Search Documents

By R. O. Ifill

Alternating current electrocoagulation (AC/EC) may be an alternative to chemical coagulation in the thickening of tailings in the mineral, coal and petroleum industries. In the current study, ground silica (d50 as received, 20 µm) served as the model tailings solid with characteristically poor settling behavior. Its natural initial settling rate was 1.6 x 10-3 cm/min. This paper discusses the indirect application of AC/EC via aluminum electrodes to the enhancement of the settling behavior of the silica. ?Indirect AC/EC? means that the silica was coagulated upon dispersion in water that had been treated by AC/EC. The effect of AC/EC retention time on settling behavior is examined and the water chemistry is analyzed. Test results show that the initial settling rate of silica was enhanced by a factor of 4,000 at its maximum of 6.4 cm/min, under the conditions employed. Settling enhancement was achieved upon contact between the AC/EC-treated water and the silica, and the enhanced initial settling rate was dictated by the floc size. The aluminum dosage increased with AC/EC retention time, reaching a maximum concentration that was equivalent to 13.1% of that predicted by Faraday?s law. Complex aluminum ions are considered to have adsorbed onto the silica surface and an adsorption mass ratio of 0.3 mg Al/g silica was the most effective in enhancing settling behavior. Owing to pH change or slow kinetics, aluminum hydroxide precipitation did not lower the ion product ([Al3+][OH-]3) below the KSP of 6.3 x 10-32.

Jan 1, 2011

By Alexander Nikolic

The paper presents the foundation design and construction of a landmark urban redevelopment scheme in central London, UK. The scheme comprises the new Tottenham Court Road Underground station, Crossrail interchange box and associated over-site commercial development. The paper focuses on the design, procurement and construction of large diameter bored piles, up to 68m in depth, which form the foundation support system for the over-site commercial development at Denmark Place. The congestion below ground required an intricate foundation design solution which has been a catalyst for developing innovative load transfer arrangements and has resulted in the advancement of pile construction technology in the UK. The foundation system was also designed to cater for the construction of two significant elements of proposed below ground infrastructure. Selected large diameter piles have been constructed within 1.1m of live underground railway tunnels. An innovative D-shaped pile was constructed in a zone subject to particular spatial constraints. The proposed Crossrail tunnels will be bored within 1m of selected over-site development piles. In addition, a 30m deep excavation forming a new escalator box will be constructed in direct contact with the over-site development piles. The stakeholder engagement process is described together with the foundation design development and buildability assessment. The benefits from early collaboration between the designers and specialist contractors are highlighted. From an analytical design perspective, the entire foundation construction sequence was modelled in detail in order to assess the soil structure interaction and any potential adverse effects on existing elements of underground infrastructure. The results from the three dimensional numerical modelling simulation are compared with field monitoring data.

Jan 1, 2011

By T. G. Joseph, A. Sharma

ABSTRACT: Ultra-class haul trucks operating in oil sand face operational and maintenance issues as a result of soft underfoot conditions (Joseph, 2002). With exposure to frequent high g loading events, tire life is reduced due to sidewall belt fexure and frequent ground contact. Therefore, an improved under-standing of the interaction between tires and oil sand is needed. This paper examines the outcomes of a series of static and cyclic loading tests, performed using a scale tire on rigid, sand, and oil sand surfaces. Geometric predictions are made regarding the footprint area and vertical deformation of an ultra-classtire on similar surfaces.

Jan 1, 2011

By Manqiu Xu, Andrew Lee, Frederick D. Ford, Cara Wercholaz

"Platinum-group minerals (PGM) typically occur in such low concentrations that quantitative mineralogical evaluation is difficult or impossible. The FEI MLA system used by Vale Base Metals Technology Development has been successfully employed to produce large PGM data sets that are statistically robust. The MLA Sparse Phase Liberation mapping routine produces false colored images that accurately document mineral textures, including intergrowths between various platinum group minerals and between PGMs and other tellurides and sulfides. MLA PGM search results can be used in conjunction with mineral chemistry to calculate platinumgroup element distribution to minerals and the MLA PGM images can be used to produce model grade-recovery curves.INTRODUCTIONThe platinum-group minerals (PGM) found in Sudbury area deposits have been extensively catalogued and reviewed by many authors including, but not limited to: Farrow and Lightfoot (2002), Cabri and Laflamme (1984; 1976) and Cabri (1981). The PGM list currently used has 12 minerals summarized in Table 1. As noted by Farrow and Lightfoot (2002), platinum-group minerals in Sudbury are dominated by tellurides, bismuth-tellurides and arsenides, with an absence of platinum-group element (PGE) sulphides or ferro-platinum alloys such as tetraferroplatinum - PtFe."

