushers and primary grinding mills. Crusher and mill availability are determined by the frequency and duration of maintenance shutdowns, which are primarily driven by the need for replacement of sacrificial liners. The change of crusher and mill liner shape over respective life cycles also strongly affects plant efficiency. It is therefore highly desirable to accurately monitor the condition of mills and crushers in order to optimise plant efficiency through maximised availability and targeted liner shape. Traditional comminution liner and other production parameter condition monitoring has been attempted through ineffective methods which prevent satisfactory management of crusher and mill maintenance and reduce operational control. This situation has recently dramatically improved for grinding mills through the development and commercial deployment of MillMapperÖ, a technology based on three-dimensional laser scanning data and dedicated software (Franke, Lichti and Stewart, 2006; Franke and Lichti, 2007; 2008; Franke, 2008; Franke, Redman, Johnson and Michalek, 2009). At the time of writing in late 2009, MillMapperÖ is in successful use at a rate of approximately 170 surveys and associated reports per annum at processing plants in Australasia, South America, North America and Africa. This paper presents the introduction of CrusherMapperÖ, the MillMapperÖ equivalent for crushers. CrusherMapperÖ also utilises high density, high accuracy laser scanning data, and features dedicated algorithms for three-dimensional monitoring of wear on crusher concaves and mantles. This facilitates the detection of wear hot spots or zones or localised liner failures, and accurate forecasting of reline tonnages and dates. It also for the first time provides the means to establish optimised concave and mantle shapes in order to achieve production targets. In contrast to any other currently utilised condition monitoring method, CrusherMapperÖ data collection can occur remotely and does not require any shutdown or crusher isolation. This method therefore does not interrupt crusher production while at the same time eliminating any confined space risk normally associated with taking measurements inside the crusher cavity.

Sep 13, 2010

Role of Bubbles in the Action of Flotation Agents

Sep 13, 2010