Jan 1, 2011

By J. Bouchard, A. Desbiens, M. Maldonado, R. del Villar

ABSTRACT: Despite many years of practical applications in mineral processing plants, the potential of column flotation has still not been fully exploited. The challenge in measuring some key variables is certainly an important contributing factor to this situation. Reliable online measurement of varibles, such as the froth depth, bias, gas hold-up, frother concentration, bubble surface area flux, and bubble size distribution, provides opportunities for the application of various advanced control strategies and real-time optimization based on an economic criterion. For several years, Université Laval’sLaboratoire d’observation et d’optimisation des procédés researchers have been working on these opportunities. This paper describes the most recent advances and current research trends.

Jan 1, 2011

By V. G. Papangelakis, S. Peters

Pressure oxidation of refractory gold ores can be conducted on ores with high carbonate content using just water or water with alkaline reagents to promote fast kinetics, and suppress the formation of elemental sulphur and CO2. In this work, a fundamental study was conducted to explore the silica-pyrite interaction in the presence of calcium and sodium carbonate. It was found that an alkaline environment increases the pyrite decomposition kinetics on one hand, but on the other dissolves silica, which encapsulates the dissolving pyrite thus hindering ultimately its complete decomposition.

Jan 1, 2011

By David Kwietnewski

Roadheaders are gaining widespread acceptance in North America as a means for mechanical tunnel excavation. Until recently, almost all of the large-scale North American tunnel projects were excavated one of two ways ? the tried and true drill-and-blast method or with the use of tunnel boring machines (TBM), the hi-tech super-excavators. TBMs enjoyed fast-growing popularity worldwide as TBM manufacturers offered greater technology to meet the demand of the civil tunnel industry in the late 20th century. Recently, though, more tunnel projects, large and small, can thank the brute force of a roadheader for getting the job done.

Jan 1, 2011

By Maribel L- Saucedo-Muñoz, Toshiyuki Hashida, Victor M. Lopez-Hirata, Shin-Ichi Komazaki

"Small-punch tests were conducted at 4, 77 and 293 K on three types of austenitic stainless steels JNl, JJl and JK2, which were solution treated, water-quenched and then aged at 923, 973, 1023 and 1073 K for 5 h. Small-punch test energy was employed for the evaluation of the aginginduced embrittlement behavior in these materials. Fracture surface of small punch test specimen for the solution treated steels exhibited a ductile fracture, showing the highest SP test energy values. The presence of intergranular brittle fracture was observed in aged specimens. Smallpunch test energy decreased significantly as the aging process progressed. The highest and lowest decrease in small-punch test energy with aging temperature occurred in JNl and JK2 steels, respectively. The decrease in small-punch test energy showed to examine appropriately the aging-induced embrittlement in these materials. The difference in aging-induced embrittlement behavior for these steels was explained based on the volume fraction of intergranular precipitates in aged samples.IntroductionA high level combination of strength and toughness is required for cryogenic structural materials used in the superconducting magnets of fusion nuclear reactor. This requirement is beyond the capability of conventional austenitic stainless steels [1]. The Japan Atomic Energy Research Institute (JAERI) developed new cryogenic JNl, JJl and JK2 austenitic stainless steels. The structure of superconducting magnets is supposed to be constructed by welding thick plates of this kind of steels. Thus, most of the components are exposed to thermal cycles. The slow cooling may cause microstructure changes in both the base material and weld zone. These changes may also decrease the fracture toughness of these materials at cryogenic temperatures. Therefore, it is important to study the effect of thermal aging on fracture toughness behavior for these steels. Konosu et al. [2] carried out a study of the effect of thermal aging on the mechanical properties for JNl steel using tension and fatigue tests. Kwon et al. [3] evaluated the deterioration in fracture toughness at cryogenic temperatures for the isothermally aged JNl steel by means of the Small-Punch (SP) test. No other reports were found about the cryogenic fracture toughness behavior for this kind of steels. To evaluate the cryogenic fracture behavior, the elastic-plastic Jrc value is a good alternative [4,5]; nevertheless, the standard required specimen size makes it difficult to be used for the fracture toughness evaluation in small zones."

Jan 1, 2011

By Leonardo Mota, Lucas L. da Costa, Milton B. Filho, Sergio N. Monteiro, Helion Vargas, Tammy G. R. Portela da Silva

"A natural biofoam extracted from the buriti palm tree has shown characteristics for potential substitution of synthetic foams. In the present work, a photoacoustic thermal characterization was performed on buriti biofoam samples. An open photoacoustic cell technique and a photothermal rise method performed under continuous laser illumination were employed in order to determine the thermal diffusivity and the specific heat capacity of such material. In addition to their intrinsic values (finger print), these physical parameters represent the light-into-heat conversion efficiency and the amount of heat stored per unit volume, respectively. The results showed that the buriti biofoam presents thermal properties that permit its use as an effective insulation material.IntroductionSolid foams are very light materials with increasing engineering applications [1]. A natural biofoam obtained from the petiole of the buriti palm tree (Mauritia flexuosa) has been recently investigated [2-4]. The evaluation of the buriti biofoam properties and the characterization of its microstructural aspects have shown that this biofoam has a potential as a new engineering material with very low density. Additionally, its reduced open porosity and low absorbed humidity revealed a promising material for packing and floating applications. In fact, this buriti biofoam, extracted from the palm tree natural of the north region of Brazil, is being used by the low income population as a modest substitute for Styrofoam® [1].As a potential insulating material, the buriti foam needs to be characterized in terms of its thermal and acoustic properties. A preliminary investigation [3] on the thermal behavior of this natural biofoam by thermogravimetric analysis, TGA, and its derivative, DTG, as well as differential scanning calorimetry, DSC, revealed parametric conditions associated with water loss and structural decomposition. Both the surface humidity and the release of hydration water were determined. Different decomposition events were attributed to both, more rigid as well as to more flexible molecular segments. Table 1 depicts technical data obtained so far for the buriti biofoam. These data are compared to those corresponding to Styrofoam®."

Jan 1, 2011

By R. C. D. Phillis

The management of critical resource inventories is an important productivity lever and a significant risk factor?risk in the sense that poor resource availability lends itself to disempowerment of workers, unsafe work practices, wasted spending (high unit costs),and poor quality of work (including mining waste/rework). Most underground platinum mines experience lost blasts that directly lead to reduced productivity. In most surveyed shafts, 30% of lost blasts can be attributed to shortages of critical material and/or equipment. The problem is prevalent despite the existence of conventional transitory surface and underground stores. This paper discusses the introduction of buffer stores as a complementary materials storage system in order to improve health and safety in mines as well as reduce lost blasts. Both quantitative and qualitative results have shown that buffer stores result in dramatic improvements in productivity and are readily acceptable by stakeholders. Keywords Buffer stores, lost blast.

Jan 1, 2011

By Shinichi Takagawa

The deep sea hydrothermal deposits are one of the most prospecting resources, and various works to develop these mines are now underway. There are also various methods for the pre-site survey of the mines: acoustic survey, electro-magnetic survey, and others. However, as a precise method at the final survey, drilling/coring is indispensable to confirm the three-dimensional distribution and to grasp the dignity of the ores for the final decision of industrialization. This drilling/coring at the final survey is done at many points with distance of 15~25m between each point for on-land deposits. This means that 1km by 1km square area requires (1,000m/25m)2 ~ (1,000m/15m)2 = 1,600 ~ 4,500 holes. The drilling/coring depths will be around 30m or more for the hydrothermal deposits. This depth seems very shallow, but because the stratum is very brittle and is very difficult to core, the average core recovery ratio is around 50%, and 0% core recovery happens very often. Thus, the indispensable work of coring for grasping the dignity of ores is a very difficult work although the coring depth is shallow, and also the required number of holes is enormous. Conventional drilling/coring method on the ocean is to use drillship. However, the cost is very huge. Recently a new technique has come out which is to use remotely controlled drilling machine on seafloor. This machine seems to have a very good performance. However, it is reported that the available inclination of the seafloor where the machine sits on must be less than 15 degrees. The sea floor inclinations of active hydrothermal vents area are usually very steep and slopes of 45 degrees or more are prevailing and it seems very hard to carry out drilling/coring for the machine at these steep slopes, although it is impossible to mine the ore at these areas because the temperature is too high to work there. The inclination of the sea floor at the dead or paused hydrothermal vents area where ore recovery is possible may be not so steep, and the machine may work well. However, the required number of holes is still a very heavy burden. In order to solve these problems, the author proposes a new concept of drilling/coring system operated from a conventional research ship. This concept is still a desk plan, but the author wants to realize this system at any means.

Jan 1, 2011

By A Frydrychewicz, J. Mirza, J. Lipkowski

The objective of this work was to understand the mechanisms of action of additives, such as thiourea, that enhance gold leaching in thiosulfate solution. The leaching reaction and surface passivation were investigated using linear sweep voltammetry. Leaching currents were determined using analysis of current-potential curves and the mixed potential theory. The gold-electrolyte interface was further characterized with surface enhanced Raman spectroscopy. The results show how thiourea prevents formation of oxysulfur compounds, which passivate the gold surface. Other molecules such as 3- m ercaptopropionic acid and L-cysteine were also studied as possible additives to prevent passive layer formation.

Jan 1, 2011

By Ruixiang Wang, Jinhui Li, Youjun Xiao, Daoling Xiong, Hao Chen

"Leaching solution prepared from spent battery materials contains large quantities of valuable metals, such as Cu, Ni, Co, Mn and Fe. Therefore, recovery of valuable metals from acidic polymetallic aqueous solutions is of great importance for every plant. In this work, a method is introduced of recovery of Ni, Co and Mn from polymetallic solution prepared by leaching spent battery material. The basic concept includes copper was removed through replacement by iron powder followed by iron precipitation in goethite method. The experimental results show that Cu can be removed 99% at least through replacement by Fe powder, and the removal of Fe can achieve 99% by goethite method. At the same time, the loss of Ni, Co and Mn are about 2%, 3 % and 2%, respectively. The process of differential removal of metals can be selected as the treatment alternative that combines simplicity, efficiency and reliability with low capital and maintenance costs. The purified solution which only contains Ni, Co and Mn can be used to prepare NixCoyMnz ternary system precursor.1 IntroductionNickel and Cobalt are very important metals which are applied in many fields, such as energy material and support material for some new material field. The world demands for such metals is progressively increasing, while raw resources are being depleted and with the constraints raised by the Law and related legislation assigned to protect the environment from hazardous wastes in the world. Nowadays study on reutilization of waste materials has great significance for achieving secondary resources recycling and preventing environmental pollution. There are many hydrometallurgy methods applied for dealing with these wastes, while they usually contain large quantities of valuable metals, such as Cu, Co, Mn and Ni, as well as impurities, such as Fe, Zn, and etc. Therefore, proper treatment of these leaching solutions prior to their discharge is of great importance, so that the contained valuable metals can be recovered.Separation and extraction of metals from leaching solution can use some methods through solvent extraction[l,2], ion exchange[3,4], precipitation with sulfide[ 5] or alkali[ 6] and electrolytic recovery[?]. Among the appropriate treatment alternatives, replacement and differential precipitation is the most attractive treatment that combines simplicity, efficiency and reliability with low capital and maintenance costs."

Jan 1, 2011

By J. Cayouette, . Blatter, P. Cousin

The Laronde mill was commissioned in 1988 and has been treating the Laronde Perim ore since 2000. The Laronde plant, situated in the Abitibi region of Quebec, has experienced mill expansions to accommodate 7500 mtpd and to recover gold and silver as well as important amounts of base metals (Cu, Zn, Pb). Ten sequential metallurgical and environmental processes are responsible for metals recovery and process viability. Over 200,000 ounces of gold, 4,5 million ounces of silver, 7000 tonnes of copper, and 78,000 tonnes of zinc are produced annually. In 2008, the Goldex plant began trucking high wade (35-45 Wt Au) pyrite sulphide concentrate (TCGO) for gold extraction at a newly constructed treatment plant, increasing gold output at Laronde by 40,000 ounces. In 2009, the high gold wade Lapa ore processing facilities were annexed to the Laronde plant increasing output by 120,000 ounces of gold. TCGO and Lapa productions are forecasted until 2018 and 2015 respectively, with known reserves of each mine. Today, up to 140 permanent employees run and optimise the Laronde plant operation. As a result, Laronde has intricacies intrinsic to a large and varied operation. The paper will outline the metallurgical highlights, challenges, and future outlook related to the treatment of each ore type (Laronde, TCGO, and Lapa)

Jan 1, 2011

By Fawad S. Niazi

Ever since the use of the cone penetration test (CPT) in geotechnical practice, attempts have been made to correlate CPT parameters with pile capacity components of unit end bearing (qb) and unit shaft resistance (fp), thus deriving multiple CPT-based pile design methods. These methods focus on "capacity" only without consideration to complete axial pile load-displacement (Q-w) response. Estimated capacities from these methods also exhibit considerable scatter without any consensus on their consistency. In addition, load-displacement curves obtained from axial load tests on highly expensive and extensively instrumented piles can exhibit different shapes. Nevertheless, a single value from the curve so obtained dictates the design capacity. Currently, there are at least 42 different criteria defining capacity with considerable variation in the values obtained thereof. The Randolph elastic solution, which provides a framework for analytical evaluation of pile load-displacement response, requires the profiles of soil stiffness. The fundamental soil stiffness defined by the small-strain shear modulus (Gmax) can be obtained from shear wave velocity (Vs) readings via seismic piezocone tests (SCPTu). The secant stiffness (G), which softens from Gmax corresponding to operational load levels, can be obtained by generating stiffness reduction curves from back analysis of load tests. Then, using appropriate G values, the Q-w curve can be defined for conditions similar to the database from the pseudo strain (w/d). Thus, a complete framework for optimal integration of SCPTu data, Randolph elastic solution and back-analysis of field operational stiffness can be established for complete axial pile foundation analysis.

Jan 1, 2011

By D. Richter

The Pyrometallurgical refining stage of ferronickel manufacturing produces a slag rich in iron and nickel, which is usually further processed for metal recovery. The recovered material is returned to the refining or smelting stages, depending on the amount of impurities. A series of tests was carried out on the Mineração Morro Azul refining slags, aiming at the recovery of the metallic particles through physical processing. Minor changes in the process showed improved results. This paper compares the textures of these slags after being cooled at ambient temperature and granulated under water at high pressure and flow. It concludes that the cooling process is intimately connected to the work index of such slags, thus resulting in direct impact in operating costs.

Jan 1, 2011

By Tiejun Chun, Marcus Emrich, Jian Pan, Deqing Zhu, Vinicius Mendes

"Joint projects of studies of hematite acid pellet have been implemented to develop technological solutions for using Vale hematite pellet feed in Chinese palletizing plant. Beneficial improvements on the pellets quality were achieved by adjusting the blends composition and using new technology of pre-treating the blended pellet feed with HPGR (High Pressure Grinding Roller) on rotary kiln pellet technology. The drop strength of green balls increased from 3.4 to 6.0 times from 0.5m height, at the same time, the bentonite dosage decreased from 1.5wt% to 0.7wt%. The compressive strength of roasted pellets reaches 2500 N/pellet. The reduction swelling index of roasted pellets is below 15%.IntroductionWith the fast development of steel industry in China, the production of pellets has been further expanded. Pellets are used as a high quality charge for blast furnace and the annual output is around 80Mt pellets [1]. According to the developmental trend, sinter will be replaced by pellets due to the larger environmental impact of sintering plants when compared to pelletizing plants. For example, the specific CO2 emission in sintering process is around 2.5 times higher than in pelletizing process. However, the steel industry of China has been confronted with a serious shortage of domestic pellet feed due to the low iron grade of Run-of-Mine ore despite of huge reserves of iron ores [2]. Therefore, more pellet feed, mainly hematite, has been imported to make pellets."

Jan 1, 2011

By T. Gouri Charan

Indian coals, which are of Gondwana origin, contain high amounts of mineral matter, wherein the extraneous material was intimately mixed in the coal matrix during the formation stage, causing a high level of impurity in the run-of-mine (ROM) material. These coals possess difficult to very difficult washability characteristics. Beneficiation of high-ash non-coking coals of India has become the prerequisite for improving the overall economics and efficiency of power generation. The use of dry cleaning systems in India for beneficiation of non-coking coals has gaining renewed interest recently. The benefit of the dry beneficiation process is to exploit the given resources while providing a more reliable and consistent quality fuel with a low operating cost. M/S Allmineral has introduced a technique for the dry beneficiation of coal, which is being tried in India for the treatment of high-ash non-coking coals. The first commercial air jig of 50 t/hr capacity was installed and commissioned to beneficiate high-ash coals of 40 x 5 mm feed with an ash content of 40%; a clean coal product of 33% ash was produced and is being used for a sponge iron plant.

Jan 1, 2011

By Tapiwa Chenje, Victor Olivas, Peter Radziszewski

"Ore breakage and grinding media wear have always been considered and determined separately in laboratory tests. However the two processes are linked with the ore broken down in any comminution device being responsible for the majority of the steel wear experienced. The Comminution Dynamics Laboratory (CDLab) successfully developed a test methodology that can more accurately predict grinding media wear in tumbling mills than the Bond Abrasion test. This paper looks at the possible application of the abrasive wear methodology to determine breakage parameters of the same ore used in the abrasion test. Results indicate that breakage parameters comparable to t10 can be determined using the Steel Wheel Abrasion Test (SWAT), while using significantly less ore than standard breakage tests.BACKGROUNDThe Rubber Wheel Abrasion Test (RWAT) is an internationally accepted and widely used method for determining the abrasion wear behavior of materials. The abrasion wheel test was developed to primarily utilize a steel wheel (Brinell, 1921). Haworth (1949) criticized using of the steel wheel by arguing that increasing the contact area size in the steel wheel test causes a change in the wear rate with time. He suggested that the use of a rubber wheel instead eliminates this problem, leading to the adoption of the RWAT which was standardized in ASTM G65 (2004).Radziszewski (2002), however, found that the use of the Steel Wheel Abrasion Test (SWAT) was more applicable for wear testing in the mining industry for two critical reasons. Firstly, the major cause of wear in a ball mill, the most frequently used comminution device, is ball-ore-ball contact and also ball-ore-liner which both are metal-ore-metal contact. Therefore, using the steel wheel has the advantage of providing a similar abrasive environment to the one that takes place in a real ball mill. Secondly, the SWAT creates the potential of running experiments at much higher force regimes that are closer to what happens in actual mills, unlike the RWAT which is a low stress test."

Jan 1, 2011

By F. Chevarin

The reaction of O2 with the carbon anode is considered as the main parasitic chemical reaction affecting Hall-Heroult process anodes. The current study aims at investigating the influence of the microstructure of baked anode on its overconsumption. Samples were removed from different positions of an industrial anode. Density, porosity, Lc and BET specific surface area were measured. The anode reactivity was evaluated based on the weight losses for the samples resulting from the reaction of anode with air at 550°C after 7h. The essential parameters determined to control the air reactivity are closed porosity, Lc and pores with a pore entrance radius of 1.5, 8.5 and 12 p.m. The knowledge of effects of these parameters allows better understanding of the reactivity of anodes and consequently reduction of their overconsumption in electrolysis bath.

Jan 1, 2